CHEMICAL RESISTANCE OF

PLASTIC PIPING MATERIALS

TR-19
2020
 Foreword

This technical report was developed and published with the technical help and
financial support of the members of the Plastics Pipe Institute (PPI). These
members have shown their commitment to developing and improving quality
products by assisting standards development organizations in the development
of standards, and also by developing design aids and reports to help engineers,
code officials, specifying groups, contractors and users.

The purpose of this technical report is to provide information on the transport of

various chemicals using plastic piping materials.

PPI has prepared this technical report as a service to the industry. The
information in this report is offered in good faith and believed to be accurate at
the time of its preparation, but is offered “as is” without any express or implied
warranty, including WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. Additional information may be needed in some
areas, especially with regard to unusual or special applications. Consult the
manufacturer or material supplier for more detailed information. A list of member
manufacturers is available on the PPI website. PPI does not endorse the
proprietary products or processes of any manufacturer and assumes no
responsibility for compliance with applicable laws and regulations.

PPI intends to revise this technical report within five years, or sooner if required,
from the date of its publication, in response to comments and suggestions from
users of the document. Please send suggestions of improvements to the address
below. Information on other publications can be obtained by contacting PPI
directly or visiting our website.

The Plastics Pipe Institute, Inc.

https://www.plasticpipe.org/

This Technical Report, TR-19, was first issued in 1973 and was updated in
1983, 1991, 1999, 2000, 2007, and December 2020.

© 2020 The Plastics Pipe Institute, Inc.

ii
 Table of Contents

1.0 Introduction ...........................................................................................................1

2.0 Chemical Resistance in General ........................................................................... 2
2.1. Pipe and Fitting Materials ................................................................................2
2.2. Product Design and Joining Systems .............................................................. 3
2.3. Operating Conditions - Internal and External ................................................... 3
3.0 Types of Chemical Attack On Plastics ................................................................... 3
3.1. Permeation, Swelling, Plasticization, Solvation, and Extraction ....................... 3
3.2. Direct Chemical Attack ....................................................................................4
3.3. Environmental Stress Cracking ....................................................................... 5
4.0 Other Considerations ............................................................................................5
4.1. Chemical Families ...........................................................................................5
4.2. Accelerating Factors (Concentration, Temperature, Stress) ............................ 6
4.3. Combinations of Chemicals .............................................................................6
4.4. Multi-Layered (Composite) Piping ................................................................... 7
4.5. Rate of Chemical Attack ..................................................................................7
5.0 Chemical Resistance Data for Plastic Piping in Non-Pressure Applications and
Data Table ............................................................................................................7

List of Tables

Table 1: Plastic Materials Identification............................................................................ 2

Table 2: Resistance Codes .............................................................................................8
Table 3: List of Chemical Resistances (°F) .................................................................... 10

iii
 CHEMICAL RESISTANCE OF PLASTIC PIPING MATERIALS

1.0 INTRODUCTION

This technical report has been developed as an informative guide on the

resistance of plastic piping and fitting materials to chemical attack.

It is divided into several sections:

• Section 2.0: Chemical resistance in general, and considerations for end

use applications
• Section 3.0: Types of chemical attack on plastics
• Section 4.0: Other considerations
• Section 5.0: Chemical Resistance Data for Plastic Piping in Non-
Pressure Applications and Data Table

Listings of chemical resistance data are presented in Table 3 for common

plastic piping materials applicable to non-pressure applications.

Determination of suitability for specific applications under stress (e.g.

pressurized service) is beyond the scope of this report. Users should contact
the specific pipe or fitting manufacturer for recommendations on pressurized
applications.

Note 1: Drinking water, also known as potable water, is water that is safe to drink or to
use for food preparation. Across North America, the majority of the drinking
water that is provided in public water systems is treated with a disinfectant to
control the growth of harmful microorganisms. Potable water disinfectants
include chlorine, chloramines, and rarely, chlorine dioxide. Piping materials
intended for treated water must be resistant to such disinfectants at various
levels, as described in product standards.

For specific information about the resistance of crosslinked polyethylene

(PEX) to disinfectants, please see PPI Technical Note-53 Guide to Chlorine
Resistance Ratings of PEX Pipes and Tubing for Potable Water
Applications and PPI Statement A Relative Oxidative Aggressiveness of
Chloramines and Free Chlorine Disinfectants on Crosslinked
Polyethylene (PEX) Pipes used in Treated Potable Water.

For specific information about the resistance of high-density polyethylene

(HDPE) to disinfectants, please see PPI Technical Note-44 Long Term
Resistance of AWWA C906 Polyethylene (PE) Pipe to Potable Water
Disinfectants and PPI Technical Note-49 Recommendations for AWWA
C901 Service Tubes in Potable Water Applications.

1
 For specific information about the resistance of chlorinated polyvinyl chloride
(CPVC) to disinfectants, please see Section 4: Effects of Potable Water
Disinfectants on CPVC of PPI Technical Note-62 Suitability and Fitness of
CPVC Piping Systems for Commercial Building Applications.

2.0 CHEMICAL RESISTANCE IN GENERAL

Plastic pipe and fitting materials are generally resistant to attack from many
chemicals. This inherent property makes them suitable for use in numerous
fluid and gas transport applications.

However, there are certain chemicals that may damage plastic pipes, either
through exposure on the outside of the pipe to chemicals, on the internal
surface of the pipe during the transport of such chemicals, or with exposure to
inert fluids containing chemicals in various concentrations.

Each material has unique resistance to chemicals in various situations. The

suitability of a pipe or fitting system for use in a particular fluid or gas
application is a function of several factors, described below:

2.1. Pipe and Fitting Materials

The specific plastic material used in pipe and fittings impacts its
chemical resistance. This report includes the materials listed in
Table 1 Plastic Materials Identification.
Table 1: Plastic Materials Identification
ABS acrylonitrile-butadiene-styrene
CPVC chlorinated polyvinyl chloride
PP polypropylene
PP-R 1 polypropylene random copolymer
PP-RCT 1 polypropylene random copolymer with modified crystallinity and
temperature resistance
PVC polyvinyl chloride
PE polyethylene (representative of medium density polyethylene [MDPE]
and high density polyethylene [HDPE]; not representative of low density
polyethylene [LDPE])
PE-RT 2 polyethylene of raised temperature resistance
PB Polybutylene
PVDF polyvinylidene fluoride
PEX crosslinked polyethylene
PA11/ PA12 polyamide 11 / polyamide 12
PSU Polysulfone
PPSU Polyphenylsulfone

1
PP-R and PP-RCT are chemically similar to PP and are grouped together in Table 3; they may
be assumed to have similar chemical resistance
2
PE-RT is chemically similar to MDPE and HDPE and are grouped together in Table 3; they may
be assumed to have similar chemical resistance

2
 2.2. Product Design and Joining Systems

Piping dimensions, including wall thickness, construction, and

composition (layers, fillers, etc.), can affect chemical resistance.

The type of joining system can also affect the performance of the
system in chemical handling applications. Heat fusion and solvent
cementing do not introduce different materials into the system. The
resistance of solvent cement to certain chemicals can vary from
grade to grade.

Other components and appurtenances in the piping system can

have different chemical resistances. Certain types of mechanical
joints include gaskets using elastomers with their own unique
resistances. Some piping systems include other plastic or non-
plastic materials used as mechanical fitting components which can
have different chemical resistance.

2.3. Operating Conditions - Internal and External

o Chemicals or mixtures of chemicals, and their concentrations.

o Operating temperature — maximum, minimum, and cyclical
variations.
o Operating pressure or applied stress — maximum, minimum and
cyclical variations.

3.0 TYPES OF CHEMICAL ATTACK ON PLASTICS

In general, chemicals that affect plastics do so in several ways, including

solvation, chemical attack, and environmental stress cracking.

3.1. Permeation, Swelling, Plasticization, Solvation, and Extraction

Permeation is the transport of chemicals through the pipe wall via

diffusion through the free volume of the polymer matrix without
significant change in the material properties. Permeability may be of
interest in situations where the pipe is to function as a liner pipe for a
less resistant material (e.g., fiberglass or steel), where the pipe is
transporting particularly hazardous substances, or where the pipe is
installed in contaminated soil.

Permeability of specific plastic piping materials is not addressed in

this document. PPI Statement N Barrier Properties of Plastic
Pipe Used for Potable Water Service, states “In areas of known or
suspected contamination, the design of the distribution system
should be based on a careful analysis of the situation.

3
 Appropriate technical data and individual manufacturers’
recommendations should be consulted on the overall design of a
pipe system for these systems.”

Note 2: See also PPI Comments on Permeation of Water Pipes and on the AWWA-
RF Report on Hydrocarbons at https://plasticpipe.org/pdf/ppi-comment-
permeation-hydrocarbons.pdf

Absorption occurs when a chemical diffuses into the free volume of

the polymer matrix and accumulates there. This may result in one or
more of the following effects: swelling, plasticization, or solvation. In
the case of absorption, physical properties may be affected, but the
polymer molecule itself is not chemically changed, degraded or
destroyed.

Swelling is an increase in the bulk volume of a material caused by

the absorption of liquids or vapors from the environment. It may or
may not be accompanied by plasticization, which results in softening
and loss of strength in the material.

In extreme cases, the solvating compound can fully dissolve the

plastic material.

Sometimes the polymer itself may not be soluble, but it may contain
a soluble formulary ingredient that may be extracted from the
polymer compound. This is more common in plasticized materials
where loss of plasticizer may result in embrittlement. It is not
common in plastic materials used for pipes and fittings and is not
addressed in this document.

In gas or vapor transmission service, there may be a very slight loss

of contents through the pipe wall.

Lastly, a solvating or permeating chemical entrained in the material

may be released when heat fusion or solvent cement joining is
performed. Thus, heat fusion (e.g. welding) or solvent cement
joining may be unreliable if performed on permeated pipes. Caution
should be used in performing these processes if solvation or
permeation are suspected.

3.2. Direct Chemical Attack

Direct chemical attack occurs when exposure to a chemical causes

a chemical alteration of the polymer molecules by chain scission,
crosslinking, oxidation, or substitution reactions.

4
 Direct chemical attack frequently causes a severe reduction of
mechanical physical properties such as tensile strength, ductility,
burst pressure, and impact resistance.

Chemical resistance may vary greatly from one plastic material to

another (i.e., PVC, ABS, PE, etc.), and also among different cell
classifications of the same plastic type (e.g. PVC 1120 to PVC 2110,
PE 3608 to PE 4710, etc.). There may also be slight variations
among commercial products having the same cell classification,
based on compound ingredients known as stabilizers or “additive
packages”.

The chemical resistance of plastic piping and fittings is basically a

function of the chemical resistance of the plastic material, including
additives and other ingredients in the final compound. In general, the
fewer filler ingredients used, the better the chemical resistance.
Plastic pipes with significant filler percentages may be susceptible to
chemical attack whereas an unfilled material may be affected to a
lesser degree or not at all.

3.3. Environmental Stress Cracking

Environmental stress cracking (ESC) is defined as the “development

of cracks in a material that is subjected to stress or strain in the
presence of specific chemicals”, as per ASTM F412 Standard
Terminology for Plastic Piping Systems.

Environmental stress cracking is a fundamentally different

phenomenon than chemical attack, even though they may present
similarly (e.g. crazing or whitening of parts, sloughing of material,
minor crack formation). ESC does not result in chemical alteration of
the polymer molecule. ESC is caused by a chemical agent in
combination with inherent and applied stresses. It can often be
minimized with proper installation. Direct chemical attack does not
require any stress or strain on the material in order to occur,
although it may be accelerated in conditions of high stress or strain.

4.0 OTHER CONSIDERATIONS

4.1. Chemical Families

While the effect of each individual chemical is specific, some

chemicals can be grouped into general categories based on
similarities in chemical characteristics (acids, bases, alcohols, etc.).
For example, water-based (aqueous) solutions of neutral inorganic
salts generally have the same effect on plastic piping materials as
water alone; thus, sodium chloride, potassium alum, calcium

5
 chloride, copper sulfate, potassium sulfate and zinc chloride
solutions have the same effect as water.

However, at elevated temperatures or high concentrations, some

salt solutions may attack some plastic materials through either
oxidation or chemical substitution when they would be benign at
lower temperatures and concentrations.

4.2. Accelerating factors (concentration, temperature, stress)

Generally, the resistance of a particular plastic to a specific chemical

will decrease with an increase in concentration. For example, for
some materials, dilute sulfuric acid may be acceptable, whereas
95% sulfuric acid may not.

The resistance of a particular plastic to a specific chemical generally

decreases as temperature increases because the rate of chemical
phenomenon (i.e. reactivity, permeation rate, solvation) tends to
increase. This rate increase is logarithmic with respect to
temperature over most plastic functional temperatures and generally
follows to the Arrhenius equation.

The chemical resistance of a particular plastic generally decreases

with increasing applied stress. This is commonly seen when the
presence of certain chemicals causes environmental stress cracking
where unstressed parts exhibit good chemical resistance.

The chemical resistance of a particular plastic generally decreases

where temperature or applied stress are varied or cycled. These
effects can be greater overall in combination. Testing should be
conducted if the system is expected to perform across a wide range
of temperatures and stresses to determine the overall combined
effect.

4.3. Combinations of Chemicals

In some cases, combinations of chemicals may have a synergistic

effect on damaging a plastic material, and a mixture may cause
damage where the individual chemicals do not. It cannot be
assumed that an individual chemical’s lack of effect would apply for
combinations that include several chemicals. When the possible
combined effect of several chemicals is unknown, the material
should be tested in the complete chemical mixture(s) in question.

