Scribd
Upload
69 views5 pages

Thread Table

The document provides a standard tap and drill chart for various thread sizes in both imperial and metric units. It lists the recommended drill bit sizes for tapping aluminum, brass, plastic, steel, stainless steel and iron at a 75% thread depth. For each tap size, it specifies the drill size fractionally, in decimal inches, and by number for the material being tapped as well as the corresponding clearance hole size in decimal inches.

Uploaded by

Marko Miljakovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
69 views5 pages

Thread Table

The document provides a standard tap and drill chart for various thread sizes in both imperial and metric units. It lists the recommended drill bit sizes for tapping aluminum, brass, plastic, steel, stainless steel and iron at a 75% thread depth. For each tap size, it specifies the drill size fractionally, in decimal inches, and by number for the material being tapped as well as the corresponding clearance hole size in decimal inches.

Uploaded by

Marko Miljakovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Standard Tap & Drill Chart for 75% Thread Depth

To the best of my knowledge the following information is accurate

Drill Size
Clearance Size
Aluminum, Brass & Plastic Steel, Stainless & Iron
Tap Size
Drill Fractional Decimal Drill Fractional Decimal Drill Decimal
Size Drill Size Size Size Drill Size Size Size Size

0-80 NF 3/64" 3/64" .0469 3/64" 3/64" .0469 #51 .0700"

1-64 #53 1/16" .0595 #53 1/16" .0595 #46 .0810"

1-72 #53 1/16" .0595 #53 1/16" .0595 #46 .0810"

2-56 #50 5/64" .070 #51 5/64" .0670 #41 .0960"

2-64 #50 5/64" .070 #50 5/64" .0700 #41 .0960"

3-48 #47 5/64" .0785 #47 5/64" .0785 #35 .1100"

3-56 #45 5/64" .0820 #46 5/64" .0810 #35 .1100"

4-40 #43 3/32" .0890 #44 3/32" .0860 #30 .1285"

4-48 #42 3/32" .0935 #42 3/32" .0935 #30 .1285"

5-40 #38 7/64" .1015 #40 3/32" .0980 #29 .1360"


5-44 #37 7/64" .1040 #38 3/32" .1015 #29 .1360"

6-32 #36 7/64" .1065 #36 7/64" .1065 #25 .1495"

6-40 #33 7/64" .1130 #34 7/64" .1100 #25 .1495"

8-32 #29 9/64" .1360 #29 9/64" .1360 #16 .1770"

8-36 #29 9/64" .1360 #29 9/64" .1360 #16 .1770"

10-24 #25 5/32" .1495 #26 5/32" .1470 #7 .2010"

10-32 #21 5/32" .1590 #22 5/32" .1570 #7 .2010"


12-24 #16 11/64" .1770 #17 11/64" .1730 #1 .2280"

12-28 #14 3/16" .1820 #15 3/16" .1800 #1 .2280"

12-32 #13 3/16" .1850 #13 3/16" .1850 #1 .2280"

1/4"-20 #7 13/64" .2010 #7 13/64" .2010 H .2660"

1/4"-28 #3 13/64" .2130 #3 13/64" .2130 H .2660"


:
1/4"-32 7/32" 7/32" .2188 7/32" 7/32" .2188 H .2660"

5/16"-18 F 17/64" .2570 F 17/64" .2570 Q .3320"

5/16"-24 I 17/64" .2720 H 17/64" .2660 Q .3320"

5/16"-32 9/32" 9/32" .2812 9/32" 9/32" .2812 Q .3320"

3/8"-16 5/16" 5/16" .3125 5/16" 5/16" .3125 X .3970"

3/8"-24 Q 21/64" .3320 Q 21/64" .3320 X .3970"

3/8"-32 11/32" 11/32" .3438 11/32" 11/32" .3438 X .3970"

7/16"-14 U 23/64" .3680 U 23/64" .3680 15/32" .4687"

7/16"-20 25/64" 25/64" .3906 25/64" 25/64" .3906 15/32" .4687"

7/16"-28 Y 13/32" .4040 Y 13/32" .4040 15/32" .4687"

1/2"-13 27/64" 27/64" .4219 27/64" 27/64" .4219 17/32" .5312"

1/2"-20 29/64" 29/64" .4531 29/64" 29/64" .4531 17/32" .5312"

