UJJAIN SMART CITY LTD

COST SUMMARY FOR SWIMMING POOL PHASE-II

S.No. Description Amount (INR) Remarks

1 Civil Work ₹ 9,40,68,230

2 Electrical Work ₹ 1,54,70,065

3 Plumbing Works ₹ 77,66,681

4 ICT Component ₹ 17,04,882

5 Air Conditioner ₹ 34,57,688

6 Road Work ₹ 2,87,46,318

7 Filtration System Equipment & Accessories ₹ 1,26,59,049

Total ₹ 16,38,72,913
EXPECTED O&M EXPENDITURE
S.NO. ITEM AMOUNT Remarks

1 YEAR 1 ₹ 24,00,000

2 YEAR 2 ₹ 30,00,000

3 YEAR 3 ₹ 31,50,000

4 YEAR 4 ₹ 33,07,500

5 YEAR 5 ₹ 34,72,875
TOTAL ₹ 1,53,30,375
TOTAL COST ₹ 17,92,03,288

Page 1 of 51
 1. CIVIL WORK

Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Carriage of Material
Loading and unloading of stone boulder / stone
aggregates / sand / kanker / moorum. (Placing tipper at
1 1 loading point, loading with front end loader, dumping,
turning for return trip, excluding time for haulage and
return trip)
i For a lead upto 1 Km. Cum 73 66 300 ₹ 19,710.00
ii For a lead upto 2 Km. Cum 81 73 300 ₹ 21,870.00
iii For a lead upto 3 Km. Cum 88 79 300 ₹ 23,760.00

EARTH WORK
Earth work in Excavation by Mechanical Means
(Haydrulic Excavator) / Manual means over area
(exceeding 300mm depth,1.5 m in width or 10 Sqm on
plan) including dressing of sides and ramming of
2 2.6 bottoms lift upto 1.5 m, including getting out the
excavated soil and disposal of surplus excavated soils as
directed, within a lead of 50m.

i 2.6.1 all kind of soil Cum 127 114.30 18467.10 ₹ 21,10,790.00

Excavating trenches of required width for pipes, cables,

etc including excavation for sockets, and dressing of
sides, ramming of bottoms, depth upto 1.5 m including
getting out the excavated soil, and then returning the soil
3 2.10 as required, in layers not exceeding 20 cm in depth
including consolidating each deposited layer by
ramming, watering, etc. and disposing of surplus
excavated soil as directed, within a lead of 50 m :

Pipes, cables etc. exceeding 300 mm dia but not

2.10.3 exceeding 600 mm. Meter 226 203.40 265.00 ₹ 53,901.00

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not
4 2.25 exceeding 20cm in depth, consolidating each deposited Cum 59 53.10 8690.40 ₹ 4,61,460.00
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 mtr and more
Supplying and filling in plinth under floors including,
5 2.27 watering,
ramming consolidating and dressing complete
i 2.27.3 Moorum/Hard copra Cum 570 513.00 14116.05 ₹ 72,41,534.00

Diluting and injecting chemical emulsion for POST-

6 2.34 CONSTRUCTIONAL anti-termite treatment (excluding
the cost of chemical emulsion .
Along external wall where the apron is not provided
using chemical emulsion @ 7.5 liters / sqm of the
i 2.34.1 vertical surface of the substructure to a depth of 300
mm including excavation channel along the wall &
rodding etc. complete.
With Chlorpyriphos/ Lindane E.C. 20% with 1%
a 2.34.1.1 Meter 9 8.10 1185.00 ₹ 9,599.00
concentration.

Page 2 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Along the external wall below concrete or masonry
apron using chemical emulsion @ 2.25 litres per linear
ii 2.34.2
meter including drilling and plugging holes etc.

With Chlorpyriphos/ Lindane E.C. 20% with 1% sqm

a 2.34.2.1
concentration.

Construction of granular sub-base by providing coarse

graded material, spreading in uniform layers with on
prepared surface, mixing by mix in place method at
VOL III OMC, and compacting with vibratory roller to achieve
7
4.1 the desired density, complete in all respect and as per
relevant clauses of section-400.

a ii for grading- II Material Cum 614 552.60 549.90 ₹ 3,03,875.00

Clearing jungle including uprooting of rank vegetation,

grass, brush wood, trees and saplings of girth upto 30
cm measured at a height of1 m above ground level and 100sq
8 2.31 removal of rubbish upto a distance of 50 meter outside 341 306.90 65.00 ₹ 19,949.00
m
the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m

above ground level) including cutting of trunks and
9 2.33 branches removing the roots and stacking of serviceable
material and disposal of unserviceable material.

a 2.33.1 Beyond 30 cm girth upto and including 60 cm girth Each 104 93.60 5.00 ₹ 468.00
b 2.33.2 Beyond 60 cm girth upto and including 120 cm girth Each 466 419.40 5.00 ₹ 2,097.00

CONCRETE WORK
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
10 4.1
shuttering. All work up to plinth level.

Cement concrete grade M-10 (Nominal Mix) with 20

a 4.1.4 Cum 3595 3235.50 825.50 ₹ 26,70,905.00
mm maximum size of stone aggregate

Providing and laying in position machine batched,

machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced
cement concrete work including pumping of concrete to
site of laying but excluding the cost of centering,
shuttering, finishing and reinforcement. including
11 5.30 Admixtures in recommended proportions as per IS Cum 5211 4689.90 1071.30 ₹ 50,24,290.00
9103 to accelerate, retard setting of concrete, improve
workability without impairing strength and durability as
per direction of Engineer-in-charge. M-20 grade
reinforced cement concrete by using 405 kg. of cement
per cum of concrete. All work up to floor 2 level.

Page 3 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Providing and laying in position machine batched,
machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced
cement concrete work including pumping of concrete to
site of laying but excluding the cost of centering,
shuttering, finishing and reinforcement. including
Admixtures in recommended proportions as per IS
12 5.31 9103 to accelerate, retard setting of concrete, Cum 5245 4720.50 2984.14 ₹ 1,40,86,615.00
improve workability without impairing strength and
durability as per direction of Engineer-in-charge. M-
25 grade reinforced cement concrete by using 410
kg. of cement per cum of concrete. All work up to floor
2 level.

Reinforcement for RCC work including

straightening, cutting, bending, placing in position
13 5.2 and binding including cost of binding wire upto all
height and level including wastage etc complete

a 5.20.6 TMT (Thermo-Mechanically Treated Bars) Kg. 60 54.00 414749.05 ₹ 2,23,96,449.00

FORM WORK
Centering and shuttering including strutting, propping
14 20.1 etc. and
removal of form for :
Foundations, footings, bases of columns, etc. for
a 20.1.1 mass Sqm 138 124.20 621.60 ₹ 77,203.00
concrete up to plinth level.
Walls (any thickness) including attached pilasters
b 20.1.2 butteresses, Sqm 216 194.40 1388.00 ₹ 2,69,827.00
plinth beams and string courses etc.
Suspended floors, roofs, landings, balconies and
c 20.1.3 access Sqm 227 204.30 1185.00 ₹ 2,42,096.00
platform.
Lintels, beams, beams, girders, bressumers and
d 20.1.5 Sqm 203 182.70 2844.00 ₹ 5,19,599.00
cantilevers.
Columns, Pillars, Piers, Abutments, Posts and Struts.
e 20.1.6 Sqm 282 253.80 1386.00 ₹ 3,51,767.00
f 20.1.7 Stairs, (excluding landings) except spiral-staircases. Sqm 278 250.20 87.00 ₹ 21,767.00
g 20.1.21 Weather shade, Chajjas, corbels etc., including edges Sqm 352 316.80 35.00 ₹ 11,088.00

BRICK WORK
Brick work with modular fly ash lime bricks
(FALG Bricks) conforming to IS:12894-2002, class
15 6.27
designation 100 average compressive strength
including the cost of scaffolding :
Cement mortar 1:6 (1 cement : 6 coarse sand) for
a 6.27.2 Cum 3941 3546.90 1646.08 ₹ 58,38,482.00

MARBLE WORK

Page 4 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Providing and fixing 16mm thick gang saw cut mirror
polished premoulded and prepolished) machine cut for
kitchen platforms, vanity counters, window sills , facias
and similar locations of required size of approved shade,
colour and texture laid over 20mm thick base cement
16 8.20 mortar 1:4 (1 cement : 4 coarse sand) with joints
treated with white cement, mixed with matching
pigment, epoxy touch ups, including rubbing, curing,
moulding and polishing to edge to give high gloss finish
etc. complete at all levels.

a 8.2.8 Granite of any colour and shade

i 8.2.8.2 Area of slab over 0.50 sqm. Sqm 2544 2289.60 819.00 ₹ 18,75,182.00

Providing and fixing stone slab table rubbed, edges

rounded and polished of size 75x50 cm deep and 1.8
cm thick fixed in urinal partitions by cutting a chase
of appropriate width with chase cutter and embedding
17 8.10 the stone in the chase with epoxy grout or with
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 6 mm nominal size) as per
direction of Engineer-in- charge and finished smooth.

a 8.10.2 Granite Stone of approved shade. Sqm 2824 2541.60 45.00 ₹ 1,14,372.00

WOOD AND PVC WORK

Providing wood work in frames of doors, windows,
clerestory windows and other frames, wrought
18 9.1
framed and fixed in position :

a 9.1.1 Second class teak wood Cum 83137 74823.30 1.52 ₹ 1,14,031.00
B 9.1.2 Other then teak wood Cum 65973 59375.70 15.30 ₹ 9,08,448.00

Providing and fixing ISI marked flush door shutters

conforming to IS: 2202 (Part I) decorative type,
core of block board construction with frame of 1st
class hard wood and well matched teak 3 ply
19 9.20 veneering with vertical grains or cross bands and
face veneers on both faces of shutters using
following hinges.

35 mm thick including ISI marked Stainless Steel butt

a 9.20.1 hinges Sqm 2100 1890.00 191.52 ₹ 3,61,973.00
with Sqm 2 100.00 necessary screws.

Providing and fixing ISI marked oxidised M.S. sliding

20 9.62 door bolts
with nuts and screws etc. complete :
a 9.62.1 300x16 mm Each 105.00 94.50 115.00 ₹ 10,868.00

Providing and fixing bright finished brass tower bolts

21 9.74 (barrel
type) with necessary screws etc. complete :
a 9.74.1 250x10 mm Each 245.00 220.50 60.00 ₹ 13,230.00

Providing and fixing bright finished brass handles with

22 9.81 screws
etc. complete :
a 9.81.1 125mm Each 153.00 137.70 115.00 ₹ 15,836.00

Page 5 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction

Providing and fixing bright finished brass hanging type

23 9.82 floor Each 124.00 111.60 60.00 ₹ 6,696.00
door stopper with necessary screws, etc. complete.

Providing and fixing M.S. grills of required pattern in

24 9.48 frames of windows etc. with M.S. flats, square or round
bars etc. all complete.
Fixed to openings /wooden frames with rawl plugs
a 9.48.2 Kg 87.00 78.30 1303.00 ₹ 1,02,025.00
screws etc.

STEEL WORK
Structural steel work in single section fixed with or
without connecting plate including cutting, hoisting,
25 10.1 Kg 59 53.10 12544 ₹ 6,66,086.00
fixing in position and applying a priming coat of
approved steel primer all complete.

Structural steel work riveted, bolted or welded in

built up sections, trusses and framed work, including
26 10.2 cutting, hoisting, fixing in position and applying a Kg 62 55.80 11651 ₹ 6,50,126.00
priming coat of approved steel primer all complete:

Providing and fixing pressed steel frames for doors,

windows & ventilators confirming to IS:
4351manufactured from commercial mild steel sheet
of 1.25 mm thickness including hinges jamb, lock jamb,
bead and if required angle threshold of mild steel angle
of section 50x25mm, or base ties of 1.25mm pressed
mild steel welded or rigidly fixed together by
27 10.14 mechanical means, adjustable lugs with split end tail
to each jamb including steel butt hinges 2.5mm thick
with mortar guards, lock strike- plate and shock
absorbers as specified and applying a coat of
approved steel primer after pre-treatment of the
surface as directed by Engineer-in-charge:

a 10.14.2 Single rebate 100x50mm Meter 334 300.60 470.4 ₹ 1,41,402.00

Providing and fixing hand rail of approved size by

welding etc. to steel ladder railing, balcony railing and
28 10.26
staircase railing including applying apriming coat of
approved steel primer.
a 10.26.1 M.S. tube. Kg 84 75.60 2000.00 ₹ 1,51,200.00

Providing and fixing chicken mesh as per ISI

specification and in the required width with 50mm long
MPPWD Bombay nails on vertical and horizontal junctions of
29 sqm 62.0 55.80 495.0 ₹ 27,621.00
13.27 RCC and brick wall including scaffolding and all lead
and lift etc. complete before plastering upt 10 meter
height.

FLOORING

Page 6 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
52 mm thick cement concrete flooring with concrete
hardener topping under layer 40 mm thick cement
concrete grade M-15 (Nominal Mix with 20mm
maximum size of stone aggregate) and top layer 12 mm
thick cement hardener consisting of mix 1:2 (1 cement
hardener mix : 2 graded stone aggregate 6 mm nominal
30 11.4 size) by volume .hardening compound is mixed @ 2 Sqm 347 312.30 1668.00 ₹ 5,20,916.00
litre per 50 kg of cement or as per manufacturers
specifications. This includes cost of cement slurry, but
excluding the cost of nosing of steps etc. complete.

Extra for pre finished nosing in treads of steps of Kota

31 11.31 meter 32 28.80 45.00 ₹ 1,296.00
stone/ sandstone slab.

Providing and fixing Ist quality ceramic glazed

wall tiles conforming to IS : 15622 (6-7mm thickness)
of approved make in all colours, shades except
burgundy, bottle green, black of any size as approved by
Engineer-in-Charge in skirting, risers of steps and dados
32 11.34 over 12 mm thick bed of cement Mortar 1:3 (1 cement Sqm 686 617.40 704.00 ₹ 4,34,650.00
: 3 sand) and jointing with grey cement slurry @
3.3kg per Sqm including pointing in white cement
mixed with pigment of matching shade complete

Providing and laying Ceramic glazed floor tiles

300x300 mm (9 to 10 mm thick) of 1st quality
conforming to IS : 15622 of approved make in colours
such as White, Ivory, Grey, Fume Red Brown, laid on
33 11.35 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse Sqm 804 723.60 620.60 ₹ 4,49,066.00
sand) including pointing the joints with white cement
and matching pigment etc., complete.

Providing and laying polished vitrified floor tiles in

different sizes (thickness to be specified by the
manufacturer) with water absorption's less than
0.08% and conforming to IS : 15622 of approved
34 11.39 make in all colours and shades, laid on 20mm
thick cement mortar 1:4 (1 cement : 4 coarse sand)
including grouting the joints with white cement and
matching pigments etc., complete.

a 11.39.2 Size of Tile 60x60 cm x 10 mm Sqm 1109 998.10 424.60 ₹ 4,23,793.00

Dry stone pitching 20 to 22.5cm thick including supply
35 11.43 Sqm 783 704.70 162.00 ₹ 1,14,161.00
of stones and preparing surface complete.
Fixing glazed/ Ceramic/ Vitrified floor tiles with cement
based high polymer modified quick-set tile adhesive
36 11.41 (Water based) conforming to IS: 15477 , using 5kg. Sqm 268 241.20 233.00 ₹ 56,200.00
adhesive per sqm of tile area, in average 3mm thickness
with fixing material.
Kota stone slabs 30 mm thick in risers of steps, skirting,
dado and pillars laid on 12 mm (average) thick cement
mortar 1:3 (1 cement 3 coarse sand) and jointed
37 11.50 with grey cement slurry mixed with pigment to match sqm 901 810.90 123.00 ₹ 99,741.00
the shade of the slabs, including rubbing and polishing
complete.

Page 7 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Cement plaster skirting (up to 30 cm height) with
38 11.6 cement mortar 1:3 (1 cement : 3 coarse sand) finished
with a floating coat of neat cement.
a 11.6.1 18 mm thick. Sqm 216 194.40 66.00 ₹ 12,830.00

Providing and laying Endura Swimming pool tiles up to

250 x125mm sizes (thickness to be specified by the
manufacturer) or approved make in all colours and
shades, laid on 20mm thick cement mortar 1:4 (1
39 NSOR cement : 4 coarse sand) including mixing of adhesive, Sqm 1600.00 2265.75 ₹ 36,25,200.00
grouting the joints with white cement and matching
pigments etc. complete.

ANTI SKID MATT FINISH TILE

Providing and laying Endura anti skid matte finished
floor tiles size upto 600x600 mm (8mm to 10mm thick)
of Johnson / Nitco or approved make in all colours,
shades, like White, Ivory, Grey, Fume Red, Brown, laid
40 NSOR on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Sqm 1250.00 1245.00 ₹ 15,56,250.00
Coarse sand) including pointing the joints with white
cement and matching pigments etc., complete.

RUBBER FLOORING
Providing and laying Ecoflex Tuffloor Rubber Flooring
tiles of 1st quality of Ecoflex or equivalent approved
41 NSOR make in colours Fume Red, Brown, laid on standard 1970.00 100.00 ₹ 1,97,000.00
base as per company required etc.complete.

RUBBER MAT
Providing and laying Light Rubber Anti-Fatigue
Drainage Mat, for Wet or Dry Areas, 36" Width x 60"
Length x 1/2" Thickness, of Crown Safewalk, Genuine
42 NSOR Joe or equivalent brand in Black or brown colour 3450.00 125.00 ₹ 4,31,250.00
approved by EIC and architects etc.complete.

ROOFING AND CEILING WORK

Providing and fixing Trapezoidal (Top width 0.3m,
bottem width 0.2m and depth 0.1m) plain G.S. sheet
43 12.7.2 gutter with iron brackets 40x3mm size, bolts, nuts and
washers etc. including making necessary connections
with rain water pipes complete.
0.80mm thick with zinc coating not less than 275gm/m²
a 12.7.2.1 Meter 360 324.00 150.00 ₹ 48,600.00

Page 8 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Providing and fixing at all height false ceiling including
providing and fixing of frame work made of special
sections power pressed from M.S. sheet and galvanised
in accordance with zinc coating of grade 350 as per IS :
277 and consisting of angle cleats of size 25mm wide x
1.6mm thick with flanges of 22mm and 37mm at
1200mm centre to centre one flange fixed to the ceiling
with dash fastener 12.5mm diax40mm long with 6mm
dia bolts to the angle hangers of 25x25x0.55mm of
required length, and other end of angle hanger being
fixed with nut and bolts to G.I. channels 45x15x0.9mm
running at the rate of 1200mm centre to centre to which
the ceiling section 0.5mm thick button wedge of 80mm
with tapered flanges of 26mm each having clips of
44 12.45 10.5mm at 450mm centre to centre shall be fixed in a
direction perpendicular to
G.I. channel with connecting clips made out of 2.64mm
dia 230mm long G.I. wire at every junction including
fixing the gypsum board with ceiling section and peri
meter channels 0.5mm thick 27mm high having flanges
of 20mm and 30mm long,
the perimeter of ceiling fixed to wall/partition with the
help of rawl plugs at 450mm centre to centre with
25mm long drive-all screws
@ 230mm interval including jointing and fixing to
a flush finish of tapered and square edges of the board
with recommended filler, jointing tapes, finisher and
two coats of primer suitable for board as per
manufactures specification and also including the cost
12.5 mm thick tapered edge gypsum board conforming
to IS: 2095-
a 12.45.1 Sqm 718 646.20 517.20 ₹ 3,34,215.00
Part I.