6
 4.4. Multi-Layered (Composite) Piping

Some piping products utilize a multi-layered (composite)

construction, in which the pipe wall is constructed of layers of
different materials. The layers may consist of both plastic and non-
plastic.

For example, PE/AL/PE and PEX/AL/PEX pipes contain mid-wall

aluminum layers. Examples of all-plastic composite pipes include
PVC/ABS/PVC and fiber-core PP-R or PP-RCT pipes. Layered
composite material pipes may have chemical resistance that differs
from the chemical resistance of the individual materials.

4.5. Rate of Chemical Attack

Chemicals that attack plastics do so at a certain rate, some slowly

and some more quickly. But usually, any chemical attack is
increased when temperature or stress are increased, or when
temperature or stress are varied. The particular rate of chemical
attack must be taken into consideration in the life-cycle evaluation
for a particular application. Each combination of material cost,
installation cost and service life must be evaluated and judged on its
own merits.

In certain cases involving a slow rate of chemical attack, particularly

when the application will be pressurized, simple immersion data, like
that represented in Table 3, may not adequately characterize
performance throughout the intended design life. Longer-term
testing to replicate service conditions is advisable to fully measure
the effects of these chemicals.

5.0 CHEMICAL RESISTANCE DATA FOR PLASTIC PIPING IN NON-

PRESSURE APPLICATIONS and DATA TABLE

When plastic pipes come into contact with chemical agents it is important to
know how the pipe may be affected. For non-pressure applications, where the
pipe is not subject to continuous internal pressure or stress, chemical
immersion test data may provide suitable information. The pipe manufacturer
may have additional data from similar tests, or information on previous
installations under similar field conditions.

7
 The following cautions apply to Table 3 List of Chemical Resistances:

• Data Sources. The information in Table 3 has been obtained from

numerous sources. The data are based primarily on plastic material test
specimens that have been immersed in the chemical and evaluated,
and to a lesser degree, on field-experience. In most cases, detailed
information on the test conditions (e.g. exposure time), and on test
results (e.g. change in weight, change in volume, and change in
strength) was not available. Therefore, this information is best used only
for comparison of different plastic materials.
• Combinations of Chemicals. Chemicals that individually do not have an
effect may affect the pipe if combined with certain other chemicals. The
list of possible combinations of chemicals is endless. Table 3 does not
address chemical combinations.
• Composite Piping. Layered composite piping may have chemical
resistance that differs from that of the individual materials in the layers.
Table 3 is not applicable to layered composite piping products.
• Applicability to fiberglass and filled materials. Table 3 is not applicable
to reinforced epoxy resin (fiberglass) pipes, and to plastic pipes
containing significant percentages of filler materials.
• Concentrations. Where no concentrations are given (indicated as ‘P’),
the commercially pure material is indicated, except in the case of solids
where saturated aqueous solutions are indicated.

See Table 2 for the Resistance Codes which are used throughout Table 3.
Table 2: Resistance Codes

Code Meaning Typical Result

Plastic material is generally Swelling < 3% or weight loss < 0.5%
Resistant up to the temperature and elongation at break not
R to xx°F (°F) indicated by code and may significantly changed
have limited resistance at higher Typical performance properties not
temperatures significantly affected
Material may experience swelling in
Plastic material has Limited
the range of 3 - 8% or weight loss
resistance at the temperature
of 0.5 - 5% and/or reduction in
L to xx°F (°F) indicated by code.
elongation at break by < 50%
Compatibility at lower
temperatures should not be
Some effect on performance
assumed
properties
Material may experience swelling >
8% or weight loss > 5% and/or
N Plastic material is Not resistant.
reduction in elongation at break
by > 50%
P Pure Concentration
Data not available
—
Check with piping manufacturer

8
Chemicals that do not normally affect the properties of an unstressed plastic
may cause completely different behavior (such as stress cracking) when
under mechanical stress, such as constant internal pressure or mechanical
stress cycles.

Unstressed immersion test chemical resistance information is applicable only

when the plastic pipe will not be subject to mechanical load or stress that is
constant, or cycles frequently.

When the pipe will be subject to a continuous applied mechanical stress or to

combinations of chemicals, testing that duplicates the expected field
conditions, as closely as possible, should be performed on representative
samples of the pipe product to properly evaluate that plastic pipe for use in
this application.

9
 ***May not be fully applicable to pressurized applications***

Table 3: List of Chemical Resistances (°F)

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)

Acetaldehyde 40% --- N --- L to 73 R to 73 --- N R to 73 --- --- ---

CAS# 75-07-0 Pure --- N R to 140 N L to 73 L to 73 --- L to 140 L to 176 R to 73 ---
CH3 CHO
Acetamide
CAS# 60-35-5 5% R to 120 --- R to 140 --- R to 140 --- --- R to 140 --- --- ---
CH3 CONH2
Acetic Acid vapor R to 120 R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 64-19-7 10% --- R to 180 --- --- --- --- R to 248 R to 180 R to 176 --- ---
CH3 COOH 25% N N R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
40% --- --- --- --- --- --- R to 140 --- --- --- ---
50% --- --- --- --- --- --- R to 140 --- L to 68 --- ---
60% N N R to 180 R to 73 R to 73 R to 73 R to 104 --- --- --- ---
85% N N R to 120 R to 73 R to 73 R to 73 --- --- --- R to167 R to 167
glacial N N R to 120 R to 73 R to 73 R to 73 R to 104 R to 68 --- R to 167 R to 167
Acetic Anhydride
CAS# 108-24-7 --- N N R to 73 N R to 73 R to 140 N R to 73 L to 68 --- ---
(CH3 CO)2 O
R to
Acetone 5% N R to 73 N L to 73 R to 140 R to 212 L to 73 L to 140 N ---
180
CAS# 67-64-1 10% --- L to 180 --- --- --- --- R to 122 --- --- --- ---
CH3 COCH3 100% --- N --- --- --- --- --- --- --- --- ---
Acetophenone
CAS# 98-86-2 --- N N R to 120 -- R to 73 --- R to 68 R to 73 --- --- ---
C6 H5 COCH3
Acetyl Chloride
CAS# 75-36-5 --- N N --- N --- --- N --- --- --- ---
CH3 COCl

10
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Acetylene
CAS# 74-86-2 gas 100% R to 73 N R to 73 N R to 73 L to 73 --- R to 73 R to 140 --- ---
HC≡CH
Acetylnitrile --- --- N --- N --- --- --- --- --- --- ---
Acrylic Acid
CAS# 79-10-7 97% --- N --- N R to 140 --- --- R to 140 --- --- ---
H2 C=CHCOOH
Acrylonitrile
CAS# 107-13-1 --- --- N --- N R to 140 --- --- R to 140 --- --- ---
H2 C=CHC≡N
Adipic Acid
CAS#124-04-9 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 73 R to 176 R to 140 --- --- ---
COOH(CH2 )4 COOH
Allyl Alcohol
CAS# 107-18-6 96% --- L to 73 R to 140 R to 73 N R to 140 --- L to 100 --- --- ---
CH2 = CHCH2 OH
Allyl Chloride -- --- N --- N L to 73 --- R to 140 L to 73 --- --- ---
CAS# 107-05-1 Liquid --- --- --- --- --- --- R to 68 --- --- --- ---
CH2=CHCH2 Cl
Aluminum Ammonium
Sulfate (Alum)
CAS# 7784-25-0 Saturated --- R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---

AlNH4 (SO4 )2 •12H 2O

Aluminum Chloride
CAS# 7446-70-0 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
AlCl3
Aluminum Fluoride
Anhydrous
CAS# 7764-18-1 Saturated R to 160 R to 180 R to 180 R to 73 R to 140 R to 140 R to 212 R to 140 --- --- ---
AlF3

11
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Aluminum Hydroxide
CAS# 21645-51-2 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Al(OH)3
Aluminum Nitrate
CAS# 13473-90-0 Saturated --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Al(NO3 )3 •9H2 O
Aluminum Oxychloride
-- --- R to 180 R to 180 R to 140 --- R to 140 --- --- --- --- ---
CAS# 1327-41-9
Aluminum Potassium Sulfate
(Alum)
CAS# 10043-67-1 Saturated R to 160 R to 180 R to 140 R to 140 R to 140 --- R to 212 R to 140 --- --- ---

AlK(SO4 )2 •12H2 O
Aluminum Sulfate
CAS# 10043-01-3 Saturated R to 160 R to 180 R to 140 R to 140 R to 140 C to 73 R to 212 R to 140 R to 194 --- ---
Al2 (SO4 )3
Ammonia Gas
CAS# 7664-41-7 100% N N R to 140 R to 140 R to 140 R to 140 --- R to 140 R to 140 --- ---
NH3
Ammonium Acetate
CAS# 631-61-8 Saturated R to 120 R to 180 R to 73 R to 140 R to 140 --- R to 212 R to 140 --- --- ---
CH3COONH4
Ammonium Bifluoride
CAS# 1341-49-7 Saturated --- R to 180 R to 180 R to 140 --- R to 140 --- R to 140 --- --- ---
NH4 HF2

Ammonium Bisulfide
CAS# 12124-99-1 --- --- --- --- R to 140 --- --- --- --- --- --- ---
(NH4)HS
Ammonium Carbonate
CAS# 506-87-6 Saturated --- R to 180 R to 212 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
(NH4)2CO3

12
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Ammonium Chloride
CAS# 12125-02-9 Saturated R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NH4Cl
Ammonium Dichromate
CAS# 7789-09-5 -- --- R to 73 --- R to 73 --- --- --- --- --- --- ---
(NH4)2Cr 2O7
Ammonium Fluoride 10% R to 120 R to 180 R to 212 R to 140 R to 140 --- R to 212 R to 140 --- --- ---
CAS# 12125-01-8 25% R to 120 R to 180 R to 212 L to 140 R to 140 R to 73 --- R to 140 --- --- ---
NH4 F
Ammonium Hydroxide 10% R to 120 N R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 1336-21-6 30% --- --- --- --- R to 140 --- --- R to 140 --- --- ---
NH4 OH Saturated --- --- --- --- --- --- --- R to 194 --- --- ---
Ammonium Metaphosphate
CAS# 13446-46-3 Saturated -- -- R to 212 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
NH3 HPO3
Ammonium Nitrate
CAS# 6484-52-2 Saturated R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NH4 NO3
Ammonium Persulfate
CAS# 7727-54-0 --- --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
(NH4)2 S2 O8
Ammonium Phosphate
(Monobasic)
CAS# 7722-76-1 --- R to 120 L to 73 R to 212 R to 140 R to 140 R to 140 R to 248 R to 140 --- R to 199 R to 199

NH4 H2 PO4
Ammonium Sulfate
CAS# 7783-20-2 Saturated R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
(NH4 )2 SO4
Ammonium Sulfide dilute R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 12135-76-1 Saturated --- --- --- --- R to 140 --- --- --- --- --- ---
(NH4 )2 S

13
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Ammonium Thiocyanate
CAS# 1762-95-4 50-60% R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 73 --- --- ---
NH4 SCN
Amyl Acetate
CAS# 628-63-7 -- N N N N R to 73 --- R to 122 R to 73 C to 194 --- ---
CH3 COOC5 H11
Amyl Alcohol -- --- N --- N R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 75-41-0 100% --- --- --- --- --- L to 140 --- --- --- --- ---
C5 H11 OH
n-Amyl Chloride
CAS# 543-59-9 -- N N N N L to 73 --- --- L to 73 --- --- ---
CH3 (CH2) 3CH 2Cl
Aniline
CAS# 62-53-3 -- N N --- N R to 73 L to 140 R to 68 L to 140 --- --- ---
C6 H5 NH2
Aniline Chlorohydrate -- --- N --- N L to 73 N --- L to 73 --- --- ---
Aniline Hydrochloride
CAS# 142-04-1 Saturated --- N --- N R to 140 N --- R to 140 --- --- ---
C6 H5 NH2 •HCl
Anthraquinone
CAS# 84-65-2 -- --- R to 180 --- R to 140 L to 73 L to 73 --- L to 73 --- --- ---
C14H8O2
Anthraquinone Sulfonic Acid
CAS# 82-49-5 -- --- R to 180 R to 73 R to 140 R to 140 L to 73 --- L to 73 --- --- ---
C14 H7 O2 • SO3 • H2O
Antimony Trichloride
CAS# 10025-91-9 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 140 R to 140 --- --- ---
SbCl3

14
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Aqua Regia
CAS# 8007-56-5
-- N R to 73 N L to 73 N N L to 194 N --- N ---
(Nitrohydrochloric Acid)
HCl+HNO3
Arsenic Acid
CAS# 7778-39-4 80% --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
H3 AsO4

Asphalt
-- --- N R to 73 N R to 73 R to 140 --- R to 73 --- --- ---
CAS# 8052-42-4
Barium Carbonate
CAS# 513-77-9 Saturated R to 120 R to 180 R to 140 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
BaCO3
Barium Chloride
CAS# 10361-37-2 Saturated R to 120 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 R to 194 --- ---
BaCl2 •2H2O
Barium Hydroxide 30% --- --- --- --- R to 140 --- --- R to 140 --- --- ---
CAS# 17194-00-2 Saturated R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 212 --- --- ---
Ba(OH)2
Barium Nitrate
CAS# 10022-31-8 Saturated R to 73 R to 180 R to 140 R to 73 R to 140 --- --- R to 140 --- --- ---
Ba(NO3 )2
Barium Sulfate
CAS# 7727-43-7 Saturated R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
BaSO4
Barium Sulfide
CAS# 21109-95-5 Saturated R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 248 --- --- ---
BaS
Beer -- R to 120 R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 140 R to 68 --- ---
Beet Sugar Liquors -- --- R to 180 R to 180 R to 140 R to 73 R to 140 --- R to 73 --- --- ---

