Republic of the Philippines

Department of Education
REGION III
SCHOOLS DIVISION OF CABANATUAN CITY
IMELDA INTEGRATED SCHOOL

SUMMATIVE TEST IN ELECTRICAL INSTALLATION AND MAINTENANCE 8

Multiple Choice.
Directions: Read the statement carefully and identify what is being described or defined. Write the letter
of the correct answer on your answer sheet.

1. This is used for griping, holding, cutting electrical wires and cables and even small nails. Usually used
by linemen in doing heavy tasks.
a. Hammer c. Combination Pliers
b. Wire Stripper d. Philips Screw Driver
2. Used for cutting and holding fine wires. This can reach tight space or small opening where other pliers
cannot reach and also used in making terminal loops of copper wires.
a. Hammer c. Flat Screw Driver
b. Long Nose Pliers d. Allen Screw Driver
3. This has a cross tip resembling a positive (+) sign. It is used to drive screws with cross slot heads.
a. Hacksaw c. Electrician’s Knife
b. Wire Stripper d. Philips Screw Driver
4. This tool is used in driving, pounding and pulling out nails.
a. Hammers c. Combination Pliers
b. Wire Stripper d. Philips Screw Driver
5. A tool used for removing insulation of medium sized wires ranging from gauge #10 to gauge #16
a. Hacksaw c. Electrician’s Knife
b. Wire Stripper d. Philips Screw Driver
6. A small drilling machine with a chuck capacity of ¼” to 3/8”. It is used in making holes on metal sheets
and concrete walls.
a. Long Nose Pliers c. Stubby Screw Driver
b. Electrician’s Knife d. Portable Electric Drill
7. It comes in either standard or Philips screw drive with short shank or blade and shorted handle used
to turn screws in tight space where standard screw driver cannot be used.
a. Long Nose Pliers c. Stubby Screw Driver
b. Electrician’s Knife d. Portable Electric Drill
8. It is used by linemen to remove insulation of wire and cables in low and high voltage transmission
lines.
a. Hacksaw c. Long Nose Pliers
b. Electrician’s Knife d. Philips Screw Driver
9. It is a device inserted to a convenience outlet to conduct electric current. A flat cord is attached to it on
one end and the other end is connected to a current consuming instrument or appliance.
a. Fuse c. Male Plug
b. Switch d. Lamp Holders
10. This is a circuit protective device that automatically blows and cut the current when an overload or
short circuit happens.
a. Fuse c. Male Plug
b. Switch d. Lamp Holders
11. This is a rectangular shaped metallic or plastic (PVC) material in which flush type convenience outlet
and switched are attached.
a. Clamps c. Flat Cord
b. Conduits d. Utility Box
12. They are electrical materials used as the passage of wires for protection and insulation.
a. Clamps c. Flat Cord
b. Conduits d. Utility Box
13. They are used to attach metallic or non-metallic conduit to the junction or utility boxes.
a. Clamps c. Connectors
b. Conduits d. Junction Box
14. This is a protective device used to automatically cut off the current when trouble in the circuit such
as short circuit or overload occurs.
a. Clamps c. Junction Box
b. Connectors d. Circuit Breaker
15. It is an octagonal shaped electrical material where the connections or joints of wires are being done.
It is also where the flush type lamp holder is attached.
a. Clamps c. Junction Box
b. Connectors d. Circuit Breaker
 Republic of the Philippines
Department of Education
REGION III
SCHOOLS DIVISION OF CABANATUAN CITY
IMELDA INTEGRATED SCHOOL

16. A device that connects and disconnects the flow of electric current in a circuit.
a. Fuse c. Male Plug
b. Switch d. Lamp Holders
17. It is a duplex stranded wire used for temporary wiring installation and commonly used in extension
cord assembly.
a. Clamps c. Flat Cord
b. Conduits d. Utility Box
18. It is a device that acts as a convenient source of electrical energy for current consuming appliances.
a. Connectors c. Circuit Breaker
b. Junction Box d. Convenience Outlet
19. Devices that hold and protect the lamp and are also called as receptacles.
a. Fuse c. Male Plug
b. Switch d. Lamp Holders
20. It is an electrical material used to hold and anchor electrical conduits in its proper position.
a. Clamps c. Flat Cord
b. Conduits d. Utility Box
21. An instrument used to measure the amount of electrical current intensity in a circuit.
a. Ammeter c. Ohmmeter
b. Voltmeter d. Micrometer
22. A pocket-sized tools used to test the line wire or circuit if there is current in it.
a. Ruler c. Wire gauge
b. Test light d. Pull-push rule
23. A measuring tool used to measure the length of an object in centimeter and inches.
a. Ruler c. Wire gauge
b. Test light d. Pull-push rule
24. It is used to measure the diameter of wires/conductors in circular mils. It can measure small and big
sizes of wires and cables.
a. Ammeter c. Ohmmeter
b. Voltmeter d. Micrometer
25. It is used to measure the voltage, resistance and current of a circuit. It is connected in parallel or
series with the circuit depending on what to measure.
a. Ammeter c. Ohmmeter
b. Voltmeter d. Volt-Ohmmeter
26. An instrument used to determine the size of wires/conductors.
a. Ruler c. Wire gauge
b. Test light d. Pull-push rule
27. It is a measuring tool used to measure length, width and thickness of short flat object and in
sketching straight lines.
a. Ruler c. Wire gauge
b. Test light d. Pull-push rule
28. It is an instrument used to measure the electrical pressure or voltage of a circuit.
a. Ammeter c. Ohmmeter
b. Voltmeter d. Micrometer
29. It is also called tong-tester. It is used to measure current flowing in a conductor.
a. Ammeter c. Ohmmeter
b. Voltmeter d. Clamp Ammeter
30. It is the process or the result of determining the ratio of a physical quantity such as length, time,
temperature, etc.
a. Measurement c. Requisition Slip Form
b. Extension Cord d. Common Wire Splices
31.