PREMIUM

PLANETARY CATALOGUE
 General Information
Introduction :
Premium is a fast growing and leading company in designing
and manufacturing Planetary Gearboxes and Custom made
Gear Boxes that are considered the most important to keep
machines on a continuous run. A noted company having three
decades of considerable understanding in the fabrication of
this rare group of Gears, Premium Planetary Gearbox has
carved a niche for itself for maintaining national and
international standards in terms of precision, distinction and
endurance. 1. Input Shaft (Sun gear Shaft) 5. Planet Washers 9. Ring Gear
Through the years of experience in the field of industrial 2. Input Bearings 6. Planet Carrier 10. Output Shaft
drives, the exactness of application and the proper selection 3. Planets 7. Planet Pin 11. Output Bearing
4. Planet Rollers 8. 'O' rings 12. Circlip
of speed reducer gives a long peak performance. Those meet
the needs in the core sector applications. Selection of Gearbox :
Reducer can be selected by service factor or load
Planetary gearboxes are available in Solid input type, Hollow classification. Both service factors and load classification are
input type (suitable for standard B5 Flange Electric Motor); a means of classifying different equipment and applications
mounting will be flange, foot, shaft mounted. into a uniform guideline useful for reducer selection. Due to
variations in application, service factors are used to adjust
Planetary Design Advantages
equipment ratings to accommodate differing load conditions.
1. Coaxial input and output
2. Compact in construction & light in weight Applications involving unusual or severe load condition
3. Uniform stress distribution should be carefully reviewed before a service factor is
4. Low noise & high efficiency applied. Care must be taken by the customer to isolate the
5. Torque multiplication reducer from unplanned transient load or vibrating conditions.
6. Direct Mounting of Electric & Hydraulic Motors
7. High shock load capacity Before a reducer can be selected for any application, the
8. Longer life & maintenance free equivalent output torque or horse power must be computed
9. Energy saving design by multiplying the actual or specified torque or horsepower by
10. Value for the investment the service factor (SF) for the particular load classification for
which the unit is to be used. It is necessary that the unit
Material of Construction : selected has a capacity equal to or in excess of the equivalent
Planets and sun gears:
output torque or horsepower.
Planets and sun gears are manufactured from high alloy steel
and heat treated for case carburizing to achieve the optimum
Load Nature
strength and wear resistance. Gear Profiles are ground to Duration of Service
reduce noise level and optimized maximum root strength and U M H
minimize sliding contact to ensure high efficiency.
Occasional 0.5 0.8 1.25
Ring Gears : 12 hrs/day
Ring gears are manufactured from high alloy steel and heat Electric Motors Intermittent 0.8 1.0 1.5
treated to absorb impact loads and give desired wear life, the Turbines,
production process selected to avoid distortion of gear teeth Hydraulic Motor 3 hrs/day
due to heat treatment. 3-10 hrs/day 1.0 1.25 1.75
Above 10 hrs 1.25 1.5 2.0
Shafts :
Input and output shafts are manufactured from high alloy per day
steel and toughened for resistant to bending and torsional
stress. Symbols used :

Planet Carriers : fa = Service factor

Planet carriers are manufactured from high alloy steel forging n1 = Input speed (rpm)
or castings for strength and rigidity to ensure equal tooth n2 = Output speed (rpm)
loading on planets. n = Gearbox efficiency
Mtcon = Continuous Torque (Nm)
Housing : Mtpeak = Peak Torque (Nm)
Foot or Flange type casings are of cast iron for strength & Mteq = Equivalent Torque when gearbox
rigidity. is subjected to varying loads (Nm)
02
h = Number of working hours the element, which limits the life of the gearbox. To correlate
P = Actual power of gearbox (kW) the speed and the duration, the torque is expressed as a
Pt = Thermal power of gearbox (kW) function of the product n2x h. with the speed n2 and the torque
HP = Horsepower Mtcon required the duration in hours can be calculated, or
Lf = Load location factor PD
alternatively, if the speed and the duration in hours required
PD = Pitch Diameter (mm)
Fc = Load connection factor are known then the Mtcon that the gearbox can transmit can be
To = Required output Torque (Nm) calculated.
Teq = Equivalent Torque (Nm)
P = Required Mechanical Rating (kW) Example :
Kf = Load correction factor on shaft Expected life in hours = 2500
N1max = Maximum input speed (rpm) Output speed of the gearbox = 20rpm
2500[h] * 20[n2] = 5 000 00 [n2 x h]
Speed:
Input Speed (n1): Thermal Power (Pt )
It represents the actual input speed of the gearbox. Maximum mechanical power transmitted by the gearbox
while operating continuously, with splash lubrication, without
Output Speed (n2): exceeding the thermal limit of gear box (50ºC above the
It represents the actual out speed of the gearbox. ambient temperature). Greater powers can be transmitted by
using an appropriate cooling system. The value refers to
Maximum input Speed (n1max): continuous operation with input speed of 1440 rpm at ambient
It represents the maximum input speed of the gearbox for temperature 30ºC.
the continuous operation that the gearbox can run for the Information required for selection of the reduction unit:
specified life index. - The specific application
- Working life in hours
Reduction Ratio (i): - Input speed
It is the ratio of actual speed to actual output speed - Input Horsepower
i = n1/n2 - Desired output speed
- Over hung load etc.
Torque Ratings: Selection of reducer is based solely on the required
Continuous Torque (Mtcon) output torque capacity of the application at specified life
This is the transmittable torque of the gearbox with duration. The Service factor method is used to apply specific
continuous operation, that guaranties a duration of h hours industry application standards based on the hours per day of
with a gearbox output rotation velocity of n2 RPM. It is operation.
expressed as a function of the product n2 x h
Calculate the desired reducer ratio:
Reducer ratio = Input speed (RPM)/Output speed (RPM)
Peak Torque (Mtpeak):
Select Reduction ratio, that is closest to the desired ratio
This is the maximum torque that the gearbox can transmit
calculated as above.
for short periods of time.
Calculate the equivalent output torque:
When output torque is known (to)
Equivalent Torque (Mteq):
Equivalent Output torque (Teq) =
It represents the value of the constant torque, which
Output Torque (To ) x service factor (fs)
determines the same duration in hours of the torque induced
When input motor horse power is known
by the work cycle. If T21, T2n are the torque transmitted by the Output torque (Nm) = (7123.77 x HP x fs x Eff)
gearbox at the output velocity n21, n2n for the time duration in Output speed
hours of h1, hn, the equivalent torque is:
Where : HP = Input Power in horsepower
Mteq = fs = Service Factor from above
[( ( (n21 * h1)/(n2 * h) * T216.61) + ….+ ( ( (n2n* hn)/(n2* h) )*T2b6.61)]1/6.61 Eff = Drive Efficiency
(single = 98%, double = 96%, triple = 94%, four = 92%)
6.61
n21 *h1 6.61 n *hn 6.61
Teq = *T21 + ….+ 2n *T2n Decide the life index (n2 x h) of the gearbox
n2 *h n2 *h

Where, Life index (n2 x h) = output speed x life required in hours

n2*h = (n21 * h1) + (n22 * h2) + ……. + (n2n * hn)
Example
Lifetime (n2x h) Output speed (n2) = 50rpm
It is the product of output speed and the duration in hours. Life required (h) = 20000 hours
It represents a number proportional to the stress applied to Life index (n2 x h) = 50 x 20000 = 1000000
03
Select Reducer
Locate the reduction ratio determined as above. Locate the Fr
smallest model, that offers the output torque (N-m.) rating
that is equal to or greater than the equivalent output torque
Seal
determined as above for the required reduction ratio and for
required life index (n2 x h).
i.e. Teq must be less than or equal to Mtcon of the
gearbox also peak torque requirement of the application must
be less than the Mtpeak of the gearbox.

Check thermal capacity (Pt)

e
The motor horsepower capacity must be compared to the
thermal capacity of the reducer and select the rating. Which
corresponds to the reducer mode. If the motor horsepower is Where :
less then or equal to the rating, your application will not be
thermally limited with respect to horsepower. If your motor Hp : Horsepower without service factor.
horsepower exceeds this rating, contact the factory to review PD : Pitch Diameter of sprocket, pinion pulley.
the possibility of increasing the thermal capacity by use of a RPM : Shaft revolutions per minute.
heat exchanger. Thermal ratings can be ignored if Fc : Load correction factor.
continuous running time does not exceed idle time on a per
Load correction factor selection table :
hour basis.
Load correction factor (Fc)
Check over hung load
When over hung load exists on either input or output
Sprocket or Timing Belt * 1
shafts, check that the overhung load exerted on input and
Machined Pinion or Gear * 1.25
output shaft are lower than or equal to values indicated in the V-Belt 1.5
chart for selected reducer model. Flat Belt 2.5
In case they are greater than indicated value, change * Refer all multiple chain sprocket and pinion mounted.
gearbox output version, gearbox size or system bearing
arrangement. For correct modification according to your If the actual overhung load exceeds the specified
requirement contact factory. capacity, the following may assist to reduce the overhung
load on the shaft bearings.
Check the braking torque :
When drives are equipped with brakes on the input and 1. Increase the pitch diameter of gear, Pulley or sprocket.
the torque rating of the brake exceeds the rating of the 2. Locate the sprocket or belt closer to the Seal Cage.
motors, the rating of the brake dictates the selection of the 3. Go to the next larger reducer series.
reducer.
Check Dimensions :
Calculations of the overhung load :
The centerline of the overhung load should be as close as Dimension drawings for reducers are given in the
possible to the seal cage to minimize bearing load and catalogue for free input and hollow input with foot and flange
improve bearing life. The formula for determining overhung mounting. For your specific requirement contact the factory.
load in N. is as follows :
Overhung load (N) =
(14247550.5 x HP x Fc) / (PD x RPM (output))