Providing & fixing UV stabilised fiberglass reinforced

plastic sheet roofing up to any pitch including fixing
with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm
dia. G.I plain/bitumen washers complete but excluding
the cost of purlins, rafters, trusses etc. The sheets shall
be manufactured out of 2400 TEX panel rovigs
incorporating minimum 0.3% Ultra-violet stabiliser in
45 12.47 resin system under approximately 2400 psi and hot
cured. They shall be of uniform pigmentation and
thickness without air pockets and shall conform to IS
10192 and IS 12866.The sheets shall be opaque or
translucent, clear or pigmented, textured or smooth as
specified.

2mm thick corrugated (2.5" or 4.2" or 6") or step-down

a 12.47.1 Sqm 891 801.90 645 ₹ 5,17,226.00
(2" or 3" or 6" ) as specified.

FINISHING
46 13.1 12 mm cement plaster of mix :
a 13.1.1 1:4 (1 cement: 4 fine sand) Sqm 108 97.20 8822.85 ₹ 8,57,581.00

15mm cement plaster on the rough side of single or half

47 13.2
brick wall of mix :
a 13.2.1 1:5 (1 cement: 5 fine sand) Sqm 119 107.10 1911.00 ₹ 2,04,668.00

48 13.6 20 mm cement plaster of mix :

Page 9 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
a 13.6.1 1:4 (1 cement: 4 coarse sand) Sqm 153 137.70 1052.00 ₹ 1,44,860.00

49 13.16 6 mm cement plaster of mix :

a 13.16.1 1:3 (1 cement: 3 fine sand) Sqm 83 74.70 2665.80 ₹ 1,99,135.00

50 13.18 Neat cement punning Sqm 25 22.50 224.00 ₹ 5,040.00

Rough cast plaster upto 10m height above ground level

with a mixture of sand and gravel or crushed stone from
6mm to 10mm nominal size dashed over and including
the fresh plaster in two layers, under layer 12mm
51 13.19 cement plaster 1:4 (1 cement: 4 coarse sand) and
top layer 10mm cement plaster 1:3 (1 cement: 3 fine
sand) mixed with 10% finely grounded hydrated lime by
volume of cement.

a 13.19.1 Ordinary cement finish using ordinary cement 257 231.30 764.40 ₹ 1,76,806.00

Pebble dash plaster upto 10m height above ground level

with a mixture of washed pebble or crushed stone
6mm to 12.5mm nominal size dashed over and
including fresh plaster in two layers under layer 12mm
52 13.20 cement plaster 1:4 (1 cement: 4 coarse sand) and top Sqm 248 223.20 764.40 ₹ 1,70,614.00
layer 10mm cement plaster with cement mortar 1:3 (1
cement: 3 fine sand) mixed with 10% finely grounded
hydrated lime by volume of cement.

Finishing walls with water proofing cement paint of

53 13.44
required shade
New work (Two or more coats applied @ 3.84 kg/10
a 13.44.1 Sqm 37 33.30 2358 ₹ 78,521.00
sqm).

Finishing walls with Acrylic Smooth exterior paint of

54 13.46
required shade.
New work (Two or more coat applied @ 1.67 ltr/10
sqm over and including base coat of water proofing
a 13.46.1 cement paint applied @ Sqm 64 57.60 1911.00 ₹ 1,10,074.00
2.20 kg/ 10 sqm).

Wall painting with plastic emulsion paint of approved

55 13.60 brand and manufacture to give an even shade:

a 13.60.1 Two or more coats on new work Sqm 53 47.70 8822.85 ₹ 4,20,850.00

Finishing walls with Deluxe Multi surface paint

56 13.48 system for interiors and exteriors using Primer as
per manufacturers specifications :
Two or more coats applied @ 1.25 ltr/10 sqm.
a 13.48.1 over and including one coat of Special primer applied Sqm 75 67.50 1024.00 ₹ 69,120.00
@ 0.75 ltr/10 sqm.

Painting Steel work with Deluxe Multi Surface Paint to

give an even shade. Two or more coat applied @0.90
57 13.48.3 ltr/10 sqm over an under coat of primer applied @ 0.80 Sqm 65 58.50 255 ₹ 14,918.00
ltr/ 10 sqm of approved brand or manufacture

Page 10 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Painting with black anti-corrosive bitumastic paint of
58 13.65 approved brand and manufacture to give an even shade:

a 13.65.1 Two or more coats on new work. Sqm 35 31.50 512.00 ₹ 16,128.00

Painting of artistic work by good quality paint on

prepare surface by base coat of primer as required as per
59 NSOR Sqm 1300.00 768.90 ₹ 9,99,570.00
drawing and design provided by architect.

ALUMINIUM WORK
Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded
built up standard tubular sections/ appropriate Z
sections and other sections of approved make
conforming to IS: 733 and IS : 1285, fixed with rawl
plugs and screws or with fixing clips, or with
expansion hold fasteners including necessary
filling up of gaps at junctions, at top, bottom
and sides with required PVC/neoprene felt etc.
60 17.1 Aluminium sections shall be smooth, rust free,
straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap
beading for glazing / paneling, C.P. brass / stainless
steel screws, all complete as per architectural
drawings and the directions of Engineer-in-charge.
(Glazing
and paneling to be paid for separately) :

a 17.1.1 For fixed portion

Polyester powder coated aluminium (minimum
i 17.1.1.3 thickness of Kg 374 336.60 3182.14 ₹ 10,71,108.00
polyester powder coating 50 micron)
For shutters of doors, windows & ventilators
including providing and fixing hinges/ pivots and
making provision for fixing of fittings wherever
b 17.1.2 required including the cost of PVC / neoprene gasket
required (Fittings shall be paid for separately).

Polyester powder coated aluminium (minimum

i 17.1.2.3 thickness of Kg 396 356.40 1983.56 ₹ 7,06,941.00
polyester powder coating 50 micron)
Providing and fixing glazing in aluminium door,
window, ventilator shutters and partitions etc. with
PVC/ neoprene gasket etc. complete as per the
61 17.3 architectural drawings and the directions of engineer-
in- charge (Cost of aluminium snap beading shall be
paid in basic item):

a 17.3.1 With float glass panes of 4.0 mm thickness Sqm 679 611.10 652.80 ₹ 3,98,926.00

WATER PROOFING WORK

Page 11 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Providing and laying integral cement based treatment
for water proofing on horizontal surface at all depth
below ground level for under ground structures as
directed by Engineer-in-Charge and consisting of :
(i) Ist layer of 22mm to 25mm thick approved and
specified rough stone slab over a 25mm thick base of
cement mortar 1:3 (1 cement : 3 coarse sand) mixed
with water proofing compound conforming to IS:2645
in the recommended proportion over the leveling course
(leveling course to be paid separately). Joints sealed and
62 18.1
grouted with cement slurry mixed with water proofing
compound. (ii) 2nd layer of
25mm thick cement mortar 1:3 (1 cement: 3 coarse
sand) mixed with water proofing compound in
ecommended proportions. (iii) Finishing
top with stone aggregate of 10mm to 12mm nominal
size spreading @ 8 cudm/sqm thoroughly embedded in
the 2nd layer.

a 18.1.1 Using rough kota stone. Sqm 753 677.70 1522.00 ₹ 10,31,459.00
Providing and laying integral cement based treatment
for water proofing on the vertical surface by fixing
specified stone slab
22 mm to 25mm thick with cement slurry mixed
with water proofing compound conforming to
IS:2645 in recommended proportions with a gap of
20mm (minimum) between stone slabs and the
receiving surfaces and filling the gaps with neat cement
63 18.2 slurry mixed with water proofing compound
and finishing the exterior of stone slab with cement
mortar 1:3 (1 cement : 3 coarse sand) 20mm thick with
neat cement punning mixed with water proofing
compound in recommended proportion complete at
all levels and as directed by Engineer-
in-charge :

a 18.2.1 Using Kota Stone Sqm 879 791.10 895.00 ₹ 7,08,035.00

Water proofing work of Basement Vertical Walls. i)

Surface preparation of vertical wall surface free from all
loose sand and particles dust. including nozal grouting
at every and all construction joints & as required.
Chipping the surface wherever required to take out
loose mortar, laintance etc. ii) Application of polymer
modified mortar Ultra tech Super Stucco for repairing
of Joints, minor wall cracks and small pot holes. iii) Pre
wetting of surface area before application of UltraTech
64 Non SOR Seal & Dry to avoid absorption of water from material. Sqm 437.00 895.00 ₹ 3,91,115.00
iv) Application of single component, polymer modified
flexible water proof coating two coats of UltraTech Seal
and Dry on wall area over plastered surface which is
cleaned by brush as per instruction of manufacturer. v)
Allow the coating to self cure itself for minimum 48
hours and then do the test or next application.

Page 12 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Providing and laying water proofing treatment on
roofs of slabs by applying cement slurry mixed with
water proofing cement compound consisting of applying:
(a) after surface preparation, first layer of slurry of
cement @
0.488 kg/sqm mixed with water proofing cement
compound @
0.253 kg/sqm.
(b) laying second layer of Fibre glass cloth when the
first layer is still green. Overlaps of joints of fibre cloth
should not be less than 10 cm.
(c) third layer of 1.5 mm thickness consisting of slurry
65 18.6 of cement @ 1.289 kg/sqm mixed with water proofing Sqm 315 283.50 1052.00 ₹ 2,98,242.00
cement compound @ 0.670 kg/sqm and coarse sand
@1.289 kg/sqm. This will be allowed to air cure for 4
hours followed by water curing for 48 hours. The entire
treatment will be taken upto 30cm on parapet wall and
tucked into groove in parapet all around.
(d) fourth and final layer of brick tiling with cement
mortar (which will be paid for separately For the
purpose of measurement the entire treated surface will
be measured.

Providing and Placing in position suitable PVC water

stops conforming to IS:12200 for construction/
expansion joints between two RCC members and fixed
66 18.4 to the reinforcement with binding wire before pouring
concrete etc. complete :

Serrated with central bulb (225mm wide, 8-11mm

18.4.1 Meter 426 383.40 350.00 ₹ 1,34,190.00
thick).

Providing and fixing mirror of superior glass (of

approved quality) and of required shape and size with
67 25.32
plastic moulded frame of approved make and shade
with 6 mm thick hard board backing :
a 25.32.2 Rectangular shape 453x357mm Each 685 616.50 25.00 ₹ 15,413.00
b 25.32.4 Rectangular shape 1500x450 mm Each 1729 1556.10 16.00 ₹ 24,898.00

Providing and fixing stainless steel ( Grade 304) railing

made of Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and making
curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c
fixing the railing with necessary accessories & stainless
steel dash fasteners , stainless steel bolts etc., of
68 DSR 10.28 required size, on the top of the floor or the side of waist KG 472.4 425.16 2544.00 ₹ 10,81,607.00
slab with suitable arrangement as per approval of
Engineer-incharge, (for payment purpose only weight of
stainless steel members shall be considered excluding
fixing accessories such as nuts, bolts, fasteners etc.)

NON SOR ITEM

Page 13 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Providing and Supplying lane ropes with anchor
69 Non SOR Each 1680.00 60.00 ₹ 1,00,800.00
brackets

Providing and fixing Toilet cubicle made of

heat,bacterial,water,Chemical,Scratch ,impact and Anti
Bacterial resistant 12mm thick Solid Compact laminate
panels .Finish of the compact laminate should be
suede/Raw silk which includes door,pilasters &
Intermediate panels finished with approved textures
,shades as per the detailed drawings and as per IS2046
and as per fire retardant BS-476/97 standard ,including
providing and fixing in neccessary hardware made out
of Nylone polyamide Grade-6 and Aluminum powder
70 Non SOR coated top rail.Screws will be 304 grade stainless steel Each 20030.00 42.00 ₹ 8,41,260.00
.Thermoplastic palm design pedestal footing with non-
corosive steel inserts.The base diameter 65mm and neck
diameter of 33mm anchored to the floor with grade 304
stainless steel screws with push fit capping at a
clearance height of 150mm.Aluminum U channel
should be used for the for fixing of intermediate panels
to the walla. GREENLAM or Equivalent Make.

Supplying and fixing structural Glazing works with 12

71 Non SOR mm toughned glass Fixing and Erection Sqm 2370.00 400.80 ₹ 9,49,896.00
Complete.(Excluding Cost of Structural Steel)

SS 316 SS Leader in 43 mm / 14 G Pipe with Flat Step

72 Non SOR
Trades
a 4 Step Ladder Each 21500.00 4.00 ₹ 86,000.00
b 5 Step Ladder Each 24500.00 4.00 ₹ 98,000.00
c 6 Step Ladder Each 26500.00 4.00 ₹ 1,06,000.00

Providing & fixing at position of Stainless steel Godrej

prime quality CRCA steel with anti-corrosive treatment
lockers including lock, haldle, label holder & doors have
ventilating louvers for air circulation. color in Prince
73 Non SOR Grey and Olive green colours. Size of Locker unit Each 15452.00 115.00 ₹ 17,76,980.00
380x457 & 1830 mm height. position of units as per
drawing and design etc. complete

Providing and laying china mosaic flooring on terrace

with 6 mm thk white or coloured glazed tiles chips of
min. 25-35 mm approved square or rectanglular shape
and fixing it. Before starting a work remuve all old
existing floorinf and open old surface with wire brush
and fill cracks if shown with water proof material then
for making level gps work done in min. 45-50 mm thk
and fixing china mosaic in cement mortar 1:3 with neet
74 Non SOR cement slurry at top and filling the gap with white or Sqm 760.00 255.00 ₹ 1,93,800.00
colour cement with finishing smooth surface and even
shade including cleaning of all dust ,dirt and other
foreign mater rate including for making colour patta
round vata with fixing neccsary water spout opening
gap etc

Page 14 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Supplying/Providing/Finishing, Testing and
Comissioning of Steam Bath unit as per specification
75 Non SOR mentioned in scope of work and along with signage Each 150000.00 2.00 ₹ 3,00,000.00
board as per instruction of Engineer in charge.

Supplying/Providing/Finishing, Testing and

Comissioning of Sauna Bath unit as per specification
76 Non SOR mentioned in scope of workalong with signage board as Each 450000.00 2.00 ₹ 9,00,000.00
per instruction of Engineer in charge.

Supplying/Providing/Finishing, Tresting and

Comissioning of of Jacuzzi for 6 persons with filtration
equipment, flow fittings, under water lights
illumination, spa fittings, maintenance accessories,
pumps, online heater, associated electrical and plumbing
77 Non SOR for jacuzzi, electrical control panels, associated jacuzzi Each 550000.00 2.00 ₹ 11,00,000.00
MS format and civil works.
as per specification and mentioned scope of work along
with signage board as per instruction of Engineer in
charge.

Supplying/Providing/Finishing, Testing and

Comissioning of Chilled Shower Unit as per
78 Non SOR specification mentioned in scope of work along with Each 275000.00 2.00 ₹ 5,50,000.00
signage board as per instruction of Engineer in charge.

Synthetic Flooring as per Specification Given by

79 Non SOR Sqm 1200.00 597.60 ₹ 7,17,120.00
Original Manufacture

Horticulture

Supplying and stacking of good earth at site including

80 19.2 royalty and carriage up to 1 km (earth measured in Cum 184 165.60 765.00 ₹ 1,26,684.00
stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty

81 19.3 and carriage up to 1 km (sludge measured in stacks will Cum 162 145.80 765.00 ₹ 1,11,537.00
be reduced by 8% for payment).

Supplying and stacking at site dump manure from

82 19.4 approved source, including carriage up to 1 km (manure
measured in stacks will be reduced by 8% for payment)

a 19.4.1 Screened through sieve of I.S. designation 20mm Cum 105 94.50 765.00 ₹ 72,293.00
b 19.4.2 Screened through sieve of I.S. designation 16mm Cum 115 103.50 765.00 ₹ 79,178.00
c 19.4.3 Screened through sieve of I.S. designation 4.75mm Cum 123 110.70 765.00 ₹ 84,686.00

Extra for providing and mixing water proofing material

1kg/Ba
83 13.21 in cement plaster work in proportion recommended by 66 59.40 30.00 ₹ 1,782.00
g
the manufacturers.

Page 15 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
Manhole inside size 90x80 cm and 45 cm deep
including C.I. cover with frame (light duty) 455x610
84 24.4.1 mm internal dimensions total weight of cover and frame Each 7377 6639.30 10.00 ₹ 66,393.00
to be not less than 38 kg (weight of cover 23 kg and
weight of frame 15 kg) :

Uprooting weeds from the trenched area after 10 to 15

100sq
85 19.6 days of its flooding with water including disposal of 137.5 123.75 65.00 ₹ 8,044.00
m
uprooted vegetation.

100sq
86 19.7 Fine dressing the ground 103 92.70 65.00 ₹ 6,026.00
m

Spreading of sludge, dump manure or/and good earth in

87 19.8 required thickness (Cost of sludge, dump manure or/ Cum 15 13.50 765.00 ₹ 10,328.00
and good earth to be paid separately).

Mixing earth and sludge or manure in proportion

88 19.9 Cum 102 91.80 765.00 ₹ 70,227.00
specified or directed.

Grassing with „Doob‟ grass including watering and

maintenance of the lawn for 30 days or more till the
89 19.1 grass forms a thick lawn free from weeds and fit for
mowing including supplying good earth if needed (the
good earth shall be paid for separately).

100sq
a 19.10.1 In rows 15 cm apart in either direction. 156 140.40 30.00 ₹ 4,212.00
m
100sq
b 19.10.2 In rows 7.5 cm apart in either direction. 324 291.60 30.00 ₹ 8,748.00
m
100sq
c 19.10.3 In rows 5 cm apart in either direction. 496 446.40 30.00 ₹ 13,392.00
m

Providing and laying 60 mm thick factory made cement

concrete interlocking paver block of M -30 grade made
by block making machine ith strong vibratory
compaction and of approved size and design/shape laid
90 11.46 Sqm 454 408.60 1195.00 ₹ 4,88,277.00
in required colour and pattern over and including 50
mm thick compacted bed of course sand, filling the
joints with coarse sand etc. all complete as per the
direction of Engineer-in-charge.

Preparation of beds for hedging and shrubbery by

excavating 60cm deep and trenching the excavated base
to a further depth of 30cm, refilling the excavated earth
after breaking clods and mixing with sludge or manure
in the ratio of 8:1(8 parts of stacked volume of earth
after reduction by 20% : one part of stacked volume of
91 19.13 sludge or manure after reduction by 8%), flooding with Cum 62 55.80 332.00 ₹ 18,526.00
water, filling with earth if necessary, watering and
finally fine dressing, leveling etc. including stacking and
disposal of materials declared unserviceable and surplus
earth by spreading and leveling as directed, within a
lead of 50m lift up to 1.5 m complete (cost of sludge,
manure or extra earth to be paid for separately).

Page 16 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction

Digging holes in ordinary soil and refilling the same

with the excavated earth mixed with manure or sludge
in the ratio of 2:1 by volume (2 parts of stacked volume
of earth after reduction by 20% : 1 part of stacked
92 19.14 volume of manure after reduction by 8%) flooding with
water, dressing including removal of rubbish and
surplus earth, if any with all leads and lifts (cost of
manure, sludge or extra good earth if needed to be paid
for separately) :

a 19.14.1 Holes 1.2 m dia and 1.2 m deep. Each 182 163.80 36.00 ₹ 5,897.00
b 19.14.2 Holes 60 cm dia, and 60 cm deep. Each 24 21.60 36.00 ₹ 778.00

Filling mixture of earth and sludge or manure in the

desired proportion in trenches, flooding with water and
93 19.20 Cum 5 4.50 765.00 ₹ 3,443.00
leveling (cost of supplying earth and sludge or manure
and mixing excluded).

