SAFETY DATA SHEET

1. Identification
Product identifier Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal
Other means of identification
Part Number 83417; 83418; 83420
Synonyms Formula Code: B143M(yellow), B139M(pink), B262M(blue) * Part Numbers: 83417(yellow),
83418(blue), 83420(pink)
Recommended use Industrial Use Only
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name ITW Pro Brands
Address 805 E. Old 56 Highway
Olathe, KS 66061
Country (U.S.A.)
Tel: +1 800-443-9536
In Case of Emergency 1-800-535-5053 (Infotrac)

2. Hazard(s) identification
Physical hazards Flammable liquids Category 2
Health hazards Serious eye damage/eye irritation Category 2A
Germ cell mutagenicity Category 1B
Reproductive toxicity Category 1B
Specific target organ toxicity, single exposure Category 3 narcotic effects
Environmental hazards Not classified.
OSHA defined hazards Not classified.

Label elements

Signal word Danger

Hazard statement Highly flammable liquid and vapor. Causes serious eye irritation. May cause genetic defects. May
damage fertility or the unborn child. May cause drowsiness or dizziness.
Precautionary statement
Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep
container tightly closed. Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Avoid breathing mist or vapor. Wash thoroughly after
handling. Use only outdoors or in a well-ventilated area. Wear protective gloves/protective
clothing/eye protection/face protection.
Response If exposed or concerned: Get medical advice/attention. If on skin (or hair): Take off immediately all
contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person to fresh air and
keep comfortable for breathing. Call a poison center/doctor if you feel unwell. If in eyes: Rinse
cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. If eye irritation persists: Get medical advice/attention. In case of fire: Use
appropriate media to extinguish.
Storage Keep cool. Store in a well-ventilated place. Keep container tightly closed. Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 1 / 10

Hazard(s) not otherwise None known.
classified (HNOC)
Supplemental information None.

3. Composition/information on ingredients
Mixtures
Chemical name Common name and synonyms CAS number %
Methyl Ethyl Ketone 78-93-3 30 - 40
Mica Group Minerals 12001-26-2 10 - 20
Rutile(TiO2) 1317-80-2 5 - 15
Pigment Proprietary 1-5
Diacetone Alcohol 123-42-2 1-3
Kaolin 1332-58-7 0.1 - 1
Methyl Benzimidazole-2-yi 10605-21-7 0.1 - 1
Carbamate
Tin Oxide (SnO2) 18282-10-5 0.1 - 1
Dipropylene Glycol Monomethyl 34590-94-8 <0.1
Ether

4. First-aid measures
Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Skin contact Take off immediately all contaminated clothing. Rinse skin with water/shower. Get medical
attention if irritation develops and persists.
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.
Ingestion Rinse mouth. Get medical attention if symptoms occur.
Most important May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
symptoms/effects, acute and Symptoms may include stinging, tearing, redness, swelling, and blurred vision.
delayed
Indication of immediate Provide general supportive measures and treat symptomatically. Thermal burns: Flush with water
medical attention and special immediately. While flushing, remove clothes which do not adhere to affected area. Call an
treatment needed ambulance. Continue flushing during transport to hospital. Keep victim under observation.
Symptoms may be delayed.
General information Take off all contaminated clothing immediately. IF exposed or concerned: Get medical
advice/attention. If you feel unwell, seek medical advice (show the label where possible). Ensure
that medical personnel are aware of the material(s) involved, and take precautions to protect
themselves. Show this safety data sheet to the doctor in attendance. Wash contaminated clothing
before reuse.

5. Fire-fighting measures
Suitable extinguishing media Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire.
media
Specific hazards arising from Vapors may form explosive mixtures with air. Vapors may travel considerable distance to a source
the chemical of ignition and flash back. During fire, gases hazardous to health may be formed.
Special protective equipment Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
and precautions for firefighters
Fire fighting In case of fire and/or explosion do not breathe fumes. Move containers from fire area if you can do
equipment/instructions so without risk.
Specific methods Use standard firefighting procedures and consider the hazards of other involved materials.
General fire hazards Highly flammable liquid and vapor.

