Contents

1.COMMAND LIST....................................................................................... 3

2.COMMANDS DESCRIPT ............................................................................. 4

1.HT .................................................................................................... 4
2.LF ..................................................................................................... 4
3.CR .................................................................................................... 5
4.ESC SP N ......................................................................................... 5
5.ESC ! N ............................................................................................ 5
6.ESC $ NL NH .................................................................................... 6
7.ESC B N ........................................................................................... 6
8.ESC % N .......................................................................................... 7
9.ESC & Y C1 C2 [X1 D1...D(Y X X1)]...[XK D1...D(Y X XK)] ............................. 7
10.ESC *  M NL NH D1...DK .................................................................. 9
11.ESC - N ........................................................................................ 11
12.ESC 2 ........................................................................................... 12
13.ESC 3 N ........................................................................................ 12
14.ESC ? N ........................................................................................ 12
15.ESC @ .......................................................................................... 13
16.ESC D N1...NK NUL ........................................................................ 13
17.ESC E N........................................................................................ 14
18.ESC G N ....................................................................................... 14
19.ESC J N ........................................................................................ 14
20.ESC R N ....................................................................................... 15
21.ESC V N........................................................................................ 15
22.ESC V N ........................................................................................ 16
23.ESC A N ........................................................................................ 17
24.ESC SO N ..................................................................................... 17
25.ESC DC4 N .................................................................................... 17
26.ESC D N ........................................................................................ 18
27.ESC T N ........................................................................................ 18
28.ESC { N ........................................................................................ 19
29.FS P N M ...................................................................................... 20
30.FS Q N [XL XH YL YH D1...DK]1...[XL XH YL YH D1...DK]N ............................ 20
31.GS ! N .......................................................................................... 23
32.GS *  X Y D1...D(X X Y X 8) ......................................................... 24
33.GS / M ......................................................................................... 26
34.GS B N ......................................................................................... 26
35.GS H N ......................................................................................... 27
36.GS L NL NH .................................................................................... 27
37.GS A N ......................................................................................... 28
38.GS H N ......................................................................................... 28
39.GS K M D1...DK NUL/GS K M N D1...DN............................................. 28
1
40.GS X N.......................................................................................... 32
41.GS R N ......................................................................................... 32
42.GS V 0 M XL XH YL YH D1....DK ......................................................... 33
43.GS W N ......................................................................................... 34
44.FS ! N .......................................................................................... 35
45.FS & ............................................................................................. 36
46.FS . .............................................................................................. 36
47.ESC = N ........................................................................................ 36
48.ESC 7 N1 N2 N3 ............................................................................ 37
49.ESC 8 N1 N2 ................................................................................. 37
50.ESC 9 N ........................................................................................ 37
51.DC2 T ........................................................................................... 38
52.ESC P M T1 T2(FOR DRAWER) ............................................................. 38
53.ESC U N (FOR DRAWER) ...................................................................... 38
54.ESC C 5 N(FOR BUTTONS) ................................................................... 39

2
1.Command List
Type Command Name
LF Print and line feed
CR Print and carriage return
HT JMP to the next TAB position
Print
ESC D n Set horizontal tab positions
Command
ESC J n Print and Feed n dots paper
ESC d n Print and Feed n lines
ESC = n Toggle the printer online or offline
ESC 2 Select default line spacing
ESC 3 n Set line spacing
ESC a n Select justification
Line spacing ESC SO Select Double Width mode
Command ESC DC4 Disable Double Width mode
GS L nL nH Set the left blank margin with dots
ESC $ nL nH Set absolute print position
ESC B n Set Left Space
ESC ! n Select print mode(s)
GS ! n Set or Cancle the double width and height
GS B Turn white/black reverse printing mode
ESC V n Turn 90°clockwise rotation mode on/off
ESC v n Transmit paper sensor status
ESC G n Turn on/off double-strike mode
ESC E n Set or Cancle bold font
ESC SP n Set the space between chars
Character ESC { n Turn upside-down printing mode on/off
Command ESC - n Set the underline dots(0,1,2)
ESC % n Select/Cancel user-defined characters
FS & Select Chinese mode
FS . Select character mode
FS! Set print mode for Kanji characters
ESC & Define user-defined characters
ESC ? n Cancle user-defined characters
ESC R n Select and internation character set
ESC t n Select character code table
ESC * Select bit-image mode
GS * Define downloaded bit image
Bit Image GS / Print downloaded bit image
Command GS v Print the bitmap with width and height
FS p n m Print NV bitmap
FS q n Define NV bitmap
3
Init Command ESC @ Initialize printer
Status GS r n Transmit status
Command GS a n Enable/Disable ASB
GS H Select printing position of human readable characters
GS h Set bar code height
Bar Code
GS w Set bar code width
Command
GS k Print bar code
GS x Set barcode printing left space
ESC 7 n1 n2 n3 Setting Control Parameter Command
ESC 8 n1 n2 Sleep parameter
miscellaneous ESC 9 n Select Chinese code format
function DC2 T Printing test page
commands ESC p Generate pulse (For drawer)
ESC u Transmit peripheral device status (For drawer)
ESC c 5 Enable/disable panel buttons (For button)

2.Commands Descript

1.HT
[Name] Horizontal tab
[Format] ASCII HT
Hex 09
Decimal 9
[Description] Moves the print position to the next horizontal tab position.
[Notes]
This command is ignored unless the next horizontal tab
position has been set.
 If the next horizontal tab position exceeds the printing area,
the printer sets theprinting position to [printing area width +
1].
 Horizontal tab positions are set with ESC D.
 If this command is received when the printing position is at
[printing area width+ 1], the printer executes print
buffer-full printing of the current line andhorizontal tab
processing from the beginning of the next line.
[Reference] ESC D

2.LF
[Name] Print and line feed
[Format] ASCIILF
Hex 0A
Decimal 10

4
 [Description] Prints the data in the print buffer and feeds one line, based
on the current linespacing.
[Note] This command sets the print position to the beginning of the
line.
[Reference] ESC 2, ESC 3

3.CR
[Name] Print and carriage return
[Format] ASCII CR
Hex 0D
Decimal 13
[Description] When automatic line feed is enabled, this command
functions the same as LF; when automatic line feed is
disabled, this command is ignored.
[Notes] • This command line feed is ignored with a serial interface
model.
• Sets the print starting position to the beginning of the line.
[Reference] LF

4.ESC SP n
[Name] Set right-side character spacing
[Format] ASCII ESC SP n
Hex 1B 20 n
Decimal 27 32 n
[Range] 0 ≤ n ≤ 255
[Description] Sets the character spacing for the right side of the character
to [n×0.125 mm (n×0.0049”)].
[Notes] •The right-side character spacing for double-width mode is
twice thenormal value. When characters are enlarged, the
right-side characterspacing is n times normal value.
•This command does not affect the setting of Kanji
characters
•This command sets values independently in standard
mode.
[Default] n=0

