SN54LS373, SN54LS374, SN54S373, SN54S374,

SN74LS373, SN74LS374, SN74S373, SN74S374

OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

D Choice of Eight Latches or Eight D-Type SN54LS373, SN54LS374, SN54S373,

Flip-Flops in a Single Package SN54S374 . . . J OR W PACKAGE
SN74LS373, SN74S374 . . . DW, N, OR NS PACKAGE
D 3-State Bus-Driving Outputs SN74LS374 . . . DB, DW, N, OR NS PACKAGE
D Full Parallel Access for Loading SN74S373 . . . DW OR N PACKAGE
(TOP VIEW)
D Buffered Control Inputs
D Clock-Enable Input Has Hysteresis to OC 1 20 VCC
Improve Noise Rejection (’S373 and ’S374) 1Q 2 19 8Q
D P-N-P Inputs Reduce DC Loading on Data 1D 3 18 8D
Lines (’S373 and ’S374) 2D 4 17 7D
2Q 5 16 7Q
description 3Q 6 15 6Q
3D 7 14 6D
These 8-bit registers feature 3-state outputs 4D 8 13 5D
designed specifically for driving highly capacitive 4Q 9 12 5Q
or relatively low-impedance loads. The GND 10 11 C†
high-impedance 3-state and increased
† C for ’LS373 and ’S373; CLK for ’LS374 and ’S374.
high-logic-level drive provide these registers with
the capability of being connected directly to and
driving the bus lines in a bus-organized system SN54LS373, SN54LS374, SN54S373,
SN54S374 . . . FK PACKAGE
without need for interface or pullup components. (TOP VIEW)
These devices are particularly attractive for

VCC
OC
implementing buffer registers, I/O ports,

1Q

8Q
1D
bidirectional bus drivers, and working registers.
3 2 1 20 19
The eight latches of the ’LS373 and ’S373 are 2D 4 18 8D
transparent D-type latches, meaning that while 2Q 5 17 7D
the enable (C or CLK) input is high, the Q outputs 3Q 6 16 7Q
follow the data (D) inputs. When C or CLK is taken 3D 7 15 6Q
low, the output is latched at the level of the data 4D 8 14 6D
that was set up. 9 10 11 12 13

The eight flip-flops of the ’LS374 and ’S374 are

4Q

5Q
5D
GND
edge-triggered D-type flip-flops. On the positive C†
transition of the clock, the Q outputs are set to the † C for ’LS373 and ’S373; CLK for ’LS374 and ’S374.
logic states that were set up at the D inputs.
Schmitt-trigger buffered inputs at the enable/clock lines of the ’S373 and ’S374 devices simplify system design
as ac and dc noise rejection is improved by typically 400 mV due to the input hysteresis. A buffered
output-control (OC) input can be used to place the eight outputs in either a normal logic state (high or low logic
levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines
significantly.
OC does not affect the internal operation of the latches or flip-flops. That is, the old data can be retained or new
data can be entered, even while the outputs are off.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Copyright  2002, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments On products compliant to MIL-PRF-38535, all parameters are tested
standard warranty. Production processing does not necessarily include unless otherwise noted. On all other products, production
testing of all parameters. processing does not necessarily include testing of all parameters.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1

SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

ORDERING INFORMATION
ORDERABLE TOP-SIDE
TA PACKAGE†
PART NUMBER MARKING
Tube SN74LS373N SN74LS373N
Tube SN74LS374N SN74LS374N
PDIP – N
Tube SN74S373N SN74S373N
Tube SN74S374N SN74S374N
Tube SN74LS373DW
LS373
Tape and reel SN74LS373DWR
Tube SN74LS374DW
LS374
Tape and reel SN74LS374DWR
0°C to 70°C SOIC – DW
Tube SN74S373DW
S373
Tape and reel SN74S373DWR
Tube SN74S374DW
S374
Tape and reel SN74S374DWR
Tape and reel SN74LS373NSR 74LS373
SOP – NS Tape and reel SN74LS374NSR 74LS374
Tape and reel SN74S374NSR 74S374
SSOP – DB Tape and reel SN74LS374DBR LS374A
Tube SN54LS373J SN54LS373J
Tube SNJ54LS373J SNJ54LS373J
Tube SN54LS374J SN54LS374J
Tube SNJ54LS374J SNJ54LS374J
CDIP – J
Tube SN54S373J SN54S373J
Tube SNJ54S373J SNJ54S373J
Tube SN54S374J SN54S374J
–55°C to 125°C Tube SNJ54S374J SNJ54S374J
Tube SNJ54LS373W SNJ54LS373W
CFP – W Tube SNJ54LS374W SNJ54LS374W
Tube SNJ54S374W SNJ54S374W
Tube SNJ54LS373FK SNJ54LS373FK
Tube SNJ54LS374FK SNJ54LS374FK
LCCC – FK
Tube SNJ54S373FK SNJ54S373FK
Tube SNJ54S374FK SNJ54S374FK
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

Function Tables

’LS373, ’S373
(each latch)
INPUTS OUTPUT
OC C D Q
L H H H
L H L L
L L X Q0
H X X Z

’LS374, ’S374
(each latch)
INPUTS OUTPUT
OC CLK D Q
L ↑ H H
L ↑ L L
L L X Q0
H X X Z

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3

SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

logic diagrams (positive logic)

’LS373, ’S373 ’LS374, ’S374
Transparent Latches Positive-Edge-Triggered Flip-Flops

1 1
OC OC

11 11
C CLK

C1 2 C1 2
3 1Q 3 1Q
1D 1D 1D 1D

C1 5 C1 5
4 2Q 4 2Q
2D 1D 2D 1D

C1 6 C1 6
7 3Q 7 3Q
3D 1D 3D 1D

C1 9 C1 9
8 4Q 8 4Q
4D 1D 4D 1D

C1 12 C1 12
13 5Q 13 5Q
5D 1D 5D 1D

C1 15 C1 15
14 6Q 14 6Q
6D 1D 6D 1D

C1 16 C1 16
17 7Q 17 7Q
7D 1D 7D 1D

C1 19 C1 19
18 8Q 18 8Q
8D 1D 8D 1D

for ’S373 Only for ’S374 Only

Pin numbers shown are for DB, DW, J, N, NS, and W packages.

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

schematic of inputs and outputs

’LS373
EQUIVALENT OF DATA INPUTS EQUIVALENT OF ENABLE- AND TYPICAL OF ALL OUTPUTS
OUTPUT-CONTROL INPUTS
VCC VCC VCC

Req = 20 kΩ NOM 17 kΩ NOM 100 Ω NOM

Input
Input

Output

’LS374

EQUIVALENT OF DATA INPUTS EQUIVALENT OF CLOCK- AND TYPICAL OF ALL OUTPUTS

OUTPUT-CONTROL INPUTS
VCC VCC VCC

30 kΩ NOM 17 kΩ NOM 100 Ω NOM

Input
Input

Output

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5

SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
(’LS devices)
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W
DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to network ground terminal.
2. The package thermal impedance is calculated in accordance with JESD 51-7.

recommended operating conditions

SN54LS’ SN74LS’
UNIT
MIN NOM MAX MIN NOM MAX
VCC Supply voltage 4.5 5 5 4.75 5 5.25 V
VOH High-level output voltage 5.5 5.5 V
IOH High-level output current –1 –2.6 mA
IOL Low-level output current 12 24 mA
CLK high 15 15
tw Pulse duration ns
CLK low 15 15
’LS373 5↓ 5↓
tsu Data setup time ns
’LS374 20↑ 20↑
’LS373 20↓ 20↓
th Data hold time ns
’LS374‡ 5↑ 0↑
TA Operating free-air temperature –55 125 0 70 °C
‡ The th specification applies only for data frequency below 10 MHz. Designs above 10 MHz should use a minimum of 5 ns (commercial only).