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 2 / 10

6. Accidental release measures
Personal precautions, Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Eliminate all
protective equipment and ignition sources (no smoking, flares, sparks, or flames in immediate area). Wear appropriate
emergency procedures protective equipment and clothing during clean-up. Avoid breathing mist or vapor. Do not touch
damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate
closed spaces before entering them. Local authorities should be advised if significant spillages
cannot be contained.
Methods and materials for Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep
containment and cleaning up combustibles (wood, paper, oil, etc.) away from spilled material. Take precautionary measures
against static discharge. Use only non-sparking tools.

Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Use a non-combustible material like vermiculite, sand or earth to soak up the product
and place into a container for later disposal. Following product recovery, flush area with water.

Small Spills: Absorb with earth, sand or other non-combustible material and transfer to containers
for later disposal. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.

Never return spills to original containers for re-use. Put material in suitable, covered, labeled
containers.
Environmental precautions Avoid discharge into drains, water courses or onto the ground.

7. Handling and storage

Precautions for safe handling Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Do not handle, store or open near an open flame, sources of heat or sources of
ignition. Protect material from direct sunlight. When using do not smoke. Explosion-proof general
and local exhaust ventilation. Take precautionary measures against static discharges. All
equipment used when handling the product must be grounded. Use non-sparking tools and
explosion-proof equipment. Avoid breathing mist or vapor. Avoid contact with eyes. Avoid
prolonged exposure. Should be handled in closed systems, if possible. Wear appropriate personal
protective equipment. Observe good industrial hygiene practices.
Conditions for safe storage, Store locked up. Keep away from heat, sparks and open flame. Prevent electrostatic charge
including any incompatibilities build-up by using common bonding and grounding techniques. Store in a cool, dry place out of
direct sunlight. Store in original tightly closed container. Store in a well-ventilated place. Keep in an
area equipped with sprinklers.

8. Exposure controls/personal protection

Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components Type Value
Diacetone Alcohol (CAS PEL 240 mg/m3
123-42-2)
50 ppm
Dipropylene Glycol PEL 600 mg/m3
Monomethyl Ether (CAS
34590-94-8)
100 ppm
Methyl Ethyl Ketone (CAS PEL 590 mg/m3
78-93-3)
200 ppm
US. OSHA Table Z-3 (29 CFR 1910.1000)
Components Type Value
Mica Group Minerals (CAS TWA 20 mppcf
12001-26-2)
US. ACGIH Threshold Limit Values
Components Type Value Form

Diacetone Alcohol (CAS TWA 50 ppm

123-42-2)

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 3 / 10

 US. ACGIH Threshold Limit Values
Components Type Value Form

Dipropylene Glycol STEL 150 ppm

Monomethyl Ether (CAS
34590-94-8)
TWA 100 ppm
Kaolin (CAS 1332-58-7) TWA 2 mg/m3 Respirable fraction.
Methyl Ethyl Ketone (CAS STEL 300 ppm
78-93-3)
TWA 200 ppm
Mica Group Minerals (CAS TWA 3 mg/m3 Respirable fraction.
12001-26-2)
US. NIOSH: Pocket Guide to Chemical Hazards
Components Type Value Form

Diacetone Alcohol (CAS TWA 240 mg/m3

123-42-2)
50 ppm
Dipropylene Glycol STEL 900 mg/m3
Monomethyl Ether (CAS
34590-94-8)
150 ppm
TWA 600 mg/m3
100 ppm
Kaolin (CAS 1332-58-7) TWA 5 mg/m3 Respirable.
10 mg/m3 Total
Methyl Ethyl Ketone (CAS STEL 885 mg/m3
78-93-3)
300 ppm
TWA 590 mg/m3
200 ppm
Mica Group Minerals (CAS TWA 3 mg/m3 Respirable.
12001-26-2)
Tin Oxide (SnO2) (CAS TWA 2 mg/m3
18282-10-5)
Biological limit values
ACGIH Biological Exposure Indices
Components Value Determinant Specimen Sampling Time
Methyl Ethyl Ketone (CAS 2 mg/l MEK Urine *
78-93-3)
* - For sampling details, please see the source document.
Exposure guidelines
US - California OELs: Skin designation
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8) Can be absorbed through the skin.
US - Tennessee OELs: Skin designation
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8) Can be absorbed through the skin.
US ACGIH Threshold Limit Values: Skin designation
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8) Can be absorbed through the skin.
US NIOSH Pocket Guide to Chemical Hazards: Skin designation
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8) Can be absorbed through the skin.
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8) Can be absorbed through the skin.
Appropriate engineering Explosion-proof general and local exhaust ventilation. Good general ventilation (typically 10 air
controls changes per hour) should be used. Ventilation rates should be matched to conditions. If
applicable, use process enclosures, local exhaust ventilation, or other engineering controls to
maintain airborne levels below recommended exposure limits. If exposure limits have not been
established, maintain airborne levels to an acceptable level. Provide eyewash station. Eye wash
fountain and emergency showers are recommended.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear safety glasses with side shields (or goggles).