5.ESC !n
[Name] Select print mode(s)
[Format] ASCIIESC ! n
Hex 1B 21 n
Decimal 27 33 n
[Range] 0 ≤ n ≤ 255
[Description] Selects print mode(s) using n as follows:

5
6.ESC $ nLnH
[Name] Set absolute print position
[Format] ASCII ESC $ nL nH
Hex 1B 24 nL nH
Decimal 27 36 nL nH
[Range] 0 ≤ nL ≤ 255
0 ≤ nH ≤ 255
[Description] Sets the distance from the beginning of the line to the
position at whichsubsequent characters are to be printed.
•The distance from the beginning of the line to the print
position is[(nL + nH×256)×0.125 mm].
[Notes] •Settings outside the specified printable area are ignored.
• In standard mode, the horizontal motion unit (x) is used.
[Reference] ESC \, GS $, GS \

Bit Off/On Hex Decimal Function

0 Off 00 0 Character Font A (12×24).
On 01 1 Character Font B (9×17).
1 Off 00 0 Turn white/black reverse printing mode not selected.
On 02 2 Turn white/black reverse printing mode selected.
2 Off 00 0 Turn on/off upside-down printing mode not selected.
On 04 4 Turn on/off upside-down printing mode selected.
3 Off 00 0 Emphasized mode not selected.
On 08 8 Emphasized mode selected.
4 Off 00 0 Double-height mode not selected.
On 10 16 Double-height mode selected.
5 Off 00 0 Double-width mode not selected.
On 20 32 Double-width mode selected.
6 Off 00 0 Turn Deleteline mode on/off not selected.
On 40 64 Turn Deleteline mode on/off selected.
7 - - - Undefined.

7.ESC Bn
[Name] Set leftspace
[Format] ASCII ESCBn
Hex 1B 42n
Decimal 27 66 n
[Range] Default is 0
0 ≤ n ≤ 47

6
8.ESC % n
[Name] Select/cancel user-defined character set
[Format] ASCII ESC% n
Hex1B 25 n
Decimal 27 37 n
[Range] 0 ≤ n ≤ 255
[Description] Selects or cancels the user-defined character set.
• When the LSB of n is 0, the user-defined character set is
canceled.
• When the LSB of n is 1, the user-defined character set is
selected.
[Notes] •When the user-defined character set is canceled, the
built-in character set isautomatically selected.
n is available only for the least significant bit.
[Default] n = 0
[Reference] ESC &, ESC ?

9.ESC &y c1 c2 [x1 d1...d(y xx1)]...[xk d1...d(y xxk)]

[Name] Define user-defined characters
[Format] ASCII ESC & y c1 c2 [x1 d1...d(y x x1)]...[xk d1...d(y x xk)]
Hex 1B 26 y c1 c2 [x1 d1...d(y x x1)]...[xk d1...d(y
x xk)]
Decimal27 38 y c1 c2 [x1 d1...d(y xx1)]...[xk d1...d(y
x xk)]
[Range] y = 3
32 ≤ c1 ≤ c2 ≤ 126
0 ≤ x ≤ 12 (when Font A (12×24) is selected)
0 ≤ d1 ... d(y×xk) ≤ 255
[Description] Defines user-defined characters.
• y specifies the number of bytes in the vertical direction.
•c1 specifies the beginning character code for the definition,
and c2 specifies thefinal code.
• x specifies the number of dots in the horizontal direction.
[Notes] The allowable character code range is from ASCII code
<20>H to <7E>H (95characters).
• It is possible to define multiple characters for consecutive
character codes.If only one character is desired, use c1 =
c2.
d is the dot data for the characters. The dot pattern is in the
horizontal directionfrom the left side. Any remaining dots
on the right side are blank.
•The data to define user-defined characters is (y×x) bytes.
• Set a corresponding bit to 1 to print a dot or 0 not to print
7
 a dot.
• This command can define different user-defined
character patterns for eachfont. To select a font, use ESC !
• User-defined characters and a downloaded bit image
cannot be definedsimultaneously. When this command is
executed, the downloaded bit image iscleared.
•The user-defined character definition is cleared when:
1) ESC @ is executed.
2) GS * is executed.
3) ESC ? is executed.
4) The power is turned off.
[Default] The internal character set
[Reference] ESC %, ESC ?
[Example]
• When Font A (12×24) is selected.

8
 d1= <0F>H d4 = <30>H d7 = <40>H . . . .
d2 = <03>H d5 = <80>H d8 = <40>H . . . .
d3 = <00>H d6 = <00>H d9 = <20>H . . . .

10.ESC*m nL nH d1...dk
[Name] Select bit-image mode
[Format] ASCII ESC*m nL nH d1...dk
Hex 1B 2Am nL nH d1...dk
Decimal 27 42 m nL nH d1...dk
[Range] m = 0, 1, 32, 33
0 ≤ nL ≤ 255
0 ≤ nH ≤ 3
0 ≤ d ≤ 255
[Description] Selects a bit-image mode using m for the number of dots
specified by nL and nH,as follows:
m Mode Vertical Direction Horizontal Direction
Number Dot Dot Number of Data
ofDots Density Density (K)
0 8-dot single-density 8 67.7 dpi 101.6 dpi nL+ nH×256
1 8-dot double-density 8 67.7 dpi 203.2 dpi nL+ nH×256
32 24-dot single-density 24 203.2 dpi 101.6 dpi (nL+ nH×256)x3
33 24-dot double-density 24 203.2 dpi 203.2 dpi (nL+ nH×256)x3
[Notes] If the value of m is out of the specified range, nL and nH the
data following areprocessed as normal data.
The nL and nH indicate the number of dots in the bit image
in the horizontaldirection. The number of dots is calculated
by nL + nH x 256.

9
If the bit-image data input exceeds the number of dots to
be printed on a line,the excess data is ignored.
d indicates the bit-image data. Set a corresponding bit to 1
to print a dot or to 0not to print a dot.
After printing a bit image, the printer returns to normal data
processing mode.
This command is not affected by print modes (emphasized,
double-strike,underline, character size, or white/black
reverse printing), except upside-downprinting mode.
The relationship between the image data and the dots to be
printed is describedin Figure 3.11.3.
•When 8-dot bit image is selected:

3.11.3
• When 24-dot bit image is selected:

10
 3.11.3

11.ESC -n
[Name] Turn underline mode on/off
[Format] ASCII ESC -n
Hex 1B2D n
Decimal 27 45 n
[Range] 0 ≤ n ≤ 2, 48 ≤ n ≤ 50
[Description] Turns underline mode on or off, based on the following
values n：
n Function
0, 48 Turns off underline mode
1, 49 Turns on underline mode (1 dot thick)
2, 50 Turns on underline mode (2 dots thick)
[Notes] The printer can underline all characters (including right-side
character spacing),but cannot underline the space set by
HT.
The printer cannot underline 90°clockwise rotated
characters and white/blackinverted characters.
•When underline mode is turned off by setting the value of n
to 0 or 48, thefollowing data is not underlined, and the
underline thickness set before themode is turned off does

11
 not change. The default underline thickness is 1 dot.
•Changing the character size does not affect the current
underline thickness.
•Underline mode can also be turned on or off by using ESC !.
Note, however,that the last received command is effective.
[Default] n = 0
[Reference] ESC !