Flooding the ground with water including making 100sq

94 19.24 78 70.20 65.00 ₹ 4,563.00
kiaries and dismantling the same. m

TREES
95 DSR 2016 Wodyetia Difurcata Each 1100.00 10.00 ₹ 11,000.00

96 DSR 2016 Babusoideae Each 32.50 10.00 ₹ 325.00

97 DSR 2016 Cassia Fistula Each 60.00 10.00 ₹ 600.00

98 DSR 2016 Azadirachta Indica Each 60.00 10.00 ₹ 600.00

99 DSR 2016 Delonis Regia Each 60.00 10.00 ₹ 600.00

100 Non SOR Samanea Saman Each 1000.00 10.00 ₹ 10,000.00

101 DSR 2016 Plumeria Each 110.00 10.00 ₹ 1,100.00

102 DSR 2016 Callistemon Each 60.00 10.00 ₹ 600.00

103 DSR 2016 Ficus Benjamin Each 100.00 10.00 ₹ 1,000.00

SHRUBS
104 Non SOR Thuja Occidentalis Each 100.00 25.00 ₹ 2,500.00

105 DSR 2016 Ficus panda Each 30.00 25.00 ₹ 750.00

106 Non SOR Rhapis excelsa Each 225.00 25.00 ₹ 5,625.00

Creepers /CLIMBERS

107 Non SOR Pyrostegia venusta Each 250.00 25.00 ₹ 6,250.00

108 UMC Bougainvillea glabra Each 135.00 25.00 ₹ 3,375.00

109 Non SOR ficus pumilla Each 250.00 25.00 ₹ 6,250.00

110 Ground Cover

111 Non SOR Erenthemum Nigram Each 250.00 25.00 ₹ 6,250.00

Page 17 of 51
 Rate after
S UADD SOR UADD
Discription of Item UOM 10% Qty Amount
No. Vol II SOR Rate
Deduction
112 DSR 2016 Clerodendron Inerme Each 20.00 25.00 ₹ 500.00

113 Non SOR Ophiophogan Dwarf Each 250.00 25.00 ₹ 6,250.00

114 Non SOR Wedelia Trilobata Each 175.00 25.00 ₹ 4,375.00

115 Non SOR Angelina sedum Each 200.00 25.00 ₹ 5,000.00

Total Cost ₹ 9,40,68,230.00

Page 18 of 51
 2. ELECTRICAL WORK
Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
1 1.2 Point Wiring in surface rigid P.V.C. conduit system with Modular
Point wiring including metallic switch box, sheet, switches, sockets,
lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable
FR with copper multi strand conductor ISI marked in Surface rigid
P.V.C. conduit (MMS) ISI Marked of suitable size and 1.5 Sq. mm.
PVC insulated copper earth continuity conductor of green colour
inside conduit including painting etc. as required as per specification
for :-
a 1.2.1 Light Point/Fan Points.
a) Short point Each 370 333 27 ₹ 8,991.00
b) Medium point Each 633 569.7 173 ₹ 98,558.00
c) Long point Each 944 849.6 268 ₹ 2,27,693.00

b 1.2.2 3 Pin 6 Amp socket outlet on Separate Board

a) Short point Each 420 378 13 ₹ 4,914.00
b) Medium point Each 683 614.7 27 ₹ 16,597.00
c) Long point Each 993 893.7 13 ₹ 11,618.00

c 1.2.3 Call Bell / Buzzer Points

a) Short point Each 373 335.7 5 ₹ 1,679.00
b) Medium point Each 643 578.7 1 ₹ 579.00
c) Long point Each 958 862.2 5 ₹ 4,311.00

d 1.2.4 Twin Control light points

a) Short point Each 370 333 2 ₹ 666.00
b) Medium point Each 680 612 7 ₹ 4,284.00
c) Long point Each 1046 941.4 7 ₹ 6,590.00
e 1.3.6 Circuit Wiring
Wiring for circuit wiring with PVC insulated cable FR with copper
multi strand conductor ISI marked in concealed rigid P.V.C. conduit
2
(HMS) of ISI marked suitable size including painting etc. as required
as per specification
a a) 2x2.5 Sq.mm. meter 116 104.4 2098 ₹ 2,19,031.00
b b) 4x2.5 Sq.mm. meter 162 145.8 2098 ₹ 3,05,888.00

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY)

1.4
SYSTEM WITH MODULER ACCESSORIES

Point wiring including metallic switch box, sheet, switche, socket,

lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable
FR with copper multi strand conductor ISI marked in concealed rigid
3 P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm.
PVC insulated copper earth continuity conductor of green colour
inside conduit including painting etc. as required as per specification
for :-
a 1.4.1 Light Point/Fan Points.
b) Medium point Each 806 725.4 314 ₹ 2,27,776.00
c) Long point Each 1204 1083.6 157 ₹ 1,70,125.00

b 1.4.2 3 Pin 6 Amp socket outlet on Separate Board

a) Short point Each 507 456.3 13 ₹ 5,932.00
b) Medium point Each 856 770.4 69 ₹ 53,158.00
c) Long point Each 1254 1128.6 41 ₹ 46,273.00
c 1.4.3 Call Bell / Buzzer Points
a) Short point Each 460 414 1 ₹ 414.00
b) Medium point Each 816 734.4 2 ₹ 1,469.00
c) Long point Each 1218 1096.2 2 ₹ 2,192.00
d 1.4.4 Twin Control light points
a) Short point Each 458 412.2 7 ₹ 2,885.00
b) Medium point Each 853 767.7 13 ₹ 9,980.00
c) Long point Each 1306 1175.4 13 ₹ 15,280.00

Page 19 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Point wiring including metallic switch box, sheet, switche, socket for 3
pin 6 Amp. Socket outlet point with 1.5 Sq. mm. PVC insulated cable
FR with copper multi strand conductor ISI marked in concealed rigid
e 1.4.5 P.V.C. conduit (HMS) ISI marked of suitable size and 1.5 Sq. mm. Each 257 231.3 138 ₹ 31,919.00
PVC insulated copper earth continuity conductor of green colour
inside conduit with required materials as per specification on same
board .
POWER WIRING IN CONCEALED RIGID STEEL CONDUIT
2.5.7
SYSTEM WITH MODULAR ACCESSORIES

Point wiring including metallic switch box, sheet for 3 Pin 16 Amp.
Socket Outlet Point with 4 Sq. mm. PVC insulated cable FR with
copper multi strand conductor ISI marked in Concealed rigid Steel
4 Conduit ISI Marked of suitable size including painting etc. with 16
Amp. Switch & Socket / S.S.Combined 16 Amp. of ISI Marked and 4
Sq. mm. PVC insulated copper earth continuity conductor of green
colour inside conduit as per specification for :-

On Separate Board
a C. Long Point Each 2310 2079 55 ₹ 1,14,345.00
b D. Extra Long -I Each 2842 2557.8 13 ₹ 33,251.00
2.8 METALLIC SWITCH BOXES

Supplying and fixing factory fabricated hot dip galvanised switch box
for normal flush type accessories of minimum 1.2 mm (18 swg gauge)
thickness with earth terminal stud with nut and washer, with 3 mm
5
thick synthetic phenollic resin bonded laminated sheet conforming to
grade P-I of IS:2036-1974 on surface / concealed including painting
etc. as required as per specification:

a 3 MS Box 180 mm X 100 mm X 60 mm Deep Each 104 93.6 20 ₹ 1,872.00

b 4 MS Box 200 mm X 125 mm X 60 mm Deep Each 123 110.7 25 ₹ 2,768.00
c 5 MS Box 200 mm X 250 mm X 60 mm Deep Each 172 154.8 25 ₹ 3,870.00
d 6 MS Box 250 mm X 300 mm X 60 mm Deep Each 227 204.3 12 ₹ 2,452.00
2.9 MODULAR SWITCH BOXES
Supplying and fixing of approved make modular type metal box with
6 modular frame/ base plate and cover plate including fixing in
concealed / surface excluding switch,socket etc. as required for:-
a 1 1 Or 2 Module Each 104 93.6 50 ₹ 4,680.00
b 2 4 Module Each 173 155.7 50 ₹ 7,785.00
c 3 6 Module Each 176 158.4 69 ₹ 10,930.00
d 4 8 Module Each 202 181.8 125 ₹ 22,725.00
e 5 12 Module Each 255 229.5 62 ₹ 14,229.00
CIRCUIT WIRING IN EXISTING CONDUIT / PVC CASING
4.3
CAPPING
Supplying and drawing single core PVC insulated cable FR with
7 copper multi strand conductor ISI marked in existing rigid conduit in
surface or concealed as per specification.
a 4.3.2 2.5 Sq mm cable
i 3 3 X 2.5 sq mm meter 96 86.4 1049 ₹ 90,634.00
ii 4 4 X 2.5 sq mm meter 128 115.2 1573 ₹ 1,81,210.00
b 4.3.3 4.00 Sq mm cable
i 3 3 X 4.00 sq mm meter 131 117.9 1049 ₹ 1,23,677.00
ii 4 4 X 4.00 sq mm meter 175 157.5 1573 ₹ 2,47,748.00
c 4.3.4 6.00 Sq mm cable
i 3 3 X 6.00 sq mm meter 173 155.7 419 ₹ 65,238.00
ii 4 4 X 6.00 sq mm meter 231 207.9 419 ₹ 87,110.00
d 6.4 3 Pin 5 Amp Socket Outlet Point on Same Board
3 Pin 5 Amp Socket Outlet Point on Same Board with modular
i 2 Each 241 216.9 37 ₹ 8,025.00
accessires
e 6.6 3 WIRE SUB-MAIN
i 1 3 X 2.5 meter 76 68.4 1049 ₹ 71,752.00
ii 2 3 X 4.0 meter 112 100.8 1573 ₹ 1,58,558.00
f 6.8 4 WIRE SUB-MAIN
i 1 4 X 2.5 sq mm meter 97 87.3 1573 ₹ 1,37,323.00
ii 2 4 X 4.0 sq mm meter 145 130.5 1836 ₹ 2,39,598.00
iii 3 4 X 6.0 sq mm meter 202 181.8 524 ₹ 95,263.00

Page 20 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Supplying of ISI Marked AutomaticTransfer Switches (ATS)
8 7.5 confirming to IEC : 60947-1 & IEC : 60947-6-1 with automatic inbuilt
time delay 4 pole, 415 V with two earthing terminals if
a 5 400 Amp (open execution ) Each 75973 68375.7 1 ₹ 68,376.00

Supplying of ISI Marked and approved make of Moulded Case Circuit

Breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC
9 8
supply with respective interrupting capacity (KA) at 415 Volts cited
against their range standard conforming to IS - 8828

a 8.1 MCCB with Breaking Capacity 25 KA at 415 V

i 1 Current Rating -25 to100 Amps & 70% -100% adjustable Each 4939 4445.1 4 ₹ 17,780.00
ii 2 Current Rating -125 Amps & 70% -100% adjustable Each 6241 5616.9 4 ₹ 22,468.00
iii 3 Current Rating -160 Amps & 70% -100% adjustable Each 8710 7839 2 ₹ 15,678.00
iv 4 Current Rating -200 Amps & 70% -100% adjustable Each 8580 7722 2 ₹ 15,444.00
b 8.2 MCCB with Breaking Capacity 35 KA at 415 V
Current Rating -315 Amps & Adjustable: 70% -100% thermal & 5-
i 4 Each 20907 18816.3 1 ₹ 18,816.00
10 times magnetic setting
Supplying of ISI Marked and accepted standard of Miniature Circuit
Breaker (MCB) of 'C' series suitable for 240/415 Volts, 50 Cycle , 10
10 8.5
kA Value AC supply confirming to IS : 8828 : 1996, IEC : 60898
:2002 but without enclosures :-
i 8.5.1 SINGLE POLE (SP)
2 6 Amp to 32 Amp Rating Each 166 149.4 251 ₹ 37,499.00
ii 8.5.3 DOUBLE POLE (DP)
2 6 Amp to 32 Amp Rating Each 559 503.1 50 ₹ 25,155.00
iii 8.5.5 FOR TRIPLE POLE & NEUTRAL(TPN)
3 For 40 Amps. Rating only. Each 1428 1285.2 37 ₹ 47,552.00
4 50 Amp to 63 Amp Rating Each 1678 1510.2 21 ₹ 31,714.00

Supply of approved make powder coated sheet steel encloser SPN

11 8.5.(B) MCB DB inclusive of Busbar, Neutral bar, Earth bar & two earth
terminals etc. complete as per IS:13032( exclusive of MCB & isolator)-
a 3 4 way double door Each 829 746.1 37 ₹ 27,606.00
b 6 12 way double door Each 1441 1296.9 12 ₹ 15,563.00
Supplying of approved make TPN MCB DB Metal Double Door with
provision for FP MCB/Isolator/RCCB/RCBO as incomer and SP
12 8.6 MCBs as outgoing inclusive of Busbar, Neutral bar, Earth bar & two
earth terminals etc. complete as per IS:13032( exclusive of MCB &
isolator ):
a 1 4 way (4+12) Each 2250 2025 10 ₹ 20,250.00
Supplying and installing of RCBOs (Residual current circuit breaker
with overload and short circuit protection) ISI marked complete as per
I.S. standard confirming to IEC:61009-2-1 & IS:12640-
13 8.12 2:2001,240/415V 50 Hz with 10 kA short circuit withstand capacity
for earth leakage,overload & short circuit protection including
connection in existing enclosure in approved manner as per
specification.
a 8.12.1 DP(4 module)
i 1 2 pole 6 to 25 Amps, 30 mA sensitivity Each 2178 1960.2 41 ₹ 80,368.00
ii 2 2 pole 32 Amps, 30 mA sensitivity Each 2283 2054.7 13 ₹ 26,711.00
b 8.12.2 FP(8 module)
i 3 4 pole 40 Amps, 30 mA sensitivity Each 4313 3881.7 18 ₹ 69,871.00
ii 4 4 pole 63 Amps, 30 mA sensitivity Each 5129 4616.1 18 ₹ 83,090.00
FIXING OF SFUs, DBs,BUSBAR,MCCBs,MCBs, ISOLATORs &
14 8.13
RCBOs
Fixing of metal clad enclosure on 25 X 5 mm flat iron clamps
including supplying and fixing of clamps as required duly embedded
in masonary including cable connection and other required material as
per specification :-
Fixing of metal clad enclosure on 25 X 5 mm flat iron clamps
including supplying and fixing of clamps as required duly embedded
in masonary including cable connection and other required material as
per specification :-

32 Amps DP switch /SPN DB up to 8 way /16 AmpTPN DB up to 3

a 2 Each 87 78.3 52 ₹ 4,072.00
way per pole or 16 Amps TP or TPN switch / 16 Amps 415 V Isolator

Page 21 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Fixing of metal clad enclosure on 25X 25 X 5 mm angle iron clamps
including supplying and fixing of clamps as required duly embedded
15 8.14
in masonary including cable connection and other required material as
per specification :-
Fixing of 63 Amps TP or TPN main switches/ DB 63 Amps. 240/415
Volt 4 to 8 way or 63 Amps change over switch /63 Amps 415 Volt
a 1 Each 170 153 34 ₹ 5,202.00
Isolator /30 Amps 415V TPN DB upto 6 way per pole and busbar 4
way
16 8.16 Fixing of MCB /MCCB/ Isolator
Fixing of MCB / Isolator SP/DP in sheet steel enclosure as required as
a 1 per accepted practice, including mounting on busbar and cable Each 10 9 323 ₹ 2,907.00
connection etc. complete (Labour only )
Fixing of MCB /MCCB Isolator TP /TPN/FP in sheet steel
b 2 enclosure as required as per accepted practice, including mounting on Each 20 18 55 ₹ 990.00
busbar and cable connection etc. complete.
Labour charges for fixing sheet steel enclosures, MCB DB flush
17 8.19 mounting type, as per accepted practice, duly embedded and end plate
completely flushed in wall, cable connection etc.complete :-
FOR S.No :-
a 1 8.5(1) to 8.5(5), 8.6(1) to 8.6 (5) & 8.7(1) Each 167 150.3 27 ₹ 4,058.00
b 2 8.5(6) & 8.5(7), 8.6(6) to 8.6(7), 8.7(2) to 8.7(3) & 8.8(1) to 8.8(3) Each 235 211.5 27 ₹ 5,711.00

Supplying and fixing as per specification Bakelite pendent Holder of

18 9.1 approved make including flexible cord up to 3 Meter length with Each 28 25.2 54 ₹ 1,361.00
necessary materials complete
Supplying and fixing as per specification Call bell / buzzer of approved
19 9.4
make with necessary materials complete.
a 1 Buzzer Each 63 56.7 2 ₹ 113.00
b 4 Remote/cordless bell Each 594 534.6 2 ₹ 1,069.00

Supplying and fixing as per specification Caution / Danger Board as

20 9.11
required of approved make & design with necessary material complete.
a 1 Small Size Each 106 95.4 13 ₹ 1,240.00
b 2 Large Size Each 211 189.9 13 ₹ 2,469.00

Supplying and fixing as per specification bakelite Ceiling rose 3 Plate

21 9.12 Each 28 25.2 54 ₹ 1,361.00
of approved make ISI marked with necessary material complete

Supplying, fixing,testing & commissioning wall / floor mounted LT

Panel primer coated with two coat of enamel paint & provided with
required gasket for dust/ vermin proof with degree of protection IP42
suitable for 415V 3 phase ,50 Hz ,4 wire system fabricated out of
CRCA sheet upto 2 mm thick (1.6 mm for doors) with frame work of
angle iron/ channel/ bolted type construction duly compartmentalised
for incomer,bus section , outgoings cable alleys & CT,PT Ampere
22 9.15 Kg 116 104.4 2000 ₹ 2,08,800.00
Meter ,Volt Meter , selector switches,Frequency Meter ,phase
indicating lamps , energy Meter complete including cost of busbar
supports,detachable cable gland plates,2 earthing terminals, internal
wiring & fixing of separately supplied MCBs, MCCBs,panel mounted
Changeover switch/SFUs, etc. as required but excluding cost of busbar
strips,Ampere Meter, Volt Meter, Selector switch as per approved
design & specification

Supplying and fixing of LT Panel accessaries of approved make in

23 9.16 existing LT Panel including connections etc.as required as per
spececification
a 1 Digital Ampere Meter with CTs with selector switch per set 2354 2118.6 3 ₹ 6,356.00
b 2 Digital Volt Meter with selector switch & HRC fuse per set 2530 2277 3 ₹ 6,831.00
c 3 Frequency Meter Each 1458 1312.2 3 ₹ 3,937.00
d 4 Copper Bus bar strips with PVC sleeves Kg 666 599.4 115 ₹ 68,931.00
e 5 Aluminium bus bar strips with PVC sleeves Kg 209 188.1 461 ₹ 86,714.00
f 6 LED lamps each 242 217.8 14 ₹ 3,049.00
suppling and drawing following pair,0.5 Sq mm PVC Insulated copper
24 9.26 conductor unarmoured telephone cable in existing surface / concealed
,steel / PVC Conduit as required.
a 2 (ii) 2 Pair meter 42 37.8 577 ₹ 21,811.00
b 3 (iii) 4 Pair meter 56 50.4 577 ₹ 29,081.00

Page 22 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
suppling and drawing Co-axial T.V. Cable RG-6 Grade , 0.7 mm Solid
Copper conductor PE Insulated , Shielded with fine tined copper braid
25 9.27 meter 73 65.7 577 ₹ 37,909.00
and protected with PVC Sheath in the existing surface / concealed
,steel / PVC. Conduit as required.
Suppling and fixing of approved make step type Modular electronic,
26 9.31 Fan regulator single/double module including connection etc. as
required on existing board
a 1 upto 120 watt Each 600 540 14 ₹ 7,560.00

Supplying, erection and testing of approved make electric Ceiling fan

of double ball bearing complete with standard down rod, canopy,
27 9.32 hanging shackle, Aluminium blades, without regulator, A.C. 230-250
volts including connections with all necessary material complete as
required confirming to IS :374/1979 with upto date ammendments.

a 1 Ceiling Fan (Energy Saver 50 W)-1200 mm Sweep Each 1888 1699.2 7 ₹ 11,894.00
b 2 Ceiling Fan (Energy Saver 60 W)-1400 mm Sweep Each 1998 1798.2 7 ₹ 12,587.00
Supplying, erection and testing of approved make Wall Mounting fan
complete with Wall Bracket ,canopy, blades, speed Regulator etc .A.C
28 9.33
230- 250 volts with connections and including raw bolt/Anchor hole
fastener etc. complete finished and as required.
a 1 300 sweep Each 1964 1767.6 6 ₹ 10,606.00
Supplying, erection and testing of approved make 'Fresh Air Fan' AC
29 9.35 230-250 volts with connection and including frame bolt/Anchor hole
fasteners etc. compelte finished and as required.
a 2 300mm sweep Each 1347 1212.3 27 ₹ 32,732.00
Supplying, fixing & testing of approved make of T- 5 lamp channel
luminaire with plastic extruded housing with in-built electronic control
30 9.57
gear with decorative end caps with necessary materials connection etc.
complete as required (with lamp)
a 1 T - 5 Lamp 1 X 28 watt Each 838 754.2 25 ₹ 18,855.00
Supply & Installation G.I. pipe for protection of under ground cable
with required material laid 600mm depth below ground level including
31 9.65
excavation in all types of soil & refilling as per direction of the
Engineer-in-charge.
a 9.65.1 25mm dia G.I. Pipe Meter 139 125.1 288 ₹ 36,029.00
b 9.65.2 50mm dia G.I. Pipe Meter 288 259.2 262 ₹ 67,910.00
Supplying and fixing fan clamps of 16 mm dia steel bar as per
32 10.6
specification complete :-
a 2 For R.C.C. Slabs / Beams Each 26 23.4 13 ₹ 304.00
Fixing of fan Regulator on existing switch board in position with
33 10.9 Each 20 18 13 ₹ 234.00
necessary material connection etc.complete as required.
Erection of exhaust fan / wall bracket fan/cabin fan in position with
34 10.1 required PVC cable, rawl bolts etc. complete including connections Each 80 72 27 ₹ 1,944.00
and making wall surface good.

