-|Transparent Guide|-

TCD210185AB Ordering Information

This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.

P S A N - ❶ ❷ ❸ ❹ ❺ - ❻
❶ Medium / Port fitting position ❹ Control output

Display Type
No mark: Pneumatic type (gas) / Back No mark: NPN open collector output
D: Pneumatic type (gas) / Bottom P: PNP open collector output
B: Fluid type (liquid, gas) / Back

Pressure Sensors
❺ Option input / output
L: Fluid type (liquid, gas) / Bottom
V: Voltage output
❷ Pressure type and Range A: Current output
H: External input
Pressure Rated range
01 0.0 to 100.0 kPa ❻ Pressure port
Static
1 0 to 1,000 kPa Medium
Pneumatic Fluid
V01 Negative 0.0 to -101.3 kPa Port
C01 Compound -101.3 to 100.0 kPa R1/8 ○ ○
Rc1/8 ○ -
❸ Wiring NPT1/8 ○ ○
No mark: Cable type (fluid type) 7/16-20UNF - ○
C: Connector type 9/16-18UNF - ○

Product Components
• Product • Instruction manual • Unit sticker
• Connector type: Bracket A / B, Connector wiring (PSO-C01)
• Cable type: Bracket C

Specifications
PSAN- PSAN- PSAN-
Model PSAN-□1□□□-□
□V01C□□-□ □01C□□-□ □C01□□□-□
Pneumatic type model: Gauge pressure
Pressure Type
Fluid type model: Gauge pressure 01) or sealed gauge pressure 02)
Pressure Negative Static Compound

PSAN Series
Min display unit 0.1 kPa 0.1 kPa 1 kPa 0.1 kPa
Rated pressure 0.0 to -101.3 0.0 to 100.0 -101.3 to 100.0
0 to 1,000 kPa

CATALOG
range kPa kPa kPa
Display & setting 5.0 to -101.3 -5.0 to 110.0 -101.3 to 110.0
-101.3 to 1,100 kPa
pressure range kPa kPa kPa
Display type 7 Segment LED, 4 ½ digit
Display accuracy -10 to 0 ℃: ≤ ±1% F.S., 0 to 50 ℃: ≤ ±0.5% F.S.
For your safety, read and follow the considerations written in the instruction
• Pneumatic type:
manual, other manuals and Autonics website. Rated pressure Rated Rated pressure ×1.5 Rated pressure
Max. pressure
The specifications, dimensions, etc are subject to change without notice for product ×2 pressure ×2 • Fluid type: Rated ×2
pressure ×2
improvement Some models may be discontinued without notice.
01) Only for static pressure, rated pressure range 100.0 kPa model
02) The unit is sealed structure. It is based on atmospheric pressure 101.3 kPa.

Fluid type (non-corrosive gas and

Applicable Pneumatic type
Features medium (air, non-corrosive gas)
fluid that do not corrode stainless
steel 316L)
Connection type Connector type Cable type / connector type
• Pressure measurement of any gas, liquid or oil (except substances which may corrode
Connector type: Ø 4 mm, 5-core, 2 m
stainless steel 304/316L) Cable Ø 4 mm, 5-core, 2 m
Cable type: Ø 4 mm, 5-core, 3 m
• Auto shift function: with change in the original pressure, the external input adjusts the Wire spec. AWG24 (0.08 mm, 40-core), insulator diameter: Ø 1 mm
determined level to match the change in pressure (only available in models with auto Front case: PC
Front case: PC
shift/hold function) Material
Back case: (back port) PC / (bottom
Back case: PA6
port) PBT+GF15%
• Hold function: hold current display value or control output Pressure port: SUS304/SUS316L
Pressure port: Brass-nickel plated
• Forced output control mode for device testing and maintenance Protection
Connector type: IP40 (IEC standard)
Connector type: IP40 (IEC standard)
structure Cable type: IP65 (IEC standard)
• One-touch connector type for easy wiring and maintenance
Approval ᜢᜫ
• Zero-point adjustment function, peak value monitoring function, chattering Unit weight Back port: ≈ 80 g (≈ 165 g) Connector type: ≈ 88 g (≈ 173 g)
prevention function (packaged) Bottom port: ≈ 85 g (≈ 170 g) Cable type: ≈ 90 g (≈ 167 g)

ᜢᜫ
-|Transparent Guide|-

Power supply 12 - 24 VDCᜡ (ripple P-P: ≤ 10%)

Unit Descriptions
Allowable voltage
90 to 110% of rated voltage
range 1. Pressure range (sticker)
Current consumption ≤ 50 mA 01) 2. Display part (red)
Control output NPN open collector output / PNP open collector output model
1 Run mode: Displays PV (present value), SV (setting
Load voltage ≤ 30 VDCᜡ value)
2
Load current ≤ 100 mA Setting mode: Displays parameter and setting value
Residual voltage NPN: ≤ 1 VDCᜡ, PNP: ≤ 2 VDCᜡ 3. Output indicator (OUT1: red , OUT2: green)
Hysteresis According to output operation mode 02) 3 3 Turns ON when the corresponding control output is
ON.
Repeat error ±0.2% F.S. ±min display interval 4
Response time 2.5, 5, 100, 500, 1000 ms 4. [M] key
Protection circuit Output short over-current protection circuit Enters parameter group, selects item and returns
Insulation resistance ≥ 50 MΩ (500 VDCᜡ megger) 5 run mode.
5. [▼] , [▲] key
Dielectric strength 1,000 VACᜠ 50 / 60 Hz for 1 min
Sets preset of output operation mode, runs the
1.5 mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y,
Vibration mode or changes parameter.
Z direction for 2 hours
Ambient temperature -10 to 50 ℃, Storage: -20 to 60 ℃ (no freezing or condensation)

Sold Separately
Ambient humidity 30 to 80%RH, Storage: 30 to 80%RH (no freezing or condensation)
01) Current output: ≤ 75 mA
02) Refer to 'Output operation mode'. ±1digit error may occur due to pressure unit operation.
• Front cover (PSO-P01), Panel bracket (PSO-B02/B03)
Analog output Voltage (1 - 5 VDCᜡ ±2% F.S) Current (DC 4 - 20mA ±2% F.S) • Pneumatic type: M5 gender (PSO-Z01)
Output impedance 1 kΩ -
Linearity ≤ ±1% F.S ≤ ±1% F.S
Zero-point ≤ 1 VDCᜡ ±2% F.S. ≤ DC 4 mA ±2% F.S. Sold Separately: Protection cover / Panel brackets
Span ≤ 4 VDCᜡ ±2% F.S. ≤ DC 16 mA ±2% F.S. • Unit: mm, For the detailed drawings, follow the Autonics website.
Resolution 1/1000 or 1/2000 (different by pressure type and display unit)
Response time 50 ms 70 ms
■ Front cover (PSO-P01) ■P
 anel bracket
40 5.7 (PSO-B02/B03)
9.7 1

Dimensions

28.2
40

42
35
26
• Unit: mm, For the detailed drawings, follow the Autonics website.

40
42
■ Pneumatic type, back port, connector type 30
3
30.7 40
B 20
30 22.8 7.9 A 20 Port A B
25.8
2-M3
Rc1/8
0 - ■ Panel cut-out ■ Installation configuration
(standard) □36 +0.5
• Sold separately: Front cover (PSO-P01),
0

NPT1/8 0 Inner M5
20

12 tap
Panel bracket (PSO-B02/B03)
R1/8 8
• Panel thickness: 0.8 to 3.5 mm
■ Pneumatic type, bottom port, connector type
Front cover
(PSO-P01)
cable Panel bracket
30 32
20 2-M3 Panel Thickness: (PSO-B02)
0.8 to 3.5 mm
20
39

Rc1/8(standard), NPT1/8 Installation

panel
■ Fluid type, bottom port, connector type Pressure sensor

30 32 20 2-M3
■ M5 gender (PSO-Z01)
M5

Port A B
12

R1/8
20
30

R1/8 or
41.3

(standard) 8 Inner M5 NPT1/8

1.6
tap 8.1
NPT1/8
11.3

7/16-
17 11 -
20UNF
A

■ Fluid type, back port, cable type

42.3
30 30 12.3 A B 20 2-M3

Port A B
20
30

R1/8 Inner M5
8
17 (standard) tap
9/16-
15.4 -
Ø4, 3m 18UNF
5.1

■ Bracket A ■ Bracket B ■ Bracket C

30
4.2

4.2
22

20 3-Ø3.2
6

25 22
35 Ø4.2
3.5

Ø22 20 4-Ø3.2
30
20 3-Ø3.2
45
40
4.2

20
20

15

55

20 Ø4.2 1.6
40
45
40

30 13
1.6
20

36 15

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

www.autonics.com | +82-2-2048-1577 | [email protected]