1/2"-28 15/32" 15/32" .4688 15/32" 15/32" .4688 17/32" .5312"

9/16"-12 31/64" 31/64" .4844 31/64" 31/64" .4844 19/32" .5938"

9/16"-18 33/64" 33/64" .5156 1/2" 1/2" .5000 19/32" .5938"

9/16"-24 33/64" 33/64" .5156 1/2" 1/2" .5000 19/32" .5938"

5/8"-11 17/32" 17/32" .5313 17/32" 17/32" .5313 21/32" .6572"

5/8"-18 37/64" 37/64" .5781 9/16" 9/16" .5625 21/32" .6572"

5/8"-24 37/64" 37/64" .5781 9/16" 9/16" .5625 21/32" .6572"

11/16"-24 41/64" 41/64" .6410 41/64" 41/64" .6410 23/32" .7192"

3/4"-10 21/32" 21/32" .6562 21/32" 21/32" .6562 25/32" .7812"

3/4"-16 11/16" 11/16" .6875 11/16" 11/16" .6875 25/32" .7812"

3/4"-20 45/64" 45/64" .7031 45/64" 45/64" .7031 25/32" .7812"

13/16"-20 49/64" 49/64" .7656 49/64" 49/64" .7656 27/32" .8438"

7/8"-9 49/64" 49/64" .7656 49/64" 49/64" .7656 29/32" .9062"

7/8"-14 13/16" 13/16" .8125 51/64" 51/64" .7969 29/32" .9062"

7/8"-20 53/64" 53/64" .8281 53/64" 53/64" .8281 29/32" .9062"

15/16"-20 57/64" 57/64" .8906 57/64" 57/64" .8906 31/32" .9688"


1"-8 7/8" 7/8" .875 7/8" 7/8" .875 1-1/32" 1.0313"

1"-12 15/16" 15/16" .9375 59/64" 59/64" .9219 1-1/32" 1.0313"

1"-20 61/64" 61/64" .9531 61/64" 61/64" .9531 1-1/32" 1.0313"

1-1/16"-18 1" 1" 1.000 1" 1" 1.000 1-3/32" 1.0938"

1-1/8"-7 63/64" 63/64" .9844 63/64" 63/64" .9844 1-5/32" 1.1562"

1-1/8"-12 1-3/64" 1-3/64" 1.046 1-3/64" 1-3/64" 1.046 1-5/32" 1.1562"

1-1/8"-18 1-1/16" 1-1/16" 1.062 1-1/16" 1-1/16" 1.062 1-5/32" 1.1562"


:
1-3/16"-18 1-1/8" 1-1/8" 1.125 1-1/8" 1-1/8" 1.125 1-7/32" 1.2188"

1-1/4"-7 1-7/64" 1-7/64" 1.1094 1-7/64" 1-7/64" 1.109 1-9/32" 1.2812"

1-1/4"-12 1-11/64" 1-11/64" 1.1719 1-11/64" 1-11/64" 1.172 1-9/32" 1.2812"

1-1/4"-18 1-3/16" 1-3/16" 1.1870 1-3/16" 1-3/16" 1.187 1-9/32" 1.2812"

1-5/16"-18 1-1/4" 1-1/4" 1.250 1-1/4" 1-1/4" 1.250 1-11/32" 1.3738"

1-3/8"-6 1-7/32" 1-7/32" 1.2187 1-7/32" 1-7/32" 1.219 1-13/32" 1.4062"

1-3/8"-12 1-19/64" 1-19/64" 1.2969 1-19/64" 1-19/64" 1.297 1-13/32" 1.4062"

1-3/8"-18 1-5/16" 1-5/16" 1.3125 1-5/16" 1-5/16" 1.313 1-13/32" 1.4062"

1-7/16"-18 1-3/8" 1-3/8" 1.3750 1-3/8" 1-3/8" 1.375 1-15/32" 1.4688"

1-1/2"-6 1-11/32" 1-11/32" 1.3437 1-21/64" 1-21/64" 1.328 1-17/32" 1.5312"

1-1/2"-12 1-27/64" 1-27/64" 1.4219 1-27/64" 1-27/64" 1.422 1-17/32" 1.5312"

1-1/2"-18 1-7/16" 1-7/16" 1.4375 1-7/16" 1-7/16" 1.438 1-17/32" 1.5312"