04
 LOAD CLASSIFICATION BY APPLICATION

U=Uniform load H=Heavy shock load M=Moderate shock load

Driven Load Driven Load Driven Load Driven Load

Machine Type Machine Type Machine Type Machine Type

Agitators Elevators Merry-go-roundconveyor M felt whipper H

Pure Liquid U Bucket-uniform load U roll case H jordans M
Liquids & Solids M bucket-continuous U slab conveyor H fog haul H
Liquid-variable density M centrifugal discharge U small waste conveyor-belt U presses M
escalators U small waste conveyor-chain U pulp machine reel M
Blowers freight M sorting table M suction roll M
Centrifugal U gravity discharge U tipple hoise conveyor M washers & thickeners M
Lobe M tipple hoise drive M winders M
Vane U Fans transfer conveyor M
Centrifugal U transfer roll M Printing Presses
Brewing and distilling Induced draft M tray drive M barge haul H
Bottling Machinery U large, mine etc. M trimmer feed M Pumps centrifugal U
Brew. kettles cont. duly U large, industrial M waste conveyor M proportioning M
Cookers cont. duly U light, small diameter U reciprocation single acting
Mash tubs cont. duty U Machine tools 3 or more cylenders M
Scale hopper M Feeders bending roll M rotary-gear type U
Can filling M/C U apron M punch press-gear driver H rotary-lobe, vane U
Cane kniges M belt M plate planners H Rubber and plastic industries
Car Dumpers H disc U tapping machine H crackers H
Car pulleys M reciprocating H Other machine tools laboratory, equipment M
Classifiers M screw M Main drives M mixed minds H
Anxillary drives U refiners M
Clay working machinery Food Industry rubber calenders M
Bick press H beef slicer M Metal mllis rubber mill-2 on line M
Briquette Machine H cereal cooker U Draw bench carriage M rubber mill-3 on line M
Clay working machinery M dough mixer M Main Drive M sheeter M
Pug mill M meat grinders M slitters M tubers and strainers M
Generators-not-welding U warning mills M
Compressors Hammer mills H Table conveyors Sand multer M
Centrifugal U non-reversing group drives M
Lobe M Hoists individual drives H Sewage disposal equipment
Reciprocating-Multi-Cyl. M heavy duty H Revirsing wire drawing M bar screens U
Single-Cyl. H medium duty M flattening machine M chemical feeders U
skip hoist M wire winging machine M collectors U
Conveyor-uniformly loaded Laundry machines Mill-rotary type ball H de watering screws M
Apron U Laundry washers reverse M cement kilns H scum breakers M
Assembly U Laundry tumbler M dryers and coolers H slow or rapid mixers M
Belt U kilns, other than-cement H thickeners M
Bucket U Line shafts pebble H vacuum filters M
Chain U processing equipment M rod plain H
Flight U light applications U wedge bar H Screens
Oven U other line shafts U tumbling barrels H air washing U
Screw U Lumber industry rotary-stone or gravel M
barkers-Hydraulic M Mixers travelling water intake U
Conveyor-heavy duty barkers-mechanical M concrete mixers-cont. M Slab pushers M
Apron M burner conveyor M concrete mixers-int. M Steering gear Stokers U
Assembly M chain saw and drag saw H constant density U
Belt M chain transfer H Variable density M Sugar industry
Bucket M craneway transfer H Oil industry Cane knives M
Chain M de-barking drum H chillers M crushers M
Flight M edger feeder M paraffin filter press M mills M
Live roll H gang feedr M rotary klins M
Oven M green chain M Textile industry
Reciprocating H live rolls H Paper mills batchers M
Screw M log deck H agitators, (Mixers) M calenders M
Shaker H log houl-incline H barker-auxiliaries hydraulic M cards M
Cranes log houl-wll type H barker-mechanical H dry cans M
Main hoists U log turning device H barking drum H dryers M
Bridge travel H main log coveyor H beater and pulper M dyeing machinery M
Trolley travel H off bearing rolls M bleacher U knitting machines looms M
planer feed chains M calender U mangles M
Dredges planer floor chains M caenders-super H nappers M
Cable reels M planer tilting noise M pads M
Conveyors M Converting machine range drives slashers M
Cutter Head drives H Crusher except cutters, palters M soapers M
Jig drives H ore H conveyors U spinners M
Maneuvering Winches M stone H couch M tenter frames M
Pumps M Sugar H cutters-plates H washers M
Screen drive H cylinders M winders M
Stackers M dyers M
Utility winches M felt stretcher M

05
 Rated Torque (in Nm)
MODEL PR1011 PR1211 PR1511 PR1711 PR2011 PR2511 PR2711 PR3011 PR3511 PR3711 PR4011 PR4511 PR5011 MODEL PR6011 PR7011 PR8011 PR9011 PR10011 PR12011 PR14011 PR16011
RATIO RATIO
3.5 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 3.5 47750 74000 114150 169900 265500 474170 770800 1169350
3.8 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 3.8 43100 68400 105550 157550 245500 438500 712250 1080750
4.3 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 4.3 39000 62000 95200 142800 223000 398150 646500 981000
5.8 30 135 400 520 790 1220 1900 2500 4220 5490 6730 10530 15470 5.8 28600 45400 70100 104650 163000 291250 473250 718250
7.2 20 100 280 370 570 850 1320 1720 2900 3800 4650 7400 11000 7.2 20300 32300 50350 75000 117000 209250 340000 616250
PR1021 PR1221 PR1521 PR1721 PR2021 PR2521 PR2721 PR3021 PR3521 PR3721 PR4021 PR4521 PR5021 MODEL PR6021 PR7021 PR8021 PR9021 PR10021 PR12021 PR14021 PR16021
MODEL
PR2522 PR3022
RATIO RATIO
12.1 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 12.1 47750 74000 114150 169900 265500 474170 770800 1169350
14.8 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 14.8 47750 74000 114150 169900 265500 474170 770800 1169350
16.3 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 16.3 43100 68400 105550 157550 245500 438500 712250 1080750
18.1 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 18.1 39000 62000 95200 142800 223000 398150 646500 981000
20.1 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 20.1 47750 74000 114150 169900 265500 474170 770800 1169350
22.0 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 22.0 43100 68400 105550 157550 245500 438500 712250 1080750
24.6 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 24.6 39000 62000 95200 142800 223000 398150 646500 981000
27.5 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 27.5 43100 68400 105550 157550 245500 438500 712250 1080750
30.7 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 30.7 39000 62000 95200 142800 223000 398150 646500 981000
33.3 30 135 400 520 790 1220 1900 2500 4220 5490 6730 10530 15470 33.3 28600 45400 70100 104650 163000 291250 473250 718250
41.5 30 135 400 520 790 1220 1900 2500 4220 5490 6730 10530 15470 41.5 28600 45400 70100 104650 163000 291250 473250 718250
51.8 20 100 280 370 570 850 1320 1720 2900 3800 4650 7400 11000 51.8 20300 32300 50350 75000 117000 209250 340000 616250
PR1031 PR1231 PR1531 PR1731 PR2031 PR2531 PR2731 PR3031 PR3531 PR3731 PR4031 PR4531 PR5031 PR6031 PR7031 PR8031 PR9031 PR10031 PR12031 PR14031 PR16031
MODEL MODEL
PR1532 PR2732 PR3532 PR4532 PR5032
RATIO RATIO
56.6 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 56.6 47750 74000 114150 169900 265500 474170 770800 1169350
63.2 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 63.2 47750 74000 114150 169900 265500 474170 770800 1169350
69.9 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 69.9 47750 74000 114150 169900 265500 474170 770800 1169350
76.7 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 76.7 47750 74000 114150 169900 265500 474170 770800 1169350
85.5 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 85.5 47750 74000 114150 169900 265500 474170 770800 1169350
93.9 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 93.9 43100 68400 105550 157550 245500 438500 712250 1080750
104.7 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 104.7 39000 62000 95200 142800 223000 398150 646500 981000
115.9 80 220 630 860 1320 2020 3160 4160 6950 9100 11070 17300 25350 115.9 47750 74000 114150 169900 265500 474170 770800 1169350
127.2 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 127.2 43100 68400 105550 157550 245500 438500 712250 1080750
141.8 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 141.8 39000 62000 95200 142800 223000 398150 646500 981000
158.7 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 158.7 43100 68400 105550 157550 245500 438500 712250 1080750
177.0 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 177.0 39000 62000 95200 142800 223000 398150 646500 981000
198.0 70 200 590 790 1210 1880 2950 3850 6410 8350 10250 15960 23410 198.0 43100 68400 105550 157550 245500 438500 712250 1080750
220.8 50 180 530 720 1100 1710 2650 3470 5800 7560 9260 14460 21210 220.8 39000 62000 95200 142800 223000 398150 646500 981000
239.7 30 135 400 520 790 1220 1900 2500 4220 5490 6730 10530 15470 239.7 28600 45400 70100 104650 163000 291250 473250 718250
299.1 30 135 400 520 790 1220 1900 2500 4220 5490 6730 10530 15470 299.1 28600 45400 70100 104650 163000 291250 473250 718250
373.2 20 100 280 370 570 850 1320 1720 2900 3800 4650 7400 11000 373.2 20300 32300 50350 75000 117000 209250 340000 616250