Supplying and fixing down rod of MS pipe for ceiling fan including
35 10.11 meter 101 90.9 13 ₹ 1,182.00
threading, painting, making holes etc. as required complete :-

Earthing with G.I. Earth plate 600mm X 600mm X 6mm thick

including accessories and providing masonary encloser in cement
36 11.3 mortor, cover plate having locking arrangment on the top and G.I. Each 2540 2286 6 ₹ 13,716.00
watering pipe 20mm dia 2.7 meter long etc. (but without charcoal or
coke and salt ) complete as required.
Earthing with Copper Earth plate 600mm X 600mm X 3mm thick
including accessories and providing masonary encloser in cement
37 11.4 mortor, cover plate having locking arrangment on the top and G.I. Each 7618 6856.2 4 ₹ 27,425.00
watering pipe 20mm dia 2.7 meter long etc. (but without charcoal or
coke and salt) complete as required.

Add Extra for using salt and charcoal / coke for G.I. Plate or Copper
38 11.5 Each 520 468 13 ₹ 6,084.00
plate earth electrode as required including excavation & refilling.

Supplying and laying 6 SWG G.I. wire at 0.5Meter below ground level
39 11.7 meter 15 13.5 420 ₹ 5,670.00
as conductor earth electrode including soldering etc. as required.

Supplying and laying 25mm X 5mm G.I. strip at 0.5 meter below
40 11.8 ground level as strip earth electrode including soldering etc. as meter 65 58.5 420 ₹ 24,570.00
required.

Page 23 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Supplying and erecting earth pit of minmum bore dia 150 mm size,
approved make safe earthing electrode consiting pipe in pipe
tecnologie as per IS 3043-1987 made of corriosion free GI pipes
having outer pipe dia of 50 mm having 80-200 micron galvanising,
41 11.4
inner pipe dia of 25 mm having 20-250 micron galavinsing,
connection teriminal dia of 12 mm with constent OHMIC value
sourrounded by highly conductiv compund with high charge disipation
sutible for effective and maintence free earthing
with 3 mtr. Pipe of 80 mm outer dia, 40 mm inner dia and 14 mm
a 4 terminal dia, in soft rock/marshy soil with 25 kg (two bag) back filling each 13300 11970 2 ₹ 23,940.00
compound
42 11.41 Providing back filling compund suitable for safe earthing divice. kg 36 32.4 230 ₹ 7,452.00
Supplying and erection of water tight terminal box of 14 SWG M.S.
Sheet 4mm thick box of required size to erect the suitable kit kat/
MCB/Switch with Top & bottom folded fitted with rubber ring to
make it water tight with pole clamp made from 40x3mm M.S. flat iron
43 13.1
with 2 Nos. Nut and Bolts duly painted with 2 coat of Red Oxide paint
and 2 coat of Aluminium silver paint erected with cable gland but
excluding the cost of the Kit Kat/MCB/Switch complete as per
specification:
a 1 20x15x15Cms. Each 286 257.4 19 ₹ 4,891.00
b 2 30x20x15 Cms. Each 390 351 19 ₹ 6,669.00
Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100
Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts
44 14.1
grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid
conductor
a 14.1.6 ARMOURED 3½ CORE
i 1 25 Sq.mm(XLPE) meter 289 260.1 288 ₹ 74,909.00
ii 2 35 Sq.mm(XLPE) meter 345 310.5 288 ₹ 89,424.00
iii 3 50 Sq.mm(XLPE) meter 452 406.8 115 ₹ 46,782.00
iv 5 95 Sq.mm.(XLPE) meter 740 666 115 ₹ 76,590.00
v 6 120 Sq.mm.(XLPE) meter 931 837.9 209 ₹ 1,75,121.00
vi 7 150 Sq.mm.(XLPE) meter 1084 975.6 314 ₹ 3,06,338.00
vii 8 185 Sq.mm.(XLPE) meter 1350 1215 420 ₹ 5,10,300.00
viii 9 240 Sq.mm.(XLPE) meter 1716 1544.4 525 ₹ 8,10,810.00
ix 10 300 Sq.mm.(XLPE) meter 2097 1887.3 57 ₹ 1,07,576.00
b 14.1.8 ARMOURED 4 CORE
i 1 6 Sq.mm.(XLPE) meter 168 151.2 1154 ₹ 1,74,485.00
ii 2 10 Sq.mm.(XLPE) meter 183 164.7 1259 ₹ 2,07,357.00
iii 3 16 Sq.mm.(XLPE) meter 229 206.1 577 ₹ 1,18,920.00
14.6 BRASS COMPRESSION GLAND

Supplying and fixing heavy duty cable gland for P.V.C. insulated
45 14.6.1 armoured cable with brass washer, Rubber ring complete erected with
cable and lead connection etc. as per specification complete.
a 1 Gland Size 22mm suitable for cable 2,3,3½ & 4 x upto 6 Sq.mm Each 38 34.2 69 ₹ 2,360.00
Gland Size 22mm suitable for cable 2,3, 3½, 4 x 10 Sq.mm or 2x 16
b 2 Each 44 39.6 125 ₹ 4,950.00
Sq.mm
c 3 Gland size 28mm for 3,4 x 16 Sq.mm Each 66 59.4 46 ₹ 2,732.00
Gland size 32mm for 2,3, 3½, 4 x 25 Sq.mm OR 2,3, 3½ x 35 Sq.mm
d 4 Each 76 68.4 27 ₹ 1,847.00
OR 2,3 x 50 Sq.mm.
e 5 Gland sixe 38mm 3½ x 70 Sq.mm,3x95 Sq.mm Each 119 107.1 7 ₹ 750.00
f 6 Gland Size 45mm 3/3½ x 120 Sq.mm 3½ x 95 Sq.mm 3 x 150 Sq.mm. Each 149 134.1 27 ₹ 3,621.00
g 7 Gland Size 50 mm 3½ x 150 Sq.mm 3 x 185 Sq.mm Each 191 171.9 27 ₹ 4,641.00
h 8 Gland Size 57mm 3 x 225 Sq.mm 3 ½ x 185 Sq.mm Each 248 223.2 13 ₹ 2,902.00
i 9 Gland Size 70mm 3 x 240 Sq.mm 3½ x 300 Sq.mm Each 353 317.7 13 ₹ 4,130.00
14.8 LUGS:-
Supplying and fixing cramping type Alum. lugs as per I.S.S.
Specification suitable for following size of cable with Alu. /Copper
46 solid/stranded conductor evently cramped with high/pressure tool and
connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required
complete.For Conductor Size-
a 1 6mm to 16 Sq.mm Each 5 4.5 830 ₹ 3,735.00
b 2 25 Sq.mm Each 7 6.3 57 ₹ 359.00
c 3 35 Sq.mm Each 9 8.1 57 ₹ 462.00

Page 24 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
d 4 50 Sq.mm Each 14 12.6 27 ₹ 340.00
e 5 70 Sq.mm Each 22 19.8 27 ₹ 535.00
f 6 95 Sq.mm. Each 24 21.6 27 ₹ 583.00
g 7 120 Sq.mm. Each 34 30.6 41 ₹ 1,255.00
h 8 150 Sq.mm. Each 44 39.6 27 ₹ 1,069.00
i 9 180 Sq.mm Each 53 47.7 41 ₹ 1,956.00
j 10 240 Sq.mm. Each 93 83.7 41 ₹ 3,432.00
k 11 300 Sq.mm. Each 129 116.1 13 ₹ 1,509.00
Supplying & fixing pin terminal lugs as per ISS specification suitable
47 14.9 for cable evently cramped with high pressure tool &connection to
switch gear terminal. Copper Lugs Pin Type
a 2 a. Upto 16 Sq.mm Conductor Size Each 12 10.8 1731 ₹ 18,695.00

14.1 CABLE LAYING

48 14.1 CABLE LAYING
Laying of one number PVC insulated and PVC sheathed power cable
7 of 1:1 kV grade of size not exceeding 25 Sq.mm in the existing RCC meter 20 18 3751 ₹ 67,518.00
Hume/Stone/Ware/G.I. pipe as required.
49

Laying of one number PVC insulated and PVC sheathed power cable
50 8 of 1.1 kV grade of size exceeding 25 Sq.mm but not exceeding 400 Sq meter 28 25.2 2885 ₹ 72,702.00
mm in the existing RCC/Hume Stoneware/G.I. Pipe as required.

Supplying, installing, testing and commissioning of 11/0.4 K.V. 3

Phase 50 Cycle oil immersed, naturally cooled, out door type
transformer connected delta on H.T. side and star on L.T. side hand
operated off load, Tap changer switch,above 100 kVA rating and
diagram plate, two earthing terminal, lifting lugs, oil level guage, drain
valve with plug, temperature not exceeding 50ºC on load, oil
a 15
conservator with drain plug, oil filling hole with plug dehydrating
silica gel breather, four unidirectional roller, arcing horns, explosion
vent, terminal arrangement bushing on H.V. side and cable box on LV
side, first filling of oil upto desired level and transformer installing on
existing structure with all Required materials arrangements as required
as per IS specification.

15.2 Copper wound

51 1 200 kVA Each 322645 290380.5 1 ₹ 2,90,381.00
a 15.5 Supplying & fixing of Fire Extinguisher/Refills as per IS specification

b 1 Dry chemical powder (DCP) type- 5kg duly refiled and ready to use Each 2658 2392.2 27 ₹ 64,589.00
52 3 Co2 type dully refiled and ready to used Each 8010 7209 27 ₹ 1,94,643.00
i)Supplying, installing, testing and commissioning of LT Distribution
Box with TPN isolator of 600 amper on incoming,bus bar and 6
53 15.7 S.P.M.C.C.B.of 120 A" Each 28393 25553.7 1 ₹ 25,554.00
.on outgoing side for 200 KVA transformer

Supplying, installing, testing of earth Coil (coil of 115 turns of 50mm

54 15.13 Each 219 198 5 ₹ 990.00
dia, and 2.5 Mtrs. Lead of 4 mm G.I wire.
Supplying and installing Double wall corrugated pipes (DWC) of
HDPE ( IS 14930 Part II -marked ) for cable laid under ground with
necessary connecting sockets/ couplings,tees of same material and at
a 17.4
required depth upto 90cm. below road/ground surface,including
excavation, back filling with excavated material with ramming and
making the surface good.
b 1 50.00mm outside dia. meter 207 186 577 ₹ 1,07,322.00
c 10 200.00mm outside dia. meter 481 432 577 ₹ 2,49,264.00
d 28 25 mm dia ISI marked, PVC conduit mtrs 25.73 24 1731 ₹ 41,544.00
e 29 32 mm dia ISI marked, PVC conduit mtrs 20.32 18 1154 ₹ 20,772.00
f 66 Telephone socket outlet modular type 1 no.s 45 40 13 ₹ 520.00
55 67 T.V socket outlet modular type 1 no.s 44 40 13 ₹ 520.00

Page 25 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Supplying, fixing & testing of approved make of integral type 8 to 9W
bollard cyclindrical shape housing cast aluminium dome shape top
cover fixed with cylindrical shape poly carbonate cover having base
56 Non SOR plate with holes for direct mounting complete with all accessories and Each 6475 6475 99 ₹ 6,41,025.00
control gear box (without lamp) including preparatoion of foundation
including fixing with connection and all required material as required.
Make:

Supplying and fixing 35 to 40 watt integral post top lantern LED

fitting comprises of copper dust finish cast aluminium spigot and spun
aluminium canopy fixed with opal polycarbonate, pipe arrangement for
vertical mounting, open construction driver and accessories are wired
up to terminal block. LED of 1 to 3 W each assembled on single
MCPCB, having color temp 4500 to 6000K & having 50000 burning
57 Non SOR Each 13000 13000 52 ₹ 6,76,000.00
hrs life with minimum @ L 70, system lumen output should be
minimum with efficacy>80lm/W. LED driver PF 0.95 & surge
protection 2KV. The colour rendering index of LED light should be
more than 70. Make-WIPRO- (Model Urban LP06 IP66) or equivalent
in /BAJA/PHILIPS/CROMPTON/HAVELLS/ KESELEC SCHREDER
makes).

Supply,Installtion,Testing and commissionin of garden LED,IP-

67,optically sealed housing with toughned glass totally sealed using
silicon gasket ensuring IP and lifelong perfirmace.High efficiency Cob
58 Non SOR Each 1100 1100 113 ₹ 1,24,300.00
LED mounted available in varies beam engle fronth maintanable
complete with LEDs and driver pre wired upto terminal block range
from 2700K to 6500K 8 watt luminaire,LM output 600.

Supply,Installtion,testing and Commissioning of flexible LED strip

light available in LED power of 4.8 watt per meter to 14.4 per meter
59 Non SOR mtrs 550 550 209 ₹ 1,14,950.00
version,can be cut at marked intervals to suit desired lenghts.IP-20 for
indoor and IP-65 for outdoor.range from 2700K to 6500K.with drivers.

Supply,installtion,testing and commissioning of wall wahser lLED

60 Non SOR light availabale in 6 watt to 10 watt RGB pattern,from one way to four each 2100 2100 120 ₹ 2,52,000.00
way indoor and uotdoor use range from 2700k to 6500K.

Supplying and fixing reccessed mounting LED down lighter, LED of

9W assembled on single MCPCB, having color temp2700to 6000K &
having 50000 burning hrs life with minimum @ L 70, system lumen
output should be minimum with efficacy>80lm/W. LED driver PF 0.95
& THD < 20%. The colour rendering index of LED light should be
61 Non SOR Each 833 833 94 ₹ 78,302.00
more than 70. Housing made of CRCA powder coated frame with glare
free diffused polycarbonate cover. Submission LM 80-08 Form LED
Source Manufacturer & LM79-08 / IS16106 from NABL approved lab.
Manufacturer mandatory. i/c connection wire, testing etc. to complete
the job. 2 Yrs Guarantee certificate from manufacturer.

Supplying and fixing reccessed mounting LED down lighter, LED of

15W assembled on single MCPCB, having color temp2700K to
6000K & having 50000 burning hrs life with minimum @ L 70,
system lumen output should be minimum with efficacy>80lm/W. LED
driver PF 0.95 & THD < 20%. The colour rendering index of LED
light should be more than 70. Housing made of CRCA powder coated
62 Non SOR frame with glare free diffused polycarbonate cover. Submission LM 80- Each 1400 1400 340 ₹ 4,76,000.00
08 Form LED Source Manufacturer & LM79-08 / IS16106 from
NABL approved lab. Manufacturer mandatory. i/c connection wire,
testing etc. to complete the job. 2 Yrs Guarantee certificate from
manufacturer. Wipro make Model no. LD-80 or equivalent in
BAJA/PHILIPS/CROMPTON/HAVELLS /KESELEC SCHREDER
makes

Page 26 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction

Supplying and fixing flood light with high power LED of 150 W
assembled on single MCPCB, system lumens output with efficacy>90
lm/W. luminiare having color temp 4500 to 6000K & 50000 burning
hrs life with minimum @ L 70, The colour rendering index of LED
light should be more than 70. Luminiare comprises of driver, PF 0.95
& surge protection 3KV. Housing made of pressure die cast aluminium
63 Non SOR with heat resistant flat glass, IP65 protection. Submission LM 80-08 Each 22015 19813.5 8 ₹ 1,58,508.00
Form LED Source Manufacturer & LM79-08 / IS16106 from NABL
approved lab. Manufacturer manadatory i/c connection lead, testing etc
to complete the job. 2 Yrs Guarantee certificate from
manufacturer.make-Wipro make (ModelLF07 White) or
BAJA/PHILIPS/CROMPTON/HAVELLS /KESELEC SCHREDER
makes

Supply and fixing of Led in ground luminairs light fixture, LED of 6W

assembled on single MCPCB, ss body dia.54x100 IP65 range fro
64 Non SOR Each 1552 1552 125 ₹ 1,94,000.00
2700k to 6500K indoor and outdoor use.LED CRI >80 and life time
50,000 Hours.

Supply and fixing of led underwater luminaire( for swimming pool

application) Warm White/Blue Color 12VoltX20Watt), Crown SS
Swimming Pool Light SMD(LED) Light (Power LED) 100% Water
Proof , Resin Filled and High Brightness Wall Hanging Light , 9"
Light Diameter THD<9% p.f.>0.7% power efficiency >87% make
osram/seoul or equivalent led viewing angle120 degree led luminous
65 Non SOR efficiency 80-110 LM/W lamp eff.>80% warm white life>50000 Hrs. Each 6700 6700 50 ₹ 3,35,000.00
Pressure die casting aluminium alloy for housing gear/extruded
aluminium lamp housing (heat sink) for better heat transmission grade:-
IP68 Protection: surge protection 2Kv low voltage/over voltage
protection. Makes: AUSTIN model no. CSSL-20R or equvalent in
/BAJA/PHILIPS/CROMPTON/HAVELLS /KESELEC SCHREDER
makes.

Supply, installation, testing and commissioning of stand mounted

panel made of 16 SWG GI sheet, Single door and duly pretreated and
power coated to make it weather proof. The panel shall have 1 Nos.63
Amp TPN MCB incomer, 4 no . of 25 A DP and 6 No. of 6A MCB for
66 Non SOR Each 25000 22500 1 ₹ 22,500.00
outgoing. , 1 No 0-24 Hr electro-mechanical time switch with
memory feature, of suitable rating so that whole street lights get
switched ON automatically at pre decided time. Complete with locking
arrangement. The panel should be supplied with suitable GI stand.

