Quick Start Guide
Quick Start Guide
2.Working Environment
Do not focus the camera lens on strong light such as the sun or incandescent lamp; otherwise the strong light
will cause overexposure or light leak (not camera malfunction), which may shorten camera lifetime.
Please transport, use and store the device within defined humidity and temperature ranges.
Do not expose it in damp, dusty, extremely hot or cold places or places with intense electromagnetic radiation
or with unstable lighting.
Keep the camera away from water or any liquid to avoid damage to internal components.
To avoid heat accumulation, please do not block the ventilation around the device.
While shipping the camera, pack it in the factory packing or use materials with equivalent quality.
When shipping, storing and installing the device, try to prevent it from damages caused by pressure, violent
vibration and soaking.
This product is not water-proof and cannot be used outdoor alone.
Working Environment
1
3. Daily Maintenance
Do not touch the heat component of the device directly to avoid empyrosis.
When the lens is contaminated by dust or grease, use cotton cloth or lens clean cloth to wipe it off. When it is
hard to clean, dip some lens cleanser and wipe gently and rotate outward from the middle until it is clean.
Never apply any organic solvent with ethanol or benzene to clean the lens and housing.
Do not disassemble or repair the device in any way by yourself. We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.
If the product does not work properly, please contact your dealer or the nearest service center.
4. Special Statement
The product appearance is subject to the actual device and picture in this Guide is for reference only..
Every effort has been made to ensure the accuracy and validity of this Guide. Any update of this Guide caused
by version upgrade is subject to change without notice.
This Guide is made for multiple models but it will not illustrate one by one. Please refer to it according to the
actual products you are using.
This device can be used after being activated through IPCSearch in the attached CD. During activation please
fill a valid email address for finding back the password.
To ensure the safety of device on internet, it is strongly recommended that you set a strong password which is
composed of at least 2 kinds of the following, digits, case-sensitive letters or specific symbols, and whose
length ranges from 8 to 16 bits. Please modify the password periodically and once every 3 months is
recommended. If the device is used in highly risky environment, suggest modifying the password monthly or
weekly. Please keep your user name and password safe.
Accessing this device to the internet is at user's own risk, including but not limited to the possible network
attack, hacker attack, virus infection and etc. This company will not assume any responsibility for problems of
product abnormality and information disclosure caused thereof. We shall provide technical support relating to
the products in time.
[Notice]: For more information, please refer to the User Manual for HD IP Camera in the attached CD.
2
III. Appearance and Interface
Dimensions:
Unit: mm
62
161.5
161.5
7 3-∅4 .5
∅5
Components:
1
3
3
Buttcock line:
1
2
Diameter
Distance 0.80 1.00 1.25 1.63 2.00
(mm)
(m)
(AWG20) (AWG18) (AWG16) (AWG14) (AWG12)
Power (W)
6 29 45 70 119 179
10 17 27 42 71 107
20 6 13 21 36 54
30 9 9 14 24 36
40 4 7 11 18 27
50 - 5 8 14 21
60 - - 7 12 18
70 - - 6 10 15
80 - - - 9 13
90 - - - 8 12
100 - - - - 11
110 - - - - 10
120 - - - - 9
4
V. Installation
The camera supports wall bracket mount and pendent mount.
You can perform ceiling or wall mount when the wall or ceiling are thick and solid enough for fixing self-tapping
screws and meanwhile strong enough for bearing the device.
When installing the device outdoor, a waterproof joint box is necessary to get good waterproofness. As the
waterproof joint box is optional, please contact your supplier or customer service personnel to purchase.
The waterproof joint box and its installation sketch are shown below. Please refer to the Quick Start Guide of
the waterproof joint box for detailed installation.
5
Wall Bracket Mount:
The installation steps of wall bracket mount and pendent mount are the same. This part will take wall bracket
mount as an example to introduce the installation steps.
1. Install TF card (optional). Some models support TF card. Insert a TF card into the slot as shown in the following
picture. The max supported memory of TF card is 128G. After insertion, hot-swapping the TF card is not
recommended.
2. Drill holes on the mounting surface. Pick out the installation sticker from the attachment and stick it to the
mounting surface . Drill holes according to the hole marks on the sticker and insert the 3 expansion screw bolts
thoroughly into the holes.
If routing cables from the top of the mounting surface, a cable outlet hole is also needed on the wall. If routing
cables from the profile side of the device, lead the cables out through the U-shaped groove at the side of the
base.
②Align and drill holes
70mm
③Insert expansion
screw bolts
∅=6mm
68mm
35mm
70mm
Cable Hole
∅=6mm ∅=6mm
6
3. Route cables. When routing cables from the top, route cables through the mounting surface. When routing
cables from the profile side, route cables through the U-shaped groove at the side of the bracket base.
Side wiring
Top wiring
7
4. Fix device base onto the wall. Align the 3 screw holes on the device base to those 3 expansion screw bolts on
the mounting surface. Screw up the 3 tapping screws through the base and tighten them into the 3 expansion
screw bolts. Lock them up and fix the device onto the mounting surface.
5. Adjust lens surveillance direction. Loosen the locknut on the base, rotate the camera manually in horizontal
and vertical directions. After adjusting directions, tighten the locknut on the base and peel off the protective
film on the lens.
Locknut
90°
8
VI.Login to Client
1. Minimum configurations and system requirements:
Ÿ Processor: 3.3 GHz CORE®i3 series or other equivalent processors
Ÿ RAM Memory: 4GB or above
Ÿ Operating System: Windows XP or newer version
Ÿ Browser: IE7.0 and newer version, Firefox, Google Chrome (41 and lower)
Ÿ DirectX:9.0c
2. Device Activation
When using the device for the first time, run IPCSearch in the attached CD: it will search devices in LAN
automatically and display the list of device IP address, gateway and etc. If the network provides DHCP service,
DHCP server will assign IP for the camera automatically.
Batch: Select the device and click “Batch processing”. In the popup interface, set admin user's password and
the email address to find back the password. Click “Activate” and wait for rebooting.
Individual: Select the device from IPCSearch and right click to select “Active”. Fill admin user name and
password and the e-mail address to find back the password. Click “Activate” and wait for rebooting.
Web client: the device can also be activated through the web client. Set PC and the device in the same network
segment and login to the web. User can set admin password and password reset email on the interface and
click "Activate".
9
3. Modify device IP address
Click “Modify Params” and set the network parameters. When configuring a static IP for the camera, please
check “Custom device address (Close DHCP)” and fill the Ethernet parameter. During the modification, the
user name (admin) and the password set before activation should be entered. After configuration, the camera
will reboot automatically and this takes 60s.
1) Double click the device in IPCSearch or click “Login”. Enter user name and password to login the web client.
10
2) After login, download and install the plug-in. Close browser during installation.
3) Re-login to the web client and view live video directly.
[Notice]: Interface of different models may differ. Please subject it to the actual product. Please refer to the
Help file for detailed explanation.
Adjust camera direction, configure camera parameters in web client until the live view meets requirement.
11
05.03.800571 V1 20170823