12.ESC 2
[Name] Select default line spacing
[Format] ASCII ESC 2
Hex 1B 32
Decimal 27 50
[Description] Selects 3.75 mm (30× 0.125 mm) line spacing.
[Notes] • The line spacing can be set independently in standard
mode.
[Reference] ESC 3

13.ESC 3n
[Name] Set line spacing
[Format] ASCIIESC 3 n
Hex 1B 33 n
Decimal 27 51 n
[Range] 0 ≤ n ≤ 255
[Description] Sets the line spacing to [n×0.125 mm].
[Notes] • The line spacing can be set independently in standard
mode.
• In standard mode, the vertical motion unit (y) is used.
[Default] n = 30
[Reference] ESC 2

14.ESC ?n
[Name] Cancel user-defined characters
[Format] ASCII ESC ? n
Hex 1B 3Fn
Decimal 2763 n
[Range] 32 ≤ n ≤ 126
[Description] Cancels user-defined characters.
[Notes] • This command cancels the patterns defined for the
character codesspecifiedby n. After the user-defined
characters are canceled, the correspondingpatterns for the
internal characters are printed.
• This command deletes the pattern defined for the

12
 specified code inthe fontselected by ESC !.
• If a user-defined characters have not been defined, the
printer ignores thiscommand.
[Reference] ESC &, ESC %

15.ESC @
[Name] Initialize printer
[Format] ASCII ESC @
Hex 1B 40
Decimal 27 64
[Description] Clears the data in the print buffer and resets the printer
mode to the mode thatwas in effect when the power was
turned on.
[Notes] • The DIP switch settings are not checked again.
• The data in the receive buffer is not cleared.

16.ESC D n1...nk NUL

[Name] Set horizontal tab positions
[Format] ASCII ESCD n1...nk NUL
Hex 1B 44 n1...nk 00
Decimal 27 68 n1...nk 0
[Range] 1 ≤ n ≤ 255
0 ≤ k ≤ 32
[Description] Sets horizontal tab positions.
• n specifies the column number for setting a horizontal t
ab position from thebeginning of the line.
• k indicates the total number of horizontal tab positions to
be set.
[Notes] • The horizontal tab position is stored as a value of
[character width x n]measured from the beginning of the
line. The character width includes theright-side character
spacing, and double-width characters are set with twice
thewidth of normal characters.
• This command cancels the previous horizontal tab
settings.
• When setting n = 8, the print position is moved to
column 9 by sending HT.
• Up to 32 tab positions (k = 32) can be set. Data
exceeding 32 tab positions isprocessed as normal data.
• Transmit [n]k in ascending order and place a NUL code
0 at the end.
When [n]k is less than or equal to the preceding value
[n]k-1, tab setting isfinished and the following data is

13
 processed as normal data.
• ESC D NUL cancels all horizontal tab positions.
• The previously specified horizontal tab positions do not
change, even if thecharacter width changes.
• The character width is memorized for each standard
mode.
[Default] The default tab positions are at intervals of 8 characters
(columns 9, 17, 25,...) forFont A (12×24).
[Reference] HT

17.ESC E n
[Name] Turn emphasized mode on/off
[Format] ASCII ESC E n
Hex 1B 45 n
Decimal 27 69 n
[Range] 0 ≤ n ≤ 255
[Description] Turns emphasized mode on or off
When the LSB of n is 0, emphasized mode is turned off.
When the LSB of n is 1, emphasized mode is turned on.
[Notes] • Only the least significant bit of n is enabled.
• This command and ESC ! turn on and off emphasized
mode in the same way.Be careful when this command is
used with ESC !.
[Default] n = 0
[Reference] ESC !

18.ESC Gn
[Name] Turn on/off double-strike mode
[Format] ASCII ESCGn
Hex 1B 47 n
Decimal 27 71 n
[Range] 0 ≤ n ≤ 255
[Description] Turns double-strike mode on or off.
• When the LSB of n is 0, double-strike mode is turned off.
• When the LSB of n is 1, double-strike mode is turned on.
[Notes] • Only the lowest bit of n is enabled.
• Printer output is the same in double-strike mode and in
emphasized mode.
[Default] n = 0
[Reference] ESC E

19.ESC Jn
[Name] Print and feed paper

14
 [Format] ASCII ESC J n
Hex 1B 4A n
Decimal 27 74 n
[Range] 0 ≤ n ≤ 255
[Description] Prints the data in the print buffer and feeds the paper [n×
0.125 mm (0.0049”)].
[Notes] • After printing is completed, this command sets the print starting
position to thebeginning of the line.
• The paper feed amount set by this command does not
affect the values set byESC 2 or ESC 3.
• In standard mode, the printer uses the vertical motion
unit (y).

20.ESC R n
[Name] Select an international character set
[Format] ASCII ESC R n
Hex 1B 52 n
Decimal 2782 n
[Range] 0 ≤ n ≤ 15
[Description] Selects international character set n from the following
table:
n Character set
0 U.S.A
1 France
2 Germany
3 U.K
4 Denmark I
5 Sweden
6 Italy
7 Spain I
8 Japan
9 Norway
10 Denmark II
11 Spain II
12 Latin America
13 Korea
14 Slovenia/Croatia
15 China
[Default] n = 0

21.ESC Vn
[Name] Turn 90° clockwise rotation mode on/off
[Format] ASCII ESC V n
15
 Hex 1B 56 n
Decimal 27 86 n
[Range] 0 ≤ n ≤ 1, 48 ≤ n ≤ 49
[Description] Turns 90° clockwise rotation mode on/off
n is used as follows:
n Function
0,48 Turns off 90° clockwise rotation mode
1,49 Turns on 90° clockwise rotation mode
[Notes] • This command affects printing in standard mode.
However, the setting isalways effective.
• When underline mode is turned on, the printer does not
underline 90°
clockwise-rotated characters.
• Double-width and double-height commands in
90° rotation mode enlargecharacters in the opposite
directions from double-height and double-
widthcommands in normal mode.
[Default] n = 0
[Reference] ESC !, ESC 

22.ESC v n
[Name] Transmit paper sensor status
[Format] ASCII ESC v n
Hex 1B 76 n
Decimal 27 118 n
[Description] The return value is 1 bytes ,It is a different on behalf of the
status：
Bit Off/On Hex Decimal Function
0 Off 00 0 Offline.
On 01 1 Online.
1 - - - Undefined.
2 Off 00 0 paper have.
On 04 4 paper out.
3 Off 00 0 Voltage is normal.
On 08 8 Voltage ＞9.5V.
4 - - - Undefined.
5 - - - Undefined.
6 Off 00 0 Temperature is normal.
On 40 64 Temperature ＞60°.
7 - - - Undefined.
For example：return “0x04” is means paper out.