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 4 / 10

 Skin protection
Hand protection Wear appropriate chemical resistant gloves.
Other Wear suitable protective clothing. Use of an impervious apron is recommended.
Respiratory protection Use a positive-pressure air-supplied respirator if there is any potential for an uncontrolled release,
exposure levels are not known, or any other circumstances where air-purifying respirators may not
provide adequate protection.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.

General hygiene Observe any medical surveillance requirements. When using do not smoke. Always observe good
considerations personal hygiene measures, such as washing after handling the material and before eating,
drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove
contaminants.

9. Physical and chemical properties

Appearance
Physical state Liquid.
Form Liquid.
Color Opaque.
Odor Mild.
Odor threshold Not available.
pH Not available.
Melting point/freezing point Not available.
Initial boiling point and boiling 175 °F (79.44 °C)
range
Flash point 23.0 °F (-5.0 °C) Tag Closed Cup
Evaporation rate >1
Flammability (solid, gas) Not applicable.
Upper/lower flammability or explosive limits
Flammability limit - lower 2%
(%)
Flammability limit - upper 11.5 %
(%)
Explosive limit - lower (%) Not available.
Explosive limit - upper (%) Not available.
Vapor pressure Not available.
Vapor density >1
Relative density Not available.
Solubility(ies)
Solubility (water) Not available.
Partition coefficient Not available.
(n-octanol/water)
Auto-ignition temperature Not available.
Decomposition temperature Not available.
Viscosity Not available.
Other information
Explosive properties Not explosive.
Oxidizing properties Not oxidizing.
Specific gravity > 1 @ 70°F
VOC 38 % w/w

10. Stability and reactivity

Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 5 / 10

Possibility of hazardous Hazardous polymerization does not occur.
reactions
Conditions to avoid Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the
flash point. Contact with incompatible materials.
Incompatible materials Strong oxidizing agents. Ammonia. Amines. Isocyanates. Caustics.
Hazardous decomposition Upon decomposition this product emits acrid dense smoke with carbon dioxide, carbon monoxide,
products water and other products of combustion.

11. Toxicological information

Information on likely routes of exposure
Inhalation May cause drowsiness and dizziness. Headache. Nausea, vomiting. Prolonged inhalation may be
harmful.
Skin contact Frequent or prolonged contact may defat and dry the skin, leading to discomfort and dermatitis.
Eye contact Causes serious eye irritation.
Ingestion Expected to be a low ingestion hazard.
Symptoms related to the May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
physical, chemical and Symptoms may include stinging, tearing, redness, swelling, and blurred vision.
toxicological characteristics
Information on toxicological effects
Acute toxicity Not expected to be acutely toxic.
Components Species Test Results
Diacetone Alcohol (CAS 123-42-2)
Acute
Dermal
LD50 Rat > 1875 mg/kg, 24 Hours
Oral
LD50 Rat 3002 mg/kg
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8)
Acute
Dermal
LD50 Rat > 20 ml/kg, Hours
Oral
LD50 Rat 5.4 ml/kg
Methyl Benzimidazole-2-yi Carbamate (CAS 10605-21-7)
Acute
Dermal
LD50 Rat 2000 mg/kg
Methyl Ethyl Ketone (CAS 78-93-3)
Acute
Oral
LD50 Rat 2054 mg/kg
Rutile(TiO2) (CAS 1317-80-2)
Acute
Oral
LD50 Rat > 2000 mg/kg
Skin corrosion/irritation Prolonged skin contact may cause temporary irritation.
Serious eye damage/eye Causes serious eye irritation.
irritation
Respiratory or skin sensitization
Respiratory sensitization Not a respiratory sensitizer.
Skin sensitization This product is not expected to cause skin sensitization.
Germ cell mutagenicity May cause genetic defects.
Carcinogenicity This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 6 / 10

