EDWARDS® Catalog u Intelligent Input-Output

LIFE SAFETY & INCIDENT MANAGEMENT

Universal Input/ SIGA-UIO6R

Output Module
Motherboards
SIGA-UIO2R, SIGA-UIO6R,
7300-1657:
0121

SIGA-UIO2R

S3424

Overview Standard Features

Signature Series Universal Input-Output Module Motherboards • Modular flexibility
provide mounting and wiring terminations for up to six Signature Wide assortment of multi-function plug-in modules provides
Series plug-in UIO (SIGA-“M” series) modules. UIO motherboards total flexibility.
slide into a rigid extruded track (included) with mounting pads
• Minimum wiring requirements
for convenient mounting into a variety of equipment enclosures.
Integral jumpers between modules allow sharing of risers to
UIO modules plug into the board and are held securely in place
reduce installation wiring.
with captive machine screws. All field wiring connects to terminal
blocks on the motherboard, which permits rapid removal and • Easy installation
replacement of modules for troubleshooting. #12 AWG (2.5 mm2) terminal blocks and sturdy mounting pads
The SIGA-UIO2R provides mounting and wiring terminations for ensure quick installation into EDWARDS enclosures.
up to two UIO modules, and the SIGA-UIO6R provides mounting • Supports automatic device mapping
and wiring terminations for up to six UIO modules. Both mother- All compatible UIO modules transmit information to the loop
boards feature a riser #1 input and a riser #2 input bus. Jumpers controller regarding their circuit locations with respect to other
on riser #1 input, between modules, facilitate sharing a single riser Signature devices on the wire loop.
among more than one module. This significantly reduces wiring
• Supports intelligent devices
requirements. Removing the jumpers provide separate riser inputs
On-board modules make decisions and input an alarm from
to each adjacent module. Riser #2 input is fixed to each module
initiating devices connected to them even if the loop controller’s
position and cannot be split.
polling interrogation stops.
The SIGA-UIO6 provides mounting and wiring terminations for up
to six UIO modules. This motherboard provides two riser inputs • Twisted or shielded wire not required
that are common to all modules. Because all decisions are made at the on-board modules,
lower communication speeds are possible. This results in
substantially improved control panel response time and less
sensitivity to line noise and loop wiring properties.
• Supports electronic addressing
Programmable addresses are downloaded to compatible UIO
modules from the loop controller, a PC, or the SIGA-PRO
Signature Program/Service Tool. There are no switches or dials
to set.

Page 1 of 4 D ATA S H E E T E85001-0365

Not to be used for installation purposes. Issue 1.1
Mounting and Installation
Mount the UIO motherboard inside a EDWARDS MFC-A cabinet
or other suitable electrical enclosure with screws and washers
provided. Each MFC-A will hold one UIO2R motherboard or one
UIO6 or UIO6R motherboard complete with their full complement
of modules.
Plug a Signature Series UIO module into any available position on
the motherboard and secure the module to the motherboard with
the captive screws. Wiring connections are made to the terminals The MFC-A cabinet is UL listed for use with UIO moth-
erboards and meets requirements for spacing and
on the motherboard (see wiring diagram). UIO motherboard
clearance around the components.
terminals are suited for #12 to #18 AWG (2.5 mm2 to 0.75 mm2)
wire size.
EDWARDS recommends that all boards and modules be installed
according to latest recognized edition of national and local fire
alarm codes. UIO Motherboard

Testing & Maintenance Plug-in (UIO)

The module’s automatic self-diagnosis identifies when it is Module
defective and causes a trouble message. The user-friendly
maintenance program shows the current state of each module
and other pertinent messages. Single modules may be turned off
(de-activated) temporarily, from the control panel.
Scheduled maintenance (Regular or Selected) for proper system
operation should be planned to meet the requirements of the Cabinet or electrical enclosure
Authority Having Jurisdiction (AHJ). Refer to current NFPA 72 and
ULC CAN/ULC 536 standards.

Compatibility
Signature Series Universal Input/Output Module Boards are
compatible only with SIGA-“M” Series I/O Modules, which require
a Signature Data Controller. They are compatible with EST3,
EST3X and iO Series control panels.

Warnings & Cautions

Signature devices will not operate without electrical power. As
fires frequently cause power interruption, we suggest you discuss
further safeguards with your fire protection specialist.

Page 2 of 4 D ATA S H E E T E85001-0365

Not to be used for installation purposes. Issue 1.1
Typical Wiring
Signature Series Universal Input/Output Motherboards have terminal blocks to accept #18 AWG (0.75mm2 ), #16 AWG (1.0mm2),
#14 AWG (1.5mm2 ), and #12 AWG (2.5mm2) wire sizes. See Signature Data Controller catalog sheets for detailed wiring requirements
and specifications.

