Scribd
Upload
56 views

MMS50C

This document provides product details for an MMS50C hydraulic motor. It has a displacement of 50 cm3/rev and side ports. Key features include a maximum speed of 400 RPM, maximum torque of 4.5 daNm, and maximum pressure drop of 70 bar. Dimensional drawings and performance diagrams are included.

Uploaded by

Claudio Sa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
56 views

MMS50C

This document provides product details for an MMS50C hydraulic motor. It has a displacement of 50 cm3/rev and side ports. Key features include a maximum speed of 400 RPM, maximum torque of 4.5 daNm, and maximum pressure drop of 70 bar. Dimensional drawings and performance diagrams are included.

Uploaded by

Claudio Sa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

MMS50C

PRODUCT FEATURE SUMMARY


DATE: 19.08.2020 Username: Wolfgang Löwentraut
MODEL TYPE: MMS50C

CNSORDERNO (Bestellnummer) MMS50C


AO (Einstellung Option) weglassen: ohne Ventil
MF (Befestigungsflansch) weglassen: Drei Schrauben montieren
PT (Port-Typ) S: Side-Ports
DC (Displacement-Code) 50: 50,0 cm³/rev [3.05 in³/rev]
SE (Wellen Extensions) C: ø16 gerade, Passfeder A5x5x16 DIN6885
P (Ports) weglassen: BSPP (ISO 228)
LC (Linie zu steuern) -
VPR (Ventilnenndruckbar) -
SFMS (Besonderheiten Measure Geschwindigkeit) weglassen: keine Besonderheiten
SFGWS (Besonderheiten bei der Zahnrad-Set) weglassen: keine Besonderheiten
SFDR (Besondere Merkmale - Drehrichtung) weglassen: Standard
OP (Option (Farbe)) weglassen: keine Farbe
INFO (Info) PDF catalog
L (mm) 122.5
L1 (mm) 21

DATA SHEET
Type Type

Displacement, cm3/rev [in3/rev] 50[3.05] cont. 140 [2030]

cont. 400 Max. Inlet Pressure,


Max. Speed, Int.* 175 [2540]
bar [PSI]
[RPM]
Int.* 500
peak** 225 [3260]
cont. 4,5 [398]
Max. Torque, cont. 140 [2030]
daNm [lb-in] Max. Return Pressure
Int.* 5,8 [513]
with Drain Line Int.* 175 [2540]
cont. 1,7 [2.48] bar [PSI]
Max. Output,
peak** 225 [3260]
kW [HP]
Int.* 2,1 [2.8]
Pressure with Unloaded Shaft, bar [PSI] 4 [60]
cont. 70 [1015]
Max. Pressure Drop, at max. press. drop cont. 3,7 [330]
Min Starting Torque,
bar [PSI]
Int.* 90 [1300] daNm [lb-in]
at max. press. drop Int.* 4,8 [425]
cont. 20 [5.5]
Max. Oil Flow, Min. Speed***, [RPM] 20
lpm [GPM]
Int.* 25 [6.6] Weight, kg [lb] 2,5 [5.51]

* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.

1. Intermittent speed and intermittent pressure drop must not occur simutaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm²/s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

page 1/6
MMS50C
3d generated view

To see model in 3D you should use Acrobat Reader with enable 3D view

page 2/6
NOTE: Showed dimensions are in nominal, for maximal values see table. L max LS max
NOTE: For additional dimensions and information about flange , shaft , endcover , etc. see next
page. 122.5

MMS50C

19.08.2020 2,5 [5.51]

page 3/6
omit: Three bolts mount

S: Side ports

C: ø16 straight, Parallel key A5x5x16 DIN6885

MMS50C

19.08.2020 2,5 [5.51]

page 4/6
MMS50C

Hydraulic scheme with check valves

FUNCTION DIAGRAMS

The function diagrams data is for average performance of randomly selected motors at back pressure
5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122°F].

page 5/6
MMS50C
DATA SHEET
Pressure Losses

PERMISSIBLE SHAFT LOADS

The chart shows the permissible radial load when L=20 mm


[.79 in]. If the calculated shaft load exceeds the permissible one,
a falexible coupling must be used.

M+S Hydraulic , address - 68, Kozloduy street, 6100 Kazanlak, Bulgaria


Tel.: ++359 431 65167, ++359 431 64271, FAX: +359 431 64114
E-Mail: [email protected] : URL: http://www.ms-hydraulic.com

page 6/6

You might also like