 ACGIH Carcinogens
Kaolin (CAS 1332-58-7) A4 Not classifiable as a human carcinogen.
IARC Monographs. Overall Evaluation of Carcinogenicity
Rutile(TiO2) (CAS 1317-80-2) 2B Possibly carcinogenic to humans.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
US. National Toxicology Program (NTP) Report on Carcinogens
Not listed.
Reproductive toxicity May damage fertility or the unborn child.
Specific target organ toxicity - May cause drowsiness and dizziness.
single exposure
Specific target organ toxicity - Not classified.
repeated exposure
Aspiration hazard Not an aspiration hazard.
Chronic effects Prolonged inhalation may be harmful. Prolonged exposure may cause chronic effects.
Further information Symptoms may be delayed.

12. Ecological information

Ecotoxicity The product is not classified as environmentally hazardous. However, this does not exclude the
possibility that large or frequent spills can have a harmful or damaging effect on the environment.
Components Species Test Results
Diacetone Alcohol (CAS 123-42-2)
Aquatic
Fish LC50 Bluegill (Lepomis macrochirus) 420 mg/l, 96 hours
Methyl Benzimidazole-2-yi Carbamate (CAS 10605-21-7)
Aquatic
Fish LC50 Channel catfish (Ictalurus punctatus) 0.009 - 0.015 mg/l, 96 hours
Methyl Ethyl Ketone (CAS 78-93-3)
Aquatic
Crustacea EC50 Water flea (Daphnia magna) 4025 - 6440 mg/l, 48 hours
Fish LC50 Sheepshead minnow (Cyprinodon > 400 mg/l, 96 hours
variegatus)
Persistence and degradability
Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
Diacetone Alcohol -0.098
Methyl Benzimidazole-2-yi Carbamate 1.52
Methyl Ethyl Ketone 0.29
Mobility in soil No data available.
Other adverse effects The product contains volatile organic compounds which have a photochemical ozone creation
potential.

13. Disposal considerations

Disposal instructions Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose of
contents/container in accordance with local/regional/national/international regulations.
Local disposal regulations Dispose in accordance with all applicable regulations.
Hazardous waste code The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.

D001: Waste Flammable material with a flash point <140 F

D035: Waste Methyl ethyl ketone
Waste from residues / unused Dispose of in accordance with local regulations. Empty containers or liners may retain some
products product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Contaminated packaging Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal.
Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 7 / 10

14. Transport information
DOT
UN number UN1993
UN proper shipping name Flammable liquids, n.o.s. (Methyl Ethyl Ketone RQ = 13654 LBS), MARINE POLLUTANT
(2-benzimidazolecarbamic Acid Methyl Ester, 3-iodo-2-propynyl Butyl Carbamate)
Transport hazard class(es)
Class 3
Subsidiary risk -
Label(s) 3
Packing group II
Environmental hazards
Marine pollutant Yes
Special precautions for user Not available.
Special provisions IB2, T7, TP1, TP8, TP28
Packaging exceptions 150
Packaging non bulk 202
Packaging bulk 242
IATA
UN number UN1993
UN proper shipping name Flammable liquid, n.o.s. (Methyl Ethyl Ketone)
Transport hazard class(es)
Class 3
Subsidiary risk -
Packing group II
Environmental hazards Yes
ERG Code 3H
Special precautions for user Not available.
Other information
Passenger and cargo Allowed with restrictions.
aircraft
Cargo aircraft only Allowed with restrictions.
IMDG
UN number UN1993
UN proper shipping name FLAMMABLE LIQUID, N.O.S. (Methyl Ethyl Ketone), MARINE POLLUTANT (3-iodo-2-propynyl
Butyl Carbamate, 2-benzimidazolecarbamic Acid Methyl Ester)
Transport hazard class(es)
Class 3
Subsidiary risk -
Packing group II
Environmental hazards
Marine pollutant Yes
EmS F-E, S̲ -E̲
Special precautions for user Not available.
3-iodo-2-propynyl Butyl Carbamate
2-benzimidazolecarbamic Acid Methyl Ester
Transport in bulk according to Not established.
Annex II of MARPOL 73/78 and
the IBC Code
DOT

