International Standard

INTERNATIONAL ORGANIZATION FOR STANDARDIZATlONWlE)I(C1YHAPOflHAR OPTAHM3AUMR n0 CTAH,QAPTbl3ALWl~RGANlSATlON INTERNATIONALE DE NORMALISATION

Fasteners - Clearance holes for bolts and screws

&men ts de fixa tion - Trous de passage pour boulons et vis

First edition - 1979-06-01

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 273:1979
https://standards.iteh.ai/catalog/standards/sist/dbd0a47d-9790-4a30-8d71-
b30ccff5af18/iso-273-1979

UDC 621.882.15 Ref. No. IS0 273-1979 (El

Descriptors : fasteners, screws, dimensions, bolts, hole size, dimensional tolerances.

Price based on 2 pages

FOREWORD

IS0 (the International Organization for Standardization) is a worldwide federation

of national standards institutes (IS0 member bodies). The work of developing
International Standards is carried out through IS0 technical committees. Every
member body interested in a subject for which a technical committee has been set
up has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.

Draft International Standards adopted by the technical committees are circulated

to the member bodies for approval before their acceptance as International
Standards by the IS0 Council.

International iTeh STANDARD PREVIEW

Standard IS0 273 was developed by Technical Committee
Fasteners, and was circulated to the member bodies in December 1977.
lSO/TC 2,

It has been approved by the member

(standards.iteh.ai)
bodies of the following countries :

ISO 273:1979
Australia Hungary New Zealand
https://standards.iteh.ai/catalog/standards/sist/dbd0a47d-9790-4a30-8d71-
India Norway
Belgium
Bulgaria Ireland
b30ccff5af18/iso-273-1979
Romania
Canada Italy . Spain
Czechoslovakia Japan Sweden
Denmark Korea, Dem. P. Rep. of Switzerland
Finland Korea, Rep. of Turkey
France Mex ice USA
Germany, F. R. Netherlands Yugoslavia

The member bodies of the following countries expressed disapproval of the

document on technica 1 Y tounds .

South Africa, Rep. of

United Kingdom
USSR

This International Standard cancels and replaces IS0 Recommendation R 273-1962

of which it constitutes a technical revision.

0 International Organization for Standardization, 1979 l

Printed in Switzerland
INTERNATIONAL STANDARD IS0 273-1979 (E)

Fasteners - Clearance holes for bolts and screws

iTeh STANDARD PREVIEW

(standards.iteh.ai)
1 SCOPE AND FIELD OF APPLICATION
ISO 273:1979
This International Standard specifies clearance hole diameters for general purpose applications. These values result from
https://standards.iteh.ai/catalog/standards/sist/dbd0a47d-9790-4a30-8d71-
bearing area calculations in connection with IS0 bolt and nut product standards.
b30ccff5af18/iso-273-1979
NOTE - Clearance holes for special applications should be selected on the basis of design requirements.

1
IS0 273-1979(E)

2 DIMENSIONS
‘//“// \p
,;;;y $.;
, /’,,;,’
/’I / \ ‘V
- -.-
-a=;- a t
~
t I_- t
,/
f ’/ , ,’/ ’ /’ \\. ‘\~
\ \\
/,, ’I’,’,,,’‘/’JQ+ ‘x,
I’ \,:T
/IdA / /’ \\A
Dimensions
-- -- - - in millimetres
I

Clearance hole d,, I Clearance hole dh

Thread Thread
diameter Series : I diameter Series :
d d I
fine medium coarse fine medium coarse
1
1 l,l 12 1,3 42 43 45 48
12 1,3 1,4 13 45 46 48 52
1,4 1,5 1,6 123 48 50 52 56
--
1,6 lP7 13 2 52 54 56 62
1,8 2 a1 22 56 58 62 66
2 22 2,4 28 60 62 66 70

25 2,7
iTeh STANDARD PREVIEW
29 3,l 64 66 70 74
3
3,5
3,2
3,7
(standards.iteh.ai)
3,4
33
3,6
4,2
68
72
70
74
74
78
78
82

4 4,3 4,5 ISO 273:197976

4,8 78 82 86
4,5 4,8 5 80 82
https://standards.iteh.ai/catalog/standards/sist/dbd0a47d-9790-4a30-8d71-
5,3 86 91
5 5,3 5,5 85
5,8b30ccff5af18/iso-273-1979 87 91 96

6 6,4 66 7 * 90 93 96 101
7 7,4 7,6 8 95 98 101 107
8 8,4 9 10 100 104 107 112

10 12 105 109 112 117

12 14,5 110 114 117 122
14 16,5 115 119 122 127
--
16 17 18,5 120 124 127 132
18 19 21 125 129 132 137
20 21 24 130 134 137 144

22 23 24 26 140 144 147 155

24 25 26 28 150 155 158 165
27 28 30 32

30 31 33 35
33 34 36 38
36 37 39 42
39 40 42 45
I

The following tolerance fields are given for information only, for use where it is desirable to specify tolerances :
fine series : HI2
medium series : H13
coarse series : H14

In cases where it is necessary to avoid interference between the edge of the hole and the underhead fillet of the bolt, a
chamfer is recommanded.