Fosroc Reebol constructive solutions

Chemical mould release agent

Uses Properties
■ For quick, clean and easy stripping of moulds and Specific gravity : Typically 0.83 at 20°C
formwork.
Reebol may be used on suitably sealed timber and
■ For high quality, fair-faced and stain-free concrete. polyurethane coated, steel, GRP and other resinous
formwork surfaces.
Advantages
Instructions for use
■ Ensures easy release, reducing damage and improving
efficiency of production. Mould preparation
■ Minimises surface blemishes and staining, promoting All moulds, new or used, must be cleaned of surface deposits
high quality fair-faced concrete even with white cement. of rust, concrete, oil or other materials. Inadequate cleaning
■ Reduces opportunity of damage to formwork, extending may lead to surface blemishes due to the adhering material.
usable life. The use of a proprietary chemical degreaser or acid cleaning
■ Minimises cleaning of formwork before re-use. with Fosroc Acid Etch*† is recommended.
■ Suitable for use with virtually all types of formwork. If only limited use of the formwork is envisaged, new timber
■ Inhibits corrosion of steel formwork. moulds may be coated directly with Reebol. If forms are to be
regularly re-used then the surface should initially be coated
with a suitable polyurethane sealer. This provides increased
Standards compliance
protection to the timber surface, improves ease of cleaning
Category 5: Chemical release agent (Concrete Society: and prevents the build up of large residual levels of release
Notes on formwork release agents and coatings. April 1981). agent in the timber of the form which may lead, over time, to
increased surface dusting or retardation.
Description
Application
Reebol chemical mould release agent is a specially
Reebol can be applied by all normal methods, including
formulated blend of mineral oils and selected additives. It is
brush, sponge and conventional spray. Where suitable, spray
supplied as a low viscosity, pale straw coloured liquid.
application is recommended.
On the mould, Reebol provides a chemical release action that
Non-absorbent surfaces require a single application. New,
is superior to that provided by normal oil based release
unsealed, timber surfaces should be re-coated if delay in use
agents (Concrete Society categories 1 to 4). Entrapment of
of the mould leads to absorption of the release agent into the
air bubbles at the mould surface is minimised, reducing
timber.
surface blemishes and substantially reducing remedial costs.
Coverage rate
As well as improving cast concrete surfaces, Reebol also
minimises damage to form surfaces. Corrosion on steel Depending on the porosity and texture of the mould surface,
moulds is reduced. On all mould types the easier release and typical coverage rates of 20 to 60 m2/litre (0.015 to 0.050
reduced residue minimise the chance of damage to the mould litres/m2) will be obtainable.
surface during stripping and cleaning. This extends the life of
Best results will be obtained with the thinnest practical
the surface and reduces the frequency of concrete defects
coating. Over application should be avoided. Excessive
caused by damage to the mould face.
application on flat surfaces or which leads to pooling of
release agent in the corners of forms is uneconomic and
Technical support
can lead to surface dusting or, in worst cases, surface
Fosroc offers a comprehensive technical support service to retardation.
specifiers, end users and contractors. It is also able to offer
on-site technical assistance, an AutoCAD facility and
Fosroc Reebol

dedicated specification assistance in locations all over the

world.
 Fosroc Reebol
After stripping or demoulding Additional Information

After use, the formwork or mould should be brushed or wiped Fosroc manufactures a wide range of complementary
clean of any excess dust prior to re-application of Reebol for products which include :
the next use of the mould. The use of Reebol minimises the
■ waterproofing membranes & waterstops
amount of time and effort required for this process.
■ joint sealants & filler boards
Repair of moulds
■ cementitious & epoxy grouts
If, after extended use, mould surfaces require repair or re-
coating with polyurethane sealer, all residual traces of Reebol ■ specialised flooring materials
must be removed to ensure complete adhesion. This is best
Fosroc additionally offers a comprehensive package of
effected by using a strong industrial detergent together with
products specifically designed for the repair and
stiff brushing, followed by thorough rinsing with clean water.
refurbishment of damaged concrete. Fosroc’s ‘Systematic
Approach’ to concrete repair features the following :
Limitations
■ hand-placed repair mortars
For application temperatures in excess of 60°C refer to the
Fosroc Technical Department. ■ spray grade repair mortars

■ fluid micro-concretes
Estimating
■ chemically resistant epoxy mortars
Supply
Reebol : 210 litre drums & bulk supply ■ anti-carbonation/anti-chloride protective coatings
Coverage ■ chemical and abrasion resistant coatings
Reebol : 20-60 m2/litre
For further information on any of the above, please consult
Storage your local Fosroc office - as below.

Reebol has a minimum shelf life of 12 months when stored in

the original unopened containers under normal warehouse
conditions.

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the recent version.

Fosroc Chemtech Head Office Alex. Branch

Construction Chemicals 6th of October City, 3rd Industrial Zone, Arab Republic of Egypt. 156 Port-Said St. Al-Ibrahimeya, Kesm
Tel: (02) 38242045 / (02) 38242046 Bab Shark-No.5,1st floor.
Fax: (02) 38242098 Tel: (03) 5925264
E-mail: [email protected]
EG/0327/21/A