15
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Benzaldehyde
CAS# 100-52-7 10% N N R to 73 R to 73 R to 73 L to 73 --- R to 73 R to 104 --- ---
C6 H5 CHO
Benzene
CAS# 71-43-2 -- N N N N N N N N --- N ---
C6 H6
Benzene Sulfonic Acid 10% --- R to 180 R to 180 R to 140 R to 73 --- --- R to 73 --- --- ---
CAS# 98-11-3 10%+ --- N --- N --- --- --- --- --- --- ---
C6 H5 SO3 H
Benzoic Acid
CAS# 65-85-0 R to
100% R to 160 R to 180 R to 73 R to 140 R to 140 R to 140 --- --- --- ---
140
C6 H5 COOH
Benzoyl Chloride
CAS# 99-88-4 Sat. Sol. --- --- --- --- --- --- L to 68 --- --- --- ---
C6H5COCl
Benzyl Alcohol
CAS# 100-51-6 -- --- N R to 120 N R to 140 --- R to 122 R to 140 R to 68 --- ---
C6 H5 CH2 OH
Benzyl Chloride
CAS# 100-44-7 -- --- N --- --- --- --- --- R to 140 --- --- ---
C7H7Cl
Bismuth Carbonate
CAS#5892-10-4 Saturated --- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
(BiO)2 CO3
Black Liquor Saturated --- R to 180 R to 140 R to 140 R to 120 R to 140 --- R to 120 --- --- ---
Bleach-See Sodium
Hypochlorite
Borax
CAS# 1303-96-4 Saturated R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na2 B4 O7 •10H2O

16
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Boric Acid
CAS# 10043-35-3 Saturated R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- R to 113 ---
H3 BO3
Bromic Acid Saturated --- R to 180 N R to 140 N R to 140 R to 212 N --- --- ---
CAS# 15541-45-4 10% --- --- --- --- R to 140 --- --- --- --- --- ---
HBrO3
Bromine Liquid R to 73 N N N N N R to 248 N N --- ---
CAS# 7726-95-6 vapor 25% --- R to 180 N R to 140 N --- --- N --- --- ---
Br2
Bromine Water Saturated --- R to 180 N R to 140 N L to 73 R to 176 N --- --- ---
Bromobenzene
CAS# 108-86-1 -- --- N --- N --- --- --- --- --- --- ---
C6 H5 Br
Bromotoluene
(Benzyl bromide)
-- --- N L N --- --- --- --- --- --- ---
CAS# 95-46-5
C6 H5 CH2 Br
Butadiene 50% --- --- N R to 140 R to 73 --- --- R to 73 --- --- ---
CAS# 106-99-0 Gas --- --- --- --- --- --- R to 212 --- --- --- ---
H2 C=CHCH=CH2
Butane 50% --- R to 180 R to 140 R to 140 R to 140 N --- R to 140 --- --- ---
CAS# 106-97-8 Gas --- --- --- --- --- --- R to 68 --- --- --- ---
C4 H10
n-Butanol
CAS# 71-36-3 Liquid --- L to 73 --- --- --- --- R to 140 --- --- N ---
C4 H9OH
Butyl Acetate
CAS# 123-86-4 100% N N L to 73 N L to 73 L to 73 L to 104 L to 73 R to 194 --- ---
CH3COOCH2CH2CH2CH3

17
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Butyl Alcohol
CAS# 71-36-3 -- --- L to 73 R to 180 R to 140 R to 140 R to 140 --- R to 140 L to 104 R to 73 ---
CH3 (CH2 )2 CH 2OH
Butyl Cellosolve
CAS# 111-76-2 -- --- N --- R to 73 --- --- --- --- --- --- ---
HOCH2 CH2 O(CH2 )3CH3
n-Butyl Chloride
CAS# 109-69-3 -- N N --- --- --- --- --- --- --- --- ---
C4 H9 Cl
Butyl Glycol
CAS# 111-76-2 Liquid --- N --- --- --- --- R to 212 --- --- --- ---
HOCH2 CH2 O(CH2 )3CH3
Butylene
CAS# 107-01-7 (isomer not
Liquid --- --- N R to 140 N --- --- N --- --- ---
specified)
CH3 CH=CHCH3
Butyl Phenol
CAS# 98-54-4 -- --- --- N L to 73 R to 73 R to 73 --- R to 73 --- --- ---
(CH3)3C6H4OH
Butyl Phthalate
CAS# 84-74-2 -- --- N R to 180 --- --- --- R to 140 --- --- --- ---
C16H22O4
Butyl Stearate
CAS# 123-95-5 -- --- --- --- R to 73 --- --- --- --- --- --- ---
CH3(CH2)16COO(CH2)3CH3
Butynediol
CAS# 110-65-6 -- --- --- --- R to 73 --- --- ---- --- --- --- ---
HOCH2 C≡CCH 2OH
Butyric Acid -- N N R to 180 R to 73 R to 73 R to 73 --- R to 73 --- --- ---
CAS# 107-92-6 20% --- --- --- --- --- --- R to 212 --- --- --- ---
CH3 CH2 CH2 COOH Liquid --- --- --- --- --- --- R to 176 R to 73 --- --- ---

18
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Cadmium Cyanide
CAS# 542-83-6 -- --- R to 180 --- R to 140 --- --- --- --- --- --- ---
Cd(CN)2
Calcium Bisulfide
-- --- R to 180 --- N R to 140 --- --- R to 140 --- --- ---
Ca(HS)2 o6H 2O
Calcium Bisulfite -- --- R to 180 R to 180 R to 140 N R to 140 --- N --- --- ---
CAS# 13780-03-5 Saturated --- --- --- --- --- --- R to 248 --- --- --- ---
Ca(HSO3 )2
Calcium Carbonate
Saturated --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
CaCO3
Calcium Chlorate
CAS# 10137-74-3 -- --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
Ca(ClO3 )2 •2H2 O
Calcium Chloride
CAS# 10043-52-4 Saturated R to 120 R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 176 R to 194 --- ---
CaCl2
Calcium Hydrogen Sulfide
CAS# 9046-53-1 >10% --- --- --- --- --- --- R to 248 --- --- --- ---
Ca(HS)2
Calcium Hydroxide -- R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 1305-62-0 30% --- --- --- --- R to 140 --- --- R to 140 --- --- ---
Ca(OH)2
Calcium Hypochlorite 30% R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7778-54-3 Saturated --- --- --- --- --- --- L to 212 --- --- --- ---
Ca(OCl)2
Calcium Nitrate -- --- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 10124-37-5 50% --- --- --- --- R to 140 --- R to 212 R to 140 --- --- ---
Ca(NO3 )2 Saturated --- --- --- --- --- --- R to 176 --- --- --- ---

19
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Calcium Oxide
CAS# 1305-78-8 -- --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
CaO
Calcium Sulfate
CAS# 7778-18-9 -- R to 100 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CaSO4
Camphor
CAS# 76-22-2 -- N --- R to 73 R to 73 R to 73 --- --- R to 73 --- --- ---
C10 H16 O
Cane Sugar Liquors
(Sucrose)
CAS# 57-50-1 -- --- R to 180 R to 180 R to 140 R to 140 R to 150 --- R to 140 --- --- ---
C12 H22 O11
Carbitol
CAS# 111-90-0 -- --- N --- R to 73 --- --- --- --- --- --- ---
CH3CH2O(CH2)2O(CH2)2OH
Carbon Dioxide Dry 100% R to 160 R to 180 R to 140 R to 140 R to 140 --- R to 212 R to 140 --- --- ---
CAS# 124-38-9 Wet R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CO2
Carbon Disulfide
CAS# 75-15-0 -- N N N N L to 140 --- --- L to 73 R to 104 N ---
CS2
Carbon Monoxide
CAS# 630-08-0 Gas --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 140 R to 140 --- --- ---
CO
Carbon Tetrachloride
CAS# 56-23-5 -- N N N R to 73 L to 73 N L to 212 L to 68 N N ---
CCl4
Carbonic Acid
CAS# 463-79-6 Saturated R to 185 R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
H2 CO3

20
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Castor Oil
-- --- L to 180 R to 140 R to 140 R to 73 R to 140 --- R to 73 --- --- ---
CAS# 8001-79
Caustic Potash
CAS# 1310-58-3 50% R to 160 R to 180 R to 180 R to 140 R to 140 R to 73 --- R to 140 --- --- ---
KOH
Cellosolve
-- --- N R to 73 R to 73 L to 120 R to 140 --- L to 120 --- N ---
CAS# 110-80-2
Cellosolve Acetate
CAS# 111-15-9 -- --- N R to 73 R to 73 --- --- --- --- --- --- ---
CH3 COOCH2 CH2 OC2 H5
Chloral Hydrate
CAS# 302-17-0 All --- --- L to 73 R to 140 R to 120 R to 140 --- R to 120 --- --- ---
CCl3 CH (OH)2
Chloramine
CAS# 10599-90-3 Dilute --- R to 180 R to 73 R to 73 R to 73 --- --- R to 73 --- --- ---
NH2 Cl
Chloric acid 10% --- R to 180 R to 73 R to 140 R to 73 --- --- R to 73 --- --- ---
CAS# 7790-93-4 20% --- R to 185 R to 73 R to 140 R to 73 --- --- R to 73 --- --- ---
HClO3
Chlorine Gas 0-20 PPM
N L to 73 N L to 73 L to 73 --- R to 212 L to 73 --- --- ---
CAS# 7782-50-5 moisture content
Cl2 20-50 PPM
N L to 73 N N L to 73 --- --- L to 73 --- --- ---
moisture content
50+ PPM
N L to 73 N N L to 73 --- N L to 73 --- --- ---
moisture content
Chloroacetic Acid 50% N N L to 73 R to 140 R to 120 N --- R to 120 --- --- ---
CAS# 79-11-8 >10% --- --- --- --- --- --- R to 140 --- --- --- ---
CH2 ClCOOH

21
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Chloroacetyl Chloride
CAS# 79-04-9 -- --- N --- R to 73 --- --- --- --- --- --- ---
ClCH2 COCl
Chlorobenzene Dry N N R to 73 N L to 73 N --- L to 73 --- --- ---
CAS# 108-90-7 Liquid --- --- --- --- --- --- R to 140 R to 68 L to 176 --- ---
C6 H5 Cl
Chlorobenzyl Chloride
CAS# 104-83-6 -- --- N --- N L to 120 --- --- L to 120 --- --- ---
ClC6 H4 CH2 Cl
Chloroethanol
CAS# 107-07-3 Liquid --- N --- --- --- N R to 122 --- --- --- ---
ClCH2CH2OH
Chloroform Dry N N N N L to 73 L to 73 --- N --- N ---
CAS# 67-66-3 Liquid --- --- --- --- --- --- R to 212 N --- --- ---
CHCl3
Chloromethane
CAS# 74-87-3 Gas --- N --- --- --- --- R to 212 --- --- --- ---
CH3Cl
Chloropicrin
CAS# 76-06-2 -- --- N --- N R to 73 --- --- R to 73 --- --- ---
CCl3 NO2
Chlorosulfonic Acid -- --- R to 73 N R to 73 L to 120 N --- N --- --- ---
CAS# 7790-94-5 50% --- --- --- --- --- --- R to 68 --- --- --- ---
ClSO2 OH 100% --- --- --- --- N --- --- N --- --- ---
Chromic Acid Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
CAS# 7738-94-5 10% R to 73 R to 180 R to 140 R to 140 R to 73 R to 140 R to 212 R to 73 N N N
H2 CrO4 30% N R to 180 R to 73 R to 140 R to 73 R to 140 R to 212 R to 73 --- N N
40% N R to 180 R to 73 R to 140 R to 73 R to 73 R to 212 R to 73 --- N N
50% N L to 140 R to 73 N R to 73 N R to 212 R to 73 --- N N

22
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Chromium Potassium Sulfate
>10% --- --- --- --- --- --- R to 212 --- --- --- ---
(dodecahydrate)
CAS# 7788-99-0 -- --- --- R to 73 --- R to 73 --- --- R to 73 --- --- ---
CrK(SO4)2 •12H2 O Saturated --- --- --- --- --- R to 212 --- --- --- --- ---
Citric Acid CAS# 77-92-9
Saturated R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 R to 248 R to 140 L to 140 --- L
C6 H8 O7
Coconut Oil
-- --- L to 180 R to 73 R to 140 R to 73 R to 140 R to 248 R to 73 --- --- ---
CAS# 8001-31-8
Cod Liver Oil Work Sol. --- L to 180 --- --- --- --- R to 248 --- --- --- ---
Coffee -- --- R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- R to 203 R to 203
Coke Oven Gas -- --- --- R to 73 R to 140 R to 140 --- --- R to 140 --- --- ---
Copper Acetate
CAS# 142-71-2 Saturated --- R to 73 R to 73 R to 73 --- --- --- --- --- --- ---
Cu(C2 H3 O2 )2 •H2 O
Copper Carbonate
CAS # 12069-69-1 Saturated --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
CuCO3

Copper Chloride
CAS# 7447-39-4 Saturated R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CuCl2
Copper Cyanide
CAS# 544-92-3 Saturated --- R to 180 --- R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CuCN
Copper Fluoride Dihydrate
CAS# 13454-88-1 2% --- R to 180 R to 73 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CuF2 •2H2 O
Copper Nitrate 30% --- R to 180 R to 140 R to 140 R to 140 R to 140 --- --- --- --- ---
CAS# 3251-23-8 50% --- --- --- --- --- --- R to 212 --- --- --- ---
Cu(NO3)2 •3H2 O

23
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Copper Sulfate
CAS#7758-99-8 Saturated R to 120 R to 180 R to 120 R to 140 R to 140 R to 140 R to 212 R to 140 R to 194 --- ---
CuSO4 •5H2 O
Corn Oil
-- --- L to 180 R to 73 R to 140 R to 120 --- --- R to 120 --- R to 200 ---
CAS# 8001-30-7
Corn Syrup
CAS# 8029-43-4 -- --- R to 185 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
C6H12O6
Cottonseed Oil
-- R to 120 L to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 8001-29-4
Creosote -- --- N R to 73 N R to 140 --- --- R to 140 --- --- ---
Cresol
CAS# 95-48-7 90% N N R to 73 N R to 73 N R to 68 R to 73 --- --- ---
CH3 C6 H4 OH
Cresylic Acid
50% --- N --- R to 140 L to 73 N --- L to 73 --- --- ---
CAS# 106-44-5
Crotonaldehyde -- --- N L to 73 N --- --- --- --- --- --- ---
CAS# 123-73-9 Liquid --- --- --- --- --- --- R to 104 -- --- --- ---
CH3 CH=CHCHO
Crude Oil
-- --- L to 180 R to 140 R to 140 L to 120 L to 73 R to 212 L to 120 R to 140 --- ---
CAS# 8002-05-9
Cupric Fluoride
See Copper Fluoride Dihydrate
Cupric Sulfate
CAS# 7758-99-8 Saturated R to 100 R to 180 R to 73 R to 140 R to 140 --- --- --- --- --- ---
CuSO4 • 5H2 O
Cuprous Chloride
CAS# 7758-89-6 Saturated R to 70 R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
CuCl

24
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Cyclohexane
CAS# 110-82-7 -- R to 73 R to 73 N N N --- R to 248 N L to 140 N ---
C6 H12
Cyclohexanol
CAS# 108-93-0 -- L to 120 L to 73 R to 140 N R to 73 L to 73 R to 104 R to 73 --- --- ---
C6 H11 OH
Cyclohexanone
CAS# 108-94-1 Liquid N N R to 73 N R to 120 N N R to 73 L to 140 --- ---
C6 H10 O
Detergents (Heavy Duty) -- --- L to 180 R to 180 R to 140 R to 140 --- --- R to 140 --- --- ---
Dextrin (Starch Gum)
Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 9004-53-9
Dextrose
CAS# 50-99-7 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
C6H12O6
Diacetone Alcohol
CAS# 123-42-2 -- --- N R to 120 N --- --- --- --- L to 140 N N
CH3 COCH2 C(CH3 )2 OH
Dibutoxyethyl Phthalate
CAS# 117-83-9 -- --- N --- N --- --- --- --- --- --- ---
C20H30O6
n-Dibutyl Ether
CAS# 142-96-1 -- --- N --- --- R to 73 --- --- R to 73 --- --- ---
C4 H9 OC4 H9
Dibutyl Phthalate
CAS# 84-74-2 -- N N R to 73 N R to 73 --- --- R to 73 --- N ---
C6 H4 (COOC4 H9 )2
Dibutyl Sebacate
CAS# 109-43-3 -- --- N R to 73 R to 73 R to 73 --- --- R to 73 --- --- ---
C4 H9 OCO(CH2)8OCOC4 H9

25
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Dichloroacetic Acid
CAS# 79-43-6 50% --- N --- --- --- --- R to 176 --- --- --- ---
CHCl2COOH
Dichlorobenzene -- N N L to 73 N L to 120 --- --- L to 120 --- N ---
CAS# 25321-22-6 Liquid --- --- --- --- --- --- R to 140 --- --- --- ---
C6 H4 Cl2
Dichloroethylene -- --- N L to 73 N L to 120 --- --- L to 120 --- --- ---
CAS# 75-35-4 Liquid --- --- --- --- --- --- R to 248 --- --- --- ---
C2 H2Cl 2
Diesel Fuels -- --- L to 180 R to 140 R to 140 R to 73 L to 73 R to 212 R to 73 --- R to 122 R to 122
Diethanolamine Solid --- --- --- --- --- --- N --- --- --- ---
CAS# 111-42-2 20% --- --- --- --- --- --- --- --- --- --- ---
(CH2CH2OH)2NH
Diethylamine
CAS# 109-89-7 -- N N --- N L to 120 N N L to 120 --- --- ---
C4 H10 NH
Diethyl Ether
CAS# 60-29-7 -- N N R to 73 R to 73 L to 140 --- --- L to 140 R to 140 N ---
C4 H10 O
Diglycolic Acid Saturated --- R to 73 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 110-99-6 10% --- --- --- --- --- --- R to 140 --- --- --- ---
O(CH2 COOH)2
Dimethylamine
CAS# 124-40-3 -- --- N R to 73 R to 140 R to 73 N N R to 73 --- --- ---
(CH3 )2 NH
Dimethylformamide -- N N R to 180 N R to 120 --- --- R to 120 --- --- ---
CAS# 68-12-2 Liquid --- --- --- --- --- --- --- N --- --- ---
HCON(CH3 )2

26
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Dimethylhydrazine
CAS# 57-14-7 -- --- N --- N --- --- --- --- --- --- ---
(CH3 )2 NNH2
Dimethyl Phthalate
CAS# 131-11-3 -- --- N --- --- L to 73 --- --- L to 73 --- --- ---
C6 H4 (COOCH3 )2
Dioctyl Phthalate
CAS# 117-81-7 -- N N L to 73 N L to 73 L to 73 --- L to 73 R to 140 R to 73 ---
C6 H4 (COOC8 H17 )2
Dioxane -- -- N L to 140 N R to 140 --- --- R to 140 --- --- ---
CAS# 123-91-1 Liquid --- --- --- --- --- --- L to 68 --- --- --- ---
C4H8O2
Diphenyl Oxide
CAS# 101-84-8 Saturated --- --- --- --- L to 73 --- --- L to 73 --- --- ---
(C6 H5 )2 O
Disodium Phosphate
CAS# 7558-79-4 -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na2 HPO4
DOWTHERM A ethyl glycol
-- --- --- --- N --- --- --- R to 180 --- --- ---
CAS# 110-80-5
Ethanol 40% --- L to 140 --- --- --- --- R to 68 --- --- --- ---
CAS# 64-17-5 95% --- L to 140 --- --- --- --- R to 122 R to 140 --- --- ---
C2 H5 OH Liquid --- L to 140 --- --- --- --- R to 122 R to 140 --- R to 122 ---
Ether
CAS# 60-29-7 -- N N L to 73 N R to 73 N --- R to 73 --- --- ---
ROR
Ethyl Acetate -- N N L to 140 N R to 73 L to 73 --- R to 73 R to 140 N ---
CAS# 141-78-6 Liquid --- --- --- --- --- --- L to 68 --- --- --- ---
CH3 COOCH2CH3

27
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Ethyl Acetoacetate
CAS# 141-97-9 -- N N --- N --- --- --- --- --- --- ---
CH3 COCH2 COOC2 H5
Ethyl Acrylate
CAS# 140-88-5 -- --- N --- N --- --- --- --- --- --- ---
CH2=CHCOOC2 H5
Ethyl Alcohol-See Ethanol
Ethyl Benzene
CAS# 100-41-4 -- --- N L to 73 N L to 73 --- --- --- --- --- ---
C6 H5 C2 H5
Ethyl Chloride Dry --- N L to 73 N L to 73 --- --- L to 73 --- --- ---
CAS# 75-00-3 Gas --- --- --- --- --- --- R to 212 --- --- --- ---
C2 H5 Cl
Ethyl Chloroacetate
CAS# 105-39-5 -- --- N --- N --- --- --- --- --- --- ---
ClCH2COOC2H5
Ethyl Ether
CAS# 60-29-7 Liquid --- N N N N N R to 122 N --- --- ---
(C2 H5 )2 O
Ethylene Bromide
CAS# 106-93-4 Dry --- N --- N --- N --- --- --- --- ---
BrCH2 CH2 Br
Ethylene Chloride
CAS# 75-01-4
Dry N N L to 73 N L to 140 --- --- L to 140 --- N ---
(Vinyl Chloride)
CH2 CH Cl
Ethylene Chlorohydrin -- --- N R to 73 N --- N --- --- --- --- ---
CAS# 107-07-3 Liquid --- --- --- --- --- --- L to 68 --- --- --- ---
ClCH2 CH2 OH

28
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Ethylene Diamine
CAS# 107-15-3 -- N N R to 73 N R to 140 --- --- R to 140 --- --- ---
NH2 CH2 CH2 NH2
Ethylene Dichloride
CAS# 107-06-2 Dry N N L to 140 N L to 73 R to 140 --- L to 73 --- --- ---
C2 H4 Cl2
Ethylene Glycol Liquid R to 73 L to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 212 --- R to 73 ---
CAS# 107-21-1 50% Solution --- R to 180 --- --- --- --- --- --- --- R to 248 ---
OHCH2CH2 OH
Ethylene Oxide
CAS# 75-21-8 -- --- N L to 73 N R to 73 --- --- R to 73 L to 140 --- ---
CH2 CH2 O
2-Ethylhexanol
CAS# 104-76-7 -- --- --- --- --- R to 73 --- --- R to 73 --- --- ---
CH3 (CH2 )3 CHC2 H5 CH2OH
Fatty Acids
-- R to 160 R to 73 R to 120 R to 140 R to 120 R to 150 --- R to 120 R to 194 --- ---
R-COOH
Ferric Chloride (Aqueous)
CAS# 10025-77-1 Saturated R to 120 R to 180 R to 140 R to 140 R to 140 R to 150 R to 212 R to 140 --- --- ---
FeCl3
Ferric Hydroxide
CAS# 1309-33-7 Saturated R to 160 R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
Fe(OH)3
Ferric Nitrate
CAS# 10421-48-4 Saturated R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Fe(NO3 )3
Ferric Sulfate -- R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 10028-22-5 Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
Fe2 (SO4 )3

29
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Ferrous Chloride
CAS# 7758-94-3 Saturated R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
FeCl2
Ferrous Hydroxide
CAS# 18624-44-7 Saturated R to 160 R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
Fe(OH)2
Ferrous Nitrate
-- R to 160 R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
Fe(NO3 )2
Ferrous Sulfate -- R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7720-78-7 Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
FeSO4
Fish Oil
--- --- L to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 8016-13-5
Fluoroboric Acid --- R to 73 R to 73 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 16872-11-0 Solid --- --- --- --- --- --- R to 104 --- --- --- ---
HBF4
Fluorine Gas (Dry)
CAS# 7782-41-4 100% --- L to 73 N R to 73 L to 73 L to 73 --- L to 73 N --- ---
F2
Fluorine Gas (Wet)
CAS# 7782-41-4 -- N L to 73 N R to 73 N N --- N N --- ---
F2
Fluorosilicic Acid 30% --- R to 180 R to 140 R to 140 R to 140 --- R to 212 R to 140 --- --- ---
CAS# 16961-83-4 40% --- R to 180 --- --- --- --- R to 140 --- --- --- ---
H2 SiF6 50% --- R to 180 R to 73 R to 140 R to 140 R to 140 R to 212 -- --- --- ---
Saturated --- R to 180 --- --- --- --- R to 212 --- --- --- ---
Formaldehyde Dilute R to 160 R to 73 R to 140 R to 140 R to 140 R to 140 R to 176 --- L to 104 --- ---
CAS# 50-00-0 35% R to 160 N R to 140 R to 140 R to 140 R to 140 --- R to 140 --- R to 100 ---
HCHO 37% R to 160 N R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
50% --- N --- R to 140 R to 140 R to 140 --- R to 140 --- --- ---

30
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Formic Acid 10% --- R to 180 --- --- --- --- R to 212 R to 140 N --- ---
CAS# 64-18-6 40% --- --- --- --- --- --- R to 212 R to 140 --- --- ---
HCOOH 50% --- --- --- --- --- --- R to 176 R to 140 --- --- ---
85% --- --- --- --- --- --- R to 212 --- --- R to 122 ---
100% N L to 73 R to 140 R to 73 R to 140 R to 150 --- R to 140 --- --- ---
Freon 11
CAS# 75-69-4 100% N N N R to 140 R to 73 --- --- R to 73 --- --- ---
CCl3F
Freon 12 100% --- N R to 73 R to 140 R to 73 --- --- R to 73 R to 68 R to 73 ---
CAS# 75-71-8 Work. Sol. --- N --- --- --- --- R to 212 R to 68 --- --- ---
CCl2F2
Freon 21
CAS# 75-43-4 100% --- N N N L to 120 --- --- L to 120 --- --- ---
CHCl2F
Freon 22
CAS# 75-45-6 100% --- N R to 73 N L to 120 --- --- L to 120 R to 68 N ---
CHClF2
Freon 113
CAS# 76-13-1 100% --- N N R to 140 R to 73 --- --- R to 73 --- --- ---
C2Cl2F3
Freon 114
CAS# 76-14-2 100% --- N N R to 140 R to 73 --- --- R to 73 --- --- ---
C2Cl2F4
Fructose
CAS# 57-48-7 Saturated R to 73 R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
C6 H12 O6
Fruit Juice Work. Sol. --- --- --- --- --- --- R to 212 --- R to 104 --- ---