1-9/16"-18 1-1/2" 1-1/2" 1.5000 1-1/2" 1-1/2" 1.500 1-19/32" 1.5938"

1-5/8"-18 1-9/16" 1-9/16" 1.5625 1-9/16" 1-9/16" 1.563 1-21/32" 1.6562"

1-11/16"-18 1-5/8" 1-5/8" 1.6250 1-5/8" 1-5/8" 1.625 1-23/32" 1.7188"

1-3/4"-5 1-9/16" 1-9/16" 1.5625 1-9/16" 1-9/16" 1.563 1-25/32" 1.7812"

Metric Tap & Drill Chart for 75% Thread Depth


To the best of my knowledge the following information is accurate

Drill Size Clearance Size Drill Size Clearance Size


Tap Size Tap Size
MM Inch MM Inch MM Inch MM Inch

M1.6 x 0.35 1.25 # 55 1.8 # 49 M14 x 2.0 12 15/32" 16 5/8"

M2 x 0.4 1.60 # 52 2.4 # 41 M14 x 1.5 12.5 1/2" 16.0 5/8"

M2.5 x 0.45 2.05 # 46 2.9 # 32 M16 x 2.0 14 35/64" 18 45/64"

M3 x 0.5 2.50 # 39 3.4 # 29 M16 x 1.5 14.5 37/64" 18 45/64"

M3.5 x 0.6 2.90 # 32 3.9 # 23 M18 x 2.5 15.5 39/64" 20.0 51/64"

M4 x 0.7 3.30 # 30 4.5 # 16 M18 x 1.5 16.5 21/32" 20.0 51/64"

M5 x 0.8 4.2 # 19 5.5 7/32" M20 x 2.5 17.5 11/16" 22.0 7/8"

M6 x 1.0 5.0 #8 6.6 G M20 x 1.5 18.5 47/64" 22.0 7/8"

M8 x 1.25 6.8 H 9.0 T M22 x 2.5 19.5 49/64" 25.0 1"

M8 x 1.0 7.0 J 9.0 T M22 x 1.5 20.5 13/16" 25.0 1"


:
M10 x 1.50 8.5 R 12.0 31/64" M24 x 3.0 21 53/64" 27.0 1-5/64"

M10 x 1.25 8.8 11/32" 12.0 31/64" M24 x 2.0 22 7/8" 27.0 1-5/64"

M12 x 1.75 10.2 13/32" 14.0 35/64" M27 x 3.0 24 15/16" 30.0 1-3/16"

M12 x 1.25 10.2 13/32" 14.0 35/64"

Pipe Tap & Drill Chart


To the best of my knowledge the following information is accurate

Tap Size NPT Drill Size NPTF Drill Size NPS Drill Size

1/16" - 27 D D 1/4"

1/8" - 27 Q R 11/32"

1/4" - 18 7/16" 7/16" 7/16"

3/8" - 18 9/16" 37/64" 37/64"

1/2" - 14 45/64" 45/64" 23/32"

3/4" - 14 29/32" 59/64" 59/64"

1" - 11-1/2 1-9/64" 1-5/32" 1-5/32"

1-1/4" - 11-1/2 1-31/64" 1-1/2" 1-1/2"

1-1/2" - 11-1/2 1-47/64" 1-47/64" 1-3/4"

2" - 11-1/2 2-13/64" 2-7/32" 2-7/32"

2-1/2" - 8 2-5/8" 2-41/64" 2-21/32"

3" - 8 3-1/4" 3-9/32"

3-1/2" - 8 3-3/4" 3-25/32"

4" - 8 4-1/4" 4-9/32"

Helicoil Tap & Drill Chart


To the best of my knowledge the following information is accurate

Tap Size Drill Size Tap Size Drill Size Tap Size Drill Size

2 - 56 3/32" 8 - 32 # 17 5/16" - 24 21/64"

3 - 48 # 33 10 - 24 13/64" 3/8" - 16 X
:
4 - 40 # 31 10 - 32 #7 3/8" - 24 25/64"

4 - 48 # 30 12 - 24 #2 7/16" - 14 29/64"

5 - 40 # 30 1/4" - 20 17/64" 7/16" - 20 29/64"

6 - 32 # 25 1/4" - 28 G 1/2" - 13 33/64"

6 - 40 # 26 5/16" - 18 Q 1/2" - 20 33/64"


:

You might also like