Supply ,Installation,Testing and commissioing of surface mounted

67 Non SOR square/round down light for soft difussed lighting ht. only 32 mm. Each 2555 2555 140 ₹ 3,57,700.00
coloure temparature from 2700K to 6000K, 15 W)
Supply ,Installation,testing and commissioning of step down
68 Non SOR transformer/SMPS 12.5 Amp.240/12 Volt suitable to give power Each 5500 5500 62 ₹ 3,41,000.00
supply to Under water light/ swimming pool lighting fixtures.
Supply, fixing of IP standard water proof junction box with terminal
rail size 200" x 155" x 80"mm.(4 way)Waterproof Function: IP65 ,the
box is i weather-proof, impact-resistant and shatter-proof. It is
particularly suitable for extreme conditions or for outdoor installations.
69 Non SOR Each 2500 2250 42 ₹ 94,500.00
These Junction Boxes are flame-retardant, halogen-free, and are highly
resistant to animal or vegetable fats, mineral oil, diesel, weak acids,
strong and weak alkaline solutions, or alcohol.make Abiable or
equivalent.
Supply and laying of 0.5x24 core PVC Insulated, PVC Round
Sheathed Multi Core Industrial Flexible Cable conforming to IS
70 Non SOR meter 225 225 1154 ₹ 2,59,650.00
694:1990 with Flexible Bright Annealed Copper Conductor for
Voltage Grade upto 1100 Volts make

71 Non SOR Supply, Installation, Testing and commissioning of 2 pin Audio socket Each 240 240 28 ₹ 6,720.00

Supply, Installation, Testing and commissioning of 8w Coloumn

72 Non SOR Each 1800 1800 13 ₹ 23,400.00
speakers with line matching transformer.
Supply, Installation, Testing and commissioning of 8w CEILING
73 Non SOR Each 1600 1600 41 ₹ 65,600.00
speakers with line matching transformer.

Page 27 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Supply, Installation, Testing and commissioning of 6W Loud
74 Non SOR Each 1400 1400 13 ₹ 18,200.00
Speakers with line matching transformer.
Supply, Installation, Testing and commissioning of audio system with
CD player /recorder/ and double channel (L/R) output suitable for 4
75 Non SOR ohm impedence.The system shall be with 1 No. power amplifier Each 50000 50000 1 ₹ 50,000.00
400W+400W and 1 no.table top microphone unit. MAKE - AHUJA
/PHILIPS or Equivalent.

Supply, Installation, Testing and commissioning of distribution box for

PA distribution made out of 16 SWG CRCA sheet with double door
76 Non SOR lockable arrangement having connectors (15 NOS) suitable for 4 Each 1800 1800 1 ₹ 1,800.00
sqmm/2.5sqmm wire with facity for cable termination of 4cx10
sqmm ALAR. Required at each floor for PA wire termination.

Supply,installation, testing and commissioning of Pole 9 Mtr. Ht. made

out of G.I tubular pole, primered and painted with PU base colour of
choice. The column shall also be provided with flush door at the
bottom with proper strengthening to the cutout of the door opening.
Bottom diameter of pole shale be 194 mm, top diameter 114 mm and
base plate dim. 400X400X20 mm .A junction / looping box with
Heavy duty 3 phase connector shall be built into the pole & its
Decorative Arm should be painted with PU colour of the choice of
engineer in-charge. Inclusive of supply and installation of bakelite
sheet with 6A SP C curve MCB & stud type terminal block suitable
for terminating the respective cable. The fitting should be connected
with Copper Flexible wire of 3CX2.5 Sq.mm.The pole as well as
bracket shall be painted by polyurethane (PU) paint of approved colour
77 Non SOR Each 33459 33459 16 ₹ 5,35,344.00
shades. The colour of brackets and that of the pole may be same or
may be different. These shall be decided by Engineer In charge,The
PU colour of the pole as well as bracket shall be guaranteed for at least
5 years from date of handing over the installation. This guarantee shall
be given by the manufacture of pole in writing and shall be counter by
the contractor.The contractor has to submit a certification to IMC from
the manufacture of pole that the pole and its bracket will not bend,
break, buckle or fall due to wind pressure in the Indore city area and
due to weight of the fitting with control gear boxes etc.The approx.
weight of pole with twin brackets shall be 175 kgs. The height of pole
should be 9 mtrs without bracket. (The item is inclusive of
construction of suitable M20 grade RCC foundation as per the
attached specifications).With Ring type bracket.

Supply , installation, testing and comissionIng of outdoor floodlight

160W Specially designed LED Floodlight luminaire having housing of
high pressure die cast aluminum designed to act as heat sink for
efficient heat dissipation and painted in attractive black colour with
78 Non SOR textured finish. Electrochemically brightened and anodized aluminum Each 18004 18004 80 ₹ 14,40,320.00
reflector. Efficacy > or = 90 lum / watt, Colour temperature 4500 to
6000K. LED driver, PF 0.95 & THD < 20%. Lumianire should have
mounting bracket with aiming adjustment. heat resistant toughened
glass Heat resistance toughened glass.

Supply, installation, testing & commissioning of GI

perforated cable tray 2 mm thick without cover and
Non SOR all accessories like perforated tee, 90 degree ₹ 0.00
horizontal bend, elbow, horizontal tee, supports,
hangers etc. of following sizes
a 600 mm (depth - 100 mm) 995 Mtr mtrs 995 30 ₹ 29,850.00
79 b 300 mm (depth - 60 mm) 445 Mtr Mtrs 445 52 ₹ 23,140.00

Page 28 of 51
 Rate after
UADD
S.No. Item Description Unit Rate 10% Qty Amount
S.O.R. No.
Deduction
Supply, installation, testing & commissioning of UV
resistanr , fire retardant FRP Ladder type Cable
trays of following widths, manufactured by copultrusion/
co-extrusion process rungs of size 50
mm x 20 mm of minimum 3 mm thickness at every
250 mm to 300 mm distance, of Sintex or equivalent
a Non SOR ₹ 0.00
make , as required. The flammability shall conorm
to IS: 6746. The trays supplied and installed shall
be complete with coupler plates, junctions, bends
etc as required by the design consultant/EIC. These
shall be counted in length and no extra charges
shall be payable for copuplers, junctions and bends
b 150 mm widthx 150 mm x 40 mm by 4 mm mtrs 1250 210 ₹ 2,62,500.00
c 450 mm width x 150 mm x 40 mm by 4 mm mtrs 970 20 ₹ 19,400.00
80 300 mm width x 150 mm x 40 mm by 4 mm mtrs 365 10 ₹ 3,650.00
Supply, installation, testing & commissioning of
crone type tag block for termination of telephone
a Non SOR
cables/ conduits in MS sheet steel enclosures as
per drawing and specifications.
81 a Tag block 20 pair Each 1940 2 ₹ 3,880.00
Supply, ininstallation, testing & commissioning of
a Non SOR 0.5 mm size copper tinned conductor armoured
PVC cable of following sizes
82 a 20 Pair mtrs 240 52 ₹ 12,480.00
Supplying and fixing of required M.S. angles / flat /
iron/ chanels / reinforcement/ cleating for over head
line support/ brackets/ clamps / cross arm/ cable
tray in Electrical/ LV shafts / Panel room/ Trench
Non SOR kgs 63 99.252 ₹ 6,253.00
etc. including nut bolts and washers with required
fabrication/ holes / welding / cutting / drilling/
theading / fixing etc. with painting by one coat of red
oxide and two coats of aluminium paint.
83 Non SOR Manually operated fire alarm detection system Lumsum 1 291287 ₹ 2,91,287.00
Total ₹ 1,54,70,065.00

Page 29 of 51
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction

CHAPTER 5 UNPLASTICIZED PVC PIPES & FITTINGS FOR

A
(Volume - 1) POTABLE WATER SUPPLY

Providing, laying and jointing following P.V.C. pipes with

solvent cement joint for 6, 8 and 10 kg/ sq. cm. pressures
1 5.1 including testing of joints, cost of jointing materials etc. complete
in all respect. [Conform to IS 4985:2000 and IS 7634
Rates (in Rs.) (PT-3)

a 90 mm dia. RM 128.00 115.20 33 ₹ 3,802.00

b 110 mm dia. RM 182.00 163.80 88 ₹ 14,414.00
c 160 mm dia. RM 493.00 443.70 165 ₹ 73,211.00

CHAPTER 8 HDPE PIPES, MDPE PIPE & SPECIALS AND ZERO

B
(Volume - 1) VELOCITY VALVES

Providing, laying, Jointing & field testing of High Density

Polyethylene pipes, (HDPE) confirming to IS 4984/ 14151/
12786/ 13488 with necessary jointing material like mechanical
connector or jointing pipes by heating to the ends of pipes with
the help of Teflon coated electric mirror/ heater to the required
1 8.1
temperature and then pressing the ends together against each
other, to form a monolithic & leak proof joint by
thermosettingprocess.Itmaybe required to be done with
Jacks/Hydraulic Jacks/ But fusion machine. (50mm & above
fusion jointed & below 50mm mechanical jointed) PE-100

8 Kg/sq.cm :
a 1 20 mm dia RM 34.00 30.60 473 ₹ 14,474.00
b 2 25 mm dia RM 41.00 36.90 341 ₹ 12,583.00
c 3 32 mm dia RM 50.00 45.00 275 ₹ 12,375.00
d 4 40 mm dia RM 64.00 57.60 220 ₹ 12,672.00
e 5 50 mm dia RM 89.00 80.10 110 ₹ 8,811.00
f 6 63 mm dia RM 139.00 125.10 55 ₹ 6,881.00
g 7 75 mm dia RM 195.00 175.50 33 ₹ 5,792.00

2 8.2 Providing and laying Bend 90ْ confirming to IS specifications.

8 Kg/sq.cm :
a 1 20 mm dia Each 27.00 24.30 24 ₹ 575.00
b 2 25 mm dia Each 31.00 27.90 17 ₹ 476.00
c 3 32 mm dia Each 39.00 35.10 14 ₹ 483.00
d 4 40 mm dia Each 44.00 39.60 11 ₹ 436.00
e 5 50 mm dia Each 59.00 53.10 6 ₹ 292.00
f 6 63 mm dia Each 80.00 72.00 6 ₹ 396.00
g 7 75 mm dia Each 120.00 108.00 3 ₹ 356.00

3 8.3 Providing and laying Bend 45ْ confirming to IS specifications.

8 Kg/sq.cm :
a 1 20 mm dia Each 27.00 24.30 25 ₹ 601.00
b 2 25 mm dia Each 30.00 27.00 20 ₹ 535.00
c 3 32 mm dia Each 31.00 27.90 14 ₹ 384.00
d 4 40 mm dia Each 38.00 34.20 11 ₹ 376.00
e 5 50 mm dia Each 49.00 44.10 6 ₹ 243.00
f 6 63 mm dia Each 86.00 77.40 6 ₹ 426.00
g 7 75 mm dia Each 132.00 118.80 4 ₹ 457.00

4 8.4 Providing and laying Equal Tee confirming to IS specifications.

8 Kg/sq.cm : Page 30 of 51
a 1 20 mm dia Each 30.00 27.00 24 ₹ 639.00
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction
b 2 25 mm dia Each 39.00 35.10 17 ₹ 598.00
c 3 32 mm dia Each 41.00 36.90 14 ₹ 507.00
d 4 40 mm dia Each 45.00 40.50 11 ₹ 446.00
e 5 50 mm dia Each 62.00 55.80 6 ₹ 307.00
f 6 63 mm dia Each 102.00 91.80 3 ₹ 252.00
g 7 75 mm dia Each 159.00 143.10 2 ₹ 236.00

Providing and laying Reducer 8 kg/sq.cm: confirming to IS

5 8.7
specifications.
STEP I
a 2 25 mm dia Each 44.00 39.60 50 ₹ 1,960.00
b 3 32 mm dia Each 49.00 44.10 22 ₹ 970.00
c 4 40 mm dia Each 56.00 50.40 7 ₹ 333.00
d 5 50 mm dia Each 68.00 61.20 4 ₹ 269.00
e 6 63 mm dia Each 93.00 83.70 3 ₹ 276.00
f 7 75 mm dia Each 111.00 99.90 2 ₹ 220.00

Providing butt fusion welded joint/jointing by heating to the ends

with the help of Teflon coated electric mirror/heater ends
6 8.9 together etc. by thermosetting process to HDPE Pipe and
specials. (6kg, 8kg, 10kg) (50mm & above fusion jointed &
below 50mm mechanical jointed)
a 1 20 mm dia Each 59.00 53.10 95 ₹ 5,023.00
b 2 25 mm dia Each 59.00 53.10 68 ₹ 3,621.00
c 3 32 mm dia Each 65.00 58.50 55 ₹ 3,218.00
d 4 40 mm dia Each 79.00 71.10 44 ₹ 3,128.00
e 5 50 mm dia Each 73.00 65.70 22 ₹ 1,445.00
f 6 63 mm dia Each 95.00 85.50 11 ₹ 941.00
g 7 75 mm dia Each 119.00 107.10 7 ₹ 707.00

Providing & Supply of Electro Fusion Tapping Ferrule (Branch

Tapping Saddle) female BSP Threaded with SS 304 insert
fittings in accordance with BS EN 12201 : Part-3 suitable for
drinking water with in black/blue colour manufactured from
compounded PE80/PE 100 virgin polymer and compatible with
7 8.12
PE80/PE100 pipes, in pressure rating SDR 11 with min PN 12.5
rated for water application and shall be inclusive of all cost such
as testing, all taxes related to central, state & municipal,
inspection charges, transportation upto site, transit insurance,
loading, unloading, stacking etc. complete.

a 8.12.1 Electo Fusion Tapping Ferrule Saddle

b 8.12.1.1 63x15mm Each 999.00 899.10 6 ₹ 5,395.00
c 8.12.1.2 63x20mm Each 999.00 899.10 9 ₹ 8,092.00
d 8.12.1.3 63x25mm Each 999.00 899.10 6 ₹ 5,395.00
e 8.12.1.4 75x15mm Each 999.00 899.10 8 ₹ 7,193.00
f 8.12.1.5 75x20mm Each 999.00 899.10 8 ₹ 7,193.00
g 8.12.1.6 75x25mm Each 999.00 899.10 5 ₹ 4,496.00

Providing & Supply of PVC Ball Valves in PN16 rating with one
end compression using Blue colour compression nut in
polypropylene material & other end with female threads
conforming to ISO:4422-4, certified from WRAS UK/KIWA etc.
8 8.14 suitable for food products & drinking water, female threads in
accordance with ISO:7/BS:21/ IS: 554 and shall be inclusive of
all cost such as testing, all taxes related to central, state &
municipal, inspection charges, transportation upto site, transit
insurance, loading, unloading, stacking etc. complete.

a 8.14.1 PVC Ball Valve with Compression & Female Threads

b 8.14.1.1 20x15mm Each 175.00 157.50 50 ₹ 7,796.00
c 8.14.1.2 25x20mm Page 31 of 51 Each 227.00 204.30 22 ₹ 4,495.00
d 8.14.1.3 32x25mm Each 256.00 230.40 9 ₹ 2,028.00
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction
e 8.14.1.4 40x32mm Each 550.00 495.00 7 ₹ 3,267.00
f 8.14.1.5 50x40mm Each 737.00 663.30 4 ₹ 2,919.00
g 8.14.1.6 63x50mm Each 1,133.00 1,019.70 3 ₹ 3,365.00

CHAPTER
C 8.0 MARBLE WORK OTHER THAN FLOORING
(Volume - 2)

Providing and fixing stone slab table rubbed, edges rounded

and polished of size 75x50 cm deep and 1.8 cm thick fixed in
urinal partitions by cutting a chase of appropriate width with
1 8.10 chase cutter and embedding the stone in the chase with
epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 6 mm nominal size) as per
direction of Engineer-in- charge and finished smooth.

2 8.10.2 Granite Stone of approved shade. Sqm 2,824.00 2,541.60 12 ₹ 30,499.00

CHAPTER
D 13 (Volume - REINFORCED CEMENT CONCRETE PIPES
1)
Providing and Laying non-pressure (NP3) RCC socket & spigot
pipes with rubber gasket joint including testing of joints. [
1 13.3
Conforming to IS ;
458-1988, ISI marked laying as per IS 783:1985)
a 150 mm dia Per Meter 376.00 338.40 648 ₹ 2,19,283.00
b 225 mm dia Per Meter 484.00 435.60 408 ₹ 1,77,725.00
c 300 mm dia Per Meter 827.00 744.30 96 ₹ 71,453.00

CHAPTER
E 23 (Volume - BUILDING WATER SUPPLY
2)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply
including all CPVC plane and brass threaded fitting i/c fixing the
1 23.7 pipe with clamps at 1.00 m spacing. This includes jointing of
pipes & fittings with one step CPVC solvent cement and testing
of joints complete as per direction of Engineer in Charge.
Internal work - Exposed on wall.

a 23.7.2 20 mm nominal outer dia .Pipes. Meter 112.00 100.80 25 ₹ 2,520.00

b 23.7.3 25 mm nominal outer dia .Pipes. Meter 140.00 126.00 18 ₹ 2,268.00
c 23.7.4 32 mm nominal outer dia .Pipes. Meter 186.00 167.40 23 ₹ 3,850.00
d 23.7.5 40 mm nominal outer dia .Pipes. Meter 303.00 272.70 251 ₹ 68,393.00
e 23.7.6 50 mm nominal outer dia .Pipes. Meter 436.00 392.40 106 ₹ 41,437.00
DSR Code
f Chlorinated Polyvinyl - chloride (CPVC) pipe 62.5 mm inner dia Meter 1,462.35 1,316.12 297 ₹ 3,90,886.00
No. 8642
DSR Code
g Chlorinated Polyvinyl - chloride (CPVC) pipe 75 mm inner dia Meter 2,051.25 1,846.13 88 ₹ 1,62,459.00
No. 8643
DSR Code
h Chlorinated Polyvinyl - chloride (CPVC) pipe 100 mm inner dia Meter 2,834.00 2,550.60 15 ₹ 38,259.00
No. 8644

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply
including all CPVC plain & brass threaded fittings i/c fixing the
pipe with clamps at 1.00 m spacing. This includes jointing of
2 23.8
pipes & fittings with one step CPVC solvent cement and the cost
of cutting chases and making good the same including testing of
joints complete as per direction of Engineer in Charge. Concealed
work including cutting chases and making good the walls etc.

a 23.8.2 20 mm nominal outer dia .Pipes. Meter 175.00 157.50 165 ₹ 25,988.00
Page 32 of 51
b 23.8.3 25 mm nominal outer dia .Pipes. Meter 213.00 191.70 198 ₹ 37,957.00
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction
c 23.8.4 32 mm nominal outer dia .Pipes. Meter 266.00 239.40 418 ₹ 1,00,069.00
₹ 0.00
3 23.16 Providing and fixing brass stop cock of approved quality : ₹ 0.00
a 23.16.1 15 mm nominal bore 0.40kg Each 224.00 201.60 12 ₹ 2,419.00
b 23.16.2 20 mm nominal bore 0.75kg Each 268.00 241.20 27 ₹ 6,512.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply
including all CPVC plain & brass threaded fittings This includes
4 23.9 jointing of pipes & fittings with one step CPVC solvent cement
,trenching ,refilling & testing of joints complete as per direction
of Engineer in Charge.
External work
a 23.9.5 40 mm nominal outer dia .Pipes. Meter 1,346.00 250.20 25 ₹ 6,255.00
b 23.9.7 62.50 mm nominal inner dia Pipes. Meter 1,346.00 1,211.40 407 ₹ 4,93,040.00
c 23.9.8 75 mm nominal inner dia .Pipes. Meter 1,756.00 1,580.40 165 ₹ 2,60,766.00

Providing and fixing gun metal gate valve with C.I. wheel of
5 23.17 approved
quality (screwed end):
a 23.17.4 32 mm nominal bore. Each 121.00 4 ₹ 484.00
b 23.17.4 32 mm nominal bore. Each 373.00 335.70 20 ₹ 6,647.00
c 23.17.5 40 mm nominal bore Each 493.00 443.70 6 ₹ 2,440.00
e 23.17.6 50 mm nominal bore Each 744.00 669.60 14 ₹ 9,575.00
f 23.17.7 65 mm nominal bore Each 1,401.00 1,260.90 6 ₹ 6,935.00
g 23.17.8 80 mm nominal bore Each 2,199.00 1,979.10 2 ₹ 4,354.00

Providing and fixing ball valve (brass) of approved quality, High

6 23.18 or low
pressure, with plastic floats complete :
a 23.18.1 15 mm nominal bore Each 250.00 225.00 20 ₹ 4,455.00
b 23.18.2 20 mm nominal bore Each 365.00 328.50 22 ₹ 7,227.00
c 23.18.3 25 mm nominal bore Each 423.00 380.70 18 ₹ 6,700.00

Providing and fixing gun metal non- return valve of approved

7 23.19 quality
(screwed end) :
a 23.19.4 50 mm nominal bore
b 23.19.4.2 Vertical Each 973.00 875.70 3 ₹ 2,627.00

Providing and fixing C.P. brass shower rose with 15 or 20 mm

8 23.19
inlet :
a 23.22.2 150 mm diameter Each 776.00 698.40 54 ₹ 37,714.00

Providing and placing on at all floor levels high design HDPE

(polyethylene) water storage tank ISI : 12701 marked with cover
and suitable locking arrangement and making necessary holes for
9 23.28 Ltr 6.30 5000 ₹ 31,500.00
inlet, outlet and arrangement and making necessary holes for
inlet, outlet and overflow pipes but without fittings and the base
support for tank.