PR1041 PR1241 PR1541 PR1741 PR2041 PR2541 PR2741 PR3041 PR3541 PR3741 PR4041 PR4541 PR5041 PR6041 PR7041 PR8041 PR9041 PR10041 PR12041 PR14041 PR16041
MODEL MODEL
PR3542 PR3742 PR4542 PR5042
RATIO RATIO
327 80 220 630 860 1320 2020 3160 4160 6950 9100 327 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
333 80 220 630 860 1320 2020 3160 4160 6950 9100 333 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
359 70 200 590 790 1210 1880 2950 3850 6410 8350 359 10250 15960 23410 43100 68400 105550 157550 245500 438500 712250 1080750
400 70 200 590 790 1210 1880 2950 3850 6410 8350 400 10250 15960 23410 43100 68400 105550 157550 245500 438500 712250 1080750
408 80 220 630 860 1320 2020 3160 4160 6950 9100 408 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
443 80 220 630 860 1320 2020 3160 4160 6950 9100 443 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
455 80 220 630 860 1320 2020 3160 4160 6950 9100 455 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
494 80 220 630 860 1320 2020 3160 4160 6950 9100 494 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
503 80 220 630 860 1320 2020 3160 4160 6950 9100 503 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
552 80 220 630 860 1320 2020 3160 4160 6950 9100 552 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
604 50 180 530 720 1100 1710 2650 3470 5800 7560 604 9260 14460 21210 39000 62000 95200 142800 223000 398150 646500 981000
669 80 220 630 860 1320 2020 3160 4160 6950 9100 669 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
689 80 220 630 860 1320 2020 3160 4160 6950 9100 689 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
734 70 200 590 790 1210 1880 2950 3850 6410 8350 734 10250 15960 23410 43100 68400 105550 157550 245500 438500 712250 1080750
754 50 180 530 720 1100 1710 2650 3470 5800 7560 754 9260 14460 21210 39000 62000 95200 142800 223000 398150 646500 981000
769 80 220 630 860 1320 2020 3160 4160 6950 9100 769 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
818 50 180 530 720 1100 1710 2650 3470 5800 7560 818 9260 14460 21210 39000 62000 95200 142800 223000 398150 646500 981000
844 70 200 590 790 1210 1880 2950 3850 6410 8350 844 10250 15960 23410 43100 68400 105550 157550 245500 438500 712250 1080750
916 70 200 590 790 1210 1880 2950 3850 6410 8350 916 10250 15960 23410 43100 68400 105550 157550 245500 438500 712250 1080750
1021 50 180 530 720 1100 1710 2650 3470 5800 7560 1021 9260 14460 21210 39000 62000 95200 142800 223000 398150 646500 981000
1041 80 220 630 860 1320 2020 3160 4160 6950 9100 1041 11070 17300 25350 47750 74000 114150 169900 265500 474170 770800 1169350
1108 30 135 400 520 790 1220 1900 2500 4220 5490 1108 6730 10530 15470 28600 45400 70100 104650 163000 291250 473250 718250
1143 70 200 590 790 1210 1880 2950 3850 6410 8350 1143 10250 15960 23410 43100 68400 105550 157550 245500 438500 712250 1080750
1274 50 180 530 720 1100 1710 2650 3470 5800 7560 1274 9260 14460 21210 39000 62000 95200 142800 223000 398150 646500 981000
1383 30 135 400 520 790 1220 1900 2500 4220 5490 1383 6730 10530 15470 28600 45400 70100 104650 163000 291250 473250 718250
1590 50 180 530 720 1100 1710 2650 3470 5800 7560 1590 9260 14460 21210 39000 62000 95200 142800 223000 398150 646500 981000
1726 30 135 400 520 790 1220 1900 2500 4220 5490 1726 6730 10530 15470 28600 45400 70100 104650 163000 291250 473250 718250
2154 30 135 400 520 790 1220 1900 2500 4220 5490 2154 6730 10530 15470 28600 45400 70100 104650 163000 291250 473250 718250

06
 THERMAL RATING IN (kW)

MODEL RATIO kW MODEL RATIO kW

PR1011 3.5 -7.2 0.5 PR1021 12.1 -51.8 0.5

PR1211 3.5 -7.2 0.75 PR1221 12.1 -51.8 0.75
PR1511 3.5 -7.2 1 PR1521 12.1 -51.8 1
PR1711 3.5 -7.2 3.7 PR1721 12.1 -51.8 2.5
PR2011 3.5 -7.2 4.2 PR2021 12.1 -51.8 3
PR2511 3.5 -7.2 5 PR2521 12.1 -51.8 3.7
PR2711 3.5 -7.2 7.5 PR2522 12.1 -51.8 5
PR3011 3.5 -7.2 10 PR2721 12.1 -51.8 5
PR3511 3.5 -7.2 18 PR2722 12.1 -51.8 6
PR3711 3.5 -7.2 22 PR3021 12.1 -51.8 7.5
PR4011 3.5 -7.2 25 PR3521 12.1 -51.8 15
PR4511 3.5 -7.2 33 PR3721 12.1 -51.8 18
PR5011 3.5 -7.2 60 PR4021 12.1 -51.8 22
PR4521 12.1 -51.8 30
PR5021 12.1 -51.8 45
PR5022 12.1 -51.8 50
PR6021 12.1-51.8 50
PR7021 12.1-51.8 60
PR8021 12.1-51.8 65
PR9021 12.1-51.8 70

MODEL RATIO kW MODEL RATIO kW

PR1031 56.6-373.2 0.5 PR1041 400-2154 0.5

PR1231 56.6-373.2 0.75 PR1241 400-2154 0.75
PR1531 56.6-373.2 1 PR1541 400-2154 1
PR1731 56.6-373.2 2.2 PR1741 400-2154 2.2
RP2031 56.6-373.2 2.6 PR2041 400-2154 2.6
PR2531 56.6-373.2 3 PR2541 400-2154 3
PR2731 56.6-373.2 3.7 PR2741 400-2154 3.7
PR3031 56.6-373.2 5 PR3041 400-2154 5
PR3531 56.6-373.2 10 PR3541 400-2154 10
PR3532 56.6-373.2 12.5 PR3542 400-2154 12.5
PR3731 56.6-373.2 12.5 PR3741 400-2154 12.5
PR4031 56.6-373.2 15 PR3742 400-2154 15
PR4531 56.6-373.2 18 PR4041 400-2154 15
PR4532 56.6-373.2 25 PR4541 400-2154 18
PR5031 56.6-373.2 30 PR4542 400-2154 25
PR5032 56.6-373.2 35 PR5041 400-2154 30
PR6031 56.6-373.2 35 PR5042 400-2154 35
PR7031 56.6-373.2 40 PR6041 400-2154 35
PR8031 56.6-373.2 45 PR7041 400-2154 40
PR9031 56.6-373.2 47 PR8041 400-2154 45
PR10031 56.6-373.2 50 PR9041 400-2154 47
PR12031 56.6-373.2 65 PR10041 400-2154 50
PR12041 400-2154 65
PR14041 400-2154 70
PR16041 400-2154 85

07
 SELECTION CHART
BASED ON 1440 INPUT RPM AND FS=1
FS 63 71 80 90 90 100 112 132 132 160 160 160 180 180 200 225 225 250 250
HP 0.25 0.5 1 1.5 2 3 5 7.5 10 12.5 15 20 25 30 40 50 60 75 100
O/P
Ratio Speed
3.5 411.43 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
3.8 378.95 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
4.26 338.03 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
5.77 249.57 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
7.2 200.00 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
12.1 119.01 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
14.8 97.30 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
16.3 88.34 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
18.1 79.56 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
20.1 71.64 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
22 65.45 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
24.6 58.54 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
27.5 52.36 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
30.7 46.91 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
33.3 43.24 PR1221 PR1221 PR1521 PR1521 PR1721 PR1721 PR2522 PR2522 PR2722 PR3021 PR3521 PR3521 PR4521 PR4521 PR5021 PR5022 PR5022 PR5022 PR6021
41.5 34.70 PR1221 PR1221 PR1521 PR1521 PR1721 PR2021 PR2522 PR2522 PR3021 PR3521 PR3521 PR3721 PR4521 PR4521 PR5021 PR5022 PR5022 PR6021 PR6021
51.8 27.80 PR1221 PR1521 PR1521 PR2021 PR2021 PR2521 PR2721 PR3521 PR3021 PR3721 PR3721 PR4521 PR4521 PR5022 PR5022 PR6021 PR6021 PR6021 PR7021
56.6 25.44 PR1031 PR1231 PR1531 PR1531 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR5032 PR7031 PR7031 PR7031 PR7031
63.2 22.78 PR1031 Pr1231 Pr1531 PR1531 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR5032 PR7031 PR7031 PR7031 PR7031
69.9 20.60 PR1231 PR1231 PR1531 PR1531 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR5032 PR7031 PR7031 PR7031 PR7031
76.7 18.77 PR1231 PR1231 PR1531 PR1531 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR5032 PR7031 PR7031 PR7031 PR7031
85.5 16.84 PR1231 PR1231 PR1531 PR1731 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR5032 PR7031 PR7031 PR7031 PR7031
93.9 15.34 PR1231 PR1531 PR1531 PR1731 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR5032 PR7031 PR7031 PR7031 PR7031
104.7 13.75 PR1231 PR1531 PR1531 PR2031 PR2731 PR2731 PR3031 PR3531 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
115.9 12.42 PR1231 PR1531 PR1531 PR2031 PR2731 PR2731 PR3531 PR3531 PR3731 PR4031 PR4532 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
127.2 11.32 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3531 PR3531 PR3731 PR4031 PR4532 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
141.8 10.16 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3531 PR3531 PR3731 PR4031 PR4532 PR4532 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
158.7 9.07 PR1231 PR1531 PR1731 PR2031 PR2731 PR3031 PR3531 PR3531 PR4031 PR4532 PR4532 PR4532 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
177 8.14 PR1231 PR1531 PR2031 PR2531 PR2731 PR3031 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
198 7.27 PR1231 PR1531 PR2031 PR2731 PR3031 PR3531 PR3531 PR4531 PR4532 PR4532 PR4532 PR6031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
220.8 6.52 PR1231 PR1731 PR2031 PR2731 PR3031 PR3531 PR3531 PR4531 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
239.7 6.01 PR1231 PR2031 PR2531 PR2731 PR3031 PR3531 PR4031 PR4531 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031
299.1 4.81 PR1531 PR2031 PR2731 PR3031 PR3531 PR3731 PR4531 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031 PR9031 PR9031 PR10031 PR10031
327 4.40 PR1541 PR1741 PR2541 PR2741 PR3542 PR3542 PR4041 PR5042 PR5042 PR5042 PR5042 PR6041 PR7041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041
359 4.01 PR1541 PR2041 PR2541 PR2741 PR3542 PR3542 PR4041 PR5042 PR5042 PR5042 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041
400 3.60 PR1541 PR2041 PR2741 PR3041 PR3542 PR3542 PR4041 PR5042 PR5042 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041
443 3.25 PR1541 PR2041 PR2741 PR3041 PR3542 PR3542 PR4041 PR5042 PR5042 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041
455 3.16 PR1541 PR2041 PR2741 PR3041 PR3542 PR3742 PR4542 PR5042 PR5042 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041
494 2.91 PR1541 PR2041 PR2741 PR3041 PR3542 PR3742 PR4542 PR5042 PR5042 PR6041 PR6041 PR7041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041
503 2.86 PR1541 PR2041 PR2741 PR3041 PR3542 PR3742 PR4542 PR5042 PR5042 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041
552 2.61 PR1741 PR2541 PR2741 PR3041 PR3542 PR3742 PR4542 PR5042 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041
604 2.38 PR2041 PR2541 PR3041 PR3541 PR3742 PR4041 PR5041 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041
689 2.09 PR1741 PR2541 PR3041 PR3541 PR3742 PR4041 PR4542 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR10041 PR12041
734 1.96 PR2041 PR2541 PR3541 PR3541 PR3742 PR4541 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041
754 1.91 PR2041 PR2741 PR3541 PR3541 PR3742 PR4541 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041
769 1.87 PR2041 PR2541 PR3041 PR3541 PR3742 PR4541 PR5041 PR6041 PR6041 PR6041 PR7041 PR8041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041
818 1.76 PR2041 PR2741 PR3541 PR3741 PR4041 PR4541 PR5041 PR6041 PR7041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041
844 1.71 PR2041 PR2741 PR3541 PR3541 PR3742 PR4541 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041
916 1.57 PR2041 PR3041 PR3541 PR3741 PR4041 PR4541 PR5041 PR6041 PR7041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041
1021 1.41 PR2541 PR3041 PR3541 PR3741 PR4541 PR5041 PR6041 PR6041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041
1041 1.38 PR2041 PR3041 PR3541 PR4041 PR4541 PR4542 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041
1108 1.30 PR2741 PR3541 PR3741 PR4541 PR5041 PR6041 PR6041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041
1274 1.13 PR2541 PR3041 PR3741 PR4541 PR4542 PR5041 PR6041 PR7041 PR8041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
1383 1.04 PR2741 PR3541 PR4041 PR4541 PR5041 PR6041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041
1590 0.91 PR3041 PR3541 PR4041 PR4541 PR5041 PR6041 PR6041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041
1726 0.83 PR3041 PR3541 PR4541 PR5041 PR6041 PR6041 PR7041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 *
2154 0.67 PR3541 PR3741 PR4541 PR6041 PR6041 PR7041 PR8041 PR9041 PR10041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * *

08
 SELECTION CHART
BASED ON 1440 INPUT RPM AND FS=1.5
FS 63 71 80 90 90 100 112 132 132 160 160 160 180 180 200 225 225 250 250
HP 0.25 0.5 1 1.5 2 3 5 7.5 10 12.5 15 20 25 30 40 50 60 75 100
Ratio O/P
Speed
3.5 411.43 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
3.8 378.95 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
4.26 338.03 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
5.77 249.57 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
7.2 200.00 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
12.1 119.01 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
14.8 97.30 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
16.3 88.34 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
18.1 79.56 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
20.1 71.64 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
22 65.45 Pr1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
24.6 58.54 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3721 PR4021 PR4021 PR4521 PR5021 PR5021 PR5022 PR5022
27.5 52.36 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3721 PR4021 PR4521 PR4521 PR5021 PR5021 PR5022 PR5022
30.7 46.91 PR1221 PR1221 PR1521 PR1521 PR1721 PR1721 PR2522 PR2722 PR2722 PR3021 PR3721 PR3721 PR4021 PR4521 PR4521 PR5021 PR5021 PR5022 PR6021
33.3 43.24 PR1221 PR1221 PR1521 PR1521 PR1721 PR2021 PR2721 PR2722 PR3021 PR3721 PR3721 PR3721 PR4021 PR4521 PR4521 PR5021 PR6021 PR6021 PR5022
41.5 34.70 PR1221 PR1521 PR1521 PR1721 PR2021 PR2521 PR2721 PR3021 PR3521 PR3721 PR3721 PR4021 PR4521 PR4521 PR5021 PR6021 PR6021 PR6021 PR6021
51.8 27.80 PR1521 PR1521 PR2021 PR2521 PR2521 PR2721 PR3521 PR3521 PR3721 PR4021 PR4521 PR5021 PR5021 PR6021 PR6021 PR6021 PR7021 PR7021 PR8021
56.6 25.44 PR1231 PR1231 PR1531 PR1731 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
63.2 22.78 PR1231 PR1531 PR1531 PR1731 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
69.9 20.60 PR1231 PR1531 PR1531 PR1731 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4031 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
76.7 18.77 PR1231 PR1531 PR1531 PR1731 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
85.5 16.84 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
93.9 15.34 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4532 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR8031
95.7 15.05 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
104.7 13.75 PR1531 PR1531 PR2031 PR2531 PR2731 PR2731 PR3532 PR3532 PR4031 PR4532 PR4532 PR5031 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
106.7 13.50 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3532 PR3731 PR3731 PR4031 PR4532 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR8031
115.9 12.42 PR1231 PR1531 PR2031 PR2031 PR2731 PR3031 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
117.16 12.29 PR1531 PR1531 PR2031 PR2531 PR2731 PR2731 PR3531 PR3731 PR4031 PR4031 PR4532 PR5031 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
127.2 11.32 PR1531 PR1531 PR2031 PR2531 PR2731 PR3031 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
130.66 11.02 PR1531 PR1531 PR2031 PR2531 PR2731 PR2731 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
141.8 10.16 PR1531 PR1531 PR2031 PR2531 PR2731 PR3031 PR3531 PR4031 PR4532 PR4532 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
144.57 9.96 PR1531 PR1531 PR2031 PR2531 PR3031 PR3531 PR3531 PR4031 PR4532 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
158.7 9.07 PR1531 PR1731 PR2031 PR2531 PR3031 PR3531 PR3531 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
177 8.14 PR1531 PR1731 PR2531 PR2731 PR3031 PR3532 PR3731 PR4531 PR4532 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031
192.1 7.50 PR1531 PR2031 PR2731 PR3031 PR3531 PR3532 PR4532 PR5031 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR9031 PR9031 PR10031 PR10031
198 7.27 PR1531 PR1731 PR3031 PR3531 PR3531 PR3531 PR4031 PR4531 PR4532 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031
220.8 6.52 PR1531 PR2031 PR3031 PR3531 PR3531 PR3531 PR4532 PR4531 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031
239.7 6.01 PR1731 PR2531 PR3031 PR3531 PR3532 PR3731 PR4531 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR9031 PR9031 PR10031 PR10031 PR12031
299.1 4.81 PR2031 PR2531 PR3031 PR3531 PR3731 PR4031 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR10031 PR10031 PR14031 PR12031
327 4.40 PR1541 PR2041 PR2741 PR3041 PR3542 PR3742 PR4542 PR5042 PR5042 PR6041 PR6041 PR7041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041
359 4.01 PR1741 PR2041 PR2741 PR3541 PR3542 PR3742 PR4542 PR5042 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041
400 3.60 PR1741 PR2541 PR3041 PR3541 PR3542 PR4041 PR4542 PR5042 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041
443 3.25 PR1741 PR2541 PR3041 PR3541 PR3742 PR4041 PR4542 PR5042 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041
455 3.16 PR1741 PR2541 PR3041 PR3541 PR3742 PR4041 PR4542 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041
494 2.91 PR2041 PR2541 PR3041 PR3541 PR3742 PR4041 PR5042 PR6041 PR6041 PR6041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041
503 2.86 PR2041 PR2541 PR3041 PR3541 PR3742 PR4041 PR5042 PR6041 PR6041 PR6041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041
552 2.61 PR2041 PR2541 PR3041 PR3541 PR3742 PR4541 PR5042 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041
604 2.38 PR2541 PR2741 PR3541 PR3741 PR4041 PR4541 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041
689 2.09 PR2041 PR2741 PR3541 PR3741 PR4041 PR4542 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041
734 1.96 PR2541 PR3041 PR3541 PR3741 PR4541 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041
754 1.91 PR2541 PR3041 PR3541 PR4041 PR4541 PR5041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
769 1.87 PR2541 PR3041 PR3541 PR4541 PR4541 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041
818 1.76 PR2541 PR3041 PR4041 PR4541 PR4541 PR5042 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
844 1.71 PR2541 PR3041 PR3541 PR4041 PR4541 PR5041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
916 1.57 PR2541 PR3541 PR3741 PR4041 PR4542 PR5042 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
1021 1.41 PR2741 PR3541 PR3741 PR4541 PR5041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041
1041 1.38 PR3041 PR3541 PR3741 PR4541 PR4542 PR5042 PR6041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR16041
1108 1.30 PR3041 PR3541 PR4541 PR5041 PR6041 PR6041 PR7041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR15041 PR16041 *
1274 1.13 PR3041 PR3541 PR4541 PR4541 PR5041 PR6041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041
1383 1.04 PR3041 PR3741 PR4541 PR5041 PR6041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * *
1590 0.91 PR3041 PR3541 PR4541 PR5041 PR6041 PR6041 PR7041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 *
1726 0.83 PR3541 PR4041 PR5041 PR6041 PR 6041 PR7041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * * *
2154 0.67 PR3541 PR4541 PR6041 PR6041 PR7041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * * * *

09
 SELECTION CHART
BASED ON 1440 INPUT RPM AND FS=2
FS 63 71 80 90 90 100 112 132 132 160 160 160 180 180 200 225 225 250 250
HP 0.25 0.5 1 1.5 2 3 5 7.5 10 12.5 15 20 25 30 40 50 60 75 100
Ratio O/P
Speed
3.5 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
3.8 378.95 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
4.26 338.03 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
5.77 249.57 PR1011 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
7.2 200.00 PR1211 PR1211 PR1511 PR1511 PR1711 PR1711 PR2011 PR2511 PR2711 PR3011 PR3011 PR3011 PR3511 PR3511 PR3711 PR4511 PR4511 PR5011 PR5011
12.1 119.01 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
14.8 97.30 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
16.3 88.34 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3021 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
18.1 79.56 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3721 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
20.1 71.64 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3721 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR5022
22 65.45 PR1021 PR1221 PR1521 PR1521 PR1721 PR1721 PR2021 PR2522 PR2722 PR3021 PR3021 PR3721 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR6021
24.6 58.54 PR1221 PR1221 PR1521 PR1521 PR1721 PR2021 PR2522 PR2722 PR2722 PR3021 PR3721 PR3721 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR6021
27.5 52.36 PR1221 PR1221 PR1521 PR1521 PR1721 PR2021 PR2522 PR2722 PR2722 PR3021 PR3721 PR3721 PR4521 PR4521 PR4521 PR5022 PR5022 PR5022 PR6021
30.7 46.91 PR1221 PR1221 PR1521 PR1521 PR1721 PR2021 PR2522 PR2722 PR3021 PR3721 PR3721 PR3721 PR4521 PR4521 PR4521 PR5022 PR5022 PR6021 PR6021
33.3 43.24 PR1221 PR1521 PR1521 PR1721 PR2021 PR2521 PR2721 PR3021 PR3521 PR3721 PR3721 PR4021 PR4521 PR4521 PR5021 PR6021 PR6021 PR6021 PR6021
41.5 34.70 PR1221 PR1521 PR1721 PR2021 PR2521 PR2521 PR3021 PR3521 PR3521 PR3721 PR4021 PR4521 PR4521 PR5021 PR6021 PR6021 PR6021 PR6021 PR6021
51.8 27.80 PR1521 PR1521 PR2021 PR2521 PR2721 PR3021 PR3521 PR3721 PR4521 PR4521 PR5021 PR5021 PR6021 PR6021 PR7021 PR7021 PR7021 PR8021 PR9021
56.6 25.44 PR1231 PR1531 PR1531 PR1731 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
63.2 22.78 PR1231 PR1531 PR1531 PR2031 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
69.9 20.60 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR7031
76.7 18.77 PR1231 PR1531 PR1731 PR2031 PR2731 PR2731 PR3031 PR3532 PR3731 PR4031 PR4031 PR4532 PR5032 PR5032 PR6031 PR7031 PR7031 PR7031 PR8031
85.5 16.84 PR1231 PR1531 PR1731 PR2031 PR2731 PR3031 PR3531 PR3731 PR3731 PR4031 PR4532 PR4532 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
93.9 15.34 PR1531 PR1531 PR2031 PR2531 PR2731 3PR031 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
95.7 15.05 PR1531 PR1531 PR2031 PR2531 PR2731 PR3031 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR5032 PR6031 PR6031 PR7031 PR7031 PR7031 PR8031
104.7 13.75 PR1531 PR1531 PR2031 PR2531 PR 2731 PR3031 PR3531 PR4031 PR4532 PR4532 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
106.7 13.50 PR1531 PR1531 PR2031 PR2531 PR2731 PR3031 PR3531 PR3731 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031
115.9 12.42 PR1531 PR1531 PR2031 PR2531 PR3031 PR3531 PR3531 PR4031 PR4532 PR4532 PR5031 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR9031
117.16 12.29 PR1531 PR1531 PR2031 PR2531 PR2731 PR3031 PR3532 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
127.2 11.32 PR1531 PR1731 PR2531 PR2731 PR3031 PR3531 PR3531 PR4031 PR4532 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
130.66 11.02 PR1531 PR1731 PR2531 PR2731 PR2731 PR3531 PR3731 PR4531 PR4532 PR5031 PR5031 PR6031 PR6031 PR6031 PR7031 PR8031 PR8031 PR9031 PR9031
141.8 10.16 PR1531 PR1731 PR2531 PR2731 PR3031 PR3531 PR3731 PR4531 PR4532 PR5031 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR10031
144.57 9.96 PR1531 PR1731 PR2531 PR3031 PR3531 PR3531 PR4031 PR4531 PR4532 PR5031 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031
158.7 9.07 PR1531 PR1731 PR2531 PR3031 PR3531 PR3531 PR4031 PR4531 PR4532 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR10031
177 8.14 PR1531 PR2031 PR2731 PR3031 PR3531 PR3531 PR4031 PR4531 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031
192.1 7.50 PR1731 PR2531 PR2731 PR3531 PR3531 PR4031 PR4531 PR5031 PR6031 PR6031 PR6031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031 PR10031 PR12031
198 7.27 PR1531 PR2031 PR3031 PR3531 PR3531 PR4031 PR4531 PR4532 PR6031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031
220.8 6.52 PR1731 PR2031 PR3031 PR3531 PR3531 PR4031 PR5031 PR5031 PR6031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031 PR10031
239.7 6.01 PR2031 PR2531 PR3031 PR3531 PR3731 PR4531 PR5031 PR6031 PR6031 PR7031 PR7031 PR8031 PR8031 PR9031 PR9031 PR10031 PR10031 PR12031 PR12031
299.1 4.81 PR2031 PR2731 PR3531 PR3731 PR4031 PR4531 PR5031 PR6031 PR7031 PR7031 PR7031 PR8031 PR9031 PR9031 PR10031 PR10031 PR12031 PR14031 PR14031
327 4.40 PR1741 PR2541 PR3041 PR3541 PR3542 PR4041 PR4542 PR5042 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR9041 PR10041 PR12041
359 4.01 PR1741 PR2541 PR3041 PR3541 PR3742 PR4542 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041
400 3.60 PR2041 PR2741 PR3541 PR3541 PR3742 PR4542 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR10041 PR12041 PR12041
443 3.25 PR2041 PR2741 PR3541 PR3541 PR3742 PR4542 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR10041 PR12041 PR12041
455 3.16 PR2041 PR2741 PR3541 PR3541 PR3742 PR4542 PR5041 PR6041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041
494 2.91 PR2041 PR2741 PR3541 PR3741 PR4041 PR4542 PR5041 PR6041 PR7041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041
503 2.86 PR2041 PR2741 PR3541 PR3741 PR4041 PR4542 PR5041 PR7041 PR7041 PR7041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041
552 2.61 PR2541 PR2741 PR3541 PR3741 PR4041 PR4542 PR6041 PR7041 PR7041 PR7041 PR8041 PR8041 PR9041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041
604 2.38 PR2541 PR3041 PR3741 PR4041 PR4542 PR5041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
689 2.09 PR2541 PR3041 PR3541 PR4041 PR4542 PR5041 PR6041 PR7041 PR7041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
734 1.96 PR2541 PR3541 PR3741 PR4541 PR4542 PR5041 PR6041 PR7041 PR9041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041
754 1.91 PR2741 PR3541 PR3741 PR4541 PR5041 PR6041 PR6041 PR7041 PR9041 PR8041 PR8041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041
769 1.87 PR2541 PR3041 PR3741 PR4541 PR4542 PR5041 PR6041 PR7041 PR9041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041
818 1.76 PR2741 PR3541 PR4041 PR4541 PR5041 PR6041 PR7041 PR7041 PR9041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR14041 PR16041
844 1.71 PR2741 PR3541 PR3741 PR4541 PR5041 PR6041 PR6041 PR7041 PR9041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041
916 1.57 PR3041 PR3541 PR4041 PR4541 PR5041 PR6041 PR7041 PR7041 PR9041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR14041 PR16041
1021 1.41 PR3041 PR3541 PR4541 PR5041 PR5041 PR6041 PR7041 PR8041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR14041 PR16041 *
1041 1.38 PR3041 PR3541 PR4541 PR4542 PR5041 PR6041 PR7041 PR8041 PR9041 PR9041 PR9041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041
1108 1.30 PR3541 PR4041 PR5041 PR6041 PR6041 PR7041 PR8041 PR8041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * *
1274 1.13 PR3041 PR3741 PR4541 PR5041 PR6041 PR6041 PR8041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 *
1383 1.04 PR3541 PR4041 PR5041 PR6041 PR6041 PR7041 PR8041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * * *
1590 0.91 PR3541 PR4041 PR5041 PR6041 PR6041 PR7041 PR8041 PR9041 PR10041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * *
1726 0.83 PR3541 PR4541 PR6041 PR6041 PR7041 PR8041 PR9041 PR10041 PR12041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * * * *
2154 0.67 PR3741 PR4541 PR6041 PR7041 PR7041 PR8041 PR10041 PR10041 PR12041 PR12041 PR14041 PR14041 PR16041 PR16041 * * * * *