16
23.ESC an
[Name] Select justification
[Format] ASCII ESC a n
Hex 1B 61 n
Decimal 27 97 n
[Range] 0 ≤ n ≤ 2, 48 ≤ n ≤ 50
[Description] Aligns all the data in one line to the specified position.
n selects the justification as follows:
n Justification
0,48 Left justification
1, 49 Centering
2, 50 Right justification
[Notes] • The command is enabled only when processed at the
beginning of the line instandard mode.
• This command executes justification in the printing area.
• This command justifies the space area according to HT,
ESC $ .
[Default] n = 0
[Example]

Left justification Centering Right justification

ABC ABC ABC
ABCD ABCD ABCD
ABCDE ABCDE ABCDE

24.ESC SOn
[Name] Select Double Width mode
[Format] ASCII ESCSOn
Hex 1B 0En
Decimal 27 14n
[Description] Select Double Width mode,
To turn double width off, use LF or DC4 command.

25.ESCDC4n
[Name] Disable Double Width mode
[Format] ASCII ESCDC4n
Hex 1B 14n
Decimal 27 20n
[Description] Disable Double Width mode

17
26.ESC d n
[Name] Print and feed n lines
[Format] ASCII ESC d n
Hex 1B 64 n
Decimal 27 100 n
[Range] 0 ≤ n ≤ 255
[Description] Prints the data in the print buffer and feeds n lines.
[Notes]• This command sets the print starting position to the beginning of the
line.
• This command does not affect the line spacing set by
ESC 2 or ESC 3.
• The maximum paper feed amount is 1016 mm (40
inches). If the paper feed amount (n x line spacing) of
more than 1016 mm (40 inches) is specified, theprinter
feeds the paper only 1016 mm (40 inches).
[Reference] ESC 2, ESC 3

27.ESC t n
[Name] Select character code table
[Format] ASCIIESC t n
Hex 1B 74 n
Decimal 27 116 n
[Range] 0 ≤ n ≤ 5, 16 ≤ n ≤ 19, n = 255
[Description] Selects page n from the character code table.
N Code Page N Code Page
0 CP437 [U.S.A., Standard Europe] 26 Thai
1 Katakana 27 CP720[Arabic]
2 CP850 [Multilingual] 28 CP855
3 CP860 [Portuguese] 29 CP857[Turkish]
4 CP863 [Canadian-French] 30 WCP1250[Central Eurpoe]
5 CP865 [Nordic] 31 CP775
6 WCP1251 [Cyrillic] 32 WCP1254[Turkish]
7 CP866 Cyrilliec #2 33 WCP1255[Hebrew]
8 MIK[Cyrillic /Bulgarian] 34 WCP1256[Arabic]
9 CP755 [East Europe，Latvian 2] 35 WCP1258[Vietnam]
10 Iran 36 ISO-8859-2[Latin 2]
11 reserve 37 ISO-8859-3[Latin 3]
12 reserve 38 ISO-8859-4[Baltic]
13 reserve 39 ISO-8859-5[Cyrillic]
14 reserve 40 ISO-8859-6[Arabic]
15 CP862 [Hebrew] 41 ISO-8859-7[Greek]
16 ＷCP1252 Latin I 42 ISO-8859-8[Hebrew]

18
 17 WCP1253 [Greek] 43 ISO-8859-9[Turkish]
18 CP852 [Latina 2] 44 ISO-8859-15 [Latin 3]
19 CP858 Multilingual Latin Ⅰ+Euro) 45 Thai2
20 Iran II 46 CP856
21 Latvian 47 Cp874
22 CP864 [Arabic]
23 ISO-8859-1 [West Europe]
24 CP737 [Greek]
25 WCP1257 [Baltic]
[Default] n = 0
[Reference] Character Code Tables

28.ESC { n
[Name] Turns on/off upside-down printing mode
[Format] ASCII ESC{ n
Hex 1B 7Bn
Decimal 27 123 n
[Range] 0 ≤ n ≤ 255
[Description] Turns upside-down printing mode on or off.
• When the LSB of n is 0, upside-down printing mode is
turned off.
• When the LSBof n is 1, upside-down printing mode is
turned on.
[Notes] • Only the lowest bit of n is valid.
• This command is enabled only when processed at the
beginning of a line instandard mode.
• In upside-down printing mode, the printer rotates the line
to be printed by 180°and then prints it.
[Default] n=0
[Example]

19
29.FS p n m
[Name] Print NV bit image
[Format] ASCII FS p n m
Hex 1C70 n m
Decimal 28 112 n m
[Range] 1 ≤ n ≤ 255
0 ≤ m ≤ 3 , 48 ≤ m ≤ 51
[Description] Prints NV bit image n using the mode specified by m.
m Mode Vertical Dot Density Horizontal Dot Density
0，48 Normal 203.2 dpi 203.2 dpi
1，49 Double-width 203.2 dpi 101.6 dpi
2，50 Double-height 101.6 dpi 203.2 dpi
3，51 Quadruple 101.6 dpi 101.6 dpi
• n is the number of the NV bit image (defined using the FS q
command).
• m specifies the bit image mode.
[Detail] • NV bit image is a bit image defined in non-volatile memory
byFS q and printed by FS p.
• This command is not effective when the specified NV bit
image has not beendefined.
• In standard mode, this command is effective only when
there is no data in theprint buffer.
• This command is not affected by print modes (emphasized,
underline, character size, white/black reverse printing, or
90° rotated characters,etc.), except upside-down printing
mode.
• If the downloaded bit-image to be printed exceeds one line,
the excess data isnot printed.
• This command feeds dots (for the height n of the NV bit
image) in normal anddouble-width modes, and (for the height
n x 2 of the NV bit image) in doubleheightand quadruple
modes, regardless of the line spacing specified by ESC 2or
ESC 3.
• After printing the bit image, this command sets the print
position to the beginningof the line and processes the data
that follows as normal data.
[References] ESC *, FS q, GS /, GS v

30.FS qn [xL xH yL yH d1...dk]1...[xL xH yL yH d1...dk]n

[Name] Define NV bit image
[Format] ASCII FS q n [xL xH yL yH d1...dk]1...[ xL xH yL yH d1...dk]n
Hex 1C 71 n [xL xH yL yH d1...dk]1...[ xL xH yL yH d1...dk]n

