Approx

Dash L P S
Weight
Length IN(MM) IN(MM) IN(MM)
LB(KG)**
-1 59.15 47 23X1 62
DWG PART
QTY DESCRIPTION MATERIAL (1502) (1194) (584) (28)
REF NUMBER
SHELL 99.15 87 56X1 75
Filament Wound Epoxy/Glass composite - -2
1 1 99218 SHELL Head locking grooves integrally wound in
(2518) (2210) (1422) (34)
place. 139.15 127 80X1 87
2 A/R A/R F/C Port SA-351 CF3M -3
(3534) (3226) (2032) (39)
3 A/R A/R F/C Port Seal Ethylene Propylene.
179.15 167 64X2 100
HEAD -4
4 2 194448 Bearing Plate Assembly -
(4550) (4242) (1626) (45)
4.1 1 96156 Bearing Plate SB-221 A96061-T6 219.15 207 78X2 112
-5
4.2 1 97105 Danger Label - (5566) (5258) (1981) (51)
5 2 96160 Sealing Plate Engineering Thermoplastic. 259.15 247 92X2 125
-6
6 2 96162 Permeate Port Engineering Thermoplastic. (6582) (6274) (2337) (57)
7 2 45066 Port Nut Engineering Thermoplastic.
299.15 287 106X2 136
8 2 96000 Head Seal Ethylene Propylene - O - Ring -7
(7598) (7290) (2692) (62)
9 2 45312 Perm Port Seal Ethylene Propylene - O - Ring
339.15 327 120X2 148
HEAD INTERLOCK -8
10 2 47336 Quick Release Spiral Ring SA-479 316
(8614) (8306) (3048) (67)
VESSEL SUPPORT
11 2+ 52169 Saddle Engineering Thermoplastic.
12 2+ 45042 Strap Assy. 304 Stainless Steel-PVC Cushion.
13 4++ 46265 Strap screw. 5/16-18 UNC, 2.5''-L,18-8 Stainless Steel.

ELEMENT INTERFACE
14 2 A/R Adapter Engineering Thermoplastic.
15 2 52245 Adapter seal Ethylene Propylene - O - Ring
16 4 A/R PWT Seal Ethylene Propylene - O - Ring
17 1 96163 Thrust Cone Engineering Thermoplastic.
+ ++
3& 6 each furnished with length code 4,5,6,7 & 8.
 ORDERING:
RATING: PRECAUTIONS: Using the chart below, please check the features you require
DO…read, understand and follow all instructions; failure to take
DESIGN PRESSURE……….………....................300 PSIG VESSEL LENGTH CODE – please check one
every precaution will void warranty and may result in vessel
(2.07 MPa) failure MODEL 80S30  -1  -2  -3  -4  -5  -6  -7  -8
MAX. OPERATING TEMP…………...………...…..190°F DO…mount the shell on horizontal members at span “ S” using
(88°C) compliant vessel supports furnished; Shim saddles if MEMBRANE BRAND AND MODEL
MIN. OPERATING TEMP…………...………..…...…20°F required. Tighten hold down straps just snug  Please supply adapters for the following membrane brand and specific model
(-7°C) DO…align and center side ports with the manifold header.
Brand_________________________ Model_______________________
FACTORY TEST PRESSURE…....………...…CE/ ASME Correct, causes of misalignment in a row of vessels
450 PSIG /330 PSIG connected to the same header
CERTIFICATION REQ UIRED
(3.1 MPa)/(2.3 MPa) DO…use flexible type IPS grooved-end pipe couplings, at side
QUALIFICATION PRESSURE ………..……......1800 PSI ports; allow full, 0.125 inch gap between port and piping,  Hydro testing at 1.1 times the design pressure.
(12.4 MPa) and position piping to maximize flexibility of connection.  ASME Stamped and National Board Registered.
INTENDED USE: DO…provide flexibility in, and support for piping manifolds so  In compliance with the ASME Sec X but not Code Stamped.
The CodeLine 80S30 Fiberglass RO Pressure Vessel is that vessel can grow in length under pressure without undue
designed for continuous, long term use as housing for restraint; provide additional flexible joints in large pipes  Hydro testing at 1.5 times the design pressure.
reverse osmosis membrane elements to desalt typical leading to manifold header.  CE Marked. ADAPTER KITS
brackish waters at pressures up to 300 psi. Any make of DO…provide overpressure protection for vessel set at not more UP DOWN
eight-inch nominal diameter spiral-wound element is easily than 105% of design pressure PERMEATE PORT SELECTION
STREAM STREAM
accommodated; the appropriate interfacing hardware for the DO…inspect end closures regularly; replace components that Serial Number End
element specified is furnished with the vessel. have deteriorated and correct causes of corrosion
DO… Lubricate seals sparingly, using nonpetroleum Size of the Permeate Port  1”  1.25”  1.5”
The CodeLine 80S30 is designed in accordance with the based lubricants, i.e. Glycerin or suitable lubricants.
Type of Connection  FNPT  MNPT  BSPTM  BSPTF  IPS GROOVED  TRICLOVER
engineering standards of the Boiler and Pressure Vessel
Code of the American Society of Mechanical Engineers DO NOT…work on any component until first verifying that
Material of Construction  Noryl  SS316L  Zeron 100
(ASME) as per Section X Edition 2019 and F/C port, pressure is relieved from vessel
Bearing plate and Quick release spiral ring are designed as DO NOT…make rigid piping connections to ports or clamp Non Serial Number End
per Section VIII Division I Edition 2019. vessel in any way that resists growth of fiberglass shell under
pressure; Size of the Permeate Port  1”  1.25”  1.5”
At small additional cost vessels can be inspected during ***ΔDIA = 0.015 in. (0.4mm) and Type of Connection  FNPT  MNPT  BSPTM  BSPTF  IPS GROOVED  TRICLOVER
construction by an ASME Authorized Inspector and ASME ***ΔL = 0.2 in. (5mm) for a length code –8 vessel
Code stamped. DO NOT… hang piping manifolds from ports or use vessel in Material of Construction  Noryl  SS316L  Zeron 100
any way to support other components
The CodeLine 80S30 must be installed, operated and DO NOT…tighten Permeate Port connection more than one turn Note:
maintained in accordance with the listed precautions and past hand tight  Standard offering is 1.0” FNPT in Noryl.
good industrial practice to assure safe operation over a long DO NOT… operate vessel without connecting both Permeate  1.25” & 1.5” BSPTF,1.25” & 1.5” FNPT and 1.25” TRICLOVER connections cannot be offered
service life. Ports internally to complete set of elements or otherwise plug  Triclover permeate port cannot be offered in Noryl
ports internally so that external piping connection is not
The high performance Filament wound FRP shell must be
subjected to feed pressure STRAP ASSEMBLY
allowed to expand under pressure; undue restraint at  SS304  SS316  SS316L
DO NOT…install Spacer on downstream end of vessel
support points or piping connections can cause leaks to
DO NOT…operate vessel without Thrust Cone installed
develop in the shell. This side-ported vessel requires special FEED/CONCENTRATE PORT SELECTION
downstream
precautions in mounting and connection to piping so that
DO NOT…pressurize vessel until double-checking to verify that Material of Construction  CF3M  Duplex (CD3MN)
the vessel will not be subjected to excessive stress due to
bending moments acting at the side openings in the the Locking Ring is in place and fully seated.  Super Duplex (CD3MWCuN)
DO NOT…operate vessel at pressure and temperature in excess
fiberglass shell. The end closure, incorporating close fitting,
interlocking metal components, must be kept dry and free of its rating. Configuration  - CF3M 1D5D
DO NOT…operate vessel with permeate pressure in excess of  – Multi ports :( Refer SPEC.SHEET/PM/1.5”-3”for Multi port selection)
of corrosion; deterioration can lead to catastrophic
125 psi at 190°F (0.86 Mpa at 88 0 C). PP

mechanical failure of the head. PP

Pentair will assist the purchaser in determining the

DO NOT…tolerate leaks or allow end closures to be routinely
wetted in any way
Serial number end 
suitability of this standard vessel for their specific operating
conditions. The final determination however, including
DO NOT…operate outside the pH range 3-11. Opposite end  D
PORT SIZE CODE
1½” GROOVED END
evaluation of the standard material of construction for For complete information on proper use of the vessel
BEARING PLATE MATERIAL 2” GROOVED END
compatibility with the specific corrosive environment, shall Please refer to the 80S Series USER’S GUIDE 94182. E
be the responsibility of the purchaser. Alternate materials  – A96061 T6 Aluminium
with enhanced corrosion resistance are available on special  – Stainless Steel 316L F 2½” GROOVED END
order.

Specifications are subject to change without notice. Note: Please refer to 99321 for triclover details and refer page-3 for optional Part numbers.

DWG. NO. 99160-Z. © PENTAIR PAGE 2 OF 3.

 BEARING PLATE PART NUMBERS
SEALING PLATE PART NUMBERS
PERMEATE PORT SIZE ALUMINIUM SS F316L ###
1.0"/1.25" 194448 194510 Standard used for Aluminium BP 96160
1.5" 194479 194541 Optional used for SS316L BP 96477

PERM PORT RETAINER RING & PORT NUT PART STRAP ASSEMBLY PART NUMBERS
NUMBERS
1.0" / 1.25" Standard Port nut 45066
SS304 SS316 SS316L
+
1.5" Port Retainer Ring 45247 45042 46926 94371+

F/C PORT & SEAL PART NUMBER

SIZE *CF3M **CD3MN ***CD3MWCuN SEAL

1.5" 98024 97353 96507 96077

2.0" 98025 97357 96643 96078
2.5" 98026 97364 96556 96079

PERMEATE PORT PART NUMBERS & PERMPORT TO F/C PORT OFFSET DISTANCE
FNPT MNPT BSPTF BSPTM IPS GROOVED
SIZE MATERIAL PART PART PART PART PART
NUMBER DIM "A" NUMBER DIM "A" NUMBER DIM "A" NUMBER DIM "A" NUMBER DIM "A"
NORYL 96162 5.5 97659 6.5 96301 5.5 97660 6.5 97661 6.8
1.0" SS316L # # 96752 5.5 97347 6.5 97351 5.5 97355 6.5 97322 6.8
#
ZERON 100 97349 5.5 97348 6.5 97352 5.5 97356 6.5 97293 6.8
NORYL NA NA 97655 6.5 NA NA 97360 6.5 97662 6.8
1.25" SS316L # # NA NA 96487 6.5 NA NA 97362 6.5 97311 6.8
#
ZERON 100 NA NA 97359 6.5 NA NA 97363 6.5 97365 6.8
NORYL NA NA 97663 6.1 NA NA 97369 6.1 97656 6.7
1.5" SS316L # # NA NA 97368 6.1 NA NA 97371 6.1 97449 6.7
#
ZERON 100 NA NA 97292 6.1 NA NA 97372 6.1 97374 6.7