NEW POS Technology limited

NEW POS TECHNOLOGY

Precautions
Do not use the non-dedicated power supply, because it may be in trouble due to the mismatch
—
of power.
Do not spill any liquid substance or take any conductive objects into the product, otherwise it
—
will cause a short circuit and damage the product.
Do not vibrate, shake or knock the product sharply.
—
Do not plug in or pull out any external components or equipment in a charging state, it may
—
cause damage to the internal circuitry. Cut off the power before turn off the machine’s power.
Do not place the product in an elevated temperature, humid, dusty or strong electromagnetic
—

NEW9220
field environment.
When a fault occurs, immediately turn off the power supply and discontinue to use the product,
—
please contact the service sector related to our company.
Do not open and repair it by yourself.
—

Smart POS Terminal When the terminal being attacked by unscrupulous environment(such as opening the terminal
—
shell, etc.), the internal sensitive information stored in the terminal will be erased. For avoiding
unnecessary trouble, you should not open the housing.
When the battery reaches the service life, it can not be thrown away, it should be disposed in
—
compliance with local laws and regulations or instructions.

PRODUCT MANUAL

Contents Checklist
The following items should be found inside the box:
1. POS terminal 1PCS
2. AC Power Supply 1PCS
3. Li-ion Battery 1PCS
4. Thermal paper roll 1PCS
5. Product Manual 1PCS

NEW POS TECHNOLOGY LIMITED

NEW9220 www.newpostech.com
 NEW POS Technology limited NEW POS Technology limited

NEW9220 Figure
Handle
Rubber pad Tag label
Paper
1 holder Lid Antenna
inductive zone
Rear camera 18 Flash
Front camera
Tear-off knife

Volume key ON/OFF key

Charge
Battery cover
indicator

Programable
Leds

Front camera
indicator
19 Base contacts

LCD 20 Speaker

Magnetic
stripe card

21 Micro USB port

22 Headphone jack

User smart
card slot

NEW9220 www.newpostech.com NEW9220 www.newpostech.com

 NEW POS Technology limited NEW POS Technology limited

Installation Guidance
NOTE: 1. Confirm the machine is turned off when you install or uninstall the SIM/UIM card, or
1. Install the battery your card will be damaged.
Open the battery cover of the device.
— 2. Do not paste any label on the SIM/SAM card to influence your card thickness, or it
Connect the cable of the battery to the right side battery connector on the machine and
— may result in loading or removing the card can not be carried out smoothly.
put the battery to its place. (Tag label on the battery upwards)
Close the battery cover.
—

Open the battery Install the 3. Power on/off the device

cover figure battery figure
Power on: press and hold the power key until the LCD display, then the machine will be
turned on.
Power off: press and hold the power key more than 2 seconds, then the screen will give you
a tips, you just choose the shutdown key.
Force shut down: Press the power key more than 8 seconds.

4. Install the printer paper

Pull up the handle and open the paper holder Lid.
—
Put the printer paper into paper holder Lid according to the direction of the graphic.
—
Close the paper cover.
—

Open the Paper holder Lid Install the printer paper

NOTE: When removing the battery, please pick up the battery, then gently forced to unplug it to
avoid damage to cables.

2. Install SIM/SAM card

Open the battery cover and remove the battery.
—
Keep the chip side on the SIM/SAM card downward and unfilled corner outward, insert the
—
card to the bottom.
Install the battery and then close the battery cover.
—

Install SIM/SAM/TF card

SAM

NOTE: 1. When install thermal paper, we need the side coated with thermal media facing the
printer heating plate, or you can not print out the characters correctly.
2. Do not keep the printer paperless for long time, or it may cause the roller pasting with
the plate.
3. The temperature is high on the heating plate, please do not touch it without cooling.
4. Tear-off knife edge is sharp, please be careful. Do not touch it for avoiding danger.
TF
SIM

NEW9220 www.newpostech.com NEW9220 www.newpostech.com

 NEW POS Technology limited NEW POS Technology limited

Technical Specifications Note:

