Scribd
Upload
85 views18 pages

Kaban Jahe

The quality self-check report summarizes test results from the Indosat DWDM project. Key tests included inventory checking, mean launched optical power levels, power supply voltages, and alarm functions. Test results showed installed equipment matched procurement documents. Optical power levels and voltages met specifications. Alarm indicators and sounds functioned properly. The report found the DWDM network installation and commissioning met technical requirements.

Uploaded by

dzulfatuh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views18 pages

Kaban Jahe

The quality self-check report summarizes test results from the Indosat DWDM project. Key tests included inventory checking, mean launched optical power levels, power supply voltages, and alarm functions. Test results showed installed equipment matched procurement documents. Optical power levels and voltages met specifications. Alarm indicators and sounds functioned properly. The report found the DWDM network installation and commissioning met technical requirements.

Uploaded by

dzulfatuh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

Indosat DWDM Project ZXONE 8000

Optical Transmission System

Single site Operation & Record Test Procedures

Site Name : Kaban Jahe

Site ID : 05KBJ002

Customer : PT. Indosat

Provider : PT. ZTE Indonesia

a
Contents

T01 Inventory Checking.........................................................................................................................................1


T01-01 :Inventory Checking............................................................................................................................1
T02 OTU: Mean Launched Optical Power ............................................................................................................3
T02-01 Mean Launched Optical Power ...........................................................................................................3
Specifications of the TST4 (Optical Transponder Unit)...................................................................................5
Specifications of the L4L×1 (OTN Line Board)..............................................................................................7
Specifications of the L4L×2 (OTN Line Board)..............................................................................................7
Specifications of the C2K×12 (OTN Tributary Board)....................................................................................9
T03System Function: Power Supply Voltage and Audible&Visual Alarm .......................................................... 10
T3-01Power Supply Voltage and Audible&Visual Alarm.............................................................................. 10

b
T01 Inventory Checking
T01-01 :Inventory Checking
Objective To verify that the actual board already installed on site compare with BOQ
Test Networking None
Diagram

Preset Conditions 1. The actual board must be same with BOQ.


2. If there is difference, please write on remarks column.
Test Procedures 1. Checked all material according to the BOQ
2. Check visual installation for the rack
3. Check cable installation and labeling
4. Check the cleanliness of the environment after installation
5. Record the result in the data sheet

Expected Results Installed board same with BOQ.


Test Description Test instrument: none
Requiring on-site operation: none
Estimated man-hour: 10 min
Risk: low

1
T02 OTU: Mean Launched Optical Power
T02-01 Mean Launched Optical Power
Objective To verify that the mean launched optical power on the WDM side and client side of
the OTU meets the optical power requirements of the engineering design.
Test Networking None
Diagram

Preset Conditions 1. The network must be working normally.


2. Lasers on the OTU must be enabled.
Test Procedures 1. Query the optical power at the output port Tx of the OTU by using the U31. The
displayed value is the mean launched optical power on the client side of the OTU.
2. Query the optical power at the output port OUT of the OTU by using the U31.
The displayed value is the mean launched optical power on the WDM side of the
OTU.
Expected Results The mean launched optical power meets the optical power requirements of the
engineering design refer to Technical Specification.
Test Description Test instrument: none
Requiring on-site operation: none
Estimated man-hour: 60 minutes
Risk: low

Technical Specifications
Test NO Test content Expected result Remarks
T02-01 T02-01 Mean Launched Optical Power

TST4 line side -5～0dBm

-4.3～4.5(4*25G)
TST4 Client side -5.8～
3.5dBm(10*10G)

L4L×1 line side -5～0dBm

L4L×2 line side -3～2dBm

C2K×12 Client side(I64.1) -6～-1dBm

3
Technical Specifications Tributary Board and Line Unit ZXONE 8000
Specifications of the TST4 (Optical Transponder Unit)
Specifications of optical module at the line side

Specifications of optical module at the Client side

5
6
Specifications of the L4L×1 (OTN Line Board)
Specifications of optical module at the line side

Specifications of the L4L×2 (OTN Line Board)


Specifications of optical module at the line side

Specifications of the L4L×2 (OTN Line Board)


Specifications of optical module at the line side

7
Specifications of the L4L×2 (OTN Line Board)
Specifications of optical module at the line side

8
Specifications of the C2K×12 (OTN Tributary Board)
Specifications of optical module at the Client side

9
T03 System Function: Power Supply Voltage and
Audible&Visual Alarm
T3-01Power Supply Voltage and Audible&Visual Alarm
Objective To verify that the power supply voltage and the audible and visual alarm function
of the NE and rack are normal.
Test Networking
Diagram

Preset Conditions The network commissioning must be complete and the power cables must be
connected properly.
Test Procedures 1. Use a power meter to measure the input power supply of the power supply board in
the sub-rack.
2. Simulate the alarm in NE; observe the alarm indicators (LED) on the cabinet.
3. Simulate the alarm in NE, check the audible alarm in the NE;
Expected Results 1. The measure power supply voltage is -40V~-57V.
2. The simulation of each scenario is successful. Details are as follows:
 Only the green indicator should be always on when the equipment has no
alarms.
 The green and yellow indicators on top of the cabinet should be always on
when the equipment has a minor alarm.
 The green, yellow and red indicators on top of the cabinet should be always on
when the equipment has a critical alarm.
3. The alarm sound can be cleared by pressing a button.
Test Description Test instrument: multimeter
Requiring on-site operation: yes
Estimated man-hour: 30 minutes
Risk: low

10
Doccument No.
DWDM16-EM-BN-QA- 20170222
Version No. V1.0

Quality Selfcheck Report

Indosat DWDM Project


Project Name Indosat DWDM Project

Document Title: Quality Selfcheck Report


Manager Responsible: Fan Guojian Authorised by: Liu Jinchun
Doc No. DWDM16-EM-BN-QA- Version No. Released
20170222 V1.0 Date 20161102

Version Date No. of pages Author Approver Details of Revision Changes


V1.0 22/02/2017 Fan Guojian Liu Jinchun First Edition

Distribution – ZTE, Indosat Confidential to ZTE and Indosat P1 of 1

You might also like