31
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Furfural
CAS# 98-01-1 100% N N N N L to 140 --- --- L to 140 L to 140 --- ---
C4 H3 OCHO
Gallic Acid
CAS# 149-91-7 -- --- R to 180 --- R to 140 R to 73 --- --- R to 73 --- --- ---
C6 H2 (OH)3 CO2 H • H2 O
Gasoline, Leaded 3 -- N N N R to 140 R to 73 N --- R to 73 --- --- ---
3
Gasoline, Unleaded -- N N N R to 140 R to 73 N --- R to 73 --- --- R to 122
3
Gasoline (Fuel)
-- --- --- --- --- --- --- R to 212 --- R to 160 --- R to 122
CAS# 8006-61-9
Gasohol 3 -- N N N R to 140 R to 73 N --- R to 73 --- --- R to 122
3
Gasoline, Sour -- N N N R to 140 L to 73 N --- L to 73 --- --- ---
Gelatin
-- --- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 9000-70-8
Glucose -- R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 50-99-7 10% --- --- --- --- --- --- R to 248 --- --- --- ---
C6 H12 O6 • H2 O
Glycerine -- R to 140 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- R to 73 ---
CAS# 56-81-5 Liquid --- --- --- --- --- --- R to 248 --- --- --- ---
C3 H5 (OH)3
Glycolic Acid Saturated --- N R to 73 R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 79-14-1 10% --- --- --- --- --- --- R to 212 --- --- --- ---
OHCH2 COOH 30% --- --- --- --- --- --- R to 140 --- --- --- ---
65% --- --- --- --- --- --- R to 212 --- --- --- ---
Glyoxal
CAS# 107-22-2 -- --- --- --- --- R to 140 --- --- R to 140 --- --- ---
OCHCHO
Grape Sugar
-- --- R to 180 --- R to 140 --- --- --- --- --- --- ---
CAS# 50-99-7
Grapefruit Juice Work. Sol. --- --- --- --- --- --- R to 122 --- --- --- ---

32
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Grease -- --- --- --- --- --- --- --- --- R to 194 --- ---
Green Liquor -- R to 160 R to 180 --- R to 140 --- R to 140 --- --- --- --- ---
n-Heptane
CAS# 142-82-5 Liquid R to 73 R to 73 N R to 140 R to 73 N R to 212 R to 73 --- N ---
C7 H16
n-Hexane
CAS# 110-54-3 Liquid L R to 73 R to 73 R to 73 --- --- R to 176 --- --- R to 73 ---
C6 H14
Hexanol, Tertiary Type I
CAS# 25917-35-5 -- --- L to 180 --- R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CH3 (CH2 )4 CH2 OH
Hydraulic Oil (Petroleum) -- --- --- --- R to 73 R to 73 --- --- R to 73 --- --- ---
Hydrazine
CAS# 302-01-2 -- --- N R to 73 N --- --- --- --- --- --- ---
H2 NNH2
Hydrobromic Acid 20% R to 73 R to 73 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 10035-10-6 50% N --- R to 120 --- R to 140 --- --- R to 140 --- --- ---
HBr 66% --- --- --- --- --- --- R to 212 --- --- --- ---
Hydrochloric Acid 10% L to 120 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 212 L to 104 ---
CAS# 7647-01-0 20% --- --- --- --- --- --- R to 212 R to 212 --- --- R to 212
HCl 30% L to 73 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- R to 140 R to 122
Conc. --- --- --- --- --- --- --- R to 140 --- ---
Hydrocyanic Acid -- R to 160 R to 73 R to 73 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 74-90-8 Saturated --- --- --- --- --- --- R to 248 --- --- --- ---
HCN 10% --- --- --- --- --- --- R to 248 --- --- --- ---

33
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Hydrofluoric Acid Dilute R to 73 R to 180 R to 180 R to 73 R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 7664-39-3 30% N L to 180 R to 140 R to 73 R to 140 R to 140 --- R to 140 --- --- ---
HF 50% N N R to 73 R to 73 R to 120 R to 140 R to 212 R to 120 --- --- ---
60% --- --- --- --- R to 140 --- R to 140 R to 140 --- --- ---
70% --- --- --- --- --- --- R to 212 --- --- --- ---
100% N N L to 73 N R to 120 --- --- R to 120 --- --- ---
Gas --- --- --- --- --- --- R to 104 --- --- --- ---
Hydrogen Gas --- R to 73 R to 140 R to 140 R to 140 R to 140 R to 248 R to 140 R to 194 --- ---
CAS# 1333-74-0
H2
Hydrogen Cyanide -- --- --- R to 73 R to 140 --- --- --- --- --- --- ---
CAS# 74-90-8
HCN
Hydrogen Fluoride,
-- --- L R to 73 N --- --- --- --- --- --- ---
Anhydrous
CAS# 7664-39-3
HF
Hydrogen Peroxide 10% --- R to 180 --- --- --- --- R to 212 --- --- --- ---
CAS# 7722-84-1 30% --- R to 180 --- --- --- --- R to 212 --- L to 104 R to 73 R to 73
H2 O2 50% --- R to 120 R to 73 R to 140 R to 140 N R to 212 R to 140 --- --- ---
90% --- --- L to 73 R to 140 R to 73 N --- R to 73 --- R to 73 ---
Hydrogen Phosphide (Type I) -- --- R to 73 --- R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS # 7803-51-2
PH3
Hydrogen Sulfide Dry --- R to 180 R to 150 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
CAS# 7783-06-4 Wet --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
H2 S

34
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Hydrogen Sulfite 10% --- --- --- --- R to 140 --- R to 248 R to 140 --- --- ---
CAS# 15181-46-1
HO3S
Hydroquinone Saturated --- R to 73 --- R to 140 R to 140 R to 140 --- --- R to 140 --- ---
CAS# 123-31-9
C6 H4 (OH)2
Hydroxylamine Sulfate -- --- --- --- R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 10039-54-0
(NH2 OH)oH2 SO4
Hypochlorous Acid 10% R to 73 L to 180 R to 73 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7790-92-3 70% --- --- --- --- --- --- R to 212 --- --- --- ---
HOCl
Inks -- --- --- R to 140 --- R to 140 --- --- R to 140 --- --- ---
Iodine 10% N R to 73 R to 73 N L to 120 N R to 176 L to 120 --- --- ---
CAS# 7553-56-2
I2
IRM 901 Oil (ASTM #1) -- --- 180 L to 140 R to 140 R to 73 R to 140 R to 248 R to 73 --- --- ---
IRM 902 Oil (ASTM #2) -- --- 180 L to 140 R to 140 R to 73 R to 140 --- R to 73 --- --- ---
IRM 903 Oil (ASTM #3) -- --- 180 L to 140 R to 140 R to 73 R to 140 --- R to 73 --- --- ---
Isobutyl Alcohol
CAS# 78-83-1 -- L to 73 L to 73 R to 73 --- R to 140 --- --- R to 140 --- --- ---
(CH3 )2 CHCH2 OH
Isooctane
CAS# 540-84-1 Liquid --- --- L to 73 --- R to 73 --- R to 212 R to 73 --- --- ---
(CH3 )3 CCH2 CH(CH3)2
Isopropyl Acetate
CAS# 108-21-4 -- N N --- --- R to 73 --- --- R to 73 --- --- ---
CH3 COOCH(CH3 )2

35
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Isopropyl Alcohol
CAS# 67-63-0 -- --- L to 180 R to 212 R to 140 R to 140 R to 140 L to 212 R to 140 --- --- ---
(CH3 )2 CHOH
Isopropyl Ether
CAS# 108-20-3 -- --- N L to 73 N R to 73 --- --- R to 73 --- --- ---
(CH3 )2 CHOCH(CH3)2
JP-4 Fuel 3 -- --- L to 73 L to 73 R to 140 R to 73 --- --- R to 73 --- R to 73 ---
3
JP-5 Fuel -- --- L to 73 L to 73 R to 140 R to 73 --- --- R to 73 --- --- ---
3
Kerosene
-- R to 73 N L to 140 R to 140 L to 140 L to 73 --- L to 140 --- --- ---
CAS# 8008-20-6
Ketchup -- --- R to 180 --- R to 73 --- --- --- --- --- R to 72 ---
Ketones -- N N L to 73 N R to 73 --- --- R to 73 --- --- ---
Kraft Liquors -- R to 73 R to 180 --- R to 140 R to 120 R to 140 --- R to 120 --- --- ---
Lactic Acid 10% --- --- --- --- --- --- R to 140 --- --- --- ---
CAS# 50-21-5 25% R to 73 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CH3 CHOHCOOH 80% N L to 180 R to 140 R to 73 R to 140 --- --- R to 140 --- --- ---
Liquid --- --- --- --- --- --- R to 212 --- R to 194 --- ---
Lard Oil -- --- L to 180 --- R to 140 L to 120 R to 73 --- L to 120 --- --- ---
Latex -- --- --- R to 140 --- R to 140 --- --- R to 140 --- --- ---
Lauric Acid
CAS# 143-07-7 -- --- L to 180 R to 140 R to 140 R to 120 --- --- R to 120 --- --- ---
CH3 (CH2 )10 COOH
Lauryl Chloride (Type I)
CAS# 112-52-7 -- --- N --- R to 140 R to 120 R to 73 R to 248 R to 120 --- --- ---
CH3(CH2)10CH2Cl
Lead Acetate (trihydrate)
CAS# 6080-56-4 Saturated --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Pb(C H3 COO )2 o3H2 O

36
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Lead Chloride
CAS# 7758-95-4 -- --- R to 180 R to 140 R to 140 R to 120 --- --- R to 120 --- --- ---
PbCl2
Lead Nitrate
CAS# 10099-74-8 Saturated --- R to 180 R to 140 R to 140 R to 120 --- --- R to 120 --- --- ---
Pb(NO3 )2
Lead Sulfate
CAS# 7446-14-2 -- --- R to 180 R to 140 R to 140 R to 120 --- --- R to 120 --- --- ---
PbSO4
Lead Tetraethyl
CAS# 78-00-2 -- --- --- --- --- --- --- R to 212 --- --- --- ---
C8H20Pb
Lemon Oil
-- --- N L to 73 --- --- --- --- --- --- --- ---
CAS# 8008-56-8
Lemon Juice -- --- --- --- --- L to 140 --- --- L to 140 --- R to 122 ---
Ligroin (Petroleum Ether)
-- --- --- R to 140 --- --- --- R to 212 --- --- --- ---
CAS# 8032-32-4
Lime Slurry -- --- --- --- --- R to 140 --- --- R to 140 --- --- ---
Lime Sulfur
-- --- R to 73 R to 73 R to 73 R to 120 R to 140 --- R to 120 --- --- ---
CAS# 1344-81-6
Linoleic Acid
CAS# 60-33-3
-- --- L to 180 R to 180 R to 140 --- R to 73 --- --- --- --- ---
CH3 (CH2)4
(CH=CHCH2)2(CH2)6 COOH
Linoleic Oil (Type I) -- --- --- --- R to 140 --- R to 73 --- --- --- --- ---
Linseed Oil
-- 73 L to 180 R to 140 R to 140 R to 73 R to 73 R to 248 R to 73 R to 194 --- ---
CAS# 8001-26-1
Liqueurs -- --- --- R to 140 R to 140 R to 120 R to 140 --- R to 120 --- --- ---

37
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Lithium Bromide -- --- --- R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 7550-35-8 65% --- R to 180 --- --- --- --- --- --- --- R to 212 R to 212
LiBr
Lithium Chloride
CAS# 7447-41-8 -- --- R to 180 R to 140 R to 140 R to 120 --- --- R to 120 --- --- ---
LiCl
Lithium Hydroxide
CAS# 1310-65-2 -- --- R to 73 R to 140 --- R to 120 --- --- R to 120 --- --- ---
LiOH
Magnesium Carbonate
CAS# 546-93-0 -- R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
MgCO3
Magnesium Chloride Saturated R to 120 R to 180 R to 140 R to 140 R to 140 R to 140 R to 140 R to 140 --- --- ---
CAS# 7786-30-3 50% --- --- --- --- --- --- R to 212 ---- R to 194 --- ---
MgCl2
Magnesium Citrate
CAS# 6150-80-7 -- --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
MgC6 H8 O7 o5H2 O
Magnesium Hydroxide
CAS# 1309-42-8 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Mg(OH)2
Magnesium Nitrate
CAS# 10377-60-3 -- R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
Mg(NO3)2 o2H2 O
Magnesium Oxide
CAS# 1309-48-4 -- R to 160 R to 180 --- --- --- --- --- --- --- --- ---
MgO
Magnesium Sulfate
CAS# 7487-88-9 -- R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
MgSO4 o7H2 O