20
 Decimal28 113 n [xL xH yL yH d1...dk]1...[ xL xH yL yH
d1...dk]n
[Range] 1 ≤ n ≤ 255
0 ≤ xL ≤ 255
0 ≤ Xh≤ 3 (when 1 ≤ (xL xH x 256) ≤ 1023
0 ≤ yL ≤ 255
0 ≤ yL ≤ 1 (when 1 ≤ (yL yH x 256) ≤ 288
0 ≤ d ≤ 255
k = (xL xH x 256) x (yL yH x 256) x 8
Total defined data area = 192K bytes
[Description] Define the NV bit image specified by n.
• n specifies the number of the defined NV bit image.
• xL, xH specifies (xL xH x 256) x 8 dots in the
horizontal direction for the NV bitimage you are defining.
• yL, yH specifies (yL yH x 256) x 8 dots in the vertical
direction for the NV bitimage you are defining.
[Notes] • Frequent write command executions may damage the
NV memory.
Therefore, it is recommended to write the NV memory 10
times or less a day.
• The printer performs a hardware reset after the procedure
to place the imageinto the NV memory. Therefore,
user-defined characters, downloaded bitimages should be
defined only after completing this command.The printer
clears the receive and print buffers and resets the mode to
themode that was in effect at power on. (this version is not
support hardware reset )
• This command cancels all NV bit images that have
already been defined by thiscommand.
• From the beginning of the processing of this command
till the finish of hardwarereset, mechanical operations
(including initializing the position of the print headwhen the
cover is open, paper feeding using the FEED button, etc.)
cannot beperformed.
• During processing of this command, the printer is BUSY
when writing data tothe user NV memory and stops receiving
data. Therefore it is prohibited totransmit the data, including
real-time commands, during the execution of
thiscommand.
• NV bit image is a bit image defined in non-volatile
memory by FS q and printedby FS p.
• In standard mode, this command is effective only when
processed at thebeginning of the line.
• This command is effective when 7 bytes <FSyH> of the

21
 command areprocessed normally.
• When the amount of data exceeds the capacity left in the
range defined by xL,xH, yL, yH, the printer processes xL, xH,
yL, yH out of the defined range.
• In the first group of NV bit images, when any of the
parameters xL, xH, yL, yH isout of the definition range, this
command is disabled.
• In groups of NV bit images other than the first one, when
the printer encountersxL, xH, yL, yH out of the defined range,
it stops processing this command andstarts writing into the
NV images. At this time, NV bit images that haven’t
beendefined are disabled (undefined), but any NV bit
images before that areenabled.
• The dindicates the definition data. In data (d) a 1 bit
specifies a dot to beprinted and a 0 bit specifies a dot not to
be printed.
• This command defines n as the number of a NV bit
image. Numbers rise inorder from NV bit image 01H.
Therefore, the first data group [xL xH yL yHd1...dk] is NV bit
image 01H, and the last data group [xL xH yL yH d1...dk] is
NVbit image n. The total agrees with the number of NV bit
images specified by thecommand FS p.
• The definition data for an NV bit image consists of [xL xH
yL yH d1...dk].Therefore, when only one NV bit image is
defined n=1, the printer processes adata group [xL xH yL yH
d1...dk] once. The printer uses ([data: (xL xH× 256)×(yL
yH× 256)×8]   [header :4]) bytes of NV memory.
• The definition area in this printer is a maximum of 192K
bytes. This commandcan define several NV bit images, but
cannot define bit image data whose totalcapacity [bit
image data   header] exceeds 192K bytes.
• The printer does not transmit ASB status or perform
status detection duringprocessing of this command even
when ASB is specified.
• Once an NV bit image is defined, it is not erased by
performing ESC @, reset,and power off.
• This command performs only definition of an NV bit
image and does notperform printing. Printing of the NV bit
image is performed by the FS pcommand.
[Reference] FS p
[Example] 当xL = 64, xH = 0, yL = 96, yH = 0

22
31.GS ! n
[Name] Select character size
[Format] ASCII GS !n
Hex1D 21 n
Decimal 29 33 n
[Range] 0 ≤ n ≤ 255
(1 ≤ vertical number of times ≤ 8, 1 ≤ horizontal
number of times ≤ 8)
23
 [Description] Selects the character height using bits 0 to 2 and selects the
character
width usingbits 4 to 7, as follows:
Bit Off/On Hex Decimal Function
0 Character height selection. See Table 2.
1
2
3
4 Character width selection. See Table 1.
5
6
7

Table 1 Table 2
Character Width Selection Character Height Selection
Hex Decimal Width Hex Decimal Width
00 0 1(normal) 00 0 1(normal)
10 16 2(double-width) 01 1 2(double-height)
20 32 3 02 2 3
30 48 4 03 3 4
40 64 5 04 4 5
50 80 6 05 5 6
60 96 7 06 6 7
70 112 8 07 7 8
[Notes] • This command is effective for all characters
(alphanumeric and Kanji), exceptfor HRI characters.
• If n is outside the defined range, this command is
ignored.
• In standard mode, the vertical direction is the paper feed
direction, and thehorizontal direction is perpendicular to the
paper feed direction. However,when character orientation
changes in 90° clockwise-rotation mode, therelationship
between vertical and horizontal directions is reversed.
• When characters are enlarged with different sizes on one
line, all thecharacters on the line are aligned at the baseline.
• The ESC ! command can also turn double-width and
double-height modes onor off. However, the setting of the
last received command is effective.
[Default] n = 0
[Reference] ESC !

32.GS*x y d1...d(x xy x8)

[Name] Define downloaded bit image

24
 [Format] ASCIIGS * x y d1...d(x×y×8)
Hex 1D 2A xy d1...d(x×y ×8)
Decimal 29 42 x y d1 ...d(x×y×8)
[Range] 1 ≤ x ≤ 255
1 ≤ y ≤ 48 (where x×y ≤ 1536)
0 ≤ d ≤ 255
[Description] Defines a downloaded bit image using the number of dots
specified by x and y.
• x specifies the number of dots in the horizontal direction.
• y specifies the number of dots in the vertical direction.
[Notes] • The number of dots in the horizontal direction is x×8; in
the vertical direction itis y×8.
• If x×y is out of the specified range, this command is
disabled.
• The d indicates bit-image data. Data (d) specifies a bit
printed as 1 and notprinted as 0.
• The downloaded bit image definition is cleared when:
1) ESC @ is executed.
2) ESC &is executed.
3) Printer is reset or the power is turned off.
• The following figure shows the relationship between the
downloaded bit imageand the printed data.

[Reference] GS /

25
33.GS /m
[Name] Print downloaded bit image
[Format] ASCII GS / m
Hex 1D 2F m
Decimal 29 47 m
[Range] 0 ≤ m ≤ 3, 48 ≤ m ≤ 51
[Description] Prints a downloaded bit image using the mode specified by
m.
m selects a mode from the table below:
m Mode Vertical Dot Density Horizontal Dot Density
0, 48 Normal 203.2 dpi 203.2 dpi
1, 49 Double-width 203.2 dpi 101.6 dpi
2, 50 Double-height 101.6 dpi 203.2 dpi
3, 51 Quadruple 101.6 dpi 101.6 dpi
[Notes] • This command is ignored if a downloaded bit image has
not been defined.
• In standard mode, this command is effective only when
there is no data in theprint buffer.
• This command has no effect in the print modes
(emphasized, double-strike,underline, character size, or
white/black reverse printing), except for upsidedownprinting
mode.
• If the downloaded bit-image to be printed exceeds the
printable area, theexcess data is not printed.
[Reference] GS *

34.GS B n
[Name] Turn white/black reverse printing mode
[Format] ASCII GS B n
Hex 1D 42 n
Decimal 2966n
[Range] 0 ≤ n ≤ 255
[Description] Turns on or off white/black reverse printing mode.
• When the LSB of n is 0, white/black reverse mode is
turned off.
• When the LSB of n is 1, white/black reverse mode is
turned on.
[Notes] • Only the lowest bit of n is valid.
• This command is available for built-in characters and
user-defined characters.
• When white/black reverse printing mode is on, it also
applies to characterspacing set by ESC SP.

