Nols Muller

DC drives
Upgrade Kits DCV700/DCS500/DCS600 
DCS800

© ABB Group
May 13, 2013 | Slide 1
DCS800-R Upgrade Kits
Upgrade solutions for DCS500 / DCS800 drives

 Upgrade of DCS500 / DCS500B / DCS600 to DCS800

 Available for modules
 DCS500 / DCV700 (based on SDCS-CON-1)
 680A … 5150A
 Sizes: C2b, C3, C4
 DCS500B / DCS600 (based on SDCS-CON-2)
 900A … 5200A
 Sizes: A5, A6, A7
 Content of an Upgrade Kit (Standard)
 Control board SDCS-CON-4 with SDCS-DSL-4
 Electronics power supply board SDCS-POW-4
 Measuring board SDCS-PIN-51 (only when needed)
 DCS800 Control Panel
 Cables
 Mechanical parts for assembling

© ABB Group
May 13, 2013 | Slide 2
DCS800-R Upgrade Kits
Availability overview for DCS500/DCV700

DCS800-R Upgrade kits are only available for yellow highlighted converter types
© ABB Group
May 13, 2013 | Slide 3
DCS800-R Upgrade Kits
Availability overview for DCS500B/DCS600

© ABB Group
DCS800-R Upgrade kits are only available for yellow highlighted converter types
May 13, 2013 | Slide 4
DCS800-R Upgrade Kits
Requirements and Design conditions for Upgrades

Requirements Design conditions

 Converter modules DCS500, DCS500B  Max. 24VDC control voltage for SDCS-
(except Unitrol), DCS600 CON-4 instead of 48VDC
 DC Voltage 400VAC up to 1000 VAC  Upgrades DCS600 -> DCS800 require
SDCS-COM-8x board for fiber optic
 Nominal current 680A up to 5200A
connections
 Sufficient physical condition of the
 Old field exciters have to be exchanged
existing module
due to DCSLink Communication.
 Line chokes can be reused if field settings
remain unchanged
 I/O extension board SDCS-IOE-1 has to be
exchanged by RDIO-01 and RAIO-01
 New commissioning tool DriveWindow 2.2
or higher is needed

© ABB Group
May 13, 2013 | Slide 5
DCS800-R Upgrade Kits
Supported and not supported parts
Supported parts Not supported parts
 I/O board SDCS-IOB-2x  all old field exciters for DCS 500, DCS 500B
and DCS 600,
 I/O board SDCS-IOB-3,
 DCS-IOE-1
 control panel CDP 312 xx via SDCS-COM-
81 or SDCS-COM-82 and  control panels CDP 310 and CDP 311
 Nxxx fieldbus adapter used with DCS 500B  Nxxx fieldbus adapter used with DCS 500
or DCS 600 via SDCS-COM-82
 APC1 used for DCV 700
 Reuse of APC2 requires modifications in the
control logic and additional hardware
 All old tools like DDCTool, CMTTool,
DriveWindow 1.x and DriveWindow 2.1

© ABB Group
May 13, 2013 | Slide 6
DCS800-R Upgrade Kits
Conditions caused by the application
 In case of an additional application three scenarios are possible
 Application program located in the APC1 or APC2 of a DCV 700.
 APC1: No interface available
 APC2: Optical connection board YPQ112 is to add between APC2 and SDCS-COM-
81 and control logic is to modify
 The application program is as function blocks in the DCS 500 or DCS 500B.  DriveAP
Programmimg or CoDeSys Programming
 The application program is located in the AMC board of a DCS 600 see APPLIC NAME
(4.03)  CoDeSys Programming

 Master-follower configurations
 Master-follower via SDCS-COM-8 should be used for upgrading a DCS 600. The fiber
optic cable can be reused.
 Master-follower via DCSLink should be used for upