Scribd
Upload
72 views

UPS Installation Procedure 2

This document provides information about installing and using an uninterruptible power supply (UPS) device. It includes instructions on checking the package contents upon opening, selecting an appropriate installation environment, connecting the UPS for initial use, switching the UPS on from the mains power or battery, switching the UPS off, and descriptions of status messages displayed on the UPS control panel. The document is an installation and operation manual for a specific UPS model.

Uploaded by

vimal alaberah
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
72 views

UPS Installation Procedure 2

This document provides information about installing and using an uninterruptible power supply (UPS) device. It includes instructions on checking the package contents upon opening, selecting an appropriate installation environment, connecting the UPS for initial use, switching the UPS on from the mains power or battery, switching the UPS off, and descriptions of status messages displayed on the UPS control panel. The document is an installation and operation manual for a specific UPS model.

Uploaded by

vimal alaberah
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

REAR VIEW

66

800VA / 1100VA Model 1500VA / 2000VA Model

Communication port RS232 Cooling fans

USB communication port IEC 10A output socket

Circuit breaker Energyshare

Communication Card Slots IEC 10A input plug


DISPLAY PANEL VIEW

“SEL” button (Select) Load level indicator

“ON” button Configuration area

“STAND-BY” button Maintenance request

Regular operation Timer

Mains operation Measurement display area

Battery operation Stand-by / alarm

AVR active EnergyShare

Battery charge indicator


INSTALLATION

INITIAL CONTENT CHECK


After opening the packaging, it is first necessary to check the contents.
The package must contain:

88 UPS Schuko power cable - IEC 10A

2 IEC 10A connection cables USB cable

RS232 cable User manual CD + Safety manual

INSTALLATION ENVIRONMENT
The UPS and the Battery Box must be installed in ventilated, clean environments which are sheltered from bad weather.
The relative humidity in the environment must not exceed the maximum values shown in the Technical Data table.
The ambient temperature, whilst the UPS is in operation, must remain between 0 and 40°C, and the UPS must not be
positioned in places which are exposed to direct sunlight or to hot air.

The recommended operating temperature for the UPS and the batteries is between 20 and 25°C. The actual
operating life of the batteries is 5 years on average with an operating temperature of 20°C. If the operating
temperature reaches 30°C, the operating life is halved.

This is a category C2 UPS product. In a residential environment, this product may cause radio interference,
in which case the user may be required to take additional measures.
USE

CONNECTIONS AND SWITCHING ON FOR THE FIRST TIME


1) Confirm that the installation upstream of the UPS is adequately protected against overloads and short circuits. It is
recommended that the rating of this protection is either 10A or 16A type B or C (depending on the UPS power rating), always
check prior to connection.
2) Power the UPS using the input cable provided. 9
3) Press the ON/OFF switch located on the front panel.

4) After a few moments, the UPS will switch on, the display will light up, there will be a beep and the icon will start to flash.
The UPS is in stand-by mode: meaning that it is only consuming a small amount of power. The microcontroller supervising
the self-diagnoses is powered; the batteries are charging; and everything is ready for UPS activation. Battery operation is also
in stand-by mode provided that the timer is active.
5) Ensure that the cables connecting any devices to the output sockets of the UPS do not exceed a maximum of 10m in length.
6) Check which operating mode is set on the display and, if necessary, see the “Configuring operating modes” paragraph to set
the required mode. For advanced UPS configurations execute the software UPSTools which can be downloaded from the web
site www.ups-technet.com.

SWITCHING ON FROM THE MAINS


1) Press the “ON” button for 1 second. After pressing it, all the icons on the display light up for 1 second and the UPS beeps.
2) Switch on the equipment connected to the UPS.
When switching on for the first time only: after 30 seconds, check that the UPS is operating correctly:
1) Simulate a blackout by disconnecting power to the UPS.

2) The load must continue to be powered, the icon on the display must light up and there must be a beep every 4
seconds.
3) When power is reconnected, the UPS must go back to operating from the mains.

SWITCHING ON FROM THE BATTERY


1) Press the ON/OFF switch located on the front panel.
2) Hold down the “ON” button for at least 5 seconds. All the icons on the display light up for 1 second.
3) Switch on the equipment connected to the UPS.

SWITCHING OFF THE UPS


In order to switch off the UPS, hold down the “STBY” button for at least 2 seconds. The UPS goes back to stand-by mode
and the icon starts to flash:
1) If the mains power is present, the ON/OFF switch must be pressed to completely turn off the UPS.
2) During battery mode operation with the timer not set, the UPS automatically switches off after 30 seconds. However if, the
timer is set, press and hold down the "STBY" key for at least 5 seconds to turn off the UPS. For complete shutdown, press the
ON/OFF switch.
DISPLAY PANEL MESSAGES
This chapter describes, in detail, the various information that can be displayed on the LCD.

UPS STATUS MESSAGES


ICON STATUS DESCRIPTION

10
10 Fixed Indicates a fault

Flashing The UPS is in stand-by mode

Fixed Indicates regular operation

Fixed The UPS is operating from the mains

The UPS is operating from the battery. In this condition, the UPS emits an
Fixed
acoustic signal (beep) at regular 4-second intervals.

Low battery pre-alarm. Indicates that battery autonomy is coming to an


Flashing
end. In this condition, the UPS emits a beep at regular 1-second intervals.

Fixed AVR active

Dynamic Indicates the estimated percentage charge of the batteries

Indicates the percentage of charge applied to the UPS compared with the
Dynamic
nominal value.

Flashing Maintenance is required. Contact the support centre.

Indicates that the timer is active (programmed switch-on and switch-off).


Fixed
The timer can be activated/deactivated using the software provided.

Flashing 1 minute until the UPS switches back on or 3 minutes until it switches off

Off * The EnergyShare sockets are not configured. (Always active).


Using UPStools software an event associated with the EnergyShare
Continuous* sockets was configured (e.g. end of discharge pre-alarm threshold) but
the sockets are active at this time.
The associated event occurred; the EnergyShare outlets have been
Flashing *
disconnected.

* For more information about the configuration of the EnergyShare sockets, see "Additional Features"

You might also like