26
 • This command does not affect bit images, user-defined
bit images, bar codes,HRI characters, and spacing skipped
by HT, ESC $.
• This command does not affect the space between lines.
• White/black reverse mode has a higher priority than
underline mode. Even ifunderline mode is on, it is disabled
(but not canceled) when white/black reversemode is
selected.
[Default] n = 0

35.GS Hn
[Name] Select printing position for HRI characters
[Format] ASCII GSH n
Hex 1D 48n
Decimal29 72 n
[Range] 0 ≤ n ≤ 3, 48 ≤ n ≤ 51
[Description] Selects the printing position of HRI characters when printing
a bar code.n selects the printing position as follows:
n Printing position
0, 48 Not printed
1, 49 Above the bar code
2, 50 Below the bar code
3, 51 Both above and below the bar code
• HRI indicates Human Readable Interpretation.
[Notes] • HRI characters are printed using the font specified by GS
f.
[Default] n = 0
[Reference] GS f, GS k

36.GS L nL nH
[Name] Set left margin
[Format] ASCII GS LnL nH
Hex 1D 4C nL nH
Decimal 29 76 nLnH
[Range] 0 ≤ nL ≤ 255
0 ≤ nH ≤ 255
[Description] Sets the left margin using nL and nH.
• The left margin is set to [(nL + nH ×256) × 0.125
mm].

27
 [Notes] • This command is effective only when processed at the
beginning of the line instandard mode.
• If the setting exceeds the printable area, the maximum
value of the printablearea is used.
[Default] nL = 0, nH = 0

37.GS a n
[Name] Enable/Disable Automatic Status Back (ASB)
[Format] ASCII GS a n
Hex 1D 61 n
Decimal 29 97 n
[Range] 0 ≤ n ≤ 255
Value
Bit Function
0 1
0 - - -
1 - - -
2 Disable/Enable ASB Disable Enable
3-4 - - -
5 Disable/Enable RTS as flow control Disable Enable
6-7 - - -
[Description] When ASB is enabled, the printer will send the changed
status to PC automatically.

38.GS h n
[Name] Select bar code height
[Format] ASCII GS h n
Hex 1D 68 n
Decimal 29 104 n
[Range] 1 ≤ n ≤ 255
[Description] Selects the height of the bar code.
n specifies the number of dots in the vertical direction.
[Default] n = 162
[Reference] GS k

39.GS k m d1...dk NUL/GS k m n d1...dn

[Name] Print bar code
[Format] ①ASCII GS km d1...dk NUL
28
 Hex 1D 6B m d1...dk 00
Decimal 29 107m d1...dk 0
②ASCII GS k m n d1...dn
Hex 1D 6Bm n d1...dn
Decimal29 107m n d1...dn
[Range] ①0 ≤ m ≤ 6 (k and d depend on the bar code system
used)
②65 ≤m ≤ 73 (n and d depend on the bar code system
used)
[Description] Selects a bar code system and prints the bar code.
m selects a bar code system as follows:
m Bar Code System Number of Characters Remarks
① 0 UPC-A 11 ≤ k ≤ 12 48 ≤ d ≤ 57
1 UPC-E 11 ≤ k ≤ 12 48 ≤ d ≤ 57
2 JAN13 (EAN13) 12 ≤ k ≤ 13 48 ≤ d ≤ 57
3 JAN 8 (EAN8) 7 ≤ k ≤ 8 48 ≤ d ≤ 57
4 CODE39 1 ≤ k′ 48 ≤ d ≤ 57, 65 ≤ d
≤ 90, 32, 36, 37,43, 45, 46,
47
5 ITF 1 ≤ k (even number) 48 ≤ d ≤ 57
6 CODABAR 1 ≤ k′ 48 ≤ d ≤ 57, 65 ≤ d
≤ 68 , 36, 43, 45,46, 47, 58
② 65 UPC-A 11 ≤ n≤ 12 48 ≤ d ≤ 57
66 UPC-E 11 ≤ n≤ 12 48 ≤ d ≤ 57
67 JAN13 (EAN13) 12 ≤ n ≤ 13 48 ≤ d ≤ 57
68 JAN 8 (EAN8) 7 ≤ n≤ 8 48 ≤ d ≤ 57
69 CODE39 1 ≤ n ≤ 255 48 ≤ d ≤ 57, 65 ≤ d
≤ 90, 32, 36, 37,43, 45, 46,
47
70 ITF 1 ≤ n ≤ 255 (even 48 ≤ d ≤ 57
number)
71 CODABAR 1 ≤ n ≤ 255 48 ≤ d ≤ 57, 65 ≤ d
≤ 68 , 36, 43, 45,46, 47, 58
72 CODE93 1 ≤ n ≤ 255 0 ≤ d ≤ 127
73 CODE128 2 ≤ n ≤ 255 0 ≤ d ≤ 127
[Notes for ①]
• This command ends with a NUL code.
• When the bar code system used is UPC-A or UPC-E, the
printer prints the barcode data after receiving 12 bytes of
bar code data and processes the followingdata as normal
data.
• When the bar code system used is JAN13 (EAN13), the
printer prints the barcode after receiving 13 bytes of bar

