Ductile and

Cast Iron
Flanged
Fittings
2”– 48”

Metalfit
 Ductile and Cast Iron Flanged Fittings

Flanged Joint Dimensions

ANSI/AWWA C110/A21.10

BC

OD

Size OD BC T Hole Dia. Bolt Size No. Bolts

2 6.00 4.75 0.62 0.75 5/8 x 2-1/4 4
2-1/2 7.00 5.50 0.69 0.75 5/8 x 2-1/2 4
3 7.50 6.00 0.75 0.75 5/8 x 2-1/2 4
4 9.00 7.50 0.94 0.75 5/8 x 3 8
5 10.00 8.50 0.94 0.88 3/4 x 3 8
6 11.00 9.50 1.00 0.88 3/4 x 3-1/2 8
8 13.50 11.75 1.12 0.88 3/4 x 3-1/2 8
10 16.00 14.25 1.19 1.00 7/8 x 4 12
12 19.00 17.00 1.25 1.00 7/8 x 4 12
14 21.00 18.75 1.38 1.12 1 x 4-1/2 12
16 23.50 21.25 1.44 1.12 1 x 4-1/2 16
18 25.00 22.75 1.56 1.25 1-1/8 x 5 16
20 27.50 25.00 1.69 1.25 1-1/8 x 5 20
24 32.00 29.50 1.88 1.37 1-1/4 x 5-1/2 20
30 38.75 36.00 2.12 1.37 1-1/4 x 6-1/2 28
36 46.00 42.75 2.38 1.62 1-1/2 x 7 32
42 53.00 49.50 2.62 1.62 1-1/2 x 7-1/2 36
48 59.50 56.00 2.75 1.62 1-1/2 x 8 44

BASE DIMENSIONS INSTALLATION NOTE
Drilling Templates are furnished in multiples
Size B.C. Hole Dia. No. Bolts of four. Standard flanged reducers, with a
3 3.88 0.62 4 different number of holes in each flange, will
4 4.75 0.75 4 have only two centerlines which are common
6 5.50 0.75 4 to the drilling templates of both flanges.
B.C.
8 7.50 0.75 4
10 7.50 0.75 4
12 9.50 0.88 4
14 9.50 0.88 4
16 9.50 0.88 4
18 11.75 0.88 4
20 11.75 0.88 4
24 11.75 0.88 4
30 14.25 1.00 4
36 17.00 1.00 4
42 21.25 1.12 4
48 22.75 1.25 4
ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

2 Metalfit
 ENGINEERING SUBMITTAL DATA
Metalfit manufactures Ductile Iron and Gray Cast Iron Flanged Fittings for both Waterworks and
Industrial applications and conforms fully to the required industry standards. Flanged Fittings
are manufactured in accordance with ANSI/AWWA C110/A21.10 and ANSI B16.1, Class 125.
Metalfit 2˝ through 12˝ Flanged Fittings are also listed by Underwriters Laboratories for fire
protection service. Additionally, Metalfit hydrostatically tests every fitting to ensure quality
casting integrity. These tests are performed at 1.5 times the rated working pressure.

Mechanical Properties Water Working Pressure

Cast Iron to ASTM A48 Gray Cast Iron
Minimum Tensile Strength 31,000 psi 2” - 12” CI Fittings rated 250 psi
14” - 42” CI Fittings rated 150 psi

Ductile Iron to ASTM A 536 Ductile Iron

Minimum Tensile Strength 70,000 psi All DI Fittings Rated 250 psi
Yield Strength 50,000 psi As noted in ANSI/AWWA C111/A21/11,
Elongation 5% ductile iron flanged joints in the 24” and
smaller sizes may be rated to 350 psi with
the use of “special” gaskets.

COATINGS & LININGS
Interior Linings

Flanged fittings are furnished cement lined and seal coated per ANSI/AWWA C104/A21.4.
Fittings are also available unlined for air service or with other special linings for particular
service conditions.

Exterior Coatings

Flanged fittings are furnished standard with a red epoxy primer or tar coated at the customer’s
discretion. Special primer coatings are also available for particular service conditions.

All standard coatings and linings are provided in full accordance with ANSI/NSF 61.

COMMITMENT TO QUALITY
Metalfit takes pride in producing the finest quality Flanged Fittings available in today’s
market. Our manufacturing standards and a strict adherence to the quality control procedures,
developed over many years, make certain that we abide by our commitment to be the best.

Metalfit 3
 Ductile and Cast Iron Flanged Fittings
A
A A
A

A
T R A T R
T R

Bends, 1/4 (90 Deg) Bends, 1/8 (45 Deg) Bends, 1/16 (22-1/2 Deg)

Size Wt. A R T Size Wt. A R T Size Wt. A R T

2 14 4.5 3.0 0.31 2 12 2.5 2.41 0.31 2 12 2.5 6.04 0.31
21/2 22 5.0 3.5 0.31 21/2 18 3.0 3.02 0.31 21/2 18 3.0 6.80 0.31
3 25 5.5 4.0 0.48 3 20 3.0 3.62 0.48 3 20 3.0 7.56 0.48
4 45 6.5 4.5 0.52 4 40 4.0 4.81 0.52 4 40 4.0 10.06 0.52
5 52 7.5 5.5 0.52 5 45 4.5 6.04 0.52 5 45 4.5 10.86 0.52
6 65 8.0 6.0 0.55 6 55 5.0 7.25 0.55 6 55 5.0 15.06 0.55
8 105 9.0 7.0 0.60 8 90 5.5 8.44 0.60 8 90 5.5 17.62 0.60
10 165 11.0 9.0 0.68 10 130 6.5 10.88 0.68 10 135 6.5 22.62 0.68
12 235 12.0 10.0 0.75 12 195 7.5 13.25 0.75 12 205 7.5 27.62 0.75
14 290 14.0 11.5 0.66 14 220 7.5 12.06 0.66 14 225 7.5 25.12 0.66
16 370 15.0 12.5 0.70 16 280 8.0 13.25 0.70 16 285 8.0 27.62 0.70
18 450 16.5 14.0 0.75 18 325 8.5 14.50 0.75 18 335 8.5 30.19 0.75
20 580 18.0 15.5 0.80 20 430 9.5 16.88 0.80 20 435 9.5 35.19 0.80
24 900 22.0 18.5 0.89 24 630 11.0 18.12 0.89 24 640 11.0 37.69 0.89
30 1430 25.0 21.5 1.03 30 1120 15.0 27.75 1.03 30 1135 15.0 57.81 1.03
36 2135 28.0 24.5 1.15 36 1755 18.0 35.00 1.15 36 1790 18.0 72.88 1.15
42 3055 31.0 27.5 1.28 42 2600 21.0 42.25 1.28 42 2665 21.0 88.00 1.28
48 4095 34.0 30.5 1.42 48 3580 24.0 49.5 1.42 48 3665 24.0 103.06 1.42