10
 ØA
Lh Lf
J

Ød
ØD
ØD
H

h
L1 L2

C
L1
ØS
K
ØS

F G E G
E
N
M M
Note : All the dimension are in mm.
FOOT MOUNTING DIMENSIONS
SINGLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR1011 19 21.5 6 30 14 16 5 18 60 80 100 9 10 44 85 125 90 154 140 63
PR1211 24 27 8 35 14 16 5 18 90 100 120 14 12 64 120 150 120 174 160 63-71
PR1511 28 31 8 40 28 31 8 40 90 100 120 14 12 64 120 150 135 265 245 80-90
PR1711 38 41 10 55 28 31 8 40 90 100 140 14 15 71 120 170 150 285 265 90-100
PR2011 42 45 12 62 28 31 8 40 100 110 160 14 15 82 140 190 165 298 278 112
PR2511 50 53.5 14 75 38 41 10 50 110 120 180 14 15 97 150 220 200 347 327 132
PR2711 60 64 18 82 50 54 14 70 130 130 210 18 18 107 170 260 220 406 367 132
PR3011 65 69 18 90 50 54 14 70 150 140 210 18 20 117 200 260 250 447 408 160
DOUBLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR1021 19 21.5 6 30 14 16 5 18 60 80 100 9 10 44 85 125 90 171 157 63
PR1221 24 27 8 35 14 16 5 18 90 100 120 14 12 64 120 150 120 190 176 63-71
PR1521 28 31 8 40 28 31 8 40 90 100 120 14 12 64 120 150 135 312 292 63-90
PR1721 38 41 10 55 28 31 8 40 90 100 140 14 15 71 120 170 150 333 313 71-100
PR2021 42 45 12 62 28 31 8 40 100 110 160 14 15 82 140 190 165 349 329 80-112
PR2521 50 53.5 14 75 28 31 8 40 110 120 180 14 15 97 150 220 200 367 347 90-100
112-
PR2522 50 53.5 14 75 38 41 10 50 110 120 180 14 15 97 150 220 200 398 378 132
PR2721 60 64 18 82 28 31 8 40 130 130 210 18 18 107 170 260 220 412 392 90-112
PR2722 60 64 18 82 50 54 14 70 130 130 210 18 18 107 170 260 220 465 426 132
PR3021 65 69 18 90 50 54 14 70 150 140 210 18 20 17 200 260 250 512 473 90-112
TRIPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR1031 19 21.5 6 30 14 16 5 18 60 80 100 9 10 44 85 125 90 187 173 63
PR1231 24 27 8 35 14 16 5 18 90 100 120 14 12 64 120 150 120 216 202 63-71
PR1531 28 31 8 40 28 31 8 40 90 100 120 14 12 64 120 150 135 359 339 80-90
PR1731 38 41 10 55 28 31 8 40 90 100 140 14 15 71 120 170 150 380 360 63-90
PR2031 42 45 12 62 28 31 8 40 100 110 160 14 15 82 140 190 165 393 373 63-90
PR2531 50 53.5 14 75 28 31 8 40 110 120 180 14 15 97 150 220 200 415 395 71-100
PR2731 60 64 18 82 28 31 8 40 130 130 210 18 18 107 170 260 220 457 437 63-100
PR3031 65 69 18 90 28 31 8 40 150 140 210 18 20 117 200 260 250 476 456 71-112
QUADRUPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR1041 19 21.5 6 30 14 16 5 18 60 80 100 9 10 44 85 125 90 205 191 63
PR1241 24 27 8 35 14 16 5 18 90 100 120 14 12 64 120 150 120 243 226 63
PR1541 28 31 8 40 28 31 8 40 90 100 120 14 12 64 120 150 135 406 386 63
PR1741 38 41 10 55 28 31 8 40 90 100 140 14 15 71 120 170 150 428 408 63-71
PR2041 42 45 12 62 28 31 8 40 100 110 160 14 15 82 140 190 165 440 420 63-71
PR2541 50 53.5 14 75 28 31 8 40 110 120 180 14 15 97 150 220 200 462 442 63-80
PR2741 60 69 18 82 28 31 8 40 130 130 210 18 18 107 170 260 220 504 484 63-90
PR3041 65 69 18 90 28 31 8 40 150 140 210 18 20 117 200 260 250 520 500 63-90

11
 ØA
Lh Lf
J

Ød
ØD
ØD
H

h
C L1 L2
L1
ØS
K

ØS

F G E G
E
N
M M

Note : All the dimension are in mm.

FOOT MOUNTING DIMENSIONS
SINGLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR3511 80 85.5 22 110 50 53.5 14 70 200 160 300 18 25 137 250 350 --- 530 491 ----
PR3711 85 90.5 22 120 50 53.5 14 70 250 180 300 22 25 147 300 370 --- 548 509 ----
PR4011 95 100 25 135 50 53.5 14 70 250 200 350 22 25 162 300 400 --- 586 547 ----
PR4511 110 116 28 170 70 75 20 100 250 200 350 22 25 197 300 400 --- 693 624 ----
PR5011 120 127 32 180 70 75 20 100 300 250 400 26 30 213 360 460 --- 732 663 ----
DOUBLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR3521 80 85.5 22 110 50 53.5 14 70 200 160 300 18 25 137 250 350 --- 567 528 112-132
PR3721 85 90.5 22 120 50 53.5 14 70 250 180 300 22 25 147 300 370 --- 619 580 160
PR4021 95 100 25 135 50 53.5 14 70 250 200 350 22 25 162 300 400 --- 657 618 132-160
PR4521 110 116 28 170 50 53.5 14 70 250 200 350 22 25 197 300 400 --- 726 687 132-160
PR5021 120 127 32 180 50 53.5 14 70 300 250 400 26 30 213 360 460 --- 773 734 160-200
PR5022 120 127 32 180 70 75 20 100 300 250 400 26 30 213 360 460 839 770 200-225
TRIPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR3531 80 85.5 22 105 28 31 8 40 200 160 300 18 25 137 250 350 --- 573 553 80-112
PR3532 80 85.5 22 105 38 41 10 50 200 160 300 18 25 137 250 350 --- 593 573 132
PR3731 85 90.5 22 120 50 53.5 14 70 250 180 300 22 25 147 300 370 644 605 80-132
PR4031 95 100 25 135 50 53.5 14 70 250 200 350 22 25 162 300 400 --- 722 683 90-160
PR4531 110 116 28 170 38 41 10 50 250 200 350 22 25 197 300 400 --- 738 718 90-132
PR4532 110 116 28 170 50 53.5 14 70 250 200 350 22 25 197 300 400 --- 802 763 132-160
PR5031 120 127 32 180 50 53.5 14 70 300 250 400 26 30 213 360 460 --- 844 805 132-160
PR5032 120 127 32 180 50 53.5 14 70 300 250 400 26 30 213 360 460 --- 853 814 ---
QUADRUPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
PR3541 80 85.5 22 110 28 31 8 40 200 160 300 18 25 137 250 350 290 621 601 63-90
PR3542 80 85.5 22 110 28 31 8 40 200 160 300 18 25 137 250 350 290 613 593 90-100
PR3741 85 90.5 22 120 28 31 8 40 250 180 300 22 25 147 300 370 310 639 619 63-90
PR3742 85 90.5 22 120 28 31 8 40 250 180 300 22 25 147 300 370 310 647 627 90-100
PR4041 95 100 25 135 28 31 8 40 250 200 350 22 25 162 300 400 330 700 680 71-112
PR4541 110 116 28 170 28 31 8 40 250 200 350 22 25 197 300 400 355 758 738 80-100
PR4542 110 116 28 170 28 31 8 40 250 200 350 22 25 197 300 400 355 780 760 90-112
PR5041 120 127 32 180 28 31 8 40 300 250 400 26 30 213 360 460 400 822 802 80-112
PR5042 120 127 32 180 50 53.5 14 70 300 250 400 26 30 213 360 460 400 909 870 132-160

12
 ØA
Lh Lf
J

Ød
ØD
ØD
H

h
L1 L2
C

L1
ØS
K

ØS

F G E G
E
N
M M
Note : All the dimension are in mm.

FOOT MOUNTING DIMENSIONS

DOUBLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
180-
PR6021 150 158 36 200 70 74.5 20 100 325 300 430 33 40 270 410 530 490 892 831 200
180-
PR7021 165 174 40 220 70 74.5 20 100 350 340 490 33 40 290 440 590 560 960 895 200
200-
PR8021 180 190 45 250 70 74.5 20 100 380 375 540 33 40 340 460 650 630 1060 995 250
200-
PR9021 195 205 45 270 110 116 28 170 440 410 600 39 50 350 540 730 700 1220 1080 250
TRIPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
132-
PR6031 150 158 36 200 50 53.5 14 70 325 300 430 33 40 270 410 530 490 960 910 180
160-
PR7031 165 174 40 220 50 53.5 14 70 350 340 490 33 40 290 440 590 560 1020 970 200
160-
PR8031 180 190 45 250 50 53.5 14 70 380 375 540 33 40 340 460 650 630 1130 1080 200
160-
PR9031 195 205 45 270 70 74.5 20 100 440 410 600 39 50 350 540 730 700 1225 1150 200
180-
PR10031 220 231 50 300 70 74.5 20 100 525 450 685 39 50 385 620 820 800 1325 1250 200
200-
PR12031 260 273 56 350 110 116 28 170 590 550 800 45 50 455 700 950 925 1670 1530 250
QUADRUPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E C F S K G M N A Lf Lh Frame
100-
PR6041 150 158 36 200 50 53.5 14 70 325 300 430 33 40 270 410 530 490 1020 970 160
112-
PR7041 165 174 40 220 50 53.5 14 70 350 340 490 33 40 290 440 590 560 1120 1070 180
112-
PR8041 180 190 45 250 50 53.5 14 70 380 375 540 33 40 340 460 650 630 1200 1150 180
132-
PR9041 195 205 45 270 50 53.5 14 70 440 410 600 39 50 350 540 730 700 1280 1230 180
132-
PR10041 220 231 50 300 50 53.5 14 70 525 450 685 39 50 385 620 820 800 1380 1330 180
180-
PR12041 260 273 56 350 50 53.5 14 70 590 550 800 45 50 455 700 950 925 1660 1610 200
200-
PR14041 300 314 70 400 70 74.5 20 100 710 600 950 45 50 540 820 1150 1100 2050 1980 250
225-
PR16041 350 365 80 450 70 74.5 20 100 760 650 1075 45 50 600 870 1250 1200 2350 2250 250

13
 ØD
ØD

Ød
H

ØA
h
ØM
ØM
ØE

ØA
ØF

ØE

ØF
L2
L1 L1

G K G K
Lf
LH
Note : All the dimension are in mm.

