Scribd
Upload
68 views

DF NMK508WebInstallationManual

The document provides installation and maintenance instructions for a pull-down kitchen faucet. It lists recommended tools and materials, safety steps to take before installation like shutting off water, and installation steps like connecting supply lines and attaching the weight. It also provides a parts list and warns that abrasive cleaners should be avoided to maintain the faucet's finish.

Uploaded by

James Loewen
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
68 views

DF NMK508WebInstallationManual

The document provides installation and maintenance instructions for a pull-down kitchen faucet. It lists recommended tools and materials, safety steps to take before installation like shutting off water, and installation steps like connecting supply lines and attaching the weight. It also provides a parts list and warns that abrasive cleaners should be avoided to maintain the faucet's finish.

Uploaded by

James Loewen
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

DF-NMK508 – RV Pull-Down Kitchen Faucet

MAINTENANCE AND CLEANING

Cleaning Tips: The finish on your product is designed to retain its beautiful sheen for
years. To maintain the original look of the finish, a little care and caution should be
used. We recommend the use of mild soap and water to clean the product.

THE USE OF ABRASIVE CLEANERS MAY SCRATCH THE FINISH OR CAUSE OTHER
DAMAGE.

RECOMMENDED TOOLS AND MATERIALS

¨ Adjustable Wrench
¨ Plumbers Tape (Thread Seal Tape)
¨ Phillips Screw Driver

BEFORE YOU BEGIN

There are a variety of things to do before installing any new plumbing system into your
RV. Before you begin work make sure you:

¨ Shut off the main water supply


¨ Cover your drain to prevent loss of parts
¨ Observed any local plumbing codes
¨ Inspect fixture for damage - Replace as necessary

* Dura Faucet reserves the right to make any revisions in the design of products without
notice.
INSTALLATION OF THE FAUCET

1 New Faucet Preparation

First, shut off the water supply and remove the old faucet by disconnecting it from the
supply lines under the sink, and unscrewing the faucet from the countertop by removing
mounting nuts. Next, clean the sink’s top surface in preparation for the new faucet.

2 Fastening Deck Plate (Optional)

Install the faucet spout through the hole in the sink/counter top. Slide washers to the
threaded collar followed by the mounting nut. Thread the mounting nut to the
underside of the sink and tighten.

3 Secure Faucet

Remove the lock-nut provided. Place the faucet on sink top and feed hoses down
through the center hole in the sink. Next, from below the sink, secure the faucet by re-
attaching the lock-nut (A) and screwing it down with the 2 set screws until tight (B/C).
4 Connect Supplies

Securely attach marked supply lines with corresponding hot (A) and cold (B) hoses
from the faucet. Tighten all connections with wrench to ensure that no leaking occurs.
With all connections plumber’s tape can be utilized to help reduce the risk of leaking.
5 Install Metal Weight

Attach the weight to the hose at a length suitable to you (the further from the end you
place the weight the longer your reach will be when pulling the hose out for use). You
may move the weight to adjust the pull-down length of the hose. Carefully tighten the
weight

6 Flush Lines

Once installation of the hoses is complete, remove the spray head. Turn the water supply
on and allow both hot and cold water to run for at least 30 to 60 seconds each. While
water is running, check for leaks around and under the sink. Once done replace aerator
and start enjoying your new Dura Faucet.
SPEC DRAWING / PARTS

1. Handle Assembly
2. Cap (1)
3. Adjusting (1)
4. Ceramic Disc Cartridge
5. Shower Head
6. Spout
7. Above Cover
8. Base
9. Body Assembly
10. Stainless Tube
11. Packing
12. Lock Nut
13. Sleeve
14. Weight Assembly

You might also like