1. Warranty valid for 12 months after purchasing date.
Project Technical 2. This warranty will be voided if the product is damaged due to natural disaster, fire,
CPU High Performance 4 Core Processor+Special secure CPU unauthorized alteration or improper usage.
3. Free Warranty covers original parts only
Memory DRAM:1G, FLASH:8G; Supports Micro SD/TF Card, up to 32G 4. Warranty service will not be provided if no the dealer's stamp or this card is missing.
System Android 5.X
Display 5.5 inch 720*1280 pixels capacitive touch screen with e-signature functionality
MS Card Reader Track 1/2/3,bi-directioanl,compliant with ISO7811,7812
Smart Card Reader Supports Memory Card, CPU Card, EMV4.3, PBOC3.0, ISO7816 Standard
Contactless 13.56MHz. Supports Mifare Card,SONY Felica.
Card Reader Compliant with ISO/IEC14443 Type A&B The SAR limit of Europe is 2.0 W/kg. Device types Smart POS Terminal has also been tested against
this SAR limit. The highest SAR value reported under this standard during product certification for
Security MK/SK, DUKPT, FIXED.3DES, RSA, AES, SHA-256, SM2, SM3, Sm4.
use worn on the body is 1.003 W/kg. This device was tested for typical body-worn operations with
Communications 4G/3G/2G, WiFi, Bluetooth. the back of the handset kept 0cm from the body. To maintain compliance with RF exposure
Satellite Positioning GPS, BEIDOU, GLONASS requirements, use accessories that maintain a 0cm separation distance between the user's body
Camera Front Camera:300 thousand pixel; and the back of the handset. The use of belt clips, holsters and similar accessories should not
Rear Cemara:5-mega pixel, with auto flash and focus contain metallic components in its assembly. The use of accessories that do not satisfy these
Multimedia 720P video recording, 1080P video broadcast requirements may not comply with RF exposure requirements, and should be avoided.
Printer CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
High-speed thermal printer, Paper roll width and diameter: 58mm/40mm
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Ports 1*Micro USB OTG
Buttons 1*Power switch, 2*Volume keys Hereby, NEW POS TECHNOLOGY LIMITED declares that the radio equipment type (Smart POS
Card Slots 1*SIM, 2*SAM, 1*TF Card Terminal, NEW9220) is in compliance with Directive 2014/53/EU.
Battery 7.2V/2600mAh The full text of the EU declaration of conformity
Power Input:100-240V AC, 50/60Hz; Output:5.0V DC, 2.0A is available at the following internet address:
Dimensions 184mm*84mm*60mm(L*W*H) http://www.newpostech.com/
Working Temperature:0℃ ~ 50℃(32℉~ 122℉).
Notice: This device may be used in each member state in EU
Environment Humidity:10% ~ 90% (non-condense).
Storage Temperature: -20℃ ~ 60℃(-4℉~140℉). The device is restricted to indoor use when operated in
Environment Humidity: 5% ~ 95% (non-condense). Belgium(BE), Bulgaria(BG), Czech Republic(CZ),
Certifications PCI PTS 5.X, EMV LEVEL 1&2, EMVContactless, CE, RoHS Denmark(DK), Germany(DE), Estonia(EE), Ireland(IE),
CUP, PBOC3.0, QPBOC3.0 Greece(EL), Spain(ES), France(FR), Croatia(HR), Italy(IT),
Optional Docking Station Cyprus(CY), Latvia(LV), Lithuania(LT), Luxembourg(LU),
BLE(2402-2480MHz):-0.1dBm Hungary(HU), Malta(MT), Netherlands(NL), Austria(AT),
BT3.0(2402-2480MHz):5.4dBm Poland(PL), Portugal(PT), Romania(RO), Slovenia(SI),
Wifi(2412-2472MHz):15.49dBm Wifi(5.15-5.725MHz):14.61dBm S l ova k i a ( S K ) , F i n l a n d ( F I ) , Swe d e n ( S E ) , U n i te d
Max RF GSM900: 30.91dBm/1800: 30.65dBm Kingdom(UK), Turkey(TR), Norway(NO), Switzerland(CH),
power level WCDMA B1: 22.00dBm/B8: 21.39dBm Iceland (IS) and Liechtenstein(LI) using frequency in
LTE B1: 21.49dBm/B3: 21.35dBm/B7: 21.72dBm/B8: 21.61dBm/ 5150MHz~5350.
B20: 21.56dBm/B38: 22.18dBm/B40: 22.41dBm
NFC

NEW9220 www.newpostech.com NEW9220 www.newpostech.com 7

 NEW POS Technology limited NEW POS Technology limited

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.

Note: The grantee is not responsible for any changes or modifications not expressly approved by
the party responsible for compliance. Such modifications could void the user’s authority to operate
the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help

The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Portable
Smart POS Terminal (FCC ID: WAL9220) has also been tested against this SAR limit. The highest SAR
value reported under this standard during product certification when properly worn on the body is
1.022W/kg. This device was tested for typical body-worn operations with the back of the handset
kept 0cm from the body. To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 0cm separation distance between the user's body and the back of the
handset. The use of belt clips, holsters and similar accessories should not contain metallic
components in its assembly. The use of accessories that do not satisfy these requirements may not
comply with FCC RF exposure requirements, and should be avoided.

NEW POS TECHNOLOGY LIMITED

Address: 14/A, Financial Technology Building, Financial & Technology
Building, No.11, Keyuan Rd, Nanshan District, ShenZhen, China
Tel: +86-755-86938425 Fax: +86-755-82790632
E-mail: [email protected] Postalcode: 518057
NEW9220 www.newpostech.com WebSite: www.newpostech.com