38
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Maleic Acid Saturated R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 R to 140 R to 140 --- --- ---
CAS# 110-16-7 50% --- --- --- --- --- --- R to 212 --- --- --- ---
HOOCCH=CHCOOH
Malic Acid
CAS# 6915-15-7 -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
COOHCH2 CH(OH)COOH
Manganese Sulfate
CAS# 7785-87-7 -- --- R to 180 R to 180 R to 140 R to 140 --- --- R to 140 --- --- ---
MnSO4 • 4H2 O
Margarine Work Sol. --- --- --- --- --- --- R to 248 --- --- --- ---
Mercuric Chloride -- --- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7487-94-7 Saturated -- --- --- --- --- --- R to 212 --- --- --- ---
HgCl2
Mercuric Cyanide
CAS# 592-04-1 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Hg(CN)2
Mercuric Sulfate
CAS# 7783-35-9 Saturated --- R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
HgSO4
Mercurous Nitrate
10% --- --- --- --- --- --- R to 212 --- --- --- ---
(Dihydrate)
CAS# 14836-60-3 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
HgNO3 • 2H2 O
Mercury
CAS# 7439-97-6 Liquid --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 248 R to 140 R to 194 --- ---
Hg
Methane
CAS# 74-82-8 -- N R to 73 R to 73 R to 140 R to 140 --- --- R to 140 R to 140 --- ---
CH4

39
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Methanol (Methyl Alcohol) 5% --- R to 180 --- --- --- --- R to 140 --- --- --- ---
CAS# 67-56-1 Liquid --- N R to 180 R to 140 R to 140 R to 140 L to 176 R to 140 --- R to 73 ---
CH3 OH
Methoxyethyl Oleate
CAS# 111-10-4 -- --- N --- R to 73 --- --- --- --- --- --- ---
CH3 OCH2 CH2 OOCC17H33
Methyl Acetate
CAS# 79-20-9 -- N N R to 140 N L to 120 --- --- L to 120 --- --- ---
CH3 CO2 CH3
Methyl Acrylate
CAS# 96-33-3 Tech Pure --- N --- --- R to 140 --- --- R to 140 --- --- ---
CH2 =CHCOOCH3
Methylamine
CAS# 74-89-5 -- --- N N N --- --- --- --- --- --- ---
CH3 NH2
Methyl Bromide
CAS# 74-83-9 -- --- N N N L to 73 --- --- L to 73 R to 68 --- ---
CH3 Br
Methyl Butyl Ketone
CAS# 591-78-6 Liquid --- N --- --- --- --- L to 122 --- --- --- ---
CH3CO(CH2)3CH3
Methyl Cellosolve
CAS# 109-86-4 -- --- N R to 73 N L to 120 --- --- L to 120 --- --- ---
HOCH2 CH2 OCH3
Methyl Chloride
CAS# 74-87-3 Dry N N N N L to 120 N --- L to 120 R to 68 --- ---
CH3 Cl
Methyl Chloroform
CAS# 71-55-6 -- N N L to 73 N L to 120 --- --- L to 120 --- --- ---
CH3CCl3

40
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Methyl Ethyl Ketone (MEK)
CAS# 78-93-3 100% N N R to 73 N N R to 73 L to 68 R to 73 L to 140 N ---
CH3 COC2 H5
Methyl Isobutyl Carbinol
CAS# 108-11-2 -- --- N --- N --- --- --- --- --- --- ---
(CH3 )2 CHCH2 CH(CH3 )OH
Methyl Isobutyl Ketone
CAS# 108-10-1 -- N N R to 73 N R to 73 --- --- R to 73 --- --- ---
(CH3 )2 CHCH2 COCH3
Methyl Isopropyl Ketone
CAS# 563-80-4 -- --- N --- N R to 73 --- --- R to 73 --- --- ---
CH3 COCH(CH3 )2
Methyl Methacrylate
CAS# 80-62-6 -- --- N --- R to 73 R to 140 --- R to 68 R to 140 --- N ---
CH2=C(CH3 )COOCH3
Methyl Sulfate
CAS# 77-78-1 -- --- R to 73 L to 73 R to 73 R to 140 --- --- --- R to 68 --- ---
(CH3 )2 SO4
Methylene Bromide
CAS# 74-95-3 -- --- N N N L to 120 --- --- L to 120 --- --- ---
CH2 Br2
Methylene Chloride
CAS# 75-09-2 100% --- N N N N R to 73 L to 104 N --- N ---
CH2 Cl2
Methylene Chlorobromide
CAS# 74-97-5 -- --- N -- N --- --- --- --- --- --- ---
CH2 ClBr

41
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Methylene Iodide
CAS# 75-11-6 -- --- N N N L to 120 --- --- L to 120 --- --- ---
CH2 l2
Methylsulfuric Acid
CAS# 75-93-4 -- --- --- R to 140 R to 140 --- --- --- --- --- --- ---
CH3 HSO4
Milk
-- R to 160 L to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 R to 194 R to 200 ---

Mineral Oil (Paraffin Oil)

-- R to 73 R to 180 L to 140 R to 140 R to 73 L to 73 R to 212 L to 176 --- --- ---
CAS# 8012-95-1

Molasses -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---

Monochloroacetic Acid
CAS# 79-11-8 50% --- N R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
CH2ClCOOH
Monochlorobenzene
CAS# 108-90-7 Tech Pure --- N R to 73 N L to 120 --- --- L to 120 --- --- ---
C6 H5 Cl
Monoethanolamine
CAS# 141-43-5 -- --- N --- N --- --- --- --- --- --- ---
HOCH2 CH2 NH2

Motor Oil -- --- R to 73 L to 140 R to 140 R to 140 --- --- R to 140 --- --- ---

Morpholine
CAS# 110-91-8 -- --- N R to 140 --- R to 140 --- --- R to 140 --- N N
C4 H8 ONH

Mustard, Aqueous Work. Sol. --- --- --- --- --- --- R to 248 --- --- R to 72 ---

Naphtha
-- --- R to 73 R to 73 R to 140 R to 73 R to 73 R to 122 L to 176 R to 140 --- ---
CAS# 8030-30-6

42
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Naphthalene
CAS# 91-20-3 -- --- R to 73 R to 73 N R to 73 R to 73 --- R to 73 R to 194 N ---
C10 H 8
Natural Gas
-- R to 73 --- R to 73 R to 140 R to 140 R to 73 --- R to 140 --- --- ---
CAS# 68410-96-6
Nickel Acetate
CAS# 373-02-4 -- --- R to 180 R to 73 --- R to 140 --- --- R to 140 --- --- ---
Ni(OOCCH3 )2 • 4H2 O
Nickel Chloride
CAS# 7718-54-9 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NiCl2
Nickel Nitrate
CAS# 13138-45-9 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
Ni(NO3 )2 o6H2 O
Nickel Sulfate
CAS# 7786-81-4 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- R to 140 ---
NiSO4
Nicotine
CAS# 54-11-5 -- --- --- --- R to 140 R to 140 R to 140 --- R to 140 --- --- ---
C10 H14 N2
Nicotinic Acid
CAS# 59-67-6 -- --- --- --- R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
C5H4 NCOOH

43
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Nitric Acid 5% --- --- --- --- --- --- R to 176 L to 140 N R to 210 ---
CAS# 7697-37-2 10% L to 73 R to 180 R to 180 R to 140 R to 73 L to 73 R to 212 L to 140 --- --- ---
HNO3 20% --- --- --- --- --- --- R to 212 L to 140 --- --- ---
30% N R to 130 R to 140 R to 140 R to 73 N R to 212 L to 140 --- --- ---
40% N R to 120 R to 73 R to 140 R to 73 N L to 248 L to 140 --- --- ---
50% N R to 110 N R to 100 L to 73 N --- L to 140 --- --- ---
65% --- --- --- --- --- --- L to 248 --- --- --- ---
70% N R to 100 N R to 73 L to 73 N --- L to 73 --- --- ---
85% --- --- --- --- --- --- N --- --- --- ---
100% N N N N N N --- N --- --- ---
Nitrobenzene
CAS# 98-95-3 100% N N L to 140 N N --- R to 122 N --- --- ---
C 6H5 NO2
Nitroglycerine -- --- N --- N R to 73 --- --- R to 73 --- --- ---
CAS# 55-63-0 1% --- N --- --- --- --- --- --- --- R to 73 R to 73
CH2 NO3 CHNO3 CH2 NO3
Nitroglycol
CAS#628-96-6 -- --- --- --- N --- --- --- --- --- --- ---
NO3 (CH2)2NO3
Nitrous Acid
CAS# 7782-77-6 10% --- R to 73 L to 73 R to 140 R to 73 --- --- R to 73 --- --- ---
HNO2
Nitrous Oxide
CAS# 10024-97-2 -- --- R to 73 R to 73 R to 73 R to 73 --- --- R to 73 --- R to 68 ---
N2 O
n-Octane
CAS# 111-65-9 -- --- R to 73 --- --- --- --- --- --- --- R to 73 ---
C8 H18

44
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Oleic Acid
CAS# 112-80-1
-- R to 160 L to 180 R to 73 R to 140 L to 140 R to 150 R to 248 L to 140 R to 140 R to 73 ---
CH3 (CH2 )7 CH=CH(CH2 )7
COOH
Oleum
CAS# 57-06-7 -- N N N N N N N N --- --- ---
x H2 SO4 oySO3
Olive Oil
-- R to 160 L to 180 R to 73 R to 140 R to 140 --- R to 248 R to 140 --- --- ---
CAS# 8001-25-0

Oxalic Acid 50% R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 144-62-7 10% --- --- --- --- --- --- R to 140 --- R to 140 --- ---
HOOCCOOHo2H2O Saturated --- --- --- --- --- --- R to 122 --- --- --- ---
Oxygen Gas
CAS# 7782-44-7 -- R to 160 R to 180 N R to 140 R to 140 --- R to 212 R to 140 R to 140 --- ---
O2
Ozone
CAS# 10028-15-6 -- --- R to 180 L to 73 R to 140 L to 120 --- --- L to 120 L to 68 --- ---
O3
Palm Oil
-- --- --- R to 73 --- R to 140 --- --- R to 140 --- --- ---
CAS# 8002-75-3
Palmitic Acid 10% R to 73 R to 73 R to 180 R to 140 R to 120 R to 150 --- R to 120 --- --- ---
CAS# 57-10-3 70% --- R to 73 R to 180 R to 73 R to 120 --- --- R to 120 --- --- ---
CH3 (CH2 )14 COOH
Paraffin
CAS# 8002-74-2 -- R to 73 R to 180 R to 140 R to 140 L to 140 --- R to 212 L to 140 --- --- ---
C36 H74

45
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Peanut Oil
-- --- L to 180 R to 140 --- --- --- R to 248 --- --- --- ---
CAS# 8002-03-7
n-Pentane
CAS# 109-66-0 -- N L to 180 N L to 140 L to 120 --- --- L to 120 --- --- ---
CH3 (CH2 )3 CH3
Peracetic Acid
CAS# 79-21-0 40% N N R to 73 R to 73 --- --- --- --- --- --- ---
CH3 COOOH
Perchloric Acid (Type I) 10% --- R to 73 --- --- --- --- R to 212 --- --- --- ---
CAS# 7601-90-3 15% --- --- R to 140 R to 73 R to 140 L to 73 --- R to 140 --- --- ---
HClO4 70% R to 73 --- L to 73 R to 73 R to 73 N R to 212 R to 73 --- --- ---
Perchloroethylene
CAS# 127-18-4
-- N N L to 73 L to 140 L to 120 --- L to 212 L to 120 L to 68 N ---
(tetrachloroethylene)
Cl2 C=CCl2
Perphosphate
-- --- --- R to 140 R to 73 --- --- --- --- --- --- ---
CAS# 7758-23-8
Petroleum Ether
-- --- --- R to 140 --- --- --- R to 212 --- --- --- ---
CAS# 8032-32-4
Phenol -- N R to 73 R to 73 R to 73 R to 140 R to 73 --- R to 73 N --- ---
CAS# 108-95-2 5% --- --- --- --- --- --- --- L to 73 --- L to 140 ---
C6 H5 OH 50% --- --- --- --- --- --- R to 176 --- --- --- ---
90% --- --- --- --- N --- --- N --- --- ---
Solid --- --- --- --- --- --- L to 122 --- --- --- ---
Phenylhydrazine
CAS# 100-63-0 -- --- N N N N --- R to 104 N --- --- ---
C6H5 NHNH2

46
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Phenylhydrazine
Hydrochloride
CAS# 59-88-1 10% --- --- --- --- --- --- R to 140 N --- --- ---

C6H5NHNH2·HCl
Phosphine
CAS# 7803-51-2 Gas --- --- --- --- --- --- R to 104 --- --- --- ---
PH3
Phosphoric Acid 10% --- R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7664-38-2 50% R to 73 R to 180 R to 212 R to 140 R to 140 R to 73 R to 212 R to 140 L to 104 --- ---
H3 PO4 85% --- R to 180 R to 212 R to 140 R to 73 --- --- R to 73 --- --- ---
98% --- --- --- --- --- --- R to 212 --- --- --- ---
Phosphoric Anhydride
CAS# 1314-56-3 -- --- R to 73 R to 73 R to 73 --- --- --- --- --- --- ---
P2 O5
Phosphorous (Red)
CAS# 7723-14-0 -- --- --- --- R to 73 R to 140 --- --- R to 140 --- R to 120 ---
P
Phosphorous (White/Yellow)
CAS# 12185-10-3 -- -- --- --- R to 73 R to 140 --- --- R to 140 --- R to 120 ---
P4
Phosphorus Oxychloride
CAS# 10025-87-3 Liquid --- --- --- --- --- --- R to 68 --- --- --- ---
POCl3
Phosphorus Pentoxide
CAS# 1314-56-3 -- --- R to 73 R to 73 R to 73 R to 140 --- --- R to 140 --- --- ---
P2 O5
Phosphorus Trichloride
CAS# 7719-12-2 -- -- N R to 73 N R to 120 L to 73 L to 122 R to 120 --- --- ---
PCl3