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)
SN54LS’ SN74LS’
PARAMETER TEST CONDITIONS† UNIT
MIN TYP‡ MAX MIN TYP‡ MAX
VIH High-level input voltage 2 2 V
VIL Low-level input voltage 0.7 0.8 V
VIK Input clamp voltage VCC = MIN, II = –18 mA –1.5 –1.5 V
VCC = MIN,, VIH = 2 V,,
VOH High level output voltage
High-level 24
2.4 34
3.4 24
2.4 31
3.1 V
VIL = VIL max, IOH = MAX
VCC = MIN,, VIH = 2 V,, IOL = 12 mA 0.25 0.4 0.25 0.4
VOL Low level output voltage
Low-level V
VIL = VIL max IOL = 24 mA 0.35 0.5
Off-state output current,, VCC = MAX,, VIH = 2 V,,
IOZH 20 20 m A
high-level voltage applied VO = 2.7 V
Off-state output current,, VCC = MAX,, VIH = 2 V,,
IOZL –20
20 –20
20 m A
low-level voltage applied VO = 0.4 V
Input current at maximum
II VCC = MAX
MAX, VI = 7 V 01
0.1 01
0.1 mA
input voltage
IIH High-level input current VCC = MAX, VI = 2.7 V 20 20 m A
IIL Low-level input current VCC = MAX, VI = 0.4 V –0.4 –0.4 mA
IOS Short-circuit output current§ VCC = MAX –30 –130 –30 –130 mA
VCC = MAX,, ’LS373 24 40 24 40
ICC Supply current mA
Output control at 4.5 V ’LS374 27 40 27 40
† For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
‡ All typical values are at VCC = 5 V, TA = 25°C.
§ Not more than one output should be shorted at a time and duration of the short circuit should not exceed one second.

switching characteristics, VCC = 5 V, TA = 25°C (see Figure 1)

FROM TO ’LS373 ’LS374
PARAMETER TEST CONDITIONS UNIT
(INPUT) (OUTPUT) MIN TYP MAX MIN TYP MAX
RL = 667 Ω, CL = 45 pF,
fmax 35 50 MHz
See Note 3
tPLH RL = 667 Ω, CL = 45 pF,, 12 18
Data Any Q ns
tPHL See Note 3 12 18
tPLH RL = 667 Ω, CL = 45 pF,, 20 30 15 28
C or CLK Any Q ns
tPHL See Note 3 18 30 19 28
tPZH RL = 667 Ω, CL = 45 pF,, 15 28 20 26
OC Any Q ns
tPZL See Note 3 25 36 21 28
tPHZ 15 25 15 28
OC Any Q RL = 667 Ω, CL = 5 pF ns
tPLZ 12 20 12 20
NOTE 3: Maximum clock frequency is tested with all outputs loaded.
fmax = maximum clock frequency
tPLH = propagation delay time, low-to-high-level output
tPHL = propagation delay time, high-to-low-level output
tPZH = output enable time to high level
tPZL = output enable time to low level
tPHZ = output disable time from high level
tPLZ = output disable time from low level

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7

SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

schematic of inputs and outputs

’S373 and ’S374 ’S373 and ’S374

EQUIVALENT OF EACH INPUT TYPICAL OF ALL OUTPUTS

VCC VCC

2.8 kΩ NOM 50 Ω NOM

Input

Output

8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
(’S devices)
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Package thermal impedance, θJA (see Note 2): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to network ground terminal.
2. The package thermal impedance is calculated in accordance with JESD 51-7.

recommended operating conditions

SN54S’ SN74S’
UNIT
MIN NOM MAX MIN NOM MAX
VCC Supply voltage 4.5 5 5.5 4.75 5 5.25 V
VOH High-level output voltage 5.5 5.5 V
IOH High-level output current –2 –6.5 mA
High 6 6
tw Pulse duration,
duration clock/enable ns
Low 7.3 7.3
’S373 0↓ 0↓
tsu Data setup time ns
’S374 5↑ 5↑
’S373 10↓ 10↓
th Data hold time ns
’S374 2↑ 2↑
TA Operating free-air temperature –55 125 0 70 °C