29
 code data and processes the following dataas normal data.
• When the bar code system used is JAN8 (EAN8), the
printer prints the bar codeafter receiving 8 bytes of bar code
data and processes the following data asnormal data.
• The number of data for the ITF bar code must be even
numbers. When an oddnumber of bytes of data is input, the
printer ignores the last received data.
[Notes for ②]
• n indicates the number of bar code data bytes, and the
printer processes nbytes from the next character data as bar
code data.
• If n is outside the specified range, the printer stops
command processing andprocesses the following data as
normal data.
[Notes in standard mode]
• If d is outside the specified range, the printer only feeds
paper and processesthe following data as normal data.
• If the horizontal size exceeds printing area, the printer
only feeds the paper.
• This command feeds as much paper as is required to
print the bar code,regardless of the line spacing specified
by ESC 2 or ESC 3.
• This command is enabled only when no data exists in the
print buffer.Whendata exists in the print buffer, the printer
processes the datafollowing m asnormal data.
• After printing the bar code, this command sets the print
position to thebeginning of the line.
• This command is not affected by print modes
(emphasized, double-strike,underline, character size,
white/black reverse printing, or 90° rotated character,etc.),
except for upside-down printing mode.
Control character Control character
ASCII Hex Decimal HRI character ASCII Hex Decimal HRI character
NUL 00 0 ■U DEL 10 16 ■P
SOH 01 1 ■A DC1 11 17 ■Q
STX 02 2 ■B DC2 12 18 ■R
ETX 03 3 ■C DC3 13 19 ■S
EOT 04 4 ■D DC4 14 20 ■T
ENQ 05 5 ■E NAK 15 21 ■U
ACK 06 6 ■F SYN 16 22 ■V
BEL 07 7 ■G ETB 17 23 ■W
BS 08 8 ■H CAN 18 24 ■X
HT 09 9 ■I EM 19 25 ■Y
LF 0A 10 ■J SUB 1A 26 ■Z
30
VT 0B 11 ■K ESC 1B 27 ■A
FF 0C 12 ■L FS 1C 28 ■B
CR 0D 13 ■M GS 1D 29 ■C
SO 0E 14 ■N RS 1E 30 ■D
SI 0F 15 ■O US 1F 31 ■E
DEL 7F 127 ■T
[Example] Printing GS k 72 7 67 111 100 101 13 57 51

When CODE128 (m = 73) is used:

• When using CODE128 in this printer, take the following
points into account fordata transmission:
① The top of the bar code data string must be the code
set selection character(CODE A, CODE B, or CODE C),
which selects the first code set.
② Special characters are defined by combining two
characters "{" and onecharacter. The ASCII character "{" is
defined by transmitting "{" twiceconsecutively.
Transmit data
Specific character ASCII Hex Decimal
SHIFT {S 7B, 53 123,83
CODE A {A 7B, 41 123,65
CODE B {B 7B,42 123,66
CODE C {C 7B,43 123,67
FNC1 {1 7B,31 123,49
FNC2 {2 7B,32 123,50
FNC3 {3 7B,33 123,51
FNC4 {4 7B,34 123,52
"{" {{ 7B,7B 123,123
[Example] Example data for printing "No. 123456"
In this example, the printer first prints "No." using CODE B, then
prints thefollowing numbers using CODE C.
GS k 73 10 123 66 78 111 46 123 67 12 34 56

• If the top of the bar code data is not the code set

31
 selection character, the printerstops command processing
and processes the following data as normal data.
• If the combination of "{" and the following character
does not apply any specialcharacter, the printer stops
command processing and processes the followingdata as
normal data.
• If the printer receives characters that cannot be used in
the special code set,the printer stops command processing
and processes the following data asnormal data.
• The printer does not print HRI characters that correspond
to the shift charactersor code set selection characters.
• HRI character for the function character is space.
• HRI characters for the control character (<00>H to
<1F>H and <7F>H) arespace.
<Others> Be sure to keep spaces on both right and left sides of a bar
code. (Spaces aredifferent depending on the types of the
bar code.)
[Reference] GS H, GS h, GS w

40.GS xn
[Name] Set barcode printing left space
[Format] ASCIIGSx n
Hex 1D 78n
Decimal 29 120n
[Description] The print bar code staring positions is: 0255

41.GS r n
[Name] Transmit status
[Format] ASCII GS r n
Hex 1D 72 n
Decimal 29 114 n
[Range] n = 1, 49
[Description] Transmits the status specified by n as follows:
n Function
1, 49 Transmits paper sensor status
[Notes] • When using a serial interface
When DTR/DSR control is selected, the printer transmits
only 1 byte afterconfirming the host is ready to receive data
(DSR signal is SPACE). If the hostcomputer is not ready to
receive data (DSR signal is MARK), the printer waitsuntil the
host is ready.
When XON/XOFF control is selected, the printer transmits
only 1 byte withoutconfirming the condition of the DSR

32
 signal.
• This command is executed when the data in the receive
buffer is developed.Therefore, there may be a time lag
between receiving this command andtransmitting the status,
depending on the receive buffer status.
• When Auto Status Back (ASB) is enabled using GS a, the
status transmitted byGS r and the ASB status must be
differentiated using.
• The status types to be transmitted are shown below:
Paper sensor status (n = 1, 49):
Bit Off/On Hex Decimal Status for ASB
0,1 - - - Undefined.
2,3 Off 00 0 Paper roll end sensor: paper adequate.
On (0C) (12) Paper roll end sensor: paper near end.
4 Off 00 0 Not used. Fixed to Off.
5,6 - - - Undefined.
7 Off 00 0 Not used. Fixed to Off.
Bits 2 and 3: When the paper end sensor detects a paper end, the printer
goes offline and doesnot execute this command. Therefore,
bits 2 and 3 do not transmit the status ofpaper end.
[Reference] GS a

42.GS v 0 m xL xH yL yHd1....dk
[Name] Print raster bit image
[Format] ASCII GS v 0 m xL xH yL yH d1...dk
Hex 1D 76 30 m xL xH yL yH d1...dk
Decimal 29 118 48 m xL xH yL yH d1...dk
[Range] 0 ≤m ≤ 3, 48 ≤m ≤ 51
0 ≤ xL ≤ 255
0 ≤ xH ≤ 255 where 1 ≤ (xL + xH×256) ≤ 48
0 ≤ yL ≤ 255
0 ≤ yH ≤ 8 where 1 ≤ (yL + yH×256) ≤ 4095
0 ≤ d ≤255
k = (xL + xH×256) ×(yL + yH× 256) (k ≠0)
[Description] Selects raster bit-image mode. The value of m selects the
mode, as follows:
m Mode Vertical Horizontal
Dot Density Dot Density
0, 48 Normal 203.2 dpi 203.2 dpi
1, 49 Double-width 203.2 dpi 101.6 dpi
2, 50 Double-height 101.6 dpi 203.2 dpi
3, 51 Quadruple 101.6 dpi 101.6 dpi
• xL, xH, select the number of data bytes (xL+xH×256) in

33
 the horizontal direction for thebit image.
• yL, yH, select the number of data bits (yL+yH×256) in the
vertical direction for the bitimage.
[Notes] • In standard mode, this command is effective only when
there is no data in theprint buffer.
• This command is not affected by print modes (character
size, emphasized,double-strike, upside-down, underline,
white/black reverse printing, etc.) forraster bit image.
• Data outside the printing area is read in and discarded on
a dot-by-dot basis.
• The position at which subsequent characters are to be
printed for raster bitimage is specified by HT (Horizontal
Tab), ESC $ (Set absolute print position), and GS L (Set left
margin ). If the position atwhich subsequent characters are
to be printed is a multiple of 8.
• The ESC a (Select justification) setting is also effective on
raster bit images.
• d indicates the bit-image data. Setting a bit to 1 prints a
dot and setting it to 0does not print a dot.
[Example] When xL+xH×256=64
← (xL+ xH×256)×8dots=512dots →
1 2 3 **** * 62 63 64 ↑
65 66 67 **** * 126 127 128
**** * yL+yH256dots
**** * K-2 K-1 K ↓