47
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Phthalic Acid -- --- N R to 140 L to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 88-99-3 Susp. --- N --- --- --- --- R to 212 --- --- --- ---
C6 H4 (COOH)2
Picric Acid 10% N N R to 73 N R to 73 R to 73 R to 212 R to 73 L to 68 --- ---
CAS# 88-89-1 Saturated. --- --- --- --- --- --- R to 212 --- --- --- ---
C6 H2 (NO2 )3 OH
Pine Oil
CAS# 8002-09-3 -- --- N R to 140 --- R to 73 --- --- R to 73 --- --- ---

Plating Solutions (Brass) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Cadmium) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Chrome) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Copper) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Gold) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Lead) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Nickel) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Rhodium) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---

Plating Solutions (Silver) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---
Plating Solutions (Tin) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---
Plating Solutions (Zinc) -- --- R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---
Potash (Aq)-See Potassium
Hydroxide
CAS# 1310-58-3
KOH

48
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Potassium Alum
CAS# 10043-67-1 -- --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
AlK (SO4 )2 o12H2 O

Potassium Aluminum Sulfate

-- --- R to 180 R to 180 R to 140 --- L to 73 --- --- --- --- ---
CAS# 10043-67-1
AlK (SO4 )2 o12H2 O
Potassium Amyl Xanthate
CAS# 2720-73-2 -- --- --- --- R to 73 --- --- --- --- --- --- ---
CH3(CH2)4OC(=S)-S.K
Potassium Bicarbonate
CAS# 298-14-6 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
KHCO3
Potassium Bi- chromate Saturated --- R to 180 R to 140 R to 140 --- L to 73 R to 212 --- --- --- ---
CAS# 7778-50-9 40% --- --- --- --- --- --- R to 212 --- --- --- ---
K2 Cr2 O7
Potassium Bisulfate
CAS# 7646-93-7 -- --- R to 180 R to 212 R to 140 R to 140 --- R to 212 R to 140 --- --- ---
KHSO4
Potassium Borate
CAS#12045-78-2 -- -- R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
K2 B4 O7 o4H2 O

Potassium Bromate -- --- R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 7758-01-2 10% --- --- --- --- --- --- --- R to 180 --- --- ---
KBrO3
Potassium Bromide
CAS# 7758-02-3 -- --- R to 180 R to 212 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
KBr

49
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Potassium Carbonate
CAS# 584-08-7 -- R to 73 R to 180 R to 180 R to 140 R to 140 R to 140 N R to 140 --- --- ---
K2 CO3
Potassium Chlorate
(Aqueous)
CAS# 3811-04-9 -- R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 N R to 140 --- --- ---
KClO3
Potassium Chloride
CAS# 7747-40-7 -- R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
KCl
Potassium Chromate
CAS# 7789-00-6 -- --- R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
K2 CrO4
Potassium Cyanide
CAS# 151-50-8 -- --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
KCN
Potassium Dichromate
CAS# 7778-50-9 Saturated -- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
K2 Cr2 O7
Potassium Ethyl Xanthate
CAS# 140-89-6 -- --- --- --- R to 73 --- --- --- --- --- --- ---
KS2 COC2 H5
Potassium Ferricyanide
CAS# 13746-66-2 -- --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
K3 Fe(CN)6
Potassium Ferrocyanide
CAS# 13943-58-3 -- --- R to 180 R to 180 R to 140 R to 140 --- R to 248 R to 140 --- --- ---
K4 Fe(CN)6 o3H2 O
Potassium Fluoride
CAS# 7789-23-3 -- --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
KF

50
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Potassium Hydroxide 10% --- --- --- --- --- --- R to 176 --- --- --- ---
CAS# 1310-58-3 20% --- --- --- --- --- --- R to 176 --- --- --- ---
KOH 25% R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
35% --- --- --- --- --- --- --- --- --- R to 176 ---
50% --- R to 180 --- --- --- --- R to 176 --- L to 104 --- ---
Potassium Hydrogen Sulfite 10% --- --- --- --- --- --- R to 140 --- --- --- ---
CAS# 10117-38-1 Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
KHSO3
Potassium Hypochlorite -- R to 160 R to 180 --- R to 140 R to 120 --- --- R to 120 --- --- ---
CAS# 7778-66-7 3% --- --- --- --- --- --- R to 212 --- --- --- ---
KClO
Potassium Iodide
CAS# 7681-11-0 -- --- R to 180 R to 73 R to 73 R to 140 --- R to 212 R to 140 --- --- ---
KI
Potassium Nitrate -- R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 L to 104 --- ---
CAS# 7757-79-1 50% --- --- --- --- --- --- R to 212 --- --- --- ---
KNO3
Potassium Orthophosphate
CAS# 7778-77-0 Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
H2KPO4
Potassium Perborate
CAS# 13769-41-0 -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
KBHO3
Potassium Perchlorate
CAS# 7778-74-7 -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
KClO4

51
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Potassium Permanganate 10% --- R to 180 R to 73 R to 140 R to 140 R to 140 R to 176 R to 140 --- --- ---
CAS# 7722-64-7 20% --- --- --- --- --- --- R to 212 --- --- --- ---
KMnO4 25% --- R to 180 R to 73 R to 73 R to 140 --- --- R to 140 --- --- ---
30% --- --- --- --- --- --- R to 212 --- --- --- ---
Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
Potassium Persulfate
CAS# 7727-21-1 -- --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 176 R to 140 --- --- ---
K2 S2 O8
Potassium Sulfate
CAS# 7778-80-5 -- R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 R to 194 --- ---
K2 SO4
Potassium Sulfide
CAS# 1312-73-8 -- --- R to 180 R to 140 --- R to 140 R to 140 R to 68 R to 140 --- --- ---
K2 S
Potassium Sulfite
CAS# 10117-38-1 -- --- R to 180 R to 140 --- R to 140 --- --- R to 140 --- --- ---
K2 SO3 o2H2 O
Propane
CAS# 74-98-6 -- --- R to 73 R to 73 R to 140 R to 140 R to 73 R to 248 R to 140 R to 140 --- ---
C3 H8
Propargyl Alcohol
CAS# 107-19-7 -- --- L to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
HC≡CCH2 OH
Propionic Acid
CAS# 79-09-4 -- N N R to 140 --- R to 140 --- R to 140 R to 140 --- N L to 104
CH3 CH2 CO2 H
Propyl Alcohol (Type I)
CAS# 71-23-8 -- 73 L to 73 R to 140 R to 140 R to 140 R to 140 R to 122 R to 140 --- --- ---
CH3CH2CH2OH

52
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Propylene Dichloride
CAS# 78-87-5 100% --- N N N N --- --- N --- --- ---
CH3 CHClCH2 Cl
Propylene Oxide
CAS# 75-56-9 -- --- N R to 73 N R to 140 --- --- R to 140 --- --- ---
CH3 CHCH2 O
Pyridine
CAS# 110-86-1 -- --- N L to 140 N R to 73 --- R to 68 R to 73 L to 68 --- ---
N(CH)4 CH
Pyrogallic Acid
CAS# 87-66-1 -- --- --- --- R to 73 -- -- --- --- --- --- ---
C6 H3 (OH)3
Quinone
CAS# 106-51-4 -- --- --- R to 140 --- R to 140 --- --- R to 140 --- --- ---
C6 H4 O2

Rayon Coagulating Bath -- --- R to 180 --- R to 140 R to 140 R to 140 --- R to 140 --- --- ---

Salicylaldehyde
CAS# 90-02-8 -- --- N R to 73 N R to 120 --- --- R to 120 --- --- ---
C6 H4 OHCHO
Salicylic Acid
CAS# 69-72-7 -- --- --- R to 140 R to 140 R to 140 --- R to 212 R to 140 --- --- ---
C6 H4 (OH)(COOH)
Selenic Acid Aq.
CAS# 13410-01-0 -- --- R to 180 --- R to 140 R to 140 R to 140 --- R to 140 --- --- ---
H2 SeO4
Silicic Acid
CAS# 10193-36-9 -- --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
SiO2 onH2 O

53
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Silicone Oil
(Polydimethylsiloxane) -- --- R to 180 R to 212 R to 73 R to 73 --- --- R to 73 --- --- ---
CAS# 63148-62-9
Silver Acetate
CAS# 563-63-3 Saturated --- R to 180 --- --- --- --- R to 212 --- --- --- ---
AgCH3COO
Silver Chloride
CAS# 7783-90-6 -- R to 160 R to 180 R to 140 R to 140 --- --- --- --- --- --- ---
AgCl
Silver Cyanide
CAS# 506-64-9 -- --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
AgCN
Silver Nitrate -- R to 160 R to 180 R to 180 R to 140 R to 140 L to 73 --- R to 140 --- --- ---
CAS# 7761-88-8 50% --- --- --- --- --- --- R to 212 --- --- --- ---
AgNO3
Silver Sulfate
CAS# 10294-26-5 -- R to 160 R to 180 R to 140 R to 140 R to 140 L to 73 --- R to 140 --- --- ---
Ag2 SO4
Sodium Acetate
CAS# 127-09-3 Saturated --- R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CH3 COONa
Sodium Alum
CAS# 10102-71-3 -- --- R to 180 --- R to 140 --- --- --- --- --- --- ---
AlNa(SO4 )2 o12H2 O
Sodium Aluminate 30% --- --- --- --- --- --- --- --- --- R to 165 ---
CAS# 1302-42-7 Saturated --- R to 180 --- R to 140 --- --- --- --- --- --- ---
Na2 Al2 O4
Sodium Benzoate -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 532-32-1 50% --- --- --- --- --- --- R to 212 --- --- --- ---
C6 H5 COONa

54
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Sodium Bicarbonate
CAS# 144-55-8 -- R to 73 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NaHCO3
Sodium Bisulfate -- R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7681-38-1 50% --- --- --- --- --- --- R to 212 --- --- --- ---
NaHSO4
Sodium Bisulfite
CAS# 7631-90-5 -- --- R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
NaHSO3
Sodium Borate (Borax) 1% --- --- --- --- --- --- --- --- --- R to 113 ---
CAS# 1303-96-4 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na2 B4 O7 o10H2 O
Sodium Bromide Saturated R to 120 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7647-15-6 50% --- -- --- --- --- --- R to 248 --- --- --- ---
NaBr
Sodium Carbonate -- R to 73 R to 180 R to 212 R to 140 R to 140 R to 140 N R to 140 R to 140 --- ---
CAS# 497-19-8 1.70% --- --- --- --- --- --- --- --- --- R to 210 ---
Na2 CO3
Sodium Chlorate
CAS# 7775-09-9 Saturated --- R to 180 R to 140 R to 73 R to 140 R to 140 N R to 140 --- --- ---
NaClO3
Sodium Chloride Saturated R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 R to 194 --- ---
CAS# 7647-14-5 10% --- --- --- --- --- --- R to 212 --- --- R to 140 ---
NaCl
Sodium Chlorite
CAS# 7758-19-2 25% --- R to 180 R to 73 N R to 140 --- --- R to 140 --- --- ---
NaClO2
Sodium Chromate
CAS# 7775-11-3 -- R to 120 R to 180 R to 140 --- R to 140 --- R to 176 R to 140 --- --- ---
Na2 CrO4 o4H2 O

55
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Sodium Cyanide
CAS# 143-33-9 -- --- R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NaCN
Sodium Dichromate Saturated --- R to 180 --- R to 140 --- --- --- --- --- --- ---
CAS# 10588-01-9 20% --- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na2 Cr2 O7 o2H2 O 50% --- --- --- --- --- --- R to 212 --- --- --- ---
Sodium Ferricyanide
CAS#14217-21-1 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na3 Fe(CN)6
Sodium Ferrocyanide
CAS# 14434-22-1 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na4 Fe(CN)6
Sodium Fluoride
CAS# 7681-49-4 -- R to 120 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NaF
Sodium Hydrogen Sulfite
CAS# 7631-90-5 50% --- --- --- --- --- --- R to 212 --- --- --- ---
NaHSO3
Sodium Hydroxide (Caustic
5% --- --- --- --- --- --- L to 68 --- --- --- ---
Soda)
CAS# 1310-73-2 15% R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- R to 212
NaOH 30% R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 N R to 140 --- --- ---
50% R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 L to 104 R to 194 ---
70% R to 120 --- R to 212 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Sodium Hypochlorite -- R to 120 R to 180 R to 73 R to 73 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7681-52-9 2% Cl --- --- --- --- --- --- R to 212 --- --- --- ---
NaOClo5H2 O 5% Cl --- R to 180 R to 120 R to 140 L to 140 --- --- L to 140 --- --- ---
12% Cl R to 73 R to 180 R to 120 R to 140 R to 73 R to 140 R to 68 R to 73 --- R to 190 ---