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 8 / 10

IATA; IMDG

Marine pollutant

15. Regulatory information

US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
Methyl Benzimidazole-2-yi Carbamate (CAS 10605-21-7) Listed.
Methyl Ethyl Ketone (CAS 78-93-3) Listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous Yes
chemical
Classified hazard Flammable (gases, aerosols, liquids, or solids)
categories Acute toxicity (any route of exposure)
Serious eye damage or eye irritation
Germ cell mutagenicity
Reproductive toxicity
Specific target organ toxicity (single or repeated exposure)
SARA 313 (TRI reporting)
Not regulated.

Other federal regulations

Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act Not regulated.
(SDWA)
Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR 1310.02(b) and 1310.04(f)(2) and
Chemical Code Number
Methyl Ethyl Ketone (CAS 78-93-3) 6714

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 9 / 10

 Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures (21 CFR 1310.12(c))
Methyl Ethyl Ketone (CAS 78-93-3) 35 %WV
DEA Exempt Chemical Mixtures Code Number
Methyl Ethyl Ketone (CAS 78-93-3) 6714
FEMA Priority Substances Respiratory Health and Safety in the Flavor Manufacturing Workplace
Methyl Ethyl Ketone (CAS 78-93-3) Low priority
US state regulations California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material
is not known to contain any chemicals currently listed as carcinogens or reproductive toxins.
US. New Jersey Worker and Community Right-to-Know Act
Diacetone Alcohol (CAS 123-42-2)
Dipropylene Glycol Monomethyl Ether (CAS 34590-94-8)
Kaolin (CAS 1332-58-7)
Methyl Benzimidazole-2-yi Carbamate (CAS 10605-21-7)
Methyl Ethyl Ketone (CAS 78-93-3)
Mica Group Minerals (CAS 12001-26-2)
Tin Oxide (SnO2) (CAS 18282-10-5)
California Proposition 65
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,
subd. (a))
Methyl Ethyl Ketone (CAS 78-93-3)
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australia Australian Inventory of Chemical Substances (AICS) Yes
Canada Domestic Substances List (DSL) No
Canada Non-Domestic Substances List (NDSL) No
China Inventory of Existing Chemical Substances in China (IECSC) No
Europe European Inventory of Existing Commercial Chemical Yes
Substances (EINECS)
Europe European List of Notified Chemical Substances (ELINCS) No
Japan Inventory of Existing and New Chemical Substances (ENCS) No
Korea Existing Chemicals List (ECL) No
New Zealand New Zealand Inventory No
Philippines Philippine Inventory of Chemicals and Chemical Substances No
(PICCS)
Taiwan Taiwan Toxic Chemical Substances (TCS) No
United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).

16. Other information, including date of preparation or last revision

Issue date 04-16-2018
Version # 01
Disclaimer ITW Pro Brands cannot anticipate all conditions under which this information and its product, or
the products of other manufacturers in combination with its product, may be used. It is the user’s
responsibility to ensure safe conditions for handling, storage and disposal of the product, and to
assume liability for loss, injury, damage or expense due to improper use. The information provided
in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date
of its publication. The information given is designed only as a guidance for safe handling, use,
processing, storage, transportation, disposal and release and is not to be considered a warranty or
quality specification. The information relates only to the specific material designated and may not
be valid for such material used in combination with any other materials or in any process, unless
specified in the text.
Revision information Product and Company Identification: Alternate Trade Names
Physical & Chemical Properties: Multiple Properties

Material name: Dykem® Cross Check™ Plus Skydrol® - Resistant Torque Seal SDS US

83417; 83418; 83420 Version #: 01 Issue date: 04-16-2018 10 / 10