7 6 5 4 3 2 1 0
MSBLSB

43.GS w n
[Name] Set bar code width
[Format] ASCII GS w n
Hex 1D 77 n
Decimal 29 119 n
[Range] 2 ≤ n ≤ 6
[Description] Sets the horizontal size of the bar code.
n specifies the bar code width as follows:
n Module Width (mm) for Binary-level Bar Code
Multi-level Bar Code Thin Element Width (mm) Thick Element Width(mm)
2 0.250 0.250 0.625
3 0.375 0.375 1.000

34
 4 0.560 0.500 1.250
5 0.625 0.625 1.625
6 0.750 0.750 2.000
• Multi-level bar codes are as follows:
UPC-A, UPC-E, JAN13 (EAN13), JAN8 (EAN8), CODE93,
CODE128
• Binary-level bar codes are as follows:
CODE39, ITF, CODABAR
[Default] n = 3
[Reference] GS k

44.FS ! n
[Name] Set print mode(s) for Kanji characters
[Format] ASCII FS ! n
Hex 1C 21 n
Decimal 28 33 n
[Range] 0 ≤ n ≤ 255
[Description] Sets the print mode for Kanji characters, using n as follows:
Bit Off/On Hex Decimal Function
0 － － － Undefined.
1 － － － Undefined.
2 Off 00 0 Double-width mode is OFF.
On 04 4 Double-width mode is ON.
3 Off 00 0 Double-height mode is OFF.
On 08 Double-height mode is ON.
4 － － － Undefined.
5 － － － Undefined.
6 － － － Undefined.
7 Off 00 0 Underline mode is OFF.
On 80 128 Underline mode is ON.
[Notes] • When both double-width and double-height modes are
set (including
right- andleft-side character spacing), quadruple-size
characters areprinted.
•The printer can underline all characters (including right-
and left-side characterspacing), but cannot underline the
space set by HT and 90° clockwise-rotatedcharacters.
• When some of the characters in a line are double or more
height, all thecharacters on the line are aligned at the
baseline.
• It is possible to emphasize the Kanji character using GS !;
the settingof the last received command is effective.
[Default] n = 0

35
 [Reference] GS !

45.FS &
[Name] Select Kanji character mode
[Format] ASCII FS &
Hex 1C 26
Decimal 28 38
[Description] Selects Kanji character mode.
[Notes] For Kanji model:
• When the Kanji character mode is selected, the printer
processes all Kanjicodeas two bytes each.
• Kanji codes are processed in the order of the first byte
and second byte.
• Kanji character mode is not selected when the power is
turned on.
[Reference] FS .

46.FS .
[Name] Cancel Kanji character mode
[Format] ASCII FS .
Hex 1C 2E
Decimal 28 46
[Description] Cancels Kanji character mode.
[Notes] For Kanji model:
• When the Kanji character mode is not selected, all
character codes areprocessed one byte at a time as ASCII
code.
• Kanji character mode is not selected when the power is
turned on.
[Reference] FS &

47.ESC = n
[Name] Set peripheral device
[Format] ASCII ESC = n
Hex 1b 3d n
Decimal 27 61 n
[Description] Set peripheral device：
Bit Off/On Hex Decimal Function
0 Off 00 0 Printer offline，not receive print data.
On 01 1 Printer online， receive print data.
1-7 - - - Undefined.

36
48.ESC7n1n2n3
[Name] Setting Control Parameter Command
[Format] ASCII ESC7 n1n2 n3
Hex 1B 37 n1 n2 n3
Decimal 27 55n1 n2 n3
[Description] Set “max heating dots”,”heating time”, “heating interval” ;
n1 = 0-255 Max printing dots，Unit(8dots)，Default:9(80
dots);
n2 = 3-255 Heating time，Unit(10us),Default:80(800us);
n3 = 0-255 Heating interval,Unit(10us)，Default:2(20us);
The more max heting dots, the more peak current will cost
whenprinting, the faster printing speed. The max heating
dots is 8*(n1+1);
The more heating time, the more density , but the slower
printing speed. If heating time is too short, blank page may
occur.
The more heating interval, the more clear, but the slower
printingspeed.

49.ESC 8n1n2
[Name] Sleep parameter
[Format] ASCII ESC8n1 n2
Hex 1B 38 n1 n2
Decimal 27 56 n1 n2
[Description] Setting the time for control board to enter sleep mode.
n1+n2*256 The time waiting for sleep after printing finished，
Unit(Second)，Default:0(don’t sleep)
When control board is in sleep mode, host must send one
byte(0xff) to wake up control board. And waiting 50ms, then
send printing command and data.
NOTE：The command is useful when the system is powered by battery.

50.ESC 9n
[Name] Select Chinese code format
[Format] ASCII ESC9 n
Hex 1B 39 n
Decimal 27 57 n
[Description] Select Chinese code format, n from the character code table
as follows：
0:GBK code
1:UTF-8 code
3:BIG5 code

37
 NOTE：This version is not support English.

51.DC2 T
[Name] Printing test page
[Format] ASCII DC2 T
Hex 12 54
Decimal 18 94
[Description] Printing test page

52.ESC pm t1 t2(for Drawer)

[Name] Generate pulse
[Format] ASCII ESC p m t1 t2
Hex 1B 70 m t1 t2
Decimal 27 112 m t1 t2
[Range] m=0,1,48,49
0 ≤ t1≤ 255, 0≤ t2≤ 255
[Description] Outputs the pulse specified by t1 to connector pin m as follows:
m Function
0,48 Drawer kick-out connector pin2.
1,49 Drawer kick-out connector pin5.
[Notes] • The pulse ON time is [t1×2ms] and the OFF time is[t2×
2ms].
•If t2<t1,the OFF time is [t1×2ms].

53.ESC un (for Drawer)

[Name] Transmit peripheral device status
[Format] ASCII ESC u n
Hex 1B 75 n
Decimal 27 117 n
[Range] 0  
[Description] transmits the status of the drawer kick-out connector pin 3
as 1byte of data when n=0,48.this allows the host to
determine the status of a peripheral device.
n is used as follows:
Bit On/off Hex Decimal Function
0 Off 00 0 Drawer kick out connector pin 3 is low
0 On 01 1 Drawer kick out connector pin 3 is high
1-3 - - - Undefined
4 Off 00 0 Not used. Fixed to off
5-6 - - - Undefined
7 Off 00 0 Not used. Fixed to off

38
54.ESC c 5 n(for buttons)
[Name] Enable/disable panel buttons
[Format] ASCII ESC c 5 n
Hex 1B 63 35 n
Decimal 27 9953 n
[Range] 0 ≤ n ≤ 255
[Description] Enables or disables the panel buttons.
• When the LSB of n is 0, the panel buttons are enabled.
• When the LSB of n is 1, the panel buttons are disabled.
[Default] n = 0

39