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9

SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted) (SN54S373, SN54S374, SN74S373, SN74S374)
PARAMETER TEST CONDITIONS† MIN TYP‡ MAX UNIT
VIH 2 V
VIL 0.8 V
VIK VCC = MIN, II = –18 mA –1.2 V
SN54S’ 2.4 3.4
VOH VCC = MIN
MIN, VIH = 2 V
V, VIL = 0
0.8
8VV, IOH = MAX V
SN74S’ 2.4 3.1
VOL VCC = MIN, VIH = 2 V, VIL = 0.8 V, IOL = 20 mA 0.5 V
IOZH VCC = MAX, VIH = 2 V, VO = 2.4 V 50 m A
IOZL VCC = MAX, VIH = 2 V, VO = 0.5 V –50 m A
II VCC = MAX, VI = 5.5 V 1 mA
IIH VCC = MAX, VI = 2.7 V 50 m A
IIL VCC = MAX, VI = 0.5 V –250 m A
IOS§ VCC = MAX –40 –100 mA
Outputs high 160
’S373 Outputs low 160
Outputs disabled 190
ICC VCC = MAX Outputs high 110 mA
Outputs low 140
’S374
Outputs disabled 160
CLK and OC at 4 V, D inputs at 0 V 180
† For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
‡ All typical values are at VCC= 5 V, TA = 25°C.
§ Not more than one output should be shorted at a time and duration of the short circuit should not exceed one second.

switching characteristics, VCC = 5 V, TA = 25°C (see Figure 2)

FROM TO ’S373 ’S374
PARAMETER TEST CONDITIONS UNIT
(INPUT) (OUTPUT) MIN TYP MAX MIN TYP MAX
RL = 280 Ω, CL = 15 pF,
fmax 75 100 MHz
See Note 3
tPLH RL = 280 Ω, CL = 15 pF,, 7 12
Data Any Q ns
tPHL See Note 3 7 12
tPLH RL = 280 Ω, CL = 15 pF,, 7 14 8 15
C or CLK Any Q ns
tPHL See Note 3 12 18 11 17
tPZH RL = 280 Ω, CL = 15 pF,, 8 15 8 15
OC Any Q ns
tPZL See Note 3 11 18 11 18
tPHZ 6 9 5 9
OC Any Q RL = 280 Ω, CL = 5 pF ns
tPLZ 8 12 7 12
NOTE 3. Maximum clock frequency is tested with all outputs loaded.
fmax = maximum clock frequency
tPLH = propagation delay time, low-to-high-level output
tPHL = propagation delay time, high-to-low-level output
tPZH = output enable time to high level
tPZL = output enable time to low level
tPHZ = output disable time from high level
tPLZ = output disable time from low level

10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

PARAMETER MEASUREMENT INFORMATION

SERIES 54LS/74LS DEVICES
VCC
Test RL
Test Point S1
Point VCC
From Output
VCC Under Test (see Note B)
RL CL
From Output RL (see Note A) 5 kΩ
Under Test (see Note B) From Output Test
CL Under Test Point
(see Note A) CL
(see Note A) S2

LOAD CIRCUIT LOAD CIRCUIT LOAD CIRCUIT

FOR 2-STATE TOTEM-POLE OUTPUTS FOR OPEN-COLLECTOR OUTPUTS FOR 3-STATE OUTPUTS

3V
High-Level Timing
Pulse 1.3 V 1.3 V Input 1.3 V
0V
tw th
tsu
3V
Low-Level Data
1.3 V 1.3 V 1.3 V 1.3 V
Pulse Input
0V
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PULSE DURATIONS SETUP AND HOLD TIMES
Output 3V
Control
(low-level 1.3 V 1.3 V
3V
Input enabling)
1.3 V 1.3 V 0V
0V tPZL tPLZ