FLANGE MOUNTING DIMENSIONS

SINGLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame
PR1011 19 21.5 6 30 14 16 5 18 90 60 5.5 10 34 75 4 90 154 140 63
PR1211 24 27 8 35 14 16 5 18 120 80 6.5 10 40 105 8 120 174 160 63-71
PR1511 28 31 8 40 28 31 8 40 135 80 8.5 10 45 115 8 135 265 245 80-90
PR1711 38 41 10 55 28 31 8 40 150 100 8.5 12 68 135 8 150 285 265 90-100
PR2011 42 45 12 62 28 31 8 40 165 115 11 15 76 145 8 165 298 278 112
PR2511 50 53.5 14 75 38 41 10 50 200 130 13 18 90 165 8 200 347 327 132
PR2711 60 64 18 82 50 53.5 14 70 220 160 13 15 92 190 8 220 406 367 132
PR3011 65 69 18 90 50 53.5 14 70 220 160 13 15 106 190 8 250 447 408 160
DOUBLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame
PR1021 19 21.5 6 30 14 16 5 18 90 60 5.5 10 34 75 4 90 171 157 63
PR1221 24 27 8 35 14 16 5 18 120 80 6.5 10 40 105 8 120 190 176 63-71
PR1521 28 31 8 40 28 31 8 40 135 80 8.5 10 45 115 8 135 312 292 63-90
PR1721 38 41 10 55 28 31 8 40 150 100 8.5 12 68 135 8 150 333 313 71-100
PR2021 42 45 12 62 28 31 8 40 165 115 11 15 76 145 8 165 349 329 80-112
PR2521 50 53.5 14 75 28 31 8 40 200 130 13 18 90 165 8 200 367 347 90-100
PR2522 50 53.5 14 75 38 41 10 50 200 130 13 18 90 165 8 200 398 378 112-132
PR2721 60 64 18 82 28 31 8 40 220 160 13 15 92 190 8 220 412 392 90-112
PR2722 60 64 18 82 50 53.5 14 70 220 160 13 15 92 190 8 220 465 426 132
PR3021 65 69 18 90 50 53.5 14 70 220 160 13 15 106 190 8 250 512 473 90-112
TRIPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame
PR1031 19 21.5 6 30 14 16 5 18 90 60 5.5 10 34 75 4 90 187 173 63
PR1231 24 27 8 35 14 16 5 18 120 80 6.5 10 40 105 8 120 216 202 63-71
PR1531 28 31 8 40 28 31 8 40 135 80 8.5 10 45 115 8 135 359 339 80-90
PR1731 38 41 10 55 28 31 8 40 150 100 8.5 12 68 135 8 150 380 360 63-90
PR2031 42 45 12 62 28 31 8 40 165 115 11 15 76 145 8 165 393 373 63-90
PR2531 50 53.5 14 75 28 31 8 40 200 130 13 18 90 165 8 200 415 395 71-100
PR2731 60 64 18 82 28 31 8 40 220 160 13 15 92 190 8 220 457 437 63-100
PR3031 65 69 18 90 28 31 8 40 220 160 13 15 106 190 8 250 476 456 71-112
QUADRUPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor*
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame
PR1041 19 21.5 6 30 14 16 5 18 90 60 5.5 10 34 75 4 90 205 191 63
PR1241 24 27 8 35 14 16 5 18 120 80 6.5 10 40 105 8 120 243 226 63
PR1541 28 31 8 40 28 31 8 40 135 80 8.5 10 45 115 8 135 406 386 63
PR1741 38 41 10 55 28 31 8 40 150 100 8.5 12 68 135 8 150 428 408 63-71
PR2041 42 45 12 62 28 31 8 40 165 115 11 15 76 145 8 165 440 420 63-71
PR2541 50 53.5 14 75 28 31 8 40 200 130 13 18 90 165 8 200 462 442 63-80
PR2741 60 69 18 82 28 31 8 40 220 160 13 15 92 190 8 220 504 484 63-90
PR3041 65 69 18 90 28 31 8 40 220 160 13 15 106 190 8 250 520 500 63-90
14
 ØD

ØD

Ød
ØF

ØM
ØE
ØM

ØF
ØE

ØA
H

h
L2
L1 L1

G K
G K
LH Lf
Note : All the dimension are in mm.
FLANGE MOUNTING DIMENSIONS
SINGLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame

PR3511 80 85.5 22 110 50 53.5 14 70 290 240 13 85 262 265 12 --- 530 491 ----
PR3711 85 90.5 22 120 50 53.5 14 70 310 250 17 90 275 285 12 --- 548 509 ----
PR4011 95 100 25 135 50 53.5 14 70 330 270 17 95 310 300 12 --- 586 547 ----
PR4511 110 116 28 170 70 75 20 100 355 290 17 110 360 325 12 --- 693 624 ----
PR5011 120 127 32 180 70 75 20 100 400 335 17 120 385 360 12 --- 732 663 ----
DOUBLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame
112-
PR3521 80 85.5 22 110 50 53.5 14 70 290 240 13 85 262 265 12 --- 567 528 132
PR3721 85 90.5 22 120 50 53.5 14 70 310 250 17 90 275 285 12 --- 619 580 160
132-
PR4021 95 100 25 135 50 53.5 14 70 330 270 17 95 310 300 12 --- 657 618 160
132-
PR4521 110 116 28 170 50 53.5 14 70 355 290 17 110 360 325 12 --- 726 687 160
160-
PR5021 120 127 32 180 50 53.5 14 70 400 335 17 120 385 360 12 --- 773 734 200
200-
PR5022 120 127 32 180 70 75 20 100 400 335 17 120 385 360 12 839 770 225
TRIPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame

PR3531 80 85.5 22 105 28 31 8 40 290 240 13 85 262 265 12 --- 573 553 80-112
PR3532 80 85.5 22 105 38 41 10 50 290 240 13 85 262 265 12 --- 593 573 132
PR3731 85 90.5 22 120 50 53.5 14 70 310 250 17 90 275 285 12 644 605 80-132
PR4031 95 100 25 135 50 53.5 14 70 330 270 17 95 310 300 12 --- 722 683 90-160
PR4531 110 116 28 170 38 41 10 50 355 290 17 110 360 325 12 --- 738 718 90-132
132-
PR4532 110 116 28 170 50 53.5 14 70 355 290 17 110 360 325 12 --- 802 763 160
132-
PR5031 120 127 32 180 50 53.5 14 70 400 335 17 120 385 360 12 --- 844 805 160
PR5032 120 127 32 180 50 53.5 14 70 400 335 17 120 385 360 12 --- 853 814 ---
QUADRUPLE STAGE
OUTPUT INPUT MOUNTING GENERAL Motor
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh Frame
PR3541 80 85.5 22 110 28 31 8 40 290 240 13 85 262 265 12 290 621 601 63-90
PR3542 80 85.5 22 110 28 31 8 40 290 240 13 85 262 265 12 290 613 593 90-100
PR3741 85 90.5 22 120 28 31 8 40 310 250 17 90 275 285 12 310 639 619 63-90
PR3742 85 90.5 22 120 28 31 8 40 310 250 17 90 275 285 12 310 647 627 90-100
PR4041 95 100 25 135 28 31 8 40 330 270 17 95 310 300 12 330 700 680 71-112
PR4541 110 116 28 170 28 31 8 40 355 290 17 110 360 325 12 355 758 738 80-100
PR4542 110 116 28 170 28 31 8 40 355 290 17 110 360 325 12 355 780 760 90-11 2
PR5041 120 127 32 180 28 31 8 40 400 335 17 120 385 360 12 400 822 802 80-112
132-
PR5042 120 127 32 180 50 53.5 14 70 400 335 17 120 385 360 12 400 909 870 160

15
 ØD

ØD

Ød
ØF

ØM
ØE
ØM

ØF
ØE

ØA
H

h
L2
L1 L1

G K
G K
LH Lf
Note : All the dimension are in mm.

FLANGE MOUNTING DIMENSIONS

DOUBLE STAGE

OUTPUT INPUT MOUNTING GENERAL

Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh

PR6021 150 158 36 200 70 74.5 20 100 490 400 21 145 340 440 24 490 892 831

PR7021 165 174 40 220 70 74.5 20 100 560 470 21 160 370 510 24 560 960 895

PR8021 180 190 45 250 70 74.5 20 100 630 540 26 180 430 580 24 630 1060 995

PR9021 195 205 45 270 110 116 28 170 700 600 26 210 435 650 24 700 1220 1080
TRIPLE STAGE
OUTPUT INPUT MOUNTING GENERAL
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh

PR6031 150 158 36 200 50 53.5 14 70 490 400 21 145 340 440 24 490 960 910

PR7031 165 174 40 220 50 53.5 14 70 560 470 21 160 370 510 24 560 1020 970

PR8031 180 190 45 250 50 53.5 14 70 630 540 26 180 430 580 24 630 1130 1080

PR9031 195 205 45 270 70 74.5 20 100 700 600 26 210 435 650 24 700 1225 1150

PR10031 220 231 50 300 70 74.5 20 100 800 675 26 240 470 735 24 800 1325 1250

PR12031 260 273 56 350 110 116 28 170 925 800 26 280 560 850 24 925 1670 1530
QUADRUPLE STAGE
OUTPUT INPUT MOUNTING GENERAL
Model
Dj6 H Jp9 L1 dj6 h jp9 L2 E F S K G M N A Lf Lh

PR6041 150 158 36 200 50 53.5 14 70 490 400 21 145 340 440 24 490 1020 970

PR7041 165 174 40 220 50 53.5 14 70 560 470 21 160 370 510 24 560 1120 1070

PR8041 180 190 45 250 50 53.5 14 70 630 540 26 180 430 580 24 630 1200 1150

PR9041 195 205 45 270 50 53.5 14 70 700 600 26 210 435 650 24 700 1280 1230

PR10041 220 231 50 300 50 53.5 14 70 800 675 26 240 470 735 24 800 1380 1330

PR12041 260 273 56 350 50 53.5 14 70 925 800 26 280 560 850 24 925 1660 1610

PR14041 300 314 70 400 70 74.5 20 100 1100 950 26 320 680 1000 24 1100 2050 1980

PR16041 350 365 80 450 70 74.5 20 100 1200 1075 26 360 750 1125 24 1200 2350 2250

16
Spline Data (Internal)
E MODEL AH8 BH8 C D E SPLINEDATA
C D
PR2511 42 30 30 40 5 A 40 x 35 IS:3665-1966
PR2711 46 35 35 45 5 A 45 x 40 IS:3665-1966
Splines
PR3011 55 40 45 55 5 A 50 x 45 IS:3665-1966
PR3511 60 50 55 65 5 A 58 x 53 IS:3665-1966
PR3711 65 55 60 70 5 A 63 x 54 IS:3665-1966
PR4011 70 60 65 80 9 A 68 x 63 IS:3665-1966
ØB
ØA