SIGA-UIO2R SIGA-UIO6R
3 Module Input/Output Wiring
Refer to individual module installation sheet for wiring details.
Module Input/Output Wiring UIO2R

1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 UIO6R
TB1 TB2

TB1

TB2

TB3

TB6
TB4

TB5
Data In
TB7 Data In
Signature 4 TB15 TB7
3
Data 4 Signature
4
2 Common input/output 3
Circuit 1 3
Data TB15
2 bus for M series 2 Input/Output Bus 2
1 Circuit 4
Data Out modules 1 3 Common to all
5 2
1 M series
Data Out modules (maximum
TB8 TB9 current is 8 Amps)
1 2 3 4 1 2 3 4
Jumpers connect common

TB11
TB8

TB9

TB10

TB13
TB12
inputs/outputs between 1
Module Input/Output Wiring modules Jumpers connect 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4
common inputs
3 5 outputs between
Notes

modules. Module Input/Output Wiring (maximum current is 8 Amps)
Refer to individual module installation sheet for wiring details.

1 Jumpers may be used to make the inputs/outputs between

modules common.

2) Not all modules use the SIGA-UIO2R terminals for the same
SIGA-UIO6
functions. Module Input/Output Wiring
Refer to individual module installation sheet for wiring details.
3 Refer to individual SIGA-M series installation sheets for jumper
settings and wiring information. Installations with multiple 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 UIO6
SIGA-UIO motherboards or enclosures (which include other

TB1

TB2

TB3

TB6
TB4

TB5
TB14 Input/Output Bus 1
wiring) require FPL, FPLR, FPLP, or equivalent NEC-approved Data In 4 Common to all
wire for all power limited wiring. Observe the details of
3
2
M series
4 1 modules (maximum
supervision and power limited versus non-power limited Signature
Data
3 current is 8 Amps)
2 TB15
circuits. Refer to the SIGA-M series installation sheets. Circuit 1 4 Input/Output Bus 2
TB7 3 Common to all
2 M series
4) Do not mix incompatible signals. Data Out 1
modules (maximum
current is 8 Amps)
5 Maximum current is 8 Amps.

7) Refer to Signature Data Controller Installation Sheets for wiring

specifications.

Page 3 of 4 D ATA S H E E T E85001-0365

Not to be used for installation purposes. Issue 1.1
 Specifications
Catalog Number SIGA-UIO2R SIGA-UIO6R SIGA-UIO6
Module Capacity Two Six Six
5.4 inch L (across
L I F E S A F E TY & I NCI DE NT M AN AGEM EN T Dimensions (with 9.56 inch L (across mounting feet) x 4.3 inch W
mounting feet) x 4.3
module installed) x 3.2 inch H
Contact us inch W x 3.2 inch H
Phone: 800-655-4497 (Option 4) Address Requirements no address required
Email: [email protected]   Type Code none
Website: edwardsfiresafety.com Compatible Modules All SIGA-Mxxx Signature Series
8985 Town Center Pkwy Operating Voltage 15.2 to 19.95 Vdc (19 Vdc nominal)
Bradenton, FL 34202 Mounting (cabinets) Directly into suitable enclosures (e.g.: MFC-A) - Notes 1, 2, 3.
Wiring Terminals #12 AWG (2.5mm²) to #18 AWG (0.75mm²)
© 2020 Carrier
Operating Temperature: 32°F to 120°F (0°C to 49°C)
All rights reserved. Storage and Operating
Storage Temperature: -4°F to 140°F (-20°C to 60°C)
Environment
Operating and Storage Humidity: 0 to 93% RH
Agency Listing UL, ULC, MEA, CSFM

Notes:
1. Allow a minimum clearance of one inch around all sides of the UIO motherboard.
2. On-site drilling of mounting holes may be required. Self-tapping mounting screws are provided.
3. Suitable cabinets: MFC-A, CAB2, 3-CAB5, 3-CAB7, 3-CAB14, 3-CAB21,
3-RCC series, RACC series.

Ordering Information
Catalog Ship Wt. - lb
Description
Number (kg)
Universal Input-Output Module Board w/Riser Inputs
SIGA-UIO2R 0.32 (0.15)
- Two Module Positions
Universal Input-Output Module Board w/Riser Inputs
SIGA-UIO6R 0.62 (0.28)
- Six Module Positions
Universal Input-Output Module Board
SIGA-UIO6 0.56 (0.25)
- Six Module Positions
UL listed cabinet for mounting UIO motherboards, red with
MFC-A white “FIRE” 8 inch H X 14 inch W X 3.5 inch D (203 mmH 7.0 (3.1)
X 356 mm W X 89 mm D)

03-31-20

Page 4 of 4 D ATA S H E E T E85001-0365

Not to be used for installation purposes. Issue 1.1