56
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Sodium Iodide
CAS# 7681-82-5 -- --- R to 180 --- R to 140 --- --- --- --- --- --- ---
NaI
Sodium Metaphosphate
CAS# 10361-03-2 -- --- R to 180 R to 120 R to 140 --- --- --- --- --- --- ---
(NaPO3 )n
Sodium Metasilicate
CAS# 6834-92-0 100% --- --- --- --- --- --- --- --- --- R to 212
H2SiO3
Sodium Nitrate
CAS# 7631-99-4 Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NaNO3
Sodium Nitrite
7632-00-0 -- R to 160 R to 180 R to 73 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
NaNO2
Sodium Palmitate
CAS# 408-35-5 5% --- R to 180 R to 140 R to 140 --- --- --- --- --- --- ---
CH3 (CH2 )14COONa
Sodium Perborate
CAS# 7632-04-4 -- R to 120 R to 180 R to 73 R to 140 R to 73 --- --- R to 73 --- --- ---
NaBO3 o4H2 O
Sodium Perchlorate
CAS# 7601-89-0 -- --- R to 180 R to 212 R to 140 R to 140 --- --- R to 140 --- --- ---
NaClO4
Sodium Peroxide
CAS# 1313-60-6 10% --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
Na2 O2
Sodium Phosphate Acid R to 120 R to 180 R to 212 R to 140 R to 140 R to 140 R to 140 R to 140 --- --- ---
CAS# 7601-54-9 Alkaline --- R to 120 R to 180 R to 212 R to 140 R to 140 --- R to 140 --- --- ---
NaH2 PO4 Neutral --- R to 120 R to 180 R to 212 R to 140 R to 140 --- R to 180 --- --- ---

57
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Sodium Silicate -- --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 6834-92-0 10% --- --- --- --- --- --- R to 140 --- --- --- ---
2Na2 OoSiO2 50% --- --- --- --- --- --- R to 212 --- --- --- ---
100% --- --- --- --- --- --- --- --- --- R to 194 ---
Sodium Sulfate Saturated R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 --- --- --- ---
CAS# 7757-82-6 0.10% --- --- --- --- --- --- R to 140 --- --- --- ---
Na2SO4
Sodium Sulfide 30% --- --- --- --- --- --- --- --- --- R to 165 ---
CAS# 1313-82-2 Saturated R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 --- R to 140 L to 104 --- ---
Na2S
Sodium Sulfite
CAS# 7757-83-7 Saturated R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Na2SO3
Sodium Thiosulfate -- --- R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7772-98-7 50% --- --- --- --- --- --- R to 248 --- --- --- ---
Na2S2O3o5H2O
Soybean Oil
-- --- L to 180 R to 73 --- R to 140 --- --- R to 140 --- --- ---
CAS# 8001-22-7
Stannic Chloride
CAS# 7646-78-8 Saturated --- R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
SnCl4
Stannous Chloride 15% R to 120 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 7772-99-8 Saturated --- --- --- --- R to 140 --- --- R to 140 --- --- ---
SNCl2
Starch
-- --- R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 9005-25-8
Soluble Starch
CAS# 9005-84-9 Saturated --- R to 180 --- --- R to 140 --- --- R to 140 --- --- ---
(C6H10O5)n

58
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Stearic Acid
CAS# 57-11-4 -- --- R to 73 R to 73 R to 140 R to 120 R to 150 --- R to 120 L to 194 --- ---
CH3(CH2)16COOH
Stoddard’s Solvent
-- --- N --- N R to 73 R to 140 --- R to 73 --- --- ---
CAS# 8052-41-3
Styrene
CAS# 100-42-5 -- --- N R to 73 --- L to 73 --- --- L to 73 R to 104 --- ---
C6H5CH=CH2
Succinic Acid
CAS# 110-15-6 -- --- R to 180 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
COOH(CH2)2COOH
Sugar
CAS# 50-99-7 Aq. --- R to 180 --- R to 140 R to 140 --- --- R to 140 --- --- ---
C6H12O6
Sulfamic Acid
CAS# 5329-14-6 20% -- N R to 180 N --- --- --- --- --- --- ---
HSO3NH2
Sulfur
CAS# 7404-34-9 -- --- R to 180 R to 212 R to 140 R to 140 R to 140 --- --- R to 104 --- ---
S
Sulfur Chloride
CAS# 10025-67-9 -- --- --- L to 73 --- --- --- --- --- --- --- ---
S2Cl2
Sulfur Dioxide Gas Dry N R to 73 R to 140 R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 7446-09-5 Gas Wet N N R to 140 R to 73 R to 120 R to 73 N R to 120 --- --- ---
SO2
Sulfur Trioxide Gas Dry --- --- --- R to 140 N --- N N L to 68 --- ---
CAS# 7446-11-9 Gas --- N --- R to 73 N --- N --- --- --- ---
SO3

59
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Sulfuric Acid 30% R to 120 R to 180 R to 180 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
CAS# 7664-93-9 50% R to 73 R to 180 R to 140 R to 140 R to 120 L to 73 R to 140 --- --- R to 212
H2SO4 60% L to 73 R to 180 R to 73 R to 140 R to 120 L to 73 R to 248 --- --- --- ---
70% L to 73 R to 180 R to 73 R to 140 R to 120 L to 73 --- --- --- --- ---
80% L to 73 R to 180 R to 73 R to 140 R to 120 N L to 248 --- --- --- ---
90% L to 73 R to 150 R to 73 R to 73 R to 120 N R to 212 --- --- --- ---
93% N R to 140 L to 73 R to 73 L to 73 N --- --- --- --- ---
94% - 98% N R to 130 L to 73 N L to 73 N L to 212 N --- R to 140 R to 140
100% N N N N N N --- N L to 194 --- ---
Sulfurous Acid
CAS# 7782-99-2 -- --- R to 73 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
H2SO3
Tall Oil
-- --- L to 180 R to 180 R to 140 R to 120 --- --- R to 120 --- --- ---
CAS# 8002-26-4
Tannic Acid 10% N R to 180 R to 73 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 1401-55-4 Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
C76H52O46
Tartaric Acid -- R to 160 R to 180 R to 140 R to 140 R to 140 R to 140 R to 248 R to 140 --- --- ---
CAS# 526-83-0 Saturated --- --- --- --- --- --- R to 248 --- R to 194 --- ---
HOOC(CHOH)2COOH
Terpineol
CAS# 8000-41-7 -- --- --- --- L to 140 --- --- --- --- --- --- ---
C10H17OH
Tetrachloroethane
CAS# 79-34-5 -- --- N L to 73 L to 140 L to 120 --- --- L to 120 --- --- ---
CHCl2CHCl2
Tetrachloroethylene
CAS# 127-18-4 -- N N L to 73 L to 140 L to 120 --- L to 212 L to 120 L to 68 --- ---
Cl2C=CCl2

60
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Tetraethyl Lead
CAS# 78-00-2 -- --- R to 73 R to 73 R to 73 --- --- --- --- R to 68 --- ---
Pb(C2H5)4
Tetrahydrofuran
CAS# 109-99-9 -- N N L to 73 N L to 73 L to 73 L to 68 N --- --- ---
C4H8O
Tetralin
CAS# 119-64-2 -- --- N N N N --- --- N --- --- ---
C10H12
Tetra Sodium Pyrophosphate
CAS# 7722-88-5 -- --- R to 180 --- R to 140 --- --- --- --- --- --- ---
Na4P2O7o10H2O
Thionyl Chloride
CAS# 7719-09-7 -- --- N N N N R to 140 N N --- --- ---
SOCl2
Tin (II) Chloride
CAS# 7772-99-8 -- --- R to 180 --- --- --- --- R to 212 --- --- --- ---
SnCl2
Tin (IV) Chloride
CAS# 7646-78-8 -- --- R to 180 --- --- --- --- R to 212 --- --- --- ---
SnCl4
Titanium Tetrachloride
CAS# 7550-45-0 -- --- --- R to 140 L to 73 R to 120 --- --- R to 120 --- --- ---
TiCl4
Toluene (Toluol)
CAS# 108-88-3 -- N N L to 73 N L to 120 N --- L to 120 R to 140 N N
CH3C6H5
Tomato Juice -- --- R to 180 R to 212 R to 140 R to 140 --- --- R to 140 --- --- ---

61
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Tributyl Citrate
CAS# 77-94-1 -- --- N L to 73 R to 73 L to 120 --- --- L to 120 --- --- ---
C18H32O7
Tributyl Phosphate
CAS# 126-73-8 -- --- N L to 140 N R to 73 --- --- R to 73 R to 194 --- ---
(C4H9)3PO4
Trichloroacetic Acid 50% --- N R to 140 R to 140 R to 140 --- R to 104 R to 140 --- --- ---
CAS# 76-03-9 10% --- N --- --- R to 140 --- --- R to 140 --- --- ---
CCl3COOH
Trichlorobenzene
CAS# 12002-48-1 -- --- N --- --- --- --- R to 140 --- --- --- ---
C6H3Cl3
Trichloroethane
CAS# 71-55-6 -- --- N --- --- --- --- --- --- --- N ---
C2H3Cl3
Trichloroethylene
CAS# 79-01-6 -- N N N N L to 120 N R to 176 L to 68 L to 68 N ---
CHCl=CCl2
Triethanolamine
CAS# 102-71-6 -- L to 73 N R to 140 R to 73 R to 73 R to 73 L to 104 R to 73 --- --- ---
(HOCH2CH2)3N
Triethylamine
CAS# 121-44-8 -- --- N N R to 140 R to 73 --- --- R to 73 --- --- ---
(C2H5)3N
Trimethylolpropane
CAS# 77-99-6 -- --- R to 73 R to 140 R to 73 L to 120 --- --- L to 120 --- --- ---
(CH2OH)3C3H5
Trisodium Phosphate
CAS# 10101-89-0 -- R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
Na3PO4 • 12H2O

62
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Turpentine
-- N N N R to 140 L to 120 L to 73 --- L to 120 R to 140 --- ---
CAS# 8006-64-2
Urea -- --- N R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---
CAS# 57-13-6 10% --- --- --- --- --- --- R to 212 --- --- --- ---
CO(NH2)2 Saturated --- --- --- --- --- --- R to 176 --- L to 140 --- ---
Urine -- R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 --- R to 140 --- --- ---

Vaseline (Petroleum Jelly)

-- --- N R to 140 N R to 120 --- --- R to 120 --- --- ---
CAS# 8009-03-8

Vegetable Oil -- --- L to 180 R to 140 R to 140 R to 140 --- R to 248 R to 140 --- --- ---

Vinegar
-- R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 --- R to 140 R to 194 --- ---
CAS# 64-19-7
Vinyl Acetate
CAS# 108-05-4 -- --- N R to 73 N R to 140 --- L to 68 R to 140 --- --- ---
CH3COOCH=CH2
Water, Acid Mine
-- R to 160 R to 200 R to 140 R to 140 R to 140 R to 180 --- R to 180 --- --- ---
H2O
Water, Deionized
-- R to 160 R to 200 R to 140 R to 140 R to 140 R to 180 --- R to 180 R to 194 --- ---
H2O
Water, Distilled
-- R to 160 R to 200 R to 212 R to 140 R to 140 R to 180 R to 248 R to 180 R to 194 --- ---
H2O
Water, Potable
-- R to 160 R to 200 R to 212 R to 140 R to 140 R to 180 R to 248 R to 180 R to 194 --- ---
H2O
Water, Salt
-- R to 160 R to 200 R to 212 R to 140 R to 140 R to 180 --- R to 180 R to 194 --- ---
H2O
Water, Sea
-- R to 160 R to 200 R to 212 R to 140 R to 140 R to 180 R to 248 R to 180 R to 194 --- ---
H2O
Water, Soft
-- R to 160 R to 200 R to 212 R to 140 R to 140 R to 180 --- R to 180 R to 194 --- ---
H2O

63
 ***May not be fully applicable to pressurized applications***

PP PE
PA
(PP-R, (MDPE,
Chemical Formula Concentration ABS CPVC PVC PB PVDF PEX (PA11, PSU PPSU
PP- HDPE,
PA12)
RCT) PE-RT)
Water, Residential Waste
-- R to 73 R to 200 R to 212 R to 140 R to 140 R to 180 --- R to 180 R to 194 --- ---
H2O
Whiskey -- --- R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---

White Liquor -- R to 73 R to 180 --- R to 140 --- --- --- --- --- --- ---

Wine -- R to 73 R to 180 R to 140 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
Xylene (Xylol)
CAS# 1330-20-7 -- N N N N N N L to 140 N L to 194 --- ---
C6H4(CH3)2
Zinc Acetate
CAS# 557-34-6 -- --- R to 180 --- --- --- --- --- --- --- --- ---
Zn(CH3COO)2o2H2O
Zinc Carbonate
CAS# 3486-35-9 -- --- R to 180 R to 140 --- R to 140 --- R to 212 R to 140 --- --- ---
ZnCO3
Zinc Chloride -- R to 120 R to 180 R to 180 R to 140 R to 140 --- --- R to 140 --- --- ---
CAS# 76-46-85-7 50% --- --- --- --- --- --- --- --- L to 73 --- ---
ZnCl2 Saturated --- --- --- --- --- --- R to 212 --- --- --- ---
Zinc Nitrate Saturated R to 160 R to 180 R to 180 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 7779-88-6 20% --- --- --- --- --- --- --- --- --- R to 210 ---
Zn(NO3)2o6H2O
Zinc Oxide
CAS# 1314-13-2 -- --- R to 180 --- --- --- --- R to 212 --- --- --- ---
ZnO
Zinc Stearate
CAS# 557-05-1 -- --- --- --- --- --- --- R to 122 --- --- --- ---
(CH3(CH2)16COO)2Zn
Zinc Sulfate Saturated R to 160 R to 180 R to 212 R to 140 R to 140 R to 140 R to 212 R to 140 --- --- ---
CAS# 7733-02-0 20% --- --- --- --- --- --- --- --- --- R to 212 ---
ZnSO4o7H2O

64