PR4511 85 70 80 100 10 A 80 x 75 IS:3665-1966

PR5011 95 80 85 105 10 A 90 x 85 IS:3665-1966
N 120 x 5 x
PR6011 125 100 90 110 10 DIN 5480
9H
N 130 x 5 x
PR7011 135 110 95 115 10 DIN 5480
9H
REF LINE N 140 x 5 x
PR8011 145 125 100 125 10 DIN 5480
9H
N 150 x 5 x
PR9011 160 135 120 150 10 DIN 5480
9H
N 170 x 5 x
PR10011 180 150 150 175 10 DIN 5480
9H
N 200 x 5 x
PR12011 205 175 170 210 20 DIN 5480
9H
N 240 x 5 x
PR14011 245 210 190 230 20 DIN 5480
9H
N 280 x 5 x
PR16011 285 250 230 270 20 DIN 5480
9H

Spline Data (External)

3 HOLES AT 120° MODEL A f8 B f7 C D E F GXH SPLINE DATA
G

IS:3665-
PR2511 50 40 25 25 5 50 M8 X 15 B 48 X 43
1966
ØC
ØB
ØA

IS:3665-
PR2711 55 45 28 28 5 55 M8 X 15 B 53 x 48
1966
C E
IS:3665-
F PR3011 60 50 35 35 5 60 M8 X 15 A 58 x 53
1966

REF. LINE IS:3665-

PR3511 70 60 40 40 5 70 M10 X 25 B 68 x 63
1966

IS:3665-
PR3711 75 60 40 40 5 75 M8 X 15 B 72 X 67
1966

IS:3665-
PR4011 80 65 45 45 5 80 M10 X 25 B 75 X 70
1966

IS:3665-
PR4511 85 70 45 50 10 90 M10 X 25 B 80 X 75
1966

IS:3665-
PR5011 100 90 70 70 10 110 M12 X 30 B 98 X 93
1966
W 140 X 5
PR6011 145 125 100 95 10 150 M16 X 30 DIN 5480
X 8F

PR7011 160 130 110 105 10 160 M8 X 15

W 150 X 5 DIN 5480
X 8F

W 170 X 5
PR8011 170 145 120 115 15 180 M16 X 30 DIN 5480
X 8F

W 190 X 5
PR9011 190 160 130 125 15 190 M8 X 15 DIN 5480
X 8F

W 200 X 5
PR10011 210 180 150 150 20 230 M20 X 35 DIN 5480
X 38

W 250 X 8
PR12011 260 225 190 200 20 300 M20 X 35 DIN 5480
X 30

W 280 X 8
PR14011 290 250 120 225 20 325 M20 X 35 DIN 5480
X 34

W 320 X 8
PR16011 325 290 250 250 20 360 M24 X 45 DIN 5480
X 38
17
 Shrink Disc / Torque Arm Details
L3
A

ØH
ØD
Lmin

L
L1

Ød

T G

All Dimensions in mm

TORQUE ARM
MODEL OUTPUT SHAFT SHRINK DISC DETAILS
L
D dw d1 L L1 H L3 A min d T G
50
PR3011 68 55 45 60 70 115 35 31 150 18 12 56
60
60
PR3511 80 65 55 65 75 145 38 33 200 20 16 197
70
65
PR4011 90 70 60 70 80 155 45 39 200 20 16 225
75
75
PR4511 110 80 70 75 85 185 57 50 250 24 20 250
85
85
PR5011 125 90 80 90 100 215 61 54 300 24 20 270
95
95
PR6011 140 100 90 100 110 230 69 61 350 28 25 270
105
125
PR8011 175 130 120 130 140 300 81 71 425 28 32 320
135
160
PR10011 220 165 150 160 170 370 114 104 500 32 32 350
170
190
PR12011 260 200 1820 200 215 430 133 120 575 38 32 394
210
230
PR10411 300 240 220 240 260 485 155 142 650 42 50 476
245
270
PR16011 350 280 260 280 300 580 175 162 700 48 50 525
285

18
 PLANETARY DRIVES

Rating : Up to 1500000 Nm

Ratio : Up to 25000/1

Mounting : Foot, Flange & Shaft Mounted

Application : Industrial Sectors - Sugar, Steel,

Paper, Cement, Chemical,
Construction.
Mounting : shaft mounted Mounting : Flange Mounting : Foot .

SPECIAL APPLICATIONS

SUGAR MILL DRIVE WINCH DRIVE WITH HYDRAULIC BRAKE

TRANSIT MIXER DRIVE WHEEL / FINAL DRIVE

WITH HYDRAULIC BRAKE

BEVEL MIXER DRIVE SLEW DRIVE WITH

HYDRAULIC BRAKE

19
 Variable Speed Fluid Coupling Geared Motor

Helical Gearbox Cooling Tower Gearbox

Premium Transmission Limited

Head Office : Premium House, Mumbai-Pune Road, Chinchwad, Pune - 411019, India.
Tel. : (91-20) 27488886 / 27488947, Fax : (91-20) 27450287 / 27472384
Website : www.premiumtransmission.com

Manufacturing Units : Unit-I : Old Mumbai - Pune Road, Chinchwad, Pune - 411 019, India. Tel. : 91-20- 66314100 Fax : 91-20- 27450287,
27472384. Unit-II : Falta Industrial Growth Centre, Sector-III, Falta, 24 Parganas (South), West Bengal 743504, India. Tel.: 91-3174-222231 / 32
/ 33 / 37, Fax : 91-31749 222234. Unit-III : G-56 / 57, MIDC Industrial Area, Chilkalthana, Aurangabad - 431 210, India. Tel.: 91-240-2485521,
2485856, 2485056, Fax : 91-240-2485756. Unit-IV : 31-P, MIDC Industrial Area, Chilkalthana, Aurangabad - 431 210, India. Tel.: 91-240-
2482858, 2471298, Fax : 91-240-2482857.

Regional Offices : Mumbai : Corporate Park II, 4th Floor, Sion, Trombay Road, Chembur, Mumbai - 400071, India. Tel.: 91-22-25264750,
25264763, Fax : 91-22-25262622, 25264800. New Delhi : Express Building Annexe, 9-10, Bahadhur Shah Zafar Marg, New Delhi - 110 002,
India. Tel. : 91-11-23730554 (8 Lines), Fax : 91-11-23359782 / 23357739. Kolkata : Thapar House, 25, Brabourne Road, Kolkata - 700 001,
India. Tel.: 91-33-22424316, 22423780, 22423805, 22424317 / 20 / 21, 22438815, 22420817, Fax : 91-33-22424325. Chennai : "Wavoo
Mansion", 7th Floor, New No. 48 (Old No. 39) Rajaji Salai, Chennai - 600 001, India. Tel.: 91-44-25255200, 91-44-25224557. Nagpur : Plot No
15, State Bank Colony, Ujjwal Nagar, Somalwada, Wardha Road, Nagpur - 25. Mobile : (0) 9425009827
pratisaad.com 11/2009/14796

Branch Offices : Ahmedabad : ‘Jaldarshan' Ashram Road, Navrangpura, Ahmedabad - 380 009, India. Tel.: 91-79-26580428 / 0518 / 1856 /
1857 / 1861, Fax : 91-79-26587783. Bangalore : 16/3, Ali Asker Road, Off Cunningham Road, Bangalore - 560 052, India. Tel.: 91-80-
22262062, Fax : 91-80-22253472. Hyderabad : 6-2-47, A, C. Guards, 1st Floor, Hyderabad - 500 004, India. Tel.: 91-40-23314025, 23316446,
23390544, Fax : 91-40-23318557. Kochi : 39/5567, M. G. Road, Emakulam, Kochi - 682 015, India. Tel.: 91-484-2359661, 2359372, 2359190,
Fax : 91 484-2359589.

Representative Offices : Lucknow : G-901, Halwasiya Utsav Enclave, Opposite HAL, Faizabad Road, Lucknow - 226 016, India. Tel.: 91-
522-4001344, Mobile : (0) 9793581144. Mohali : House No. 33, 1st Floor, Phase - XI, Sas Nagar (Mohali), Punjab - 160 062, Tel.: 91-172-
2230633, Mobile : (0) 9814640863. Jamshedpur : Flat No. 61 A, First Floor, Rajendranagar Colony, Sakchi, Jamshedpur 831001, Jharkhand.
Mobile : (0) 9771844408. Rourkela : A/72, Sector - 13, Rourkela - 769009. Orissa. Mobile : (0) 9437122066. Jaipur : B-1A, Vivekanand Colony,
Naya Kheda Near Ambabari, Jaipur - 302012, Rajasthan. Mobile : (0) 9887720845. Coimbatore : Door no. 55, Rangsamy Layout, Pellamedu,
Coimbatore - 641004. Mobile : (0) 9894295769. Baroda : B 24, Deep Darshan 1 Society, Ataladra, Padra Road, Baroda, Gujarat. Mobile : (0)
PETL/PG/801

9375122012. Raipur : A-10, Shubham Vihar, Behind Anmol Super Market, New Puraina, Mahavir Nagar, Raipur - 492 001 Chhatisgarh, Mobile :
(0) 9826903132. Indore : C-6, Shreevardhan Complex, 4, RNT Marg., Indore - 452001. Ph : 0731-2510943. Mobile : (0) 9302690943.
Vishakhapattnam : Flat No. 101, Yadu Residency, Rednum Garden, Ramnagar, Vishakhapattnam-530002, Mobile : (0) 9866167594.