Providing and fixing C.P. brass bib cock of approved quality

10 23.29 conforming to
IS:8931
a 23.29.1 15 mm nominal bore. Each 360.00 324.00 60 ₹ 19,440.00

Providing and fixing C.P. brass wall mixer of approved quality

11 23.36
and make conforming to IS: specification.
a 23.36.1 15 mm nominal bore. Each 2,053.00 1,847.70 54 ₹ 99,776.00

Providing and fixing C.P. brass stop cock (concealed) of standard

12 23.32 Page 33 of 51
design and of approved make conforming to IS:8931.
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction
a 23.32.1 15 mm nominal bore. Each 360.00 324.00 35 ₹ 11,340.00

Providing and fixing C.P. brass angle valve for basin mixer and
13 23.33 geyser
points of approved quality conforming to IS:8931
a 23.33.1 15 mm nominal bore Each 401.00 360.90 74 ₹ 26,707.00
Providing and fixing C.P. brass grating of approved quality and
14 23.38 make
conforming to IS: specification.
a 23.38.1 100 mm dia. Each 44.00 39.60 253 ₹ 10,019.00

Providing and fixing C.P. brass soap container 109 mm wide,125

high and 112 mm distance from wall of standard shape with
15 23.39 bracket of the same material with all fittings etc. of approved nos 587.00 528.30 60 ₹ 31,698.00
quality and make like Jaguor or equivalent conforming to
IS:specification.

Providing and fixing C.I. double acting air valve of approved

quality with bolts, nuts, rubber insertions etc. complete (The tail
16 23.45
pieces, tapers etc if
required will be paid separately) :
a 23.45.1 50 mm dia Each 2,124.00 1,911.60 6 ₹ 10,514.00

Providing and fixing enclosed type water meter (bulk type)

conforming to IS 2373 and tested by Engineer in charge complete
17 23.48
with bolts & nuts rubber insertions etc.(the tail pieces if required
will be paid separately)
a 23.48.1 80 mm dia nominal bore Each 2,688.00 2,419.20 2 ₹ 4,838.00

Providing and fixing C.I. dirt box strainer for bulk type water
18 23.49 meter with bolts & nuts rubber insertions etc.complete
conforming to IS 2373 :
a 23.49.1 80 mm dia nominal bore Each 3,424.00 3,081.60 2 ₹ 6,163.00

Constructing one brick masonry chamber 30x30x50 cm inside,

with 25 class designation modular brick work in cement mortar
1:4 (1 cement : 4 coarse sand) for stop cock,with C.I. surface box
100x100x75 mm (inside) with hinged cover fixed in slab of
cement concrete grade M-20 (Nominal Mix with 20mm
19 23.51 Each 5,565.00 5,008.50 85 ₹ 4,27,225.00
maximum size of stone aggregate) necessary excavation 75 mm
thick foundation concrete grade M-7.5 (Nominal Mix with 40mm
maximum size of stone aggregate) & inside plastering with
cement mortar 1:3 (1 cement : 3 sand) 12 mm thick finished with
a floating coat of neat cement complete as per standard disign :

Constructing one brick masonry chamber 60x45x50 cm inside,

with 40 class designation brick work in cement mortar 1:4 (1
cement : 4 coarse sand) for water meter complete with C.I.
double flap surface box 400x200x200 mm (inside) with locking
arrangement. RCC top slab of cement concrete grade M-20
20 23.55 (Nominal Mix with 20mm maximum size of stone aggregate) Each 5,071.00 4,563.90 18 ₹ 83,519.00
along with necessary excavation, 100mm thick foundation
concrete grade M-7.5 (Nominal Mix with 40mm maximum size
of stone aggregate) and inside plastering with cement mortar 1:3
(1 cement : 3 coarse sand) 12 mm thick finished with a floating
coat of neat cement complete as per standard design.

Page 34 of 51
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction
CHAPTER-
F 24 (Volume - BUILDING DRAINAGE
2)

Providing and fixing square-mouth S.W. gully trap grade 'A'‟

complete with C.I. grating brick masonry chamber with water
tight
1 24.1 C.I. cover with frame of 300 x300 mm size (inside) the weight of
cover to be not less than 4.50 kg and frame to be not less than
2.70 kg as per standard design : With Modular Bricks class
designation 40.

a 24.1.2 150 x 100 mm size P type. Each 1,393.00 1,253.70 42 ₹ 52,655.00

Constructing brick masonry moudlar brick class designation 40

manhole in cement mortar 1:4 (1 cement : 4 sand ) R.C.C. top
slab with Cement concrete grade M-20 (Nominal Mix with
20mm maximum size of stone aggregate), 20 cm thick
foundation concrete grade M-7.5 (Nominal Mix with 40mm
2 24.4 maximum size of stone aggregate) inside plastering 12mm thick
with cement mortar 1:3 (1 cement : 3 sand) finished with floating
coat of neat cement and making channels in cement concrete
grade M-15 (Nominal Mix with 20mm maximum size of stone
aggregate) as per standard design. The sizes of manhole and
manhole covers as detailed below.

Manhole inside size 90x80 cm and 45 cm deep including C.I.

cover with frame (light duty) 455x610 mm internal dimensions
a 24.4.1 Each 7,377.00 6,639.30 32 ₹ 2,12,458.00
total weight of cover and frame to be not less than 38 kg (weight
of cover 23 kg and weight of frame 15 kg) :

Inside size 120x90 cm and 90 cm deep including C.I. cover with

frame (heavy duty) 560 mm internal diameter, total weight of
b 24.4.3 cover and frame to be not less than 208 kg (weight of cover 108 Each 20,521.00 18,468.90 59 ₹ 10,89,665.00
kg and
weight of frame 100 kg)

Extra for depth for manholes. With Modular bricks class

3 24.5
designation 40
a 24.5.1 Size 90x80 cm meter 4,881.00 4,392.90 8 ₹ 35,143.00
b 24.5.2 Size 120x90 cm meter 5,840.00 5,256.00 13 ₹ 68,328.00

Making connection of drain or sewer line with existing manhole

including breaking into and making good the walls, floors with
cement concrete grade M-15 (Nominal Mix with 20mm
4 24.9 maximum size of stone aggregate) cement plastered on both sides
with cement mortar 1:3 (1 cement : 3 sand) finished with a
floating coat of neat cement and making necessary channels for
the drain etc. complete :
a 24.9.1 For pipes 100 to 250 mm diameter Each 201.00 180.90 2 ₹ 362.00
b 24.9.2 For pipes 250 to 300 mm diameter Each 261.00 234.90 3 ₹ 705.00
c 24.9.3 For pipes 350 to 450 mm diameter Each 392.00 352.80 3 ₹ 1,058.00

Constructing brick masonry road gully chamber 50x45x60 cm

with bricks of class designation 40 in cement mortar 1:4 (1
5 24.10 cement : 4 sand) including 500x450 mm pre-cast R.C.C.
horizontal grating with frame (minimum weight of grating 75 kg)
complete as per standard design :
a 24.10.1 With Modular bricks Each 3,258.00 2,932.20 42 ₹ 1,23,152.00

Providing and fixing S.W. intercepting trap in manholes with

6 24.12 stiff mixture of cement mortar 1:1 (1 cement : 1 finePage
sand)35 of 51
including testing of joints etc. complete :
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction
a 24.12.2 150 mm dia Each 334.00 300.60 5 ₹ 1,503.00

Providing and laying below ground unplasticised PVC pipe to

with stand working pressure of 4 kg/cm2 soild waste pipes
7 24.13 confirming to IS:13592 and IS:4985 including jointing with seal
ring confirming to IS :5282 leaving 10mm gap for thermal
expansion all necessary fittings etc. complete.
a 24.13.1 110 mm diameter OD Each 159.00 143.10 473 ₹ 67,686.00
b 24.13.2 160 mm diameter OD Each 353.00 317.70 35 ₹ 11,120.00

Providing and fixing unplasticised Rigid PVC soil and waste

17.58
pipes confirming to IS: 13592 Type B including jointing with
8 (MP PWD
seal ring confirming to IS:5382 leaving 10 mm gap for thermal
SOR)
expansion Single socket pipes for working pressure of 4kg/sqcm.

a 17.58.1 75 mm diameter (minimum wall thickness 3.2mm) Each 136.00 122.40 39 ₹ 4,774.00
b 17.58.2 110 mm diameter (minimum) wall thickness 3.2mm) Each 238.00 214.20 55 ₹ 11,781.00

DSR SOR Providing and fixing P.V.C. waste pipe for sink or wash basin
9
17.28 including PVC. waste fittings complete.
DSR SOR
a Semi rigid pipe
17.28.1
DSR SOR
b 40 mm dia Each 82.60 74.34 155 ₹ 11,523.00
17.28.1.2

CHAPTER
G 25 (Volume - SANITARY INSTALLATIONS
2)

Providing and fixing water closet squatting pan (Indian type

W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low
level white P.V.C. flushing cistern with manually controlled
1 25.1
device (handle lever) conforming to IS : 7231, with all fittings
and fixtures complete including cutting and making good the
walls and floors wherever required :

White Vitreous china Orissa pattern W.C. pan of size

a 25.1.1 Each 2,698.00 2,428.20 11 ₹ 26,225.00
580x440mm with integral type foot rests
Providing and fixing white vitreous china pedestal type water
closet (European type) with seat and lid, 10 litre low level white
vitreous china flushing cistern & C.P. flush bend with fittings &
C.I.brackets, 40mm flush bend, overflow arrangement with
2 25.3 specials of standard make and mosquito proof coupling of
approved municipal design complete including painting of
fittings and brackets, cutting and making good the walls and
floors wherever required :
a 25.3.1 W.C. pan with ISI marked white solid plastic seat and lid. Each 3,823.00 3,440.70 46 ₹ 1,56,896.00
Providing and fixing white vitreous china flat back half stall
urinal of size 580x380x350mm with white PVC automatic
flushing cistern, with fittings, standard size C.P. brass flush pipe,
spreaders with unions and clamps (all in C.P. brass) with waste
3 25.5 fitting as per IS : 2556, C.I. trap with outlet grating and other
couplings in C.P. brass including painting of fittings and cutting
and making good the walls and floors wherever required :

Single half stall urinal with 5 litre P.V.C. automatic flushing

a 25.5.1 Each 4,422.00 3,979.80 32 ₹ 1,27,354.00
cistern.
Providing and fixing wash basin with C.I. brackets, 15 mm C.P.
brass pillar taps,32 mm C.P. brass waste of standard pattern,
4 25.7
including painting of fittings and brackets, cutting and making
good the walls wherever require :
White Vitreous China Flat back wash basin size 550x400 mm
a 25.7.4 with Page 36 of 51 Each 1,223.00 1,100.70 60 ₹ 66,042.00
single 15 mm C.P. brass pillar tap
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction

Providing and fixing kitchen sink with C.I. brackets, C.P. brass
chain with rubber plug, 40 mm C.P. brass waste complete,
5 25.9
including painting the fittings and brackets, cutting and making
good the walls wherever required :

a 25.9.1 White glazed fire clay kitchen sink of size 600x450x250mm. Each 2,091.00 1,881.90 6 ₹ 11,291.00

Providing and fixing white vitreous china water closet squatting

6 25.13
pan (Indian type)
a 25.13.2 Orissa pattern W.C. pan of size 580x440 mm Each 1,067.40 5 ₹ 5,337.00

Providing and fixing mirror of superior glass (of approved

quality) and of required shape and size with plastic moulded
7 25.32
frame of approved make and shade with 6 mm thick hard board
backing :
a 25.32.2 Rectangular shape 453x357mm Each 616.50 60 ₹ 36,990.00

8 25.34 Providing and fixing toilet paper holder :

a 25.34.2 Vitreous China Each 212.00 190.80 56 ₹ 10,685.00

Providing and fixing white vitreous china squatting plate urinal

9 25.24 Each 1,265.00 1,138.50 25 ₹ 28,463.00
with integral rim longitudinal flush pipe.

Providing and fixing a pair of white vitreous china foot rests of

10 25.17
standard pattern for squatting pan water closet:
a 25.17.1 250x130x30 mm Pair 118.80 5 ₹ 594.00

Providing and fixing G.I. inlet connection for flush pipe

11 25.22 Each 76.50 5 ₹ 383.00
connecting with W.C. pan.

Providing and fixing P.V.C. waste pipe for sink or wash basin
12 25.28
including P.V.C. waste fittings complete.
a 25.28.2 Flexible pipe
i 25.28.2.1 32mm dia Each 48.60 5 ₹ 243.00

13 25.35 Providing and fixing soil, waste and vent pipes :

a 25.35.1 100 mm dia
i 25.35.1.1 Sand cast iron S&S pipe as per IS : 1729 meter 477.90 15 ₹ 7,169.00

17.72
Providing and fixing CP Bottle trap of approved quality & make
14 (MP PWD Each 853.00 767.70 66 ₹ 50,668.00
for sink & wash basin
SOR)

17.75
Providing and fixing CP Brass Soap dish of approved quality and
15 (MP PWD Each 422.00 379.80 60 ₹ 22,788.00
make
SOR)

25.37 Providing & fixing in position best indian Health Facuets 8mm
16 (MP PWD dia 1 meter long flaxible tube and wallv bracketwith N.R.V. (non Each 1,920.00 1,728.00 56 ₹ 97,459.00
SOR) returnm wall)

25.51 Providing & fixing in position best Indian C.P. Brass made (0.3
17 (MP PWD micron Chrome and 10 micron Nickel Plated) Single Towel Rail Each 2,520.00 2,268.00 54 ₹ 1,22,472.00
SOR) 600 mm long.

25.53
Providing and fixing best Indian C. P. Brass made (0.3 micron
18 (MP PWD Each 1,920.00 1,728.00 66 ₹ 1,14,048.00
chrome and 10 micron Nickel plated) Single Towel Ring Square.
SOR) Page 37 of 51
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction

Providing and fixing trap of self cleansing design with screwed

19 25.60 down or hinged grating with or without vent arm complete,
including cost of cutting and making good the walls and floors :

a 100 mm inlet and 100 mm outlet

i Sand cast iron S & S as per IS: 3989. Each 637.00 573.30 253 ₹ 1,45,045.00

Supply, installation, testing & commissioning storage type

electronic water Geyser. Storage tank should be covered with
20 NON SOR corrosion resistant insulation material & power rating should
have 3 to 5 star. including providing and fixing stop cock, Non-
return valve, and safety valve connections.

a NON SOR Geyser 15 Ltr Capacity Each 6,500.00 4 ₹ 26,000.00

b NON SOR Geyser 25 Ltr Capacity Each 7,800.00 8 ₹ 62,400.00
₹ 0.00
H NON SOR SUBMERSIBLE OPENWELL PUMPS:

Supply, installation, testing & commissioning of Submersible

single/ Multi stage single entry openwell pumps connected to
submersible motor with 400/ 415 +/-10% volts, 3 phase 50 Hz
1 NON SOR A.C. power supply & 2900 RPM with double mechanical seal,, in Nos 6 ₹ -
built level controller with operational mode as pump starts at low
water level in OHT, both pumps at the same time during peak
with a Hooter alarm and cut off at dry level as determined.

The pump shall be provided with a lifting devise of pull chain &
2 NON SOR G.I. heavy class rising main of 7.5m length including Nos 6 ₹ -
interconnecting piping
Submersible pump connector unit with rubber diaphragm and
bend, vertical Flexible discharge pipe with required
3 NON SOR Nos 6 ₹ -
unions/flanges and 15 m cable etc. as per requirement complete
in all respects.

Electrical Starter panels complete with O/L Relay with Single

phasing preventer feature, earth leakage relay, ON-OFF and Trip
Indicating lamps, contactors contacts for Building Automation
System, interlocking, level controller with operational mode as
one pump working at low level, both pumps at high level with a
4 NON SOR hooter alarm and cut off at dry level and capable to communicate Nos 3 ₹ -
with BMS System through potential free contacts for indication
of pump On/Off/Trip with provision of remote on/off.t, cascade
operation, working / standby selection, etc. suitable for the motor
H.P. as specified below and with provision for remote P.B.
on/off complete as required.

Set of accessories such as CPVC Header discharge header

5 NON SOR Isolation/Butterfly/Ball valves, non return valves,inter connecting Set 3 ₹ -
power and control cabling etc.
All accessories shall be in vendor's scope and the relevant quotes
shall be submitted by the vendors
6 NON SOR Capacity per pump 15 m3/hour 30 mtr Head (1 Set = 1 W+1SB) Set 1,04,500.00 3 ₹ 3,13,500.00

7 NON SOR Capacity per pump 10 m3/hour 40 mtr Head (1 Set = 1 W+1SB) Set 1,23,000.00 3 ₹ 3,69,000.00

I NON SOR RO PLANT WITH WATER COOLER & RELATED ACCESSORIES

Page 38 of 51
 3. PLUMBING WORK

UADD SOR UADD Rate after 10%

S No. Discription of Item UOM Qty Amount
Vol II SOR Rate Deduction

Supply, installation, testing & commissioning of skid mounted

fully Automatic Reverse Osmosis of output capacity 20 LPH
with appropriate thickness designed at a minimum Flux at inlet
and necessary recovery: With Centralized Water Coolers of SS
1 Non SOR Set 74,000.00 2 ₹ 1,48,000.00
304 MOC with 40 LPH cooling capacity with inbuilt storage
capacity as per system with insulation of required thickness & of
appropriate material and with power supply of 220/ 230+/-10%
volts, 1 phase 50 Hz A.C. supply

Supply, installation, testing & commissioning of skid mounted

fully Automatic Reverse Osmosis of output capacity 40 LPH
with appropriate thickness designed at a minimum Flux at inlet
and necessary recovery: With Centralized Water Coolers of SS
2 Non SOR Set 1,07,000.00 2 ₹ 2,14,000.00
304 MOC with 80 LPH cooling capacity with inbuilt storage
capacity as per system with insulation of required thickness & of
appropriate material and with power supply of 220/ 230+/-10%
volts, 1 phase 50 Hz A.C. supply

H NON SOR BOOSTER PUMP

Supply, installation, testing & commissioning of In-line,

multistage, centrifugal clear water pumps, speed upto 2900
rpm with SS-304 Casing/Sleeve, SS 304 Impeller and SS-304
Shaft, C.I. Base CED coating & head connected to a TEFC
motor (with mechanical seal) suitable for 400/ 415+/-10% volts,
3 phase 50 cycles A.C. supply with common CPVC suction &
Non SOR Nos 8
discharge header & pipe connections including pump base in
hot dipped galvanizing only with vibration eliminating pads
as required,Pressure vessele or tank & complete shall be in
vendors scope. Vendor to submit performance curves and
technical catalogue of the proposed model for review and
information.

Compound gauge (In tolerance -1 to +1) in SS glycerine filled

Non SOR Nos 4
and 4 inch dial connection along with bottom thread
Set of accessories such as Isolation/ Butterfly/ Ball valves, non
Non SOR return valves, pressure transducers, inter connecting power and Set 4
control cabling etc.

The offer shall be inclusive of the starter panel with auto on/off
& level controller for automatic operation of the pumps. The
Non SOR Nos 4
logics of the pump operation shall be matched with high level &
low level of the OH water tanks & pressure sensing

All accessories shall be in vendor's scope and the relevant

Non SOR
quotes shall be submitted by the vendors

Non SOR Capacity per pump 8 m3/hour 15 mtr Head (1 Set = 1 W+1SB) Set 4 ₹ 6,60,000.00

TOTAL COST ₹ 77,66,681.00

Page 39 of 51
 4. ICT COMPONENT

Sr.No. Discription of Item Unit Rate Qty Amount

3 MP (20 fps) and Full HD 1080p (25/30 fps) image with 1/3"" 3 MP sensor, true
widescreen image on a 16:9 display, 12.5% more horizontal pixel density than
conventional 3 MP 4:3 (2048×1536) cameras IR LEDs provide up to 30 m (100 ft) of
illumination in dimly lit or nighttime scenes.
• Smart IR technology for even distribution of IR • Waterproof (IP66) and IK10 vandal
resistant camera housing
• Small form factor, inconspicuous after installation
1 • 2.7–12 mm F1.4 motorized focus/zoom lens and 2.8 mm F2.1 fixed lens provide Nos 25845 24 ₹ 6,20,280.00
wide range of field of view options
• Monitor from anywhere using HonView Touch mobile app for both Apple® and
Android™ smart phones and tablet computers
• Configurable motion detection and camera tamper detection settings,
including configurable
alarm notifications"

3 MP IR LEDs provide up to 30 m (100 ft) of illumination in dimly lit or nighttime

scenes • Smart IR technology for even distribution of IR•
Waterproof (IP66) camera housing is perfect for outdoor installations • 2.7–12 mm
F1.4 motorized focus/zoom lens and 3.6 mm F2.1 fixed lens
2 provide wide range of field of view options Nos 25845 8 ₹ 2,06,760.00
• Monitor from anywhere using HonView Touch mobile app for both Apple® and
Android™ smart phones and tablet computers
• Configurable motion detection and camera tamper detection settings, including
configurable
alarm notifications.
Network Video Storage : 16CH @ 1080P / 4K NVR, 8 HDDs max 64TB, RAID, Hot
3 Swap, 1 SAS, 2 1000M Ports, ONVIF. Nos 140000 2 ₹ 2,80,000.00

6TB Enterprise HDD for video surveillence applications. Make :

4 Nos 20500 2 ₹ 41,000.00
WDAV/Seagate/Toshiba
32” LED Display with necessary connectors , inter linking cords etc. complete as
5 Nos 57000 2 ₹ 1,14,000.00
required .Make : Samsung/LG/Sony
6 Nos 4174 2 ₹ 8,348.00
24 Port CAT6a patch Panels Un-Loaded, etc. complete as required
7 Nos 723 64 ₹ 46,272.00
CAT6a RJ 45 I/O for Voice Yellow Color at Rack Side
CAT6a UTP PATCH CORD 1 Meter - Blue for Rack side etc.
8 complete as required. Nos 872 32 ₹ 27,904.00

9 CAT6a UTP PATCH CORD 2 Meter etc. complete as required Nos 32 ₹ 0.00
14 U Rack including providing & fixing of trays and fixing of
10 Apparatus/ NVRs inside the rack Make: Elixir/D-Link/Netrack/Rittal Nos 35000 1 ₹ 35,000.00

11 Power Cable 2corex1.5 sq mm flexible cable for cameras Mtr 80 1000 ₹ 80,000.00

12 4-pair, CAT6a UTP Cable LSZH ;4 twisted pairs of 23 AWG solid conductors; etc. Mtr 72 2000 ₹ 1,44,000.00
complete as required. Make: Amp/Panduit/Systimax/Schneider
13 24port POE plus network Swtich . Make: CISCO/HP Nos 65908 1 ₹ 65,908.00

14 6 Core Single Mode Fiber Optic Cable. Make: Amp/D-Link Mtr 92 200 ₹ 18,400.00

15 Media Converter 10/100/1000 mbps.Make: D-Link/TP-Link/Digisol Nos 12450 1 ₹ 12,450.00

16 Unloaded LIU for the converter Nos 4560 1 ₹ 4,560.00

Total Cost ₹ 17,04,882.00
 5. AIR CONDITIONER

SOR No.
Sr.no. Discription of Item Unit Rate Qty Amount
2018
SPLIt AC(Inverter) Supply,Installtion,Testing and
Commissioning of Split type wall mounted Air
Conditioning Unit of following capacity including
outdoor and indoor unit fitted with inverter based
rotary compressor ,copper condensor and first
charge refrigerant R410 A.The condensing unit
working range should be capable of providing
1 46.11 cooling between +/- 5 degree .C to 50 degree.C &
heating with in 0 deg.C to 15 deg.C.Including
connection of copper pipe of required size upto 3
mtr.Insulation ,Cordless remote control,auto air
swing louvers,wall stand for outdoor
unit,connection copper lead wire,condensed water
outlet pipe 2 mtr complete etc as required
.outdoor/Indoor unit shold be of same make(Brand)
1 TR Sta Rating 5 Star
a 46.11.2 Each 43340 6 ₹ 2,60,040.00
b 46.11.4 1.5 TR Start Rating 5 Star Each 59142 1 ₹ 59,142.00
c 46.11.6 1.8/2 TR start Rating 5 Star Each 75826 4 ₹ 3,03,304.00
Cassate AC:Supply,installation,testing and
commissioning of Split type ceilling cassate slim
line /Floor standing Air Conditionning unit of
capacity including indoor,outdoor unit fitted with
rotary commressor ,copper condensor and first
charge R410A /Eco friendly green gas only cordless
2 46.13 remote control ,auto air swing louvers,connection
copper lead wire between outdoor and indoor unit
,connecction copeper lead wire upto 1.5 mtr
,excluding connection copper pipe of required size
insulation,floor stand for outdoor unit ,condense
water outlet complete etc as required outdoor
/indoor unit shoulf be same make(brand)
Ceilling suspended/Mounted cassate type 4 way unit
a 46.13.1 with inbuilt drain pump and decorative panel.

i 46.13.1.1 1.8 /2.0 TR Single Phase Each 86198 19 ₹ 16,37,762.00

ii 46.13.1.3 2.7/3TR Three Phase Each 125091 4 ₹ 5,00,364.00
Supply,installation ,testing and commissioing of
suction/discharge copper pipe line in split
3 46.3 AC/Cassate AC unit 1.0/1.5/2/3 TR capacity
including brazing,nitrile rubber insulation 6/9 mm
thick,class Ó etc complete as required.
a 46.3.1 Copper tube 1/4" Rm 310 550 ₹ 1,70,500.00
b 46.3.2 Copper tube 3/8 Rm 390 500 ₹ 1,95,000.00

Page 41 of 51
 5. AIR CONDITIONER

SOR No.
Sr.no. Discription of Item Unit Rate Qty Amount
2018
c 46.3.3 Copper tube 1/2 Rm 470 100 ₹ 47,000.00
d 46.3.4 Copper tube 5/8 Rm 559 100 ₹ 55,900.00
PVC Fresh Air Pipe Fan:-Supply anf fixing of PVC
fresh air pipe/Exhaust pipe with all required
4 46.3
accessories and hardware for ceilling suspended.

46.30.2 150mm Dia RM 276 100 ₹ 27,600.00

Refrigerant:Supply and additional refrigerant
R410/R410A to compensate the additional piping
4 46.31 KG 750 50 ₹ 37,500.00
done at site for all system including testing
commissioning as required
Flexible Connectin:-Providing and fixing of flexible
canvas connection between exhaust pipe and
46.37 Each 1794 4 ₹ 7,176.00
exhaust fan at terrace to avoide vinbration and
transfer air.
Control Cable:Supply and laying,testing and
commissioning of following size of copper
conductor control cables on existing tray/Surface
5 46.38 including fixing clamps and proper connections to
equipments etc complete as required.

a 46.38.12Cx.75 Sqmm Mtr 30 1000 ₹ 30,000.00

b 46.38.34Cx2.5 Sqmm Mtr 89 100 ₹ 8,900.00
c 46.38.54Cx6sqmm Mtr 199 500 ₹ 99,500.00
Supply and installtion of alluminium powder coated
NOS SOR RA grill of approved shade and make in accordance
with approved specification
a 300x300MM Nos 750 24 ₹ 18,000.00
Total Cost ₹ 34,57,688.00

Page 42 of 51
 6. ROAD WORK

After
Sl. SOR Item UADD
Discription of Item Unit 10% Rate quantity Amount
No. No. SOR Rate
Deduction

Excavation for roadway in soil including loading in truck for carrying of

1 3.1 cut earth to embankment site with all lifts and lead upto 1000 meters Cum 98 88.20 6071.175 ₹ 5,35,478.00
and as per relevant clauses of section-300.
Construction of Embankment/Sub grade/ earth shoulders, as per clause
305.1.1 inclusive of operation necessary as per clause 305 & its sub-
clauses, Where required but with approved materials obtained from
excavation for road construction (vide clause 301.3.11) i/c consolidating
the original ground by rolling as directed by the Engineer-in-charge but
2 3.9 with a maximum of 6 passes of 8-10 tonne roller & i/c compaction and Cum 234 210.60 1902.6 ₹ 4,00,688.00
maintenance of surface during construction to ensure shedding &
preventing ponding of water (clause 305.3.7), finishing i/c all lifts but
excluding scarifying existing granular/bituminous road surface vide
clause 305.6.

Construction of granular sub-base by providing coarse graded material,

spreading in uniform layers with on prepared surface, mixing by mix in
4.1 place method at OMC, and compacting with vibratory roller to achieve 0
3
the desired density, complete in all respect and as per relevant clauses of
section-400.
ii) with crushed stone for grading-II Material Cum 614 552.60 1335.15 ₹ 7,37,804.00
Construction of dry lean cement concrete Sub-base over a prepared sub-
grade with coarse and fine aggregate conforming to IS: 383, the size of
coarse aggregate not exceeding 25mm, aggregate cement ratio not to
exceed 15:1, aggregate gradation after blending to be as per table of
MORTH Specifications 600-1, cement content not to be less than 200
kg/cum, optimum moisture content to be determined during trial length
4 6.1 construction, concrete strength not to be less than 10 Mpa at 7 days, Cum 2886 2597.40 859.5 ₹ 22,32,465.00
mixed in a batching plant, transported to site, laid with paver with
electronic sensor/mechanical paver, compacting with 8-10 tonnes
vibratory roller, finishing and curing and as per relevant clauses of
section-603.

Deduct from Item No.6.1 above if paver with Electronic sensor,

5 6.2 vibratory roller are not used and laying, compaction is done by any other Cum 190 171.00 0
method.
Construction of dowel jointed, plain cement concrete pavement in M-40
grade concrete over a prepared sub base with 43 or higher grade cement,
maximum size of coarse aggregate not exceeding 25 mm, mixed in a
batching and mixing plant as per approved mix design, transported to
site, laid with a fixed form or slip form paver with electronic sensor,
spread, compacted and finished in a continuous operation including
provision of contraction, expansion, construction and longitudinal joints,
6 6.3 joint filler, separation membrane, sealant primer, joint sealant, Cum 4792 4312.80 1566 ₹ 67,53,845.00
debonding strip, placing of dowel bar and tie rod, admixtures as
approved, curing compound, finishing to lines and grades as per
approved drawings as per IRC-15 2002 and as per relevant clauses of
section-602 of of MORTH specifications complete but excluding cost of
steel in dowel bar & tie rod etc..

Deduct from Item No.6.3 above if paver with electronic sensor is not
used and laying, compaction is done by any other method (The
acceptance criteria regarding level, thickness, surface regularity, texture
7 6.4 finish, strength of concrete and all other quality control measures shall Cum 335 301.50 0
be the same as in case of machine laid work.)

Add extra in Item No.- 6.3 & 6.5 above for the cost of stell in dowel bar
6.12 0
and tie rod etc. required as per design.
8
6.12.1 Mild Steel dowel bars (0.500mtr long, 25 mm dia, 300mm c/c) MT 47850 43065.00 11.1882716 ₹ 4,81,823.00
6.12.2 Tor steel tie rod (0.700mtr long, 12mm dia, - 500mm c/c) MT 52800 47520.00 3.63636 ₹ 1,72,800.00

43 of 51
 After
Sl. SOR Item UADD
Discription of Item Unit 10% Rate quantity Amount
No. No. SOR Rate
Deduction

Construction of cement concrete kerb with top and bottom width 115
and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10
grade foundation 150 mm thick, foundation having 50 mm projection
9 8.1 beyond kerb stone, kerb stone laid with kerb laying machine, foundation Meter 187 168.30 3060 ₹ 5,14,998.00
concrete laid manually, all complete and as per clause 408 of
specifications.
Using Concrete Mixer
Providing and fixing of retro- reflectorised cautionary, mandatory and
informatory sign as per IRC :67 made of encapsulated lens type
reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5
mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6
mm (height from crown level of the road and bottom of the sign board
8.3 shall not be less than 1.5 m.) firmly fixed to the ground by means of
10 properly designed foundation with M15 grade cement concrete 45 cm x
45 cm x 60 cm, 60 cm below ground level as per approved drawing
including painting of vertical post as per specification.

i) 90 cm equilateral triangle Each 3715 3343.50 19.8 ₹ 66,201.00

iii) 60 cm circular Each 3291 2961.90 19.8 ₹ 58,646.00
v) 60 cm x 45 cm rectangular Each 3209 2888.10 19.8 ₹ 57,184.00
Painting two coats after filling the surface with synthetic enamel paint in
all shades on new plastered concrete surfaces and as per relevant clauses
11 8.6 sqm 44 39.60 1224 ₹ 48,470.00
of section-800 & I.R.C.-67 including cost of paint etc. complete.

Road Marking with Hot Applied Thermoplastic Compound with

Reflectorising Glass Beads on Bituminous Surface (Providing and
laying of hot applied thermoplastic compound 2.5 mm thick including
12 8.10 reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm sqm 900 810.00 610.02 ₹ 4,94,116.00
is exclusive of surface applied glass beads as per IRC:35 .The finished
surface to be level, uniform and free from streaks and holes and as per
relevant clauses of section-800.
Providing chute drain consisting of NP-2 R.C.C. half round pipe, laid
over block of C.C. 1:3:6 (20mm and down aggregate size 450x265mm
8.25 laid over filter media (measured and paid separately) i/c all false work
13
etc. complete

(a) 300mm dia RM 340 306.00 114.75 ₹ 35,114.00

Providing and laying 100 mm thick factory made cement concrete
11.46.2 interlocking paver block of M -30 grade made by block making machine
(Volume 2 with strong vibratory compaction and of approved size and design/
14 Building shape laid in required colour and pattern over and including 50mm sqm 678 610.20 1147.5 ₹ 7,00,205.00
Works SSR thick compacted bed of course sand, filling the joints with coarse sand
2012) etc. all complete as per the direction of Engineer-in-charge.

Drain Below Padestrain

Providing and laying reinforced cement concrete pipe 300mm dia NP-4
for service ducts.
Providing and laying of a reinforced cement concrete pipe duct, 300 mm
dia, across the road (new construction), extending from drain to drain in
cuts and toe of slope to toe of slope in fills, constructing head walls in
cement mortar 1:3 at both ends, providing a minimum fill of granular
6.9 material over top and sides of RCC pipe as per IRC:98-1997, bedded on
15 a 0.3 m thick layer of granular material free of rock pieces, outer to outer
distance of pipe at least half dia of pipe subject to minimum 450 mm in
case of double and triple row ducts, joints to be made leak proof, invert
level of duct to be above higher than ground level to prevent entry of
water and dirt, all as per IRC: 98 - 1997 and approved drawings

6.9.1 Single row for one utility service Meter 1230 1107.00 783 ₹ 8,66,781.00

44 of 51
 After
Sl. SOR Item UADD
Discription of Item Unit 10% Rate quantity Amount
No. No. SOR Rate
Deduction

Earth work in excavation of foundation of structures as per drawing and

technical specification, including setting out, construction of shoring
and bracing, removal of stumps and other deleterious matter, dressing of
13.1 sides and bottom and backfilling with approved material etc. and as per
16
relevant clauses of section 300 & 2100 in

I Soil
i) upto 3 m depth Drain Cum 136 122.40 4972.5 ₹ 6,08,634.00
Providing and laying cement concrete grade 1:3:6 with 40mm graded
crushed stone aggregate, (M-10 nominal mix) including the cost of
17 6.10.4 centering and shuttering. Compacting with appropriate method, Cum 2886 2597.40 382.5 ₹ 9,93,506.00
finishing and curing and as per relevant clauses of section.603.

Providing and laying Plain/Reinforced cement concrete (mixed in

concrete mixture) in open foundation including form work shuttering
13.6 etc. complete as per drawing and technical specifications and as per
18
relevant clauses of sections 1500, 1700 & 2100 with .
e) RCC Grade M20 with 20 mm maximum size of aggregate Cum 4277 3849.30 1782.45 ₹ 68,61,185.00
Supplying, fitting and placing un-coated HYSD bar reinforcement in
13.26 foundation complete as per drawing and technical specifications and as
19
per relevant clauses of sections 1600.
Steel in drain @65kg/cum tonne 56994 51294.60 115.85925 ₹ 59,42,954.00
Providing & fixing in position precise Reinforced Cement Concrete
manhole
8.26 covers with and without frames confirming to IS-12592(Part I&II) 1991
20

560 mm x 900 mm extra heavy duty rectangular cover with frame

8.26.1.9 Each 3102 2791.80 65.7 ₹ 1,83,421.00
@ 10 mtr C/c
Providing weep holes in Brick masonry/Plain/Reinforced concrete
abutment, wing wall/return wall with 100 mm dia AC pipe, extending
through the full width of the structure with slope of 1V :20H towards
21 14.8 drawing foce. Complete as per drawing and Technical specifications and Meter 131 117.90 ₹ 0.00
as per clause 2706 of specifications.

Total Amount.:- ₹ 2,87,46,318.00

45 of 51
 PROJECT - UJJAIN SMART CITY SPORTS COMPLEX

SUB. : BOQ FOR SWIMMING POOL FILTRATION SYSTEM EQUIPMENT & ACCESSORIES
DIVING POOL + LEISURE POOL + WARMUP POOL
S.No. Swimming Pool L (Mtr) W (Mtr) D(Mtr) Holdup
1 Diving Pool Dimensions: 25m.(Length) , 20m. (Width) x 4 m - 5 m Depth. 25 20 4.5 2250
2 Leisure Pool Dimensions: 25m.(Length) , 20m. (Width) x 4 m - 5 m Depth. 30 10 1.1 330
3 Warm Up Pool Dimensions: 25m.(Length) , 13 m. (Width) x 1.1 -1.4 m Depth. 25 13 1.1 357.5
4 TOTAL 2937.5
Volume: 2940 Cu m Total Volume = 2940 Cu M + 160 Cu M ( B/Tank ) = 3100 Cu M
Filtration turn over: - 6hrs- 8 Hr max
Filtration flow rate: 338 m3/hr
Filtration velocity: 35m3/hr/m2
Pool type : Overflow
Balance tank capacity: 160 Cu m

Description Unit Rate Total

Sr. No. Qty Unit
In INR In INR
1 SITC of Filters Vessels 4 nos. 7,25,000.00 29,00,000.00
Totally anticorrossive bobbin wound sand filter 2.0 M dia fitted with collector
manufactured with fibre glass and polyester resin, arms and diffuser made from
unplasticised PVC and Polypropelene. Filter media height -1000mm and capable of
accomodating a flow rate of 105 m³/hr @ 35m³/hr/m²Complete with lid in
polyester resin and fibre glass,manual air purge cap for sand discharge and
140PVC flanged connection for inlet and outlet.
Make: Astral, Spain Code: 00706 / Hurlcon / Hyward

2 SITC of 5 VALVE BATTERY 4 nos. 2,42,100.00 9,68,400.00

140mm Valve battery built in PVC with flange connections to filters according to
DIN standards. 140mm Butterfly valves also in PVC. Supports made of zinc-coated
steel with antivibration clamps and fixing screws
Make: Astral, Spain Code: 00789 BS 20 / Hurlcon / Hyward

3.1 Supply & Commissioning of Filter Media Sand 0.42 - 0.8 mm 18000 kg 15.00 2,70,000.00
3.2 Supply & Commissioning of Gravels 1 - 2 mm 4000 kg 15.00 60,000.00
Make : Indigenous

4 SITC of 5 VALVE BATTERY SUPPORT 4 nos. 18,500.00 74,000.00

Zinc-coated steel supports - 2nos.with antivibration clamps and fixing screws for the
above
Make: Astral, Spain Code: 28697 / Hurlcon / Hyward

5 SITC of CIRCULATING PUMPS ( 3 No. Working + 1 No. SB ) 5 nos. 2,75,000.00 13,75,000.00

Horizontal monobloc circulating pumps with body, prefilter, and support in Cast
iron, shaft in AISI-420 stainless steel mechanical seal and prefilter basket in AISI-
316 stainless steel.and impeller in cast iron with motor -3000rpm, 3ph,400/690V,
12.5 HP, 50Hz and class-F insulation, Flow: 107 m³/hr @ 17m head,
Duty - 4nos and Stand by - 1no.
Make: Astral, Spain Code: 01204 / Hurlcon / Hyward

SITC of CENTRALISED PUMP ELECTRIC CONTROL PANEL

Integrated, cubical type, 16 SWG powder coated CRCA sheet control panel to
mounted to the foundation. The control panel should be suitable for 440 volts, 50
Hz, 4 wire supply. Quoted price shall include with 25mm thick rubber mats, wiring,
cabling, control wiring and copper grounding from control panel to various
6 equipment like recirculation pump, dosing equipment, agitator etc. The panel shall 1 nos. 2,25,000.00 2,25,000.00
have compartment for bus bar and cable alleys. The panel should be in accordance
with the specifications. Providing and fixing necessary cables, internal wiring for all
equipments and power cabling for motors, dosing systems, controller etc. Control
panel should consist of Ammeter, Volt meter, Selector Switch, Single phase
preventer etc. Cost should be included in the cost of M.C.C. etc. complete.
Make - Indiginous

7 AUTOMATIC pH / REDOX CONTROLLER 4 nos. 79,092.00 3,16,368.00

Page 46 of 51
 Description Unit Rate Total
Sr. No. Qty Unit
The Optima series, featuring all-new power supply technology available from 90
V ac up to 265 V ac and 50-60Hz, guarantees unprecedented dosing precision and adaptability.

Optima dosing pump with built-in pH/Redox control. pH/Redox instrument.

Automatic calibration: Calibration by simply pressing a key, with the possiblity of controlling the level
of sensor efficiency
Available functions:
- 90-265 VAC 50/60 Hz power supply
- Manual compensation of temperature for pH or automatic compensation by
means of PT100.
- 4…20mA output for graphic recorder or transmitting the measured value.
- Level alarm with pump disconnection or simple warning of lack of product by
means of the alarm relay.
- Set point deviation alarm, programmable for the entire measurement interval
- O.F.A. time (Over Feed Alarm) to prevent the dosing pump from infecting
product if the sensor malfunctions.
- Maximum dosing pump flow rate for preventing overdosing.
Password for protecting programmed data.
- Available alarms.
Make: Astral, Spain Code: 57140/Eq

8 pH Electrode 4 nos. 10,980.00 43,920.00

Make: Astral, Spain Code: 01303/Eq

9 Rx Electrode 4 nos. 10,980.00 43,920.00

Make: Astral, Spain Code: 01304/Eq

10 Electrode Holder 4 nos. 10,980.00 43,920.00

Make: Astral, Spain Code: 01305/Eq

11.1 DOSING PUMP for Chlorine & pH correction 02 nos. 36,500.00 73,000.00

Constant flow membrane dosing pump, electronic low voltage circuit with 220V-48V
transformer, aluminium housing with epoxy anti-acid varnish protection and
anodized aluminium dial, transparent polycarbonate lid, IP-54 protection Flow:
10l/hr @ 5kg/cm² (2nos. Each for chlorine & Acid/ Soda Ash )
Make: Astral, Spain Code: 33841

11.2 SOLUTION PREPARATION TANK 02 nos. 23,500.00 47,000.00

Semi transparent polyurethalene tank with external scale marked with levels ,
capacity of tank 250lts.( 1 no. each for chlorine and Acid/ Soda Ash)
Make: Astral, Spain Code: 01316 / Hurlcon / Hyward

11.3 STIRRING ROD 02 nos. 7,600.00 15,200.00

Agitators for easy installation in the tanks, provided with steering grip in bakelite,
rod and propellor arms in PVC, length of stirring rod 600mm. ( 1no. each for
chlorine and Acid/ Soda Ash)
Make: Astral, Spain Code: 01318 / Hurlcon / Hyward

12 COMMISSIONING CHEMICALS
12.1 Combo Pack ( Including 10 Kg TCCA 90 + 10 Kg Algines ) 6 nos. 4,750.00 28,500.00
12.2 Non Ferric Alum 500 Kg 20.00 10,000.00
12.3 25 Kg Bleaching Bag 50 Bag 500.00 25,000.00
Make: Indiginous

13 SUCTIOON SWEEPER ASSEMBLY

Supply & trial run of VACCUM HEAD
1 Polished anodized aluminium and crome bronze 2" pipe connection X length 800 1 nos. 48,750.00 48,750.00
mm trailed via Al pole / Rope
Make: Astral, Spain Code : / Hurlcon / Hyward

Page 47 of 51
 Description Unit Rate Total
Sr. No. Qty Unit

Supply & trial run of VACCUM HEAD

2 Polished anodized aluminium and crome bronze 1 1/2" pipe connection length 350 1 nos. 13,500.00 13,500.00
mm trailed via Al pole
Make: Astral, Spain Code : 1353 / Hurlcon / Hyward

Supply and trial test of TELESCOPIC HANDLE in anodized aluminium which can
be adapted to the entire range of cleaning equipment, brushes, deep net with
butterfly connection

3 2.4 - 4.8 m Long 1 nos. 5,750.00 5,750.00

Make: Astral, Spain Code: / Hurlcon / Hyward

4 4-7.8 m Long 1 nos. 18,750.00 18,750.00

Make: Astral, Spain Code: / Hurlcon / Hyward

Supply and Trial Test of FLOATING HOSE

5 Plastic vacuum hose 2" dia, 30 mtrs long with cuffs well adaptable to the Vacuum 1 nos. 16,250.00 16,250.00
Head via hose clamp in Galvanised Steel
Make: Astral, Spain Code: / Hurlcon / Hyward

Supply and Trial Test of DEEP BAG NET

Deep bag net made in polypropylene and white polyester netting with wing-nut
6 2 nos. 2,750.00 5,500.00
connection and to be able to be connected to the telescopic handle supplied as per
specifications. The deep net should be at leat 300 mm wide
Make: Astral, Spain Code: / Hurlcon / Hyward

Supply and Trial Test of CURVED BRUSH

Curved brush made in polypropylene for pool basins and scum liners with wing - nut
7 2 nos. 1,950.00 3,900.00
connection.and to be able to connected to the telescopic handle supplied as per
specification.The length of curved brush bristles should be atleast 300 mm long

Make: Astral, Spain Code: / Hurlcon / Hyward

Assembling and Trial Testing of TROLLEY MOUNTED PUMP: Powder Coated in

siemens grey trolley made in fabricated mild steel mounted on nylon wheels of min.
150 mm Dia. & Min. 2 Nos. with bottom support . The trolley should be able to bear
8 1 nos. 55,000.00 55,000.00
the load of 2 HP self priming pump of suction delivery size 50 NB X 50 NB , 1 Sq.
mm insulated unarmoured cable min. 30 m 2 HP DOL starter should be provided
with pump
Make - Indiginous

14 POOL BASIN ITEMS

SITC of MAIN DRAIN

SS 304 Square main drain 450mm x 450mm with main frame screwed on base
frame also in SS 304 duly groutable on the pool bottom deepest part. The drain
a 2 nos. 32,500.00 65,000.00
plate should be able to collect a water volume of not less than 35 M3/hr @ a drain
velocity of 1.0 m/sec. The hole size on drain plate not to exceed 10 mm and qty of
holes to match the said flow
Make: Astral, Spain Code: / Hurlcon / Hyward

SITC of MAIN DRAIN

SS 304 Square main drain 500mm x 500mm with main frame screwed on base
frame also in SS 304 duly groutable on the pool bottom deepest part . The drain
10.2 2 nos. 62,500.00 1,25,000.00
plate should be able to collect a water volume of not less than 75 M3/hr @ a drain
velocity of 1.0 m/sec. The hole size on drain plate not to exceed 10 mm and qty of
holes to match the said flow
Make: Astral, Spain Code: / Hurlcon / Hyward

SITC of FILTERED WATER FLOOR INLET

b 50 nos. 1,450.00 72,500.00
Concrete floor inlet with ss screw flow 12 m3/hr with 2" female and male connection

Make: Astral, Spain Code: / Hurlcon / Hyward

15 SITC of UNDERWATER ILLUMINATION 56 nos. 8,341.00 4,67,096.00

Standard Underwater light 300W x 12 V in white ABS rim, niche inpolypropylene
with 2.5 meter cable,
Make: Astral, Spain Code: 07844 / Hurlcon / Hyward

Page 48 of 51
 Description Unit Rate Total
Sr. No. Qty Unit
16 SITC of Deck Box in ABS with 3 entries of 3/4" 56 nos. 1,617.00 90,552.00
Make: Astral, Spain Code: 30825 / Hurlcon / Hyward

SITC of Flexible conduit hose 1 m long for connecting light to the box. 3/4" and 95 nos. 650.00 61,750.00
17 M25 threaded ends,for lights ( with cable )
Make: Astral, Spain Code: 28138 / Hurlcon / Hyward

SITC of Low voltge swimming pool transformer with protective shield between 56 nos. 7,758.00 4,34,448.00
18 primary & secondary windings, internal protection against overload,300 VA, 230 V
primary and and12 V secondary voltage with tappings for different cable lengths
Make: Astral, Spain Code: 00384-1381 / Hurlcon / Hyward

19 SITC of UNDER WATER LIGHT TRNASFORER PANEL 5 nos. 62,500.00 3,12,500.00

Integrated, cubical type, 16 SWG powder coated CRCA sheet control panel to
mounted to the foundation. The control panel should be suitable for 440 volts, 50
Hz, 4 wire supply. Quoted price shall include with 25mm thick rubber mats, wiring,
cabling, control wiring and copper grounding from control panel to various
Transformers .
The panel shall have compartment for bus bar and cable alleys. The panel should
be in accordance with the specifications. Providing and fixing necessary cables,
internal wiring for all equipments etc. Control panel should consist of Ammeter,
Volt meter, Selector Switch, Single phase preventer etc. Cost should be included in
the cost of M.C.C. etc. complete.

POOL SIDE EQUIPMENT

20 LADDER- 3 steps 4 nos. 26,500.00 1,06,000.00
SITC of Loop model stainless steel AISI-304 ladders with added top double safety
step width: 500mm, handrails dia 43mm stainless steel non-slip steps, provided
with earth connection and anchoring fixtures. No. of steps - 3
Make: Astral, Spain Code: / Hurlcon / Hyward

21 LADDER- 5 steps 4 nos. 32,500.00 1,30,000.00

SITC of Loop model stainless steel AISI-304 ladders with added top double safety
step width: 500mm, handrails dia 43mm stainless steel non-slip steps, provided
with earth connection and anchoring fixtures. No. of steps - 5
Make: Astral, Spain Code: / Hurlcon / Hyward

22 LADDER- 15 steps 2 nos. 45,000.00 90,000.00

SITC of Overflow model stainless steel AISI-304 ladders with added top double
safety step width: 500mm, handrails dia 43mm stainless steel non-slip steps,
provided with earth connection and anchoring fixtures. No. of steps - 15
Make: Indiginous

23 LADDER- 20 steps 2 nos. 55,000.00 1,10,000.00

SITC of Overflow model stainless steel AISI-316 ladders with added top double
safety step width: 500mm, handrails dia 43mm stainless steel non-slip steps,
provided with earth connection and anchoring fixtures. No. of steps - 20
Make: Indiginous

24 OVERFLOW GUTTER GRATINGS 5400 nos. 76.00 4,10,400.00

SITC of Modular transversal grating for curves, stablised against UV rays.
Ht.35mm, width: 335mm
Make: Astral, Spain Code: 34197 / Hurlcon / Hyward

25 GRATING SUPPORT PROFILE 250 R. Mtr 922.00 2,30,500.00

SITC of Made of unaltertable plastic, adaptable to 22, 24, 35 mm

Page 49 of 51
 Description Unit Rate Total
Sr. No. Qty Unit
grating height
Make: Astral, Spain Code: 00224 / Hurlcon / Hyward

SAFTY EQUIPMENT
Supply and trial test of (i) Life Buoys ring for pool safety. The same mounted near
26
the Swimming Pool as per the Safety Requirements 2 nos. 16,500.00 33,000.00
Make: Astral, Spain Code: / Hurlcon / Hyward

Supply and trial test of (ii) Lifeguard Loop and placed near the pool area as per the
27
safety requirements 2 nos. 12,350.00 24,700.00
Make: Astral, Spain Code: / Hurlcon / Hyward

28 Supply of (iii) Artificial Respirator ( Ambu Bag ) 2 nos.

Make:

29 SITC for Plumbing Connection Header 4 nos. 85,000.00 3,40,000.00

Providing and fixing of plumbing pipie header in SS 316 as per approved design
having flanged end connection for various pipe connection between pump , doser &
filters
Make - Indiginous

30 SITC for Plumbing / Electrical Connectors

Providing and fixing of plumbing piping / Electrical connectors at RCC insurtion in
10 PN RPVC pipe with non leakage intigrated flange system for Varoius sizes 1.5" - 20 nos. 1,750.00 35,000.00
6"
Make - Supreme / Astral / Finolex

Float Line anchors made in S.S.-316 30 No 6,790.00 2,03,700.00

Make : Astral Spain code 00140 / Eq.
Level anchor fixing in S.S.-316 5 No 13,170.00 65,850.00
Make : Astral Spain 00141 / Eq.
Level anchor fixing in S.S.-316 10 No 13,170.00 1,31,700.00
Make : Astral Spain code 00141 / Eq.

31 SITC for Plumbing / Electrical work related with filter system & U/W Lights

Providing and fixing of plumbing piping and electrical (Excluding excavation and
back filling + Base PCC ) Supply Installation & Testing of PVC pressure pipes
manufactured as per IS 4985:2000 standard including all heavy duty fittings. All
pipes for overflow and inside concrete basin and filter room in PN 10.
Make - Supreme / Astral / Finolex

PVC 315 MM OD 6 PN (12") 50 Rmt 1,643.00 82,150.00

PVC 160 MM OD 10 PN (6") 300 Rmt 630.00 1,89,000.00
SOR
PVC 160 MM OD 6 PN (6") 225 Rmt 493.00 1,10,925.00
No 5.1
PVC 110 MM OD 10 PN (3") 250 Rmt 292.00 73,000.00
PVC 90 MM OD 10 PN (3") 115 Rmt 195.00 22,425.00
PVC 75MM OD 10 PN (3") 105 Rmt 178.00 18,690.00
PVC 63 MM OD 10 PN (2") 150 Rmt 107.00 16,050.00
PVC 32 MM OD 10 PN (1") 325 Rmt 86.00 27,950.00
-
SITC OF f NRV AS REQUIRED FOR PUMPS WITH FLANGES AND NUT BOLTS
32 MOC : Cast Iron body & seat in EPDM / Nitrile as per site requirement & GFC
drawing
Make - Intervalve / Zoloto / Flowcon
63 MM size ( 2" ) 6 No. 5,580.00 33,480.00
80 MM size ( 3" ) 2 No. 7,541.00 15,082.00
110 MM size (4" ) 4 No. 9,970.00 39,880.00
150 MM size ( 6" ) 4 No. 21,330.00 85,320.00

SITC of BUTTERFLY VALVES FOR PUMPS WITH FLANGES AND NUT BOLTS
33 MOC : Cast Iron body & seat in EPDM / Nitrile as per site requirement & GFC
drawing
Make - Intervalve / Zoloto / Flowcon

63 MM size ( 2" ) 4 No. 2,239.00 8,956.00

(SOR 80 MM size ( 3" ) 3 No. 2,427.00 7,281.00
No 6.6) Page 50 of 51
 Description Unit Rate Total
Sr. No. Qty Unit
No 6.6) 110 MM size (4" ) 3 No. 3,073.00 9,219.00
150 MM size ( 6" ) 1 No. 4,647.00 4,647.00

SITC of BALL VALVES as per site requirement & GFC drawing

34
MOC : UPVC / RPVC
Make - Supreme / Astral

32 MM size ( 1" ) 8 No. 936.00 7,488

40 MM size ( 1.5" ) 6 No. 14,444.00 86,664
63 MM size ( 2.5" ) 6 No. 3,253.00 19,518

ELECTRICAL CABLES
Supplying, laying and commissioning of PVC insulated and sheathed power cable
35
conforming to IS:1554 part-I 1988 as per specifications laid and in 3/4" BSP pvc
conduits
Make - Finolex / Havells

2 core unarmored copper cable 6.0 mm2 for UW lights 2500 Rmt 170.00 4,25,000

4 core unarmored copper cable 4.0 mm2 for Pumps 2500 Rmt 300.00 7,50,000

36 DIVING BOARD
Supplying & fixing on position of Maxiflex B Model 16ft Diving Board with short
stand without hand guard rail and complete with fulcrum unit. including Diving
board brackets in SS304 & all material, labour and transportation, chases and holes
4 Nos 1,00,000.00 4,00,000
in concrete/ wall/ floor wherever required and repair the same with waterproofing
compound etc. complete as per instruction of architect consultant / engineer in
charge.
Make: Duraflex

1,26,59,049.00

Page 51 of 51