A A
R

U
S

T
T R

Bends, 1/32 (11-1/4 Deg) BASE Bends

Size Wt. A R T Weight

Base Base
2 12 2.5 12.69 0.31
Size Bend Only R S T U BC
3 20 3.0 15.25 0.48
4 40 4.0 20.31 0.52 3 35 10 4.88 5.00 0.56 0.50 3.88
5 45 4.5 22.85 0.52 4 55 10 5.50 6.00 0.62 0.50 4.75
6 55 5.0 30.50 0.55 6 85 20 7.00 7.00 0.69 0.62 5.50
8 90 5.5 35.50 0.60 8 145 40 8.38 9.00 0.94 0.88 7.50
10 135 6.5 45.69 0.68 10 210 45 9.75 9.00 0.94 0.88 7.50
12 205 7.5 55.81 0.75 12 300 65 11.25 11.00 1.00 1.00 9.50
14 225 7.5 50.75 0.66 14 360 70 12.50 11.00 1.00 1.00 9.50
16 285 8.0 55.81 0.70 16 445 75 13.75 11.00 1.00 1.00 9.50
18 335 8.5 60.94 0.75 18 565 115 15.00 13.50 1.12 1.12 11.75
20 435 9.5 71.06 0.80 20 700 120 16.00 13.50 1.12 1.12 11.75
24 645 11.0 76.12 0.89 24 1030 130 18.50 13.50 1.12 1.12 11.75
30 1150 15.0 116.75 1.03 30 1625 190 23.00 16.00 1.19 1.15 14.25
36 1805 18.0 147.25 1.15 36 2385 250 26.00 19.00 1.25 1.15 17.00
42 2680 21.0 177.69 1.28 42 3465 410 30.00 23.50 1.44 1.28 21.25
48 3695 24.0 208.12 1.42 48 4610 515 34.00 25.00 1.56 1.42 22.75

ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.
4 Metalfit
Ductile and Cast Iron Flanged Fittings

A
Reducing 90 Deg. Bends
T
Size Wt. A R T T1 Size Wt. A R T T1
/
21 2­x2 18 5.0 3.5 0.31 0.31 20x10 385 18.0 15.5 0.80 0.68
3x2 22 5.5 4.0 0.48 0.31 20x12 415 18.0 15.5 0.80 0.75
3x21/2 23 5.5 4.0 0.48 0.31 20x14 435 18.0 15.5 0.80 0.66
A 4x2 27 6.6 4.5 0.52 0.31 20x16 475 18.0 15.5 0.80 0.70
T 4x21/2 29 6.6 4.5 0.52 0.31 20x18 515 18.0 15.5 0.80 0.75
R
4x3 29 6.6 4.5 0.52 0.48 24x6 480 22.0 18.5 0.89 0.55
5x4 51 7.5 5.5 0.52 0.52 24x8 505 22.0 18.5 0.89 0.60
6x3 45 8.0 6.0 0.55 0.48 24x10 545 22.0 18.5 0.89 0.68
6x4 55 8.0 6.0 0.55 0.52 24x12 575 22.0 18.5 0.89 0.75
6x5 65 8.0 6.0 0.55 0.52 24x14 595 22.0 18.5 0.89 0.66
8x4 75 9.0 7.0 0.60 0.52 24x16 635 22.0 18.5 0.89 0.70
8x5 80 9.0 7.0 0.60 0.52 24x18 675 22.0 18.5 0.89 0.75
8x6 85 9.0 7.0 0.60 0.55 24x20 740 22.0 18.5 0.89 0.80
10x4 110 11.0 9.0 0.68 0.52 30x12 840 25.0 21.5 1.03 0.75
10x6 135 11.0 9.0 0.68 0.55 30x14 860 25.0 21.5 1.03 0.66
10x8 150 11.0 9.0 0.68 0.60 30x16 900 25.0 21.5 1.03 0.70
12x4 140 12.0 10.0 0.75 0.52 30x18 940 25.0 21.5 1.03 0.75
12x6 160 12.0 10.0 0.75 0.55 30x20 1005 25.0 21.5 1.03 0.80
12x8 180 12.0 10.0 0.75 0.60 30x24 1165 25.0 21.5 1.03 0.89
12x10 210 12.0 10.0 0.75 0.68 36x12 1195 28.0 24.5 1.15 0.75
14x6 144 14.0 11.5 0.66 0.55 36x14 1215 28.0 24.5 1.15 0.66
14x8 200 14.0 11.5 0.66 0.60 36x16 1255 28.0 24.5 1.15 0.70
14x10 240 14.0 11.5 0.66 0.68 36x18 1295 28.0 24.5 1.15 0.75
14x12 270 14.0 11.5 0.66 0.75 36x20 1360 28.0 24.5 1.15 0.80
16x6 220 15.0 12.5 0.70 0.55 36x24 1520 28.0 24.5 1.15 0.89
16x8 240 15.0 12.5 0.70 0.60 36x30 1785 28.0 24.5 1.15 1.03
16x10 280 15.0 12.5 0.70 0.68 42x14 1675 31.0 27.5 1.28 0.66
16x12 310 15.0 12.5 0.70 0.75 42x16 1715 31.0 27.5 1.28 0.70
16x14 330 15.0 12.5 0.70 0.66 42x18 1755 31.0 27.5 1.28 0.75
18x6 260 16.5 14.0 0.75 0.55 42x20 1820 31.0 27.5 1.28 0.80
18x8 280 16.5 14.0 0.75 0.60 42­x24 1980 31.0 27.5 1.28 0.89
18x10 320 16.5 14.0 0.75 0.68 42x30 2245 31.0 27.5 1.28 1.03
A 18x12 350 16.5 14.0 0.75 0.75 42x36 2600 31.0 27.5 1.28 1.15
18x14 370 16.5 14.0 0.75 0.66 48x24 3240 34.0 30.5 1.42 0.89
18x16 410 16.5 14.0 0.75 0.70 48x30 3600 34.0 30.5 1.42 1.03
20x6 320 18.0 15.5 0.80 0.55 48x36 3255 34.0 30.5 1.42 1.15
20x8 345 18.0 15.5 0.80 0.60 48x42 4685 34.0 30.5 1.42 1.28
T
A
T

