Scribd
Upload
138 views

Exp 7-Clipper Clamper

The document describes an experiment to build clipper and clamper circuits using a breadboard and Tinkercad. Clipper circuits clip off a portion of an alternating input signal without distorting the remaining part. Clamper circuits clamp a signal to different DC levels by using a capacitor, diode, and resistor along with an independent DC supply. The experiment involves building positive, negative, and dual clipper circuits as well as clamper circuits on a breadboard and observing the input and output waveforms on an oscilloscope as the circuits modify the signal. Precautions are outlined for safely performing the experiment.

Uploaded by

Nidhish Milind Sonavale
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
138 views

Exp 7-Clipper Clamper

The document describes an experiment to build clipper and clamper circuits using a breadboard and Tinkercad. Clipper circuits clip off a portion of an alternating input signal without distorting the remaining part. Clamper circuits clamp a signal to different DC levels by using a capacitor, diode, and resistor along with an independent DC supply. The experiment involves building positive, negative, and dual clipper circuits as well as clamper circuits on a breadboard and observing the input and output waveforms on an oscilloscope as the circuits modify the signal. Precautions are outlined for safely performing the experiment.

Uploaded by

Nidhish Milind Sonavale
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

EXPERIMENT - 7

AIM: To assemble variety of clipper and clamper circuits on the breadboard using
tinkercad

THEORY:

Clipper and clamping circuits are applications of diode as a switching device.


Input to these circuits must be of alternating nature with different shapes like sinusoidal,
square, triangular etc. Clippers circuit clips off a particular portion of the input signal
without distorting the remaining part of the input waveform. It increases the average
value of the input signal by clipping (removing) a particular portion of the wave. Often
DC source is also used to change the average level. A clipping circuit requires at least
two fundamental components, a diode and a resistor. A dc battery, however, is also used
in biased clippers. The output waveform can be clipped at different levels simply by
interchanging the position of the various elements and changing the magnitude of the dc
battery. Generally, ideal diodes are considered and the complete analysis can be based on
non-ideal diodes with specific V-I characteristic.
Clippers can be series or parallel type, based on the position of diode w.r.t. load. Further
these are classified as positive and negative clippers depending on the portion of half
cycle it clips off.
The clamping circuit clamps a signal to different D.C. Levels. The circuit must have a
capacitor a diode and a resistive element, and an independent DC supply to introduce an
additional shift. The magnitude of R&C must be chosen that the time constant t= RC is
large enough to ensure that the voltage across the capacitor does not discharge
significantly during the interval the diode is non-conducting. Clampers circuits can be
classified as positive and negative clampers. Those who shift positive part of waveform
are positive clampers, else negative clampers.

APPARATUS/COMPONENTS REQUIRED:

Bread Board
Diode (Si ) - IN001
Resistance - 1K
Capacitor - 1uF
Power supply - 0 – 10V DC
Connectors - 06
CRO and Function Generator

CIRCUIT DIAGRAM:
+Clipper,-clipper ,Dual Clipper

Paste tinkercad ckt here & mydaq ckt


PROCEDURE:

(A) CLIPPER CIRCUIT

Make connections as shown in the figures for clipper circuits on breadboard.


Apply an input signal of 1KHz and 20 V, using function generator & check the input on
CRO.
Connect CRO probes to output and observe the output waveforms.

(B) CLAMPER CIRCUIT

Make connections as shown in the figures for Clamper circuits on the bread board.
A pply on input signal of 1KHz & 20V using function generator & check the input on
CRO.
Plot the output waveform for each circuit.
Measure the voltage across capacitor & observe the output waveform on CRO.
Vary the input and observe the output on CRO.

EXPERIMENTAL DATA:

(I) OBSERVATION TABLE FOR Positive &negative &Dual CLIPPER CIRCUIT

S. No. Input Waveform Output Waveform


Vpp (V) Freq. (Hz) Vpp (V)
1
2
3
4
5
PRECAUTIONARY MEASURE TO BE TAKEN:

1. Before switch ON the power supply, make sure connections are proper:
2. No loose connections
3. Do not rotate the knobs of course and fine in power supply frequently.
4. Handle the electronic devices and equipments delicately

Conclusion

You might also like