6 5 4 3 2 1

-D
- R30-1M-5 SHEAVE, TYP
ROUTE
APPROX. 2"
SPRING ROD A GUIDE BEAM
SELF LUBRICATING
SHEET KEYNOTES
CLAMP PLATE - BUSHING
STAINLESS STEEL B (MAT: C86300
1. PAINT INSIDE OF HOLES IN PLATES TO AVOID CARBON STEEL
- MANGANESE
GUIDE ROLLER
1
4" CLEARANCE BRONZE) DIRECT CONTACT WITH STAINLESS STEEL TO PREVENT ANODIC
FLANGED CORROSION. PROVIDE SUITABLE CLEARANCE BETWEEN PIN
NUT, TYP ASSEMBLY, TYP SLOTTED HOLE FOR
KEEPER PL AND HOLE TO ACCOUNT FOR PAINT THICKNESS.
GUIDE BEAM BOLTS,
TYP 2. ANTI-SEIZE COMPOUND SHALL BE APPLIED TO ALL THREADS OF
125
UPPER GUIDE ROLLER (SEE SECTION A) STAINLESS STEEL FASTERS DURING ASSEMBLY TO PREVENT

E 125
T-SECTION AT
SELF LUBRICATING
GALLING.
E
SPRING THRUST 3. AT ASSEMBLY TO HOPPER, APPLY RED LOCITE TO STUDS,
1/2" DIA ASTM A193
1 EACH FLOOR, TYP WASHER, TYP NUTS, AND TAPPED HOLES IN HOPPER.
SPRING ROD BOLT WITH A194 NUTS 4"
STAINLESS STEEL AND SS WASHERS, TYP
1 4. TOTAL NO OF GUIDE ROLLER REQUIRED ARE 4 FOR
4"
Thickness = 1" & THE HOPPER.
125 width = 1 1/2"
GUIDE BAR, 5. ALL STAINLESS STEEL (S.S) BOLTS SHALL BE OF ASTM A193
STAINLESS STEEL AND NUTS SHALL BE OF ASTM A194 ALONG WITH
HOPPER PL 316 SS WASHERS.
10 1/2"

125
1" 6. EACH SPRING SHALL BE HELICAL STAINLESS STEEL (AISI 302/304)
125 AND DESIGNED TO RESIST A LATERAL LOAD OF 15% OF THE
HINGE PIN
DIVIDED TOTAL MOVING HOPPER LOAD ( APPROX.16 KIPS) ON

4"
EACH SIDE OF GUIDE ROLLERS. SPRINGS SHALL BE BY GENERAL

1
HOPPER SHEAVE PIN Ø2"
Width = 8"
3' -2 3 4 " =  TO  OF GUIDE ROLLER

MIN WIRE SPRING CO., WESTERN SPRING MANUFACTURING CO.,

thickness = 3/4" (MAT: ASTM A564 MASTER SPRING & WIRE CO., R&L SPRING CO., OR APPROVED
TYPE 630 EQUAL..
125 CONDITION H1150)
D 3/4" DIA ASTM A193
BOLT WITH A194 NUT
7. THRUST WASHERS SHALL BE SELF-LUBRICATING MATERIAL SUCH
AS DEVA, LUBRON, LUBRITE OR APPROVED EQUAL. D
AND LOCK NUT AND
UPPER GUIDE ROLLER MOUNTING 1 SS WASHER, TYP
4" 112"
SCALE: 4"=1'-0"
1 DETAIL
7" SCALE: 12" = 1'-0"
4"

- STAINLESS STEEL
1

SHEAVE AND SHEAVE

HOPPER WITH GUIDE ROLLER AND GUIDE BEAM - PLAN COVER ASSEMBLY
SHEAVE COVER
BOTTOM GUIDE ROLLER SCALE: 6"=1'-0"
STAINLESS STEEL
NUT
WELDED Plate thickness = 1" SCREWS FOR
TO PLATE GUIDE ROLLER MIN 6" OD SHEAVE COVER
1/8" SS GUIDE BAR, MACHINED, STAINLESS STEEL
COVER PL STAINLESS STEEL (MAT: ASTM A564 TYPE 630 NUT WELDED
CONDITION H1075) TO PLATE UPPER
GUIDE
OD = 6" POCKET ROLLER
C ROLLER PIN 1 1/2" MIN
C
1'-01 4"

103 4"

(MAT: ASTM A564

GUIDE ROLLER
TYPE 630 BASE PL
CONDITION H1150)
~

POCKET
FOR

APPROX SHEAVE DIA = Ø 1'-3"

GASKET
GUIDE
ROLLER

BRACKET, TYP BOTTOM

GUIDE
1/4" SS ROUND THRUST WASHER, ROLLER
HEAD SLOTTED SELF LUBRICATING, TYP
SCREW, TYP
2 1/2" DIA ASTM A193
SS NUT TACK WELD - 125 BOLT WITH A194
TO HOPPER SIDE WALL NUTS AND SS
BOTTOM GUIDE ROLLER MOUNTING 2 DETAIL WASHER, TYP

SCALE: 4"=1'-0" 1 - SCALE: 12" = 1'-0"

-
GUIDE BAR, TYP
512" SHEAVE AND GUIDE ROLLERS - ISOMETRIC VIEW
3 3 4"

1'-01 4"
SUPPORT PL, TYP 1012"
NO SCALE
B T-SECTION AT
EACH FLOOR, TYP B
SELF LUBRICATING STAINLESS STEEL
BUSHING (MAT:C86300 SHEAVE, TYP
ORKOT TXM
125

MANGANESE BRONZE) PROFESSIONAL CERTIFICATION

BEARING PAD
STAINLESS STEEL I hereby certify that these documents were prepared or
approved by me, and that I am a duly licensed professional
WIRE ROPE, TYP engineer under the laws of State of Maryland, License
BASE PL (6 X 37 IWRC) No. 51801, Expiration Date 11/22/2023.
OVAL SHAPED HOLES
FOR 3/4" BOLTS FOR
312"

TABLE OF ADDITIONS & CHANGES

FIELD ADJUSTMENT USE ONLY PRINTS SHOWING LATEST DATE MECHANICAL JOB. NO.
OF GUIDE BEAM DURING
DESCRIPTION CONOWINGO FISH PASSAGE

CHK'D
REV'D

APP'D
FIELD INSTALLATION

02/18/22 09/24/21 DATE

NO.
WEST FISH LIFT IMPROVEMENTS

CWS
DEW
FISH HOPPER GUIDE ROLLER DETAILS

KAR
GUIDE BEAM, TYP 100% ISSUED FOR CONSTRUCTION

0
3"

8"
CONOWINGO HYDROELECTRIC STATION

CWS
DEW
100% ISSUED FOR CONSTRUCTION
A EXELON GENERATION A

KAR
1
SCALE DESIGN CADD CHECKED INSPECTED APPROVED DATE
93 4"
AS SHOWN VN MZ DEW

APPROVED APPROVED
A SECTION SECTION
B APPROVED APPROVED
- SCALE: 3"=1'-0"
(BOLT, NUTS, SHIMS NOT SHOWN FOR CLARITY)
- SCALE: 6"=1'-0" SHEAVE DETAIL 0 1" APPROVED APPROVED

D- R30-1M-5
BAR MEASURES ONE
SCALE: 6"=1'-0" INCH ON ORIGINAL
DRAWINGS SHEET OF -
6 5 4 3 2 1
EXELON POWER
GENERATION SUPPORT