Side Outlet Bends

B
Size Wt. A T
3 36 5.5 0.48
4 60 6.5 0.50
6 96 8.0 0.55 A
8 150 9.0 0.60
10 235 11.0 0.68 RETURN Bends
12 335 12.0 0.80
14 405 14.0 0.66 Size Wt. A B T
16 490 15.0 0.70
18 580 16.5 0.75 4 60 10 6.5 0.52
20 740 18.0 0.80 6 95 12 8.0 0.55
24 1145 22.0 0.89 8 165 18 9.0 0.60
10 260 20 11.0 0.68
12 395 24 12.0 0.75
ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

Metalfit 5
 Ductile and Cast Iron Flanged Fittings

A
T
R

U R
Long Radius Reducing
T
Bends
S
Size Wt. H J T T1
Long Radius Base Bends 4x3 32 9.0 0.52 0.48 7.0
6x4 61 11.5 0.55 0.52 9.5
Weight 8x4 100 14.0 0.60 0.52 12.0
Base Base 8x6 110 14.0 0.60 0.55 12.0
Size Bend Only R S T U BC 10x4 195 16.5 0.68 0.52 14.5
3 48 18 4.88 5.0 0.56 0.50 3.88 10x6 180 16.5 0.68 0.55 14.5
4 73 23 5.50 6.0 0.62 0.50 4.75 10x8 215 16.5 0.68 0.60 14.5
6 120 40 7.00 7.0 0.69 0.62 5.50 12x6 235 19.0 0.75 0.55 17.0
8 205 65 8.38 9.0 0.94 0.88 7.50 12x8 285 19.0 0.75 0.60 17.0
10 295 80 9.75 9.0 0.94 0.88 7.50 12x10 325 19.0 0.75 0.68 17.0
12 435 95 11.25 11.0 1.00 1.00 9.50 14x8 285 21.5 0.66 0.60 19.0
14 490 105 12.50 11.0 1.00 1.00 9.50 14x10 325 21.5 0.66 0.68 19.0
16 615 110 13.75 11.0 1.00 1.00 9.50 14x12 370 21.5 0.66 0.75 19.0
18 800 170 15.00 13.5 1.12 1.12 11.75 16x8 395 24.0 0.70 0.60 21.5
20 985 175 16.00 13.5 1.12 1.12 11.75 16x10 395 24.0 0.70 0.68 21.5
24 1430 190 18.50 13.5 1.12 1.12 11.75 16x12 415 24.0 0.70 0.75 21.5
30 2400 295 23.00 16.0 1.19 1.15 14.25 16x14 460 24.0 0.70 0.66 21.5
36 3680 395 26.00 19.0 1.25 1.15 17.00 18x10 465 26.5 0.75 0.68 24.0
18x12 585 26.5 0.96 0.75 24.0
18x14 535 26.5 0.75 0.66 24.0
18x16 585 26.5 0.75 0.70 24.0
B 20x10 640 29.0 0.80 0.68 26.5
20x12 630 29.0 0.80 0.75 26.5
20x14 770 29.0 0.80 0.66 26.5
20x16 695 29.0 0.80 0.70 26.5
20x18 905 29.0 0.80 0.75 26.5
24x12 855 34.0 0.89 0.75 30.5
24x14 875 34.0 0.89 0.66 30.5
B 24x16 940 34.0 0.89 0.70 30.5
T R 24x20 1080 34.0 0.89 0.80 30.5
30x16 1400 41.5 1.03 0.70 38.0
30x20 1575 41.5 1.03 0.80 38.0
LONG RADIUS BENDS 30x24 1675 41.5 1.37 1.16 38.0
36x20 2835 49.0 1.15 0.80 45.5
36x24 3140 49.0 1.15 0.89 45.5
Size Wt. B T R 36x30 3675 49.0 1.58 1.37 45.5
2 20 6.50 0.31 5.0 42x30 4905 56.5 1.28 1.03 53.0
21/2 22 7.00 0.31 6.0 42x36 4270 56.5 1.28 1.15 53.0
3 30 7.75 0.48 6.0
4 50 9.00 0.52 7.0
6 80 11.50 0.55 9.5
8 140 14.00 0.60 12.0
10 215 16.50 0.68 14.5
12 325 19.00 0.75 17.0
14 385 21.50 0.66 19.0
16 505 24.00 0.70 21.0
18 630 26.50 0.75 24.0
20 810 29.00 0.80 26.5
24 1240 34.00 0.89 30.5
30 2105 41.50 1.03 38.0 ANSI/AWWA C110/A21.10
36 3285 49.00 1.15 45.5
45 4865 56.50 1.28 53.0 Dimensions in inches.
Weights in pounds.

