MasterSeal® 730 UVS

Pre-Applied Fully Bonded HDPE (High Density Poly Ethylene) Multi Layered Waterproofing Membrane with
unique UV stability for below grade waterproofing

DESCRIPTION Peel Adhesion to 1.8

MasterSeal 730 UVS is an HDPE membrane with Concrete (N/mm),
unique pressure sensitive adhesive to enable good ASTM D903 modified
adhesion with concrete surfaces; and a state of the Tensile retention upon 90
art UV stable top film which chemically bonds and heat aging (%),
becomes monolithic to the overlying layer of fresh ASTM D 412
concrete. Elongation retention upon 80
heat aging (%),
MasterSeal 730 UVS forms an unique integral seal
ASTM D 412
around the concrete poured against it prevents
Resistance to Hydrostatic 61
water ingress even under high hydrostatic pressure
Head (m),
and prevents lateral migration as well.
ASTM D 5385 modified
MasterSeal 730 UVS remains fully adhered to Lateral water migration >61
concrete (i.e. monolithic) helping retain its resistance (m) 23oC,
performance even when there is ground settlement ASTM D5385 modified
beneath the slabs. Lap Peel Adhesion, 1.6
RECOMMENDED USES (N/mm, 23oC),
ASTM D1876 modified
MasterSeal 730 UVS is intended for use in below
Dimensional stability at 0.5%
grade waterproofing applications such as
80oC, ASTM D 1204
basements with high water table and cut & cover
Water vapour 0.005
structures (e.g. tunnels) and allows efficient use of
transmission (perm),
of confined sections.
ASTM E96
FEATURES AND BENEFITS
The performance data is typical and based upon
• Fully Adhered to Poured Concrete – Prevents controlled laboratory conditions. Actual
water migration performance on the job site may vary from these
• Unaffected by hydrostatic pressure – values based on actual site conditions.
Enables application in High water table areas
• Unaffected by Contamination – Does not PROPERTIES
require any special protection during PERFORANCE DATA
construction – can be easily cleaned with water MasterSeal 730 UVS (acrylic finished)
• Simple and Easy to Install – Does not require Release (removal) liner is silicone based with better UV
stability before removing liner
special tools and welding techniques
Thickness, Width 1.2 mm / 1.0 M
• Chemically resistant – Can be used in all Soil Colour White
and Subsoil conditions, even if contaminated MasterSeal 9361
with salts. Thickness / Width 0.3mm/ 80 mm
• Fully adhered watertight laps – Ensures water MasterSeal 9372
tightness
Thickness / Width 0.3mm/ 120 mm
PERFORMANCE DATA
1. MasterSeal 936 is a double side sticky tape
Elongation (%), 550 used for specialized detailing and overlaps.
ASTM D 412
Tensile Strength (MPa), 26.0 2. MasterSeal 937 is a single side sticky tape
ASTM D 412 used for repair and termination of membrane.
Puncture Resistance (N), 1000 ± 5%
ASTM E 154 modified
MasterSeal® 730 UVS
APPLICATION damage to the membrane during laying steel
Surface Preparation reinforcement, consolidation and compaction of
It is essential to create a sound and solid substrate concrete.
to eliminate movement during the concrete pour. Kindly ensure that the plastic liner of the membrane
Substrates must be regular and smooth with no is removed prior to placement of reinforcement.
gaps or voids. Grout around all penetrations for Additionally, during placement of concrete, the
stability vibrator needle should not touch the placed HDPE
Horizontal Blinding – The blinding must be free of membrane. For best results use BASF’s Smart
loose aggregate, voids, surface irregularities and Dynamic Concrete.
sharp protrusions. The surface needs to be in a
PACKAGING
touch dry condition. SDD condition (no standing
MasterSeal 730 UVS is supplied in Rolls of 20m
water) is also acceptable.
length and width of 1.0 m. Each Roll consists of 20
Vertical Surfaces – The vertical surfaces should
have proper levelled brickwork, blockwork or Sq. meter of membrane.
formwork without any irregularities. For the case of MasterSeal 936 is supplied in rolls of 20 / 50m
length and 80 mm width.
sheet piles, the substrate should be made regular
MasterSeal 937 is supplied in rolls of 20 / 50m
with a smooth finished shotcrete or sacrificial
length and 120mm width.
formwork to be installed.
Installation
SHELF LIFE
Please contact our BASF Representative for further
Twelve months if stored in original containers under
support for detailed installation guidelines
dry conditions at a temperature between 10-30° C.
Membrane Repair
Generally, the membrane is very tough and the
PRECAUTIONS
execution should not encounter any repair. In the
For the full health and safety hazard information
most extreme cases, if for some site issues, there
and how to safely handle and use this product,
is any reason to do a patch work, then please
please make sure that you obtain a copy of the
contact our BASF Representative for the
BASF Material Safety Data Sheet (MSDS) from our
rectification procedure.
office or our website.
Pouring of Concrete
It is recommended that concrete is poured within 5
TDS Ref. No.: MasterSeal730UVS/04/0919
weeks after the HDPE layer has been laid on the
sub base (PCC). Care should be taken to avoid any

The technical information and application advice given in this BASF Construction Chemicals publication are based
STATEMENT OF on the present state of our best scientific and practical knowledge. As the information herein is of a general nature,
RESPONSIBILITY no assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user
is responsible for checking the suitability of products for their intended use.
® = registered trademark of BASF group in many countries

Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF Construction
NOTE Chemicals either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they, and not BASF Construction Chemicals, are responsible for carrying out procedures appropriate to a specific
application.
BASF India Limited
Construction Chemicals Division
Plot No 12, TTC Area, Thane Belapur Road, Turbhe
Navi Mumbai – 400705, India
Tel: +91 22 67127600, Fax: +91 22 67917358
Email: [email protected] , www.master-builders-solutions.basf.in