tPLH tPHL

In-Phase
Waveform 1 ≈1.5 V
VOH (see Notes C 1.3 V
Output 1.3 V 1.3 V VOL + 0.5 V
and D)
(see Note D) VOL VOL
tPZH tPHZ
tPHL tPLH
VOH
Out-of-Phase Waveform 2 VOH – 0.5 V
VOH
(see Notes C 1.3 V
Output 1.3 V 1.3 V
and D) ≈1.5 V
(see Note D) VOL
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS
NOTES: A. CL includes probe and jig capacitance.
B. All diodes are 1N3064 or equivalent.
C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
D. S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open for tPZL.
E. Phase relationships between inputs and outputs have been chosen arbitrarily for these examples.
F. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω, tr ≤ 1.5 ns, tf ≤ 2.6 ns.
G. The outputs are measured one at a time with one input transition per measurement.
H. All parameters and waveforms are not applicable to all devices .

Figure 1. Load Circuits and Voltage Waveforms

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11

SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

PARAMETER MEASUREMENT INFORMATION

SERIES 54S/74S DEVICES
VCC
Test RL
Test Point S1
Point VCC
From Output
VCC Under Test (see Note B)
RL CL
From Output RL (see Note A) 1 kΩ
Under Test (see Note B) From Output Test
CL Under Test Point
(see Note A) CL
(see Note A) S2

LOAD CIRCUIT LOAD CIRCUIT LOAD CIRCUIT

FOR 2-STATE TOTEM-POLE OUTPUTS FOR OPEN-COLLECTOR OUTPUTS FOR 3-STATE OUTPUTS

3V
High-Level Timing
Pulse 1.5 V 1.5 V Input 1.5 V
0V
tw th
tsu
3V
Low-Level Data
1.5 V 1.5 V 1.5 V 1.5 V
Pulse Input
0V
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PULSE DURATIONS SETUP AND HOLD TIMES

Output 3V
Control
(low-level 1.5 V 1.5 V
3V
Input 1.5 V 1.5 V enabling) 0V
0V tPZL tPLZ

tPLH tPHL
Waveform 1 ≈1.5 V
In-Phase VOH (see Notes C 1.5 V
Output 1.5 V 1.5 V and D) VOL + 0.5 V
(see Note D) VOL VOL
tPZH tPHZ
tPHL tPLH
VOH
Out-of-Phase VOH Waveform 2 VOH – 0.5 V
(see Notes C 1.5 V
Output 1.5 V 1.5 V ≈1.5 V
(see Note D) and D)
VOL
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS
NOTES: A. CL includes probe and jig capacitance.
B. All diodes are 1N3064 or equivalent.
C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
D. S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open for tPZL.
E. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω; tr and tf ≤ 7 ns for Series
54/74 devices and tr and tf ≤ 2.5 ns for Series 54S/74S devices.
F. The outputs are measured one at a time with one input transition per measurement.
G. All parameters and waveforms are not applicable to all devices .

Figure 2. Load Circuits and Voltage Waveforms

12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN54LS373, SN54LS374, SN54S373, SN54S374,
SN74LS373, SN74LS374, SN74S373, SN74S374
OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS
SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002

TYPICAL APPLICATION DATA

Bidirectional Bus Driver

Output
Control 1

1D 1Q
2D 2Q
3D 3Q
Bidirectional 4D ’LS374 4Q
or Bidirectional
Data Bus 1 5D 5Q Data Bus 2
’S374
6D 6Q
7D C 7Q
8D 8Q
Clock 1 Clock 2
1Q 1D
2Q C 2D
3Q 3D
4Q ’LS374 4D
or
5Q 5D
’S374
6Q 6D
7Q 7D
8Q 8D
Output
Control 2

Clock 1 H
Bus
Exchange
Clock
Clock 2 H

Clock Circuit for Bus Exchange

Expandable 4-Word by 8-Bit General Register File

’LS374 or ’S374
1/2 SN74LS139
or SN74S139
G Y0 ’LS374 or ’S374
Y1
A Y2
Enable Select B Y3 ’LS374 or ’S374