6 Metalfit
Ductile and Cast Iron Flanged Fittings

45º Lateral Wyes

Size Wt H J I T
3 45 10.0 3.0 10.0 0.48
4 75 12.0 3.0 12.0 0.52
6 120 14.5 3.5 14.5 0.55 H
8 200 17.5 4.5 17.5 0.60
10 335 20.5 5.0 20.5 0.80 T
12 515 24.5 5.5 24.5 0.87 I
14 605 27.0 6.0 27.0 0.66 J
16 805 30.0 6.5 30.0 0.70
18 980 32.0 7.0 32.0 0.75
20 1265 35.0 8.0 35.0 0.80
24 1905 40.5 9.0 40.5 0.89
30 3225 49.0 10.0 49.0 1.03
36 5740 60.0 19.5 60.0 1.15

45º Reducing Lateral Wyes

Size Wt. A B C T T1 Size Wt. A B C T T1
4x3 65 12.0 3.0 12.0 0.52 0.48 18x16 935 32.0 7.0 32.0 0.75 0.70
6x4 105 14.5 3.5 14.5 0.55 0.52 20x8 995 35.0 8.0 35.0 0.80 0.60
8x4 165 17.5 4.5 17.5 0.60 0.52 20x10 1025 35.0 8.0 35.0 0.80 0.68
8x6 175 17.5 4.5 17.5 0.60 0.55 20x12 1065 35.0 8.0 35.0 0.80 0.75
10x4 235 20.5 5.0 20.5 0.68 0.52 20x14 1110 35.0 8.0 35.0 0.80 0.66
10x6 250 20.5 5.0 20.5 0.68 0.55 20x16 1155 35.0 8.0 35.0 0.80 0.70
10x8 270 20.5 5.0 20.5 0.68 0.60 20x18 1315 35.0 8.0 35.0 0.80 0.75
12x4 350 24.5 5.5 24.5 0.75 0.52 24x8 1470 40.5 9.0 40.5 0.89 0.60
12x6 365 24.5 5.5 24.5 0.75 0.55 24x10 1505 40.5 9.0 40.5 0.89 0.68
12x8 390 24.5 5.5 24.5 0.75 0.60 24x12 1550 40.5 9.0 40.5 0.89 0.75
12x10 470 24.5 5.5 24.5 0.75 0.68 24x14 1590 40.5 9.0 40.5 0.89 0.66
14x6 475 27.0 6.0 27.0 0.66 0.55 24x16 1640 40.5 9.0 40.5 0.89 0.70
14x8 500 27.0 6.0 27.0 0.66 0.60 24x18 1685 40.5 9.0 40.5 0.89 0.75
14x10 525 27.0 6.0 27.0 0.66 0.68 24x20 1750 40.5 9.0 40.5 0.89 0.80
14x12 570 27.0 6.0 27.0 0.66 0.75 30x12 2795 49.0 10.0 49.0 1.03 0.75
16x6 620 30.0 6.5 30.0 0.70 0.55 30x14 2850 49.0 10.0 49.0 1.03 0.66
16x8 645 30.0 6.5 30.0 0.70 0.60 30x16 2905 49.0 10.0 49.0 1.03 0.70
16x10 675 30.0 6.5 30.0 0.70 0.68 30x18 2960 49.0 10.0 49.0 1.03 0.75
16x12 715 30.0 6.5 30.0 0.70 0.75 30x20 3040 49.0 10.0 49.0 1.03 0.80
16x14 755 30.0 6.5 30.0 0.70 0.66 30x24 3205 49.0 10.0 49.0 1.03 0.89
18x8 780 32.0 7.0 32.0 0.75 0.60 36x16 4455 54.0 15.3 54.0 1.15 0.70
18x10 810 32.0 7.0 32.0 0.75 0.68 36x18 4505 54.0 15.3 54.0 1.15 0.75
18x12 850 32.0 7.0 32.0 0.75 0.75 36x20 4575 54.0 15.3 54.0 1.15 0.80
18x14 885 32.0 7.0 32.0 0.75 0.66 36x24 4725 54.0 15.3 54.0 1.15 0.89

A
T1
T
C
B

ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

Metalfit 7
 Ductile and Cast Iron Flanged Fittings

TEES

Size Wt. H J T

2 20 4.5 4.5 0.31
21/2 27 5.0 5.0 0.31
3 40 5.5 5.5 0.48
4 65 6.5 6.5 0.52
5 85 7.5 7.5 0.52 H H
6 95 8.0 8.0 0.55
8 155 9.0 9.0 0.60
10 270 11.0 11.0 0.80 T
12 385 12.0 12.0 0.87
14 435 14.0 14.0 0.66
J
16 550 15.0 15.0 0.70
18 665 16.5 16.5 0.75
20 855 18.0 18.0 0.80
24 1330 22.0 22.0 0.89
30 2150 25.0 25.0 1.03
36 3160 28.0 28.0 1.15
42 5580 31.0 31.0 1.78
42 (150 psi) 4470 31.0 31.0 1.28

