Tapped-base pillow type units

Variations of tolerance of distance from mounting

UCPA bottom to center of spherical bore (3Hs) and
Cylindrical bore (with set screws) variations of tolerance of distance between centers
of bolt holes (3Js)
d 12 ~ 50 mm S
B
Unit: mm
Housing No. 3Hs 3Js
PA204~PA210 ±0.15 ±0.5

φd H2

H
H3
A L1 2-N
J
L

Shaft Dia. Dimensions Unit Housing Bearing Basic Factor Mass

mm inch inch No. No. No. Load Ratings
mm kN

d H L A J N H2 H3 L1 B S Cr C0r f0 kg

12 UCPA201 UC201 0.64

1/2 UCPA201-8 UC201-8
15 UCPA202 UC202 0.62
5/8
1 3/16 3 1 9/16 2 3/64 2 3/8 1/2 1 1/16 1.220 0.500
UCPA202-10 PA204 UC202-10 12.8 6.65 13.2
30.2 76 40 52 M10×1.5 60 13 27 31 12.7
17 UCPA203 UC203 0.61
3/4 UCPA204-12 UC204-12
20 UCPA204 UC204 0.59
7/8 UCPA205-14 UC205-14
15/16 1 7/16 3 5/16 1 25/32 2 13/64 2 25/32 1/2 1 3/16 1.343 0.563 UCPA205-15 UC205-15
25 PA205 14.0 7.85 13.9 0.83
36.5 84 45 56 M10×1.5 71 13 30 34.1 14.3 UCPA205 UC205
1 UCPA205-16 UC205-16
1 1/8 UCPA206-18 UC206-18
1 11/16 3 11/16 1 31/32 2 19/32 3 5/16 23/32 1 13/32 1.500 0.626 UCPA206 UC206
30 PA206 19.5 11.3 13.9 1.2
1 3/16 42.9 94 50 66 M14×2 84 18 36 38.1 15.9 UCPA206-19 UC206-19
1 1/4 UCPA206-20 UC206-20
1 1/4 UCPA207-20 UC207-20
1 5/16 UCPA207-21 UC207-21
1 7/8 3 11/32 2 5/32 3 5/32 3 21/32 25/32 1 5/8 1.689 0.689
35 1 3/8 UCPA207-22 PA207 UC207-22 25.7 15.4 13.9 1.7
47.6 110 55 80 M14×2 93 20 41 42.9 17.5
UCPA207 UC207
1 7/16 UCPA207-23 UC207-23
1 1/2 UCPA208-24 UC208-24
1 15/16 4 9/16 2 9/32 3 5/16 3 15/16 25/32 1 5/8 1.937 0.748
40 1 9/16 UCPA208-25 PA208 UC208-25 29.1 17.8 14.0 2.0
49.2 116 58 84 M14×2 100 20 41 49.2 19
UCPA208 UC208
1 5/8 UCPA209-26 UC209-26
1 11/16 2 9/64 4 23/32 2 3/8 3 35/64 4 3/16 31/32 1 21/32 1.937 0.748 UCPA209-27 UC209-27
45 PA209 34.1 21.3 14.0 2.2
1 3/4 54.2 120 60 90 M14×2 106 25 42 49.2 19 UCPA209-28 UC209-28
UCPA209 UC209
1 7/8 UCPA210-30 UC210-30
1 15/16 2 1/4 5 1/8 2 17/32 3 45/64 4 7/16 31/32 1 27/32 2.031 0.748 UCPA210-31 UC210-31
50 PA210 35.1 23.3 14.4 2.8
57.2 130 64 94 M16×2 113 25 47 51.6 19 UCPA210 UC210
2 UCPA210-32 UC210-32
Remarks 1. In Part No. of unit, fitting codes follow bore diameter codes. (See Table 10.5 in P.51.) 4. As for the dimensions and forms of applicable bearings, see the dimensional tables of ball bearing for unit.
2. Part No. of the applicable grease fitting is A-1/4-28UNF. 5. Tapered bore (with adapter) type products are also available. (Example of Part No. : UKPA205J + H305X, UK205 + H305X)
3. As for the triple seal type product (from 201 to 205 are the double seal type products), accessory code L3 (or L2) follows Part No. of unit 6. Housings of nodular graphite cast iron are also available.
or bearing. (Example of Part No. : UCPA206JL3, UC206L3)

102 103