’LS374 or ’S374

1/2 SN74LS139 Y0 Y1 Y2 Y3
or SN74S139 A B G

Clock
Clock
Select

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13

 PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2022

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)

78011022A ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 78011022A Samples
& Green SNJ54LS
374FK
7801102RA ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 7801102RA Samples
& Green SNJ54LS374J
7801102SA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 7801102SA Samples
& Green SNJ54LS374W
JM38510/32502B2A ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502B2A
JM38510/32502BRA ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502BRA
JM38510/32502BSA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502BSA
JM38510/32502SRA ACTIVE CDIP J 20 20 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502SRA
JM38510/32502SSA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502SSA
JM38510/32503B2A ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32503B2A
JM38510/32503BRA ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32503BRA
JM38510/32503BSA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32503BSA
M38510/32502B2A ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502B2A
M38510/32502BRA ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502BRA
M38510/32502BSA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502BSA
M38510/32502SRA ACTIVE CDIP J 20 20 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502SRA
M38510/32502SSA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32502SSA

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2022

Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)

M38510/32503B2A ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32503B2A
M38510/32503BRA ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32503BRA
M38510/32503BSA ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 JM38510/ Samples
& Green 32503BSA
SN54LS373J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SN54LS373J Samples
& Green
SN54LS374J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SN54LS374J Samples
& Green
SN54S373J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SN54S373J Samples
& Green
SN54S374J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SN54S374J Samples
& Green
SN74LS373DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LS373 Samples

SN74LS373DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LS373 Samples

SN74LS373N ACTIVE PDIP N 20 20 RoHS & NIPDAU N / A for Pkg Type 0 to 70 SN74LS373N Samples
Non-Green
SN74LS373NE4 ACTIVE PDIP N 20 20 RoHS & NIPDAU N / A for Pkg Type 0 to 70 SN74LS373N Samples
Non-Green
SN74LS373NSR ACTIVE SO NS 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 74LS373 Samples

SN74LS374DBR ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LS374A Samples

SN74LS374DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LS374 Samples

SN74LS374DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LS374 Samples

SN74LS374N ACTIVE PDIP N 20 20 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN74LS374N Samples

SN74LS374NE4 ACTIVE PDIP N 20 20 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN74LS374N Samples

SN74LS374NSR ACTIVE SO NS 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 74LS374 Samples

SN74S373N ACTIVE PDIP N 20 20 RoHS & NIPDAU N / A for Pkg Type 0 to 70 SN74S373N Samples
Non-Green

Addendum-Page 2
 PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2022

Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)

SN74S374N ACTIVE PDIP N 20 20 RoHS & NIPDAU N / A for Pkg Type 0 to 70 SN74S374N Samples
Non-Green
SNJ54LS373FK ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54LS Samples
& Green 373FK
SNJ54LS373J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54LS373J Samples
& Green
SNJ54LS373W ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54LS373W Samples
& Green
SNJ54LS374FK ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 78011022A Samples
& Green SNJ54LS
374FK
SNJ54LS374J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 7801102RA Samples
& Green SNJ54LS374J
SNJ54LS374W ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 7801102SA Samples
& Green SNJ54LS374W
SNJ54S373FK ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54S Samples
& Green 373FK
SNJ54S373J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54S373J Samples
& Green
SNJ54S374FK ACTIVE LCCC FK 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54S Samples
& Green 374FK
SNJ54S374J ACTIVE CDIP J 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54S374J Samples
& Green
SNJ54S374W ACTIVE CFP W 20 1 Non-RoHS SNPB N / A for Pkg Type -55 to 125 SNJ54S374W Samples
& Green

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Addendum-Page 3
 PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2022

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF SN54LS373, SN54LS373-SP, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 :

• Catalog : SN74LS373, SN54LS373, SN74LS374, SN74S373, SN74S374

• Military : SN54LS373, SN54LS374, SN54S373, SN54S374
• Space : SN54LS373-SP

NOTE: Qualified Version Definitions:

• Catalog - TI's standard catalog product

• Military - QML certified for Military and Defense Applications
• Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application

Addendum-Page 4
 PACKAGE MATERIALS INFORMATION

www.ti.com 4-Oct-2022

TAPE AND REEL INFORMATION

REEL DIMENSIONS TAPE DIMENSIONS

K0 P1

B0 W
Reel
Diameter
Cavity A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
W Overall width of the carrier tape
P1 Pitch between successive cavity centers

Reel Width (W1)

QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE

Sprocket Holes

Q1 Q2 Q1 Q2

Q3 Q4 Q3 Q4 User Direction of Feed

Pocket Quadrants

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
SN74LS373DWR SOIC DW 20 2000 330.0 24.4 10.8 13.3 2.7 12.0 24.0 Q1
SN74LS373NSR SO NS 20 2000 330.0 24.4 8.4 13.0 2.5 12.0 24.0 Q1
SN74LS374DBR SSOP DB 20 2000 330.0 16.4 8.2 7.5 2.5 12.0 16.0 Q1
SN74LS374DWR SOIC DW 20 2000 330.0 24.4 10.8 13.3 2.7 12.0 24.0 Q1
SN74LS374NSR SO NS 20 2000 330.0 24.4 8.4 13.0 2.5 12.0 24.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 4-Oct-2022

TAPE AND REEL BOX DIMENSIONS

Width (mm)
H
W

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74LS373DWR SOIC DW 20 2000 367.0 367.0 45.0
SN74LS373NSR SO NS 20 2000 367.0 367.0 45.0
SN74LS374DBR SSOP DB 20 2000 356.0 356.0 35.0
SN74LS374DWR SOIC DW 20 2000 367.0 367.0 45.0
SN74LS374NSR SO NS 20 2000 356.0 356.0 41.0

Pack Materials-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 4-Oct-2022

TUBE

T - Tube
height L - Tube length

W - Tube
width

B - Alignment groove width

*All dimensions are nominal

Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)
78011022A FK LCCC 20 1 506.98 12.06 2030 NA
7801102SA W CFP 20 1 506.98 26.16 6220 NA
JM38510/32502B2A FK LCCC 20 1 506.98 12.06 2030 NA
JM38510/32502BSA W CFP 20 1 506.98 26.16 6220 NA
JM38510/32502SSA W CFP 20 1 506.98 26.16 6220 NA
JM38510/32503B2A FK LCCC 20 1 506.98 12.06 2030 NA
JM38510/32503BSA W CFP 20 1 506.98 26.16 6220 NA
M38510/32502B2A FK LCCC 20 1 506.98 12.06 2030 NA
M38510/32502BSA W CFP 20 1 506.98 26.16 6220 NA
M38510/32502SSA W CFP 20 1 506.98 26.16 6220 NA
M38510/32503B2A FK LCCC 20 1 506.98 12.06 2030 NA
M38510/32503BSA W CFP 20 1 506.98 26.16 6220 NA
SN74LS373DW DW SOIC 20 25 507 12.83 5080 6.6
SN74LS373N N PDIP 20 20 506 13.97 11230 4.32
SN74LS373NE4 N PDIP 20 20 506 13.97 11230 4.32
SN74LS374DW DW SOIC 20 25 507 12.83 5080 6.6
SN74LS374N N PDIP 20 20 506 13.97 11230 4.32
SN74LS374NE4 N PDIP 20 20 506 13.97 11230 4.32
SN74S373N N PDIP 20 20 506 13.97 11230 4.32
SN74S374N N PDIP 20 20 506 13.97 11230 4.32
SNJ54LS373FK FK LCCC 20 1 506.98 12.06 2030 NA
SNJ54LS373W W CFP 20 1 506.98 26.16 6220 NA
SNJ54LS374FK FK LCCC 20 1 506.98 12.06 2030 NA
SNJ54LS374W W CFP 20 1 506.98 26.16 6220 NA
SNJ54S373FK FK LCCC 20 1 506.98 12.06 2030 NA
SNJ54S374FK FK LCCC 20 1 506.98 12.06 2030 NA
SNJ54S374W W CFP 20 1 506.98 26.16 6220 NA