REDUCING TEES
Size Wt. H J T T1 Size Wt. H J T T1 Size Wt. H J T T1
3x2 35 5.5 5.5 0.48 0.31 16x12 520 15.0 15.0 0.70 0.75 36x12 2170 20.0 26.0 1.15 0.75
3x21/2 37 5.5 5.5 0.48 0.31 16x14 530 15.0 15.0 0.70 0.66 36x14 2175 20.0 26.0 1.15 0.66
4x2 50 6.5 6.5 0.52 0.31 18x6 480 13.0 15.5 0.75 0.55 36x16 2185 20.0 26.0 1.15 0.70
4x21/2 55 6.5 6.5 0.52 0.31 18x8 495 13.0 15.5 0.75 0.60 36x18 2190 20.0 26.0 1.15 0.75
4x3 60 6.5 6.5 0.52 0.48 18x10 510 13.0 15.5 0.75 0.68 36x20 2210 20.0 26.0 1.15 0.80
5x4 80 7.5 7.5 0.52 0.52 18x12 535 13.0 15.5 0.75 0.75 36x24 2255 20.0 26.0 1.15 0.89
6x2 85 8.0 8.0 0.55 0.31 18x14 630 16.5 16.5 0.75 0.66 36x30 3000 28.0 28.0 1.15 1.03
6x21/2 85 8.0 8.0 0.55 0.31 18x16 650 16.5 16.5 0.75 0.70 42x12 3165 23.0 30.0 1.28 0.75
6x3 85 8.0 8.0 0.55 0.48 20x6 610 14.0 17.0 0.80 0.55 42x14 3170 23.0 30.0 1.28 0.66
6x4 90 8.0 8.0 0.55 0.52 20x8 620 14.0 17.0 0.80 0.60 42x16 3180 23.0 30.0 1.28 0.70
6x5 95 8.0 8.0 0.55 0.52 20x10 635 14.0 17.0 0.80 0.68 42x18 3185 23.0 30.0 1.28 0.75
8x3 135 9.0 9.0 0.60 0.48 20x12 660 14.0 17.0 0.80 0.75 42x20 3205 23.0 30.0 1.28 0.80
8x4 140 9.0 9.0 0.60 0.52 20x14 665 14.0 17.0 0.80 0.66 42x24 3245 23.0 30.0 1.28 0.89
8x6 145 9.0 9.0 0.60 0.55 20x16 810 18.0 18.0 0.80 0.70 42x30 4125 31.0 31.0 1.28 1.03
10x3 200 11.0 11.0 0.68 0.48 20x18 820 18.0 18.0 0.80 0.75 42x36 5360 31.0 31.0 1.78 1.58
10x4 205 11.0 11.0 0.68 0.52 24x6 845 15.0 19.0 0.89 0.55 48x12 4315 26.0 34.0 1.42 0.75
10x6 215 11.0 11.0 0.68 0.55 24x8 860 15.0 19.0 0.89 0.60 48x14 4315 26.0 34.0 1.42 0.66
10x8 225 11.0 11.0 0.68 0.60 24x10 880 15.0 19.0 0.89 0.68 48x16 4330 26.0 34.0 1.42 0.70
12x3 280 12.0 12.0 0.75 0.48 24x12 890 15.0 19.0 0.89 0.75 48x18 4330 26.0 34.0 1.42 0.75
12x4 290 12.0 12.0 0.75 0.52 24x14 900 15.0 19.0 0.89 0.66 48x20 4350 26.0 34.0 1.42 0.80
12x6 295 12.0 12.0 0.75 0.55 24x16 915 15.0 19.0 0.89 0.70 48x24 4385 26.0 34.0 1.42 0.89
12x8 310 12.0 12.0 0.75 0.60 24x18 1220 22.0 22.0 0.89 0.75 48x30 4455 26.0 34.0 1.42 1.03
12x10 360 12.0 12.0 0.87 0.80 24x20 1255 22.0 22.0 0.89 0.80
14x4 365 14.0 14.0 0.66 0.52 30x6 1460 18.0 23.0 1.03 0.55
H H
14x6 375 14.0 14.0 0.66 0.55 30x8 1470 18.0 23.0 1.03 0.60
14x8 390 14.0 14.0 0.66 0.60 30x10 1480 18.0 23.0 1.03 0.68
14x10 400 14.0 14.0 0.66 0.68 30x12 1490 18.0 23.0 1.03 0.75
14x12 425 14.0 14.0 0.66 0.75 30x14 1490 18.0 23.0 1.03 0.66 T1
16x4 440 15.0 15.0 0.70 0.52 30x16 1505 18.0 23.0 1.03 0.70 J
16x6 465 15.0 15.0 0.70 0.55 30x18 1515 18.0 23.0 1.03 0.75
16x8 475 15.0 15.0 0.70 0.60 30x20 1540 18.0 23.0 1.03 0.80
16x10 495 15.0 15.0 0.70 0.68 30x24 2025 25.0 25.0 1.03 0.89

ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

8 Metalfit
 Ductile and Cast Iron Flanged Fittings

H H

T
J

R
U

S T T

Base Tees Reducing Tees ON RUN

Weight Size Wt. H J T T1
Base Base 4x2x4 50 6.5 6.5 0.52 0.48
Size Tee Only R S T U BC 4x3x3 53 6.5 6.5 0.52 0.48
3 45 5 4.88 5.00 0.56 0.50 3.88 4x3x4 55 6.5 6.5 0.52 0.52
4 75 10 5.50 6.00 0.62 0.50 4.75 6x3x4 85 8.0 8.0 0.55 0.52
6 110 15 7.00 7.00 0.69 0.62 5.50 6x3x6 91 8.0 8.0 0.55 0.55
8 185 30 8.38 9.00 0.94 0.88 7.50 6x4x3 86 8.0 8.0 0.55 0.48
10 300 30 9.75 9.00 0.94 0.88 7.50 6x4x4 90 8.0 8.0 0.55 0.52
12 430 45 11.25 11.00 1.00 1.00 9.50 6x4x6 95 8.0 8.0 0.55 0.52
14 485 50 12.50 11.00 1.00 1.00 9.50 8x4x6 140 9.0 9.0 0.60 0.55
16 600 50 13.75 11.00 1.00 1.00 9.50 8x4x8 135 9.0 9.0 0.60 0.60
18 740 75 15.00 13.50 1.12 1.12 11.75 8x6x4 125 9.0 9.0 0.60 0.55
20 930 75 16.00 13.50 1.12 1.12 11.75 8x6x6 145 9.0 9.0 0.60 0.55
24 1410 80 18.50 13.50 1.12 1.12 11.75 8x6x8 160 9.0 9.0 0.60 0.55
30 2270 120 23.00 16.00 1.19 1.15 14.25 10x6x10 234 11.0 11.0 0.80 0.80
36 3320 160 26.00 19.00 1.25 1.15 17.00 10x8x6 210 11.0 11.0 0.80 0.55
42 5850 270 30.00 23.50 1.44 1.28 21.25 10x8x8 227 11.0 11.0 0.80 0.60
10x8x10 248 11.0 11.0 0.80 0.80
12x6x12 300 12.0 12.0 0.87 0.80
12x8x8 275 12.0 12.0 0.87 0.80
12x8x12 310 12.0 12.0 0.75 0.60
Bullhead Tees 12x10x10 325 12.0 12.0 0.87 0.80
H H
12x10x12 350 12.0 12.0 0.87 0.87
Size Wt. H J T1 T 14x10x10 380 14.0 14.0 0.66 0.68
T 14x10x12 400 14.0 14.0 0.66 0.68
J 2 / x2 / x3
12 12 36 5.5 5.5 0.31 0.48 14x10x14 425 14.0 14.0 0.66 0.68
3x3x4 49 6.5 6.5 0.48 0.52 16x10x10 490 15.0 15.0 0.70 0.68
4x4x6 88 8.0 8.0 0.52 0.55 16x12x12 525 14.0 14.0 0.70 0.66
6x6x8 142 9.0 9.0 0.55 0.60 16x12x16 600 15.0 15.0 0.70 0.75
8x8x10 240 11.0 11.0 0.60 0.68 16x14x16 630 14.0 14.0 0.70 0.66
T
10x10x12 340 12.0 12.0 0.80 0.87 20x12x20 660 18.0 18.0 0.80 0.75
12x12x16 425 15.0 15.0 0.75 0.75 20x14x20 680 18.0 18.0 0.80 0.66
12x12x24 845 22.0 22.0 0.75 0.89 24x16x24 915 22.0 22.0 0.89 0.70
16x16x24 993 22.0 22.0 0.70 0.89 36x24x36 2255 28.0 28.0 1.15 0.89

H H SIDE OUTLET Tees

Size Wt. H J T1 T
T1

J 4 82 6.5 6.5 0.52 0.52

6 135 8.0 8.0 0.55 0.55
8 210 9.0 9.0 0.60 0.60
10 330 11.0 11.0 0.68 0.80
12 470 12.0 12.0 0.75 0.87
T 14 650 14.0 14.0 0.66 0.66
16 850 15.0 15.0 0.70 0.70
18 1040 16.5 16.5 0.75 0.75
20 1330 18.0 18.0 0.80 0.80
24 2080 22.0 22.0 0.89 0.89
ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

Metalfit 9
 Ductile and Cast Iron Flanged Fittings

L
T
T1

Concentric Reducers
Size Wt. L T T1 Size Wt. L T T1
2 / x2
12 14 5.5 0.31 0.31 16x12 265 18.0 0.70 0.75
3x2 16 6.0 0.48 0.31 16x14 280 18.0 0.70 0.66
3x21/2 20 6.0 0.48 0.31 18x6 230 19.0 0.75 0.55
4x2 25 7.0 0.52 0.31 18x8 240 19.0 0.75 0.60
4x21/2 28 7.0 0.52 0.31 18x10 265 19.0 0.75 0.68
4x3 30 7.0 0.52 0.48 18x12 295 19.0 0.75 0.75
5x3 38 8.0 0.52 0.48 18x14 310 19.0 0.75 0.66
5x4 40 8.0 0.52 0.52 18x16 340 19.0 0.75 0.70
6x2 35 9.0 0.55 0.31 20x6 300 20.0 0.80 0.55
6x21/2 38 9.0 0.55 0.31 20x8 305 20.0 0.80 0.60
6x3 40 9.0 0.55 0.48 20x10 310 20.0 0.80 0.68
6x4 45 9.0 0.55 0.52 20x12 345 20.0 0.80 0.75
6x5 50 9.0 0.55 0.52 20x14 355 20.0 0.80 0.66
8x3 60 11.0 0.60 0.48 20x16 390 20.0 0.80 0.70
8x4 65 11.0 0.60 0.52 20x18 410 20.0 0.80 0.75
8x5 70 11.0 0.60 0.52 24x8 460 24.0 0.89 0.60
8x6 75 11.0 0.60 0.55 24x10 470 24.0 0.89 0.68
10x4 85 12.0 0.68 0.52 24x12 480 24.0 0.89 0.75
10x5 88 12.0 0.68 0.52 24x14 490 24.0 0.89 0.66
10x6 90 12.0 0.68 0.55 24x16 525 24.0 0.89 0.70
10x8 110 12.0 0.68 0.60 24x18 550 24.0 0.89 0.75
12x4 120 14.0 0.75 0.52 24x20 590 24.0 0.89 0.80
12x6 130 14.0 0.75 0.55 30x18 810 30.0 1.03 0.75
12x8 145 14.0 0.75 0.60 30x20 870 30.0 1.03 0.80
12x10 170 14.0 0.75 0.68 30x24 970 30.0 1.03 0.89
14x4 150 16.0 0.66 0.52 36x20 1230 36.0 1.15 0.80
14x6 155 16.0 0.66 0.55 36x24 1345 36.0 1.15 0.89
14x8 175 16.0 0.66 0.60 36x30 1555 36.0 1.15 1.03
14x10 190 16.0 0.66 0.68 42x24 1820 42.0 1.28 0.89
14x12 220 16.0 0.66 0.75 42x30 2060 42.0 1.28 1.03
16x4 180 18.0 0.70 0.52 42x36 2345 42.0 1.28 1.15
16x6 190 18.0 0.70 0.55 48x30 2625 48.0 1.42 1.03
16x8 210 18.0 0.70 0.60 48x36 2950 48.0 1.42 1.15
16x10 235 18.0 0.70 0.68 48x42 3320 48.0 1.42 1.28

ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

10 Metalfit
Ductile and Cast Iron Flanged Fittings

Reducing Crosses
Size Wt. H J T T1 Size Wt. H J T T1
3x2 45 5.5 5.5 0.48 0.31 42x24 3395 23.0 30.0 1.28 0.89
4x2 60 6.5 6.5 0.52 0.31 42x30 4375 31.0 31.0 1.28 1.03
4x21/2 65 6.5 6.5 0.52 0.31 42x36 5720 31.0 31.0 1.78 1.58
4x3 70 6.5 6.5 0.52 0.48 48x10 4350 34.0 26.0 1.42 0.68
6x2 90 8.0 8.0 0.55 0.31 48x12 4390 34.0 26.0 1.42 0.75
6x3 95 8.0 8.0 0.55 0.48 48x14 4385 34.0 26.0 1.42 0.66
6x4 110 8.0 8.0 0.55 0.52 48x16 4415 34.0 26.0 1.42 0.70
8x4 155 9.0 9.0 0.60 0.52 48x18 4420 34.0 26.0 1.42 0.75
8x6 165 9.0 9.0 0.60 0.55 48x20 4460 34.0 26.0 1.42 0.80
10x4 220 11.0 11.0 0.68 0.52 48x24 4535 34.0 26.0 1.42 0.89
10x6 240 11.0 11.0 0.68 0.55 48x30 4670 34.0 26.0 1.42 1.03
10x8 265 11.0 11.0 0.68 0.60
12x4 310 12.0 12.0 0.75 0.52
12x6 320 12.0 12.0 0.75 0.55 H H
12x8 345 12.0 12.0 0.75 0.60
12x10 415 12.0 12.0 0.87 0.80
14x6 400 14.0 14.0 0.66 0.55 T1
J
14x8 425 14.0 14.0 0.66 0.60
14x10 460 14.0 14.0 0.66 0.68
14x12 505 14.0 14.0 0.66 0.75
16x6 490 15.0 15.0 0.70 0.55
16x8 520 15.0 15.0 0.70 0.60 J
16x10 555 15.0 15.0 0.70 0.68 T
16x12 605 15.0 15.0 0.70 0.75
16x14 620 15.0 15.0 0.70 0.66
18x6 505 13.0 15.5 0.75 0.55 H H
18x8 535 13.0 15.5 0.75 0.60
18x10 560 13.0 15.5 0.75 0.68
18x12 610 13.0 15.5 0.75 0.75 T
18x14 720 16.5 16.5 0.75 0.66 J
18x16 765 16.5 16.5 0.75 0.70
20x6 635 14.0 17.0 0.80 0.55
20x8 665 14.0 17.0 0.80 0.60
20x10 685 14.0 17.0 0.80 0.68
20x12 735 14.0 17.0 0.80 0.75 J
20x14 745 14.0 17.0 0.80 0.66
20x16 915 18.0 18.0 0.80 0.70
20x18 945 18.0 18.0 0.80 0.75
24x6 875 15.0 19.0 0.89 0.55 Crosses
24x8 895 15.0 19.0 0.89 0.60
24x10 930 15.0 19.0 0.89 0.68 Size Wt. H J T
24x12 960 15.0 19.0 0.89 0.75 2 30 4.5 4.5 0.31
24x14 975 15.0 19.0 0.89 0.66 21/2 41 5.0 5.0 0.31
24x16 1010 15.0 19.0 0.89 0.70 3 50 5.5 5.5 0.48
24x18 1365 22.0 22.0 0.89 0.75 4 80 6.5 6.5 0.52
24x20 1430 22.0 22.0 0.89 0.80 6 120 8.0 8.0 0.55
30x12 1565 18.0 23.0 1.03 0.75 8 195 9.0 9.0 0.60
30x14 1570 18.0 23.0 1.03 0.66 10 330 11.0 11.0 0.80
30x16 1605 18.0 23.0 1.03 0.70 12 460 12.0 12.0 0.87
30x18 1615 18.0 23.0 1.03 0.75 14 530 14.0 14.0 0.66
30x20 1670 18.0 23.0 1.03 0.80 16 665 15.0 15.0 0.70
30x24 2245 25.0 25.0 1.03 0.89 18 795 16.5 16.5 0.75
36x12 2240 20.0 26.0 1.15 0.75 20 1015 18.0 18.0 0.80
36x14 2240 20.0 26.0 1.15 0.66 24 1570 22.0 22.0 0.89
36x16 2270 20.0 26.0 1.15 0.70 30 2500 25.0 25.0 1.03
36x18 2280 20.0 26.0 1.15 0.75 36 3620 28.0 28.0 1.15
36x20 2325 20.0 26.0 1.15 0.80 42 (150 psi) 5060 31.0 31.0 1.28
36x24 2405 20.0 26.0 1.15 0.89
36x30 3300 28.0 28.0 1.15 1.03 ANSI/AWWA C110/A21.10
42x12 3240 23.0 30.0 1.28 0.75
42x16 3270 23.0 30.0 1.28 0.70 Dimensions in inches.
42x18 3275 23.0 30.0 1.28 0.75
Weights in pounds.
42x20 3320 23.0 30.0 1.28 0.80

 Metalfit 11
 Ductile and Cast Iron Flanged Fittings

Eccentric Reducers L

Size Wt. L T T1 Size Wt. L T T1 T

3x2 16 6 0.48 0.31 18x8 240 19 0.75 0.60 T1
3x21/2 20 6 0.48 0.31 18x10 265 19 0.75 0.68
4x2 26 7 0.52 0.31 18x12 295 19 0.75 0.75
4x21/2 28 7 0.52 0.31 18x14 310 19 0.75 0.66
4x3 30 7 0.52 0.48 18x16 340 19 0.75 0.70
6x2 35 9 0.55 0.31 20x10 310 20 0.80 0.68
6x21/2 38 9 0.55 0.31 20x12 345 20 0.80 0.75
6x3 40 9 0.55 0.48 20x14 355 20 0.80 0.66
6x4 45 9 0.55 0.52 20x16 390 20 0.80 0.70
6x5 50 9 0.55 0.52 20x18 410 20 0.80 0.75
8x4 65 11 0.60 0.52 24x12 480 24 0.89 0.75
8x5 70 11 0.60 0.52 24x14 490 24 0.89 0.66
8x6 75 11 0.60 0.55 24x16 525 24 0.89 0.70
10x4 85 12 0.68 0.52 24x18 550 24 0.89 0.75
10x6 90 12 0.68 0.55 24x20 590 24 0.89 0.80
10x8 110 12 0.68 0.60 30x18 810 30 1.03 0.75
12x4 120 14 0.75 0.52 30x20 870 30 1.03 0.80
12x6 130 14 0.75 0.55 30x24 970 30 1.03 0.89
12x8 145 14 0.75 0.60 36x18 1200 36 1.15 0.75
12x10 170 14 0.75 0.68 36x20 1230 36 1.15 0.80
14x6 155 16 0.66 0.55 36x24 1345 36 1.15 0.89
14x8 175 16 0.66 0.60 36x30 1555 36 1.15 1.03
14x10 190 16 0.66 0.68 42x24 1820 42 1.28 0.89
14x12 220 16 0.66 0.75 42x30 2060 42 1.28 1.03
16x6 190 18 0.70 0.55 42x36 2345 42 1.28 1.15
16x8 210 18 0.70 0.60 48x30 2625 48 1.42 1.03
16x10 235 18 0.70 0.68 48x36 2950 48 1.42 1.15
16x12 265 18 0.70 0.75 48x42 3320 48 1.42 1.28
16x14 280 18 0.70 0.86

R A
T

C
C C

L C

Straight Flare Pieces 90º Flare Bends

Size Wt. T C L R Size Wt T C A B
3 20 0.40 7.50 8 6 3 25 0.40 7.5 5.5 11
4 30 0.40 9.00 8 6 4 40 0.40 9.00 6.5 12
6 40 0.45 11.00 8 6 6 70 0.45 11.00 8.0 12
8 70 0.53 13.50 10 8 8 110 0.53 13.50 9.0 14
10 95 0.55 16.00 10 10 10 175 0.55 16.00 11.0 17
12 155 0.60 19.00 12 12 12 245 0.60 19.00 12.0 18
14 165 0.65 21.00 12 14 14 340 0.65 21.00 14.0 20
16 240 0.70 23.50 16 16 16 460 0.70 23.50 15.0 21
18 275 0.75 25.00 16 18 18 560 0.75 25.00 16.5 22.5
20 355 0.80 27.50 18 20 20 700 0.80 27.50 18.0 24
24 480 0.90 32.00 18 24 24 1100 0.90 32.00 22.0 28
30 1100 1.07 38.75 24 30 30 1840 1.07 38.75 25.0 32
36 1460 1.19 46.00 24 36 36 2700 1.19 46.00 28.0 35
42 1900 1.28 53.00 30 42 42 3250 1.28 53.00 31.0 38
48 2375 1.42 59.50 18 48 48 4425 1.42 59.50 34.0 41
ANSI/AWWA C110/A21.10

Dimensions in inches.
Weights in pounds.

12 Metalfit
Ductile and Cast Iron Flanged Fittings

V Q
A A O

90º
T1
V
T Q
E O
12” and Larger

TRUE Wyes Blind Flanges*

Size Wt. T T1 A E
Size Wt. O Q V
4 55 0.52 0.52 6.5 3.0
6 85 0.55 0.55 8.0 3.5 3 9 7.50 0.75 0.69
8 140 0.60 0.60 9.0 4.5 4 16 9.00 0.94 0.88
10 205 0.68 0.68 11.0 5.0 6 25 11.00 1.00 0.94
12 300 0.75 0.75 12.0 5.5 8 42 13.50 1.12 1.06
14 435 0.66 0.66 14.0 6.0 10 63 16.00 1.19 1.12
12 85 19.00 1.25 0.81
14 120 21.00 1.38 0.88
16 145 23.50 1.44 1.00
18 185 25.00 1.56 1.06
20 245 27.50 1.69 1.12
24 370 32.00 1.88 1.25
30 500 38.75 2.12 1.44
36 790 46.00 2.38 1.62
42 1175 53.00 2.62 1.81
* Blind Flanges can be provided tapped according to
customer’s requirement.
V Q
O

10” and Smaller

FLAT Blind Flanges Blind Flanges W/2” TAP

V
Size Wt. O
O QQ V Size Wt O Q V
12 85 19.0 1.25 1.25 3 9 7.50 0.75 0.69
14 120 21.0 1.38 1.38 4 16 9.00 0.94 0.88
16 155 23.5 1.44 1.44 6 25 11.00 1.00 0.94
18 190 25.0 1.56 1.56 8 42 13.50 1.12 1.06
20 250 27.5 1.69 1.69 10 63 16.00 1.19 1.12
24 380 32.0 1.88 1.88 12 85 19.00 1.25 0.81
14 120 21.00 1.38 0.88
16 145 23.50 1.44 1.00
18 185 25.00 1.56 1.06
20 245 27.50 1.69 1.12
24 370 32.00 1.88 1.25
30 500 38.75 2.12 1.44
36 790 46.00 2.38 1.62
42 1175 53.00 2.62 1.81

Metalfit 13
 TAPS AND BOSSES
Flanged Fittings may be drilled and tapped if the fitting wall thickness will provide the effective
thread length as shown in the following table.

DRAIN TAPPINGS

Tap Size 3/8” 1/2” 3/4” 1” 1-1/4” 1-1/2” 2”

Length of
Thread “A” 0.41” 0.53” 0.55” 0.68” 0.71” 0.72” 0.76”

These lengths are in accordance with the effective thread length as required in ANSI B2.1. If the
tap size is too large to be accommodated by the standard fitting wall thickness, an integrally
cast boss may be required to provide the necessary thickness for tapping.

The following will serve as a guideline for maximum tap sizes into standard fitting wall thick-
nesses for ANSI/AWWA C110/A21.10 Flanged Fittings:

Fitting Maximum Tap

Size Size Without Boss

3” 1/2”
4”-6” 3/4”
8” 1-1/4”
10”-16” 1-1/2”
18”-42” 2”

To accommodate larger size holes that are impractical to thread,

it may be necessary to integrally cast a flanged boss to the fitting.
In this case, a boss the size of a flange shall be integrally cast. The
hole shall be cored or drilled at our option. The flange boss shall
be faced and the bolt holes drilled and blind tapped so as not to
interfere with the fitting wall thickness.

14 Metalfit
Ductile and Cast Iron Flanged Fittings

Methods of Designating Location

of Tapped Holes for Drains When Specified

Metalfit 15
Metalfit
5583 Snowflake Way
Parker, CO 80134

Phone: 303-840-2183
Fax: 303-840-2193
[email protected]