Pack Materials-Page 3
 PACKAGE OUTLINE
DW0020A SCALE 1.200
SOIC - 2.65 mm max height
SOIC

10.63 SEATING PLANE

TYP
9.97
PIN 1 ID 0.1 C
A
AREA
18X 1.27
20
1

13.0 2X
12.6 11.43
NOTE 3

10
11
0.51
20X
7.6 0.31 2.65 MAX
B 0.25 C A B
7.4
NOTE 4

0.33
TYP
0.10

0.25
SEE DETAIL A GAGE PLANE

1.27 0.3
0 -8 0.40 0.1

DETAIL A
TYPICAL

4220724/A 05/2016

NOTES:

1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.43 mm per side.
5. Reference JEDEC registration MS-013.

www.ti.com
 EXAMPLE BOARD LAYOUT
DW0020A SOIC - 2.65 mm max height
SOIC

20X (2) SYMM

1
20

20X (0.6)

18X (1.27)

SYMM

(R0.05)
TYP

10 11

(9.3)

LAND PATTERN EXAMPLE

SCALE:6X

SOLDER MASK METAL UNDER SOLDER MASK

METAL OPENING
OPENING SOLDER MASK

0.07 MAX 0.07 MIN

ALL AROUND ALL AROUND

NON SOLDER MASK SOLDER MASK

DEFINED DEFINED

SOLDER MASK DETAILS

4220724/A 05/2016
NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

www.ti.com
 EXAMPLE STENCIL DESIGN
DW0020A SOIC - 2.65 mm max height
SOIC

20X (2)
SYMM
1
20

20X (0.6)

18X (1.27)

SYMM

10 11

(9.3)

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL
SCALE:6X

4220724/A 05/2016
NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.

www.ti.com
 PACKAGE OUTLINE
DB0020A SCALE 2.000
SSOP - 2 mm max height
SMALL OUTLINE PACKAGE

C
8.2
TYP
A 7.4
0.1 C
PIN 1 INDEX AREA SEATING
18X 0.65 PLANE
20
1

2X
7.5
5.85
6.9
NOTE 3

10
11 0.38
20X
0.22
5.6 0.1 C A B
B
5.0
NOTE 4

2 MAX
(0.15) TYP 0.25
SEE DETAIL A GAGE PLANE

0.95 0.05 MIN

0 -8 0.55

DETAIL A
A 15

TYPICAL

4214851/B 08/2019

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-150.

www.ti.com
 EXAMPLE BOARD LAYOUT
DB0020A SSOP - 2 mm max height
SMALL OUTLINE PACKAGE

20X (1.85) SYMM

1 (R0.05) TYP

20X (0.45) 20

SYMM
18X (0.65)

10 11

(7)

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN
SCALE: 10X

SOLDER MASK METAL UNDER SOLDER MASK

METAL
OPENING SOLDER MASK OPENING

EXPOSED METAL EXPOSED METAL

0.07 MAX 0.07 MIN

ALL AROUND ALL AROUND

NON-SOLDER MASK SOLDER MASK

DEFINED DEFINED
(PREFERRED)
SOLDER MASK DETAILS
15.000

4214851/B 08/2019
NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

www.ti.com
 EXAMPLE STENCIL DESIGN
DB0020A SSOP - 2 mm max height
SMALL OUTLINE PACKAGE

20X (1.85) SYMM

(R0.05) TYP
1
20X (0.45) 20

SYMM
18X (0.65)

10 11

(7)

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL
SCALE: 10X

4214851/B 08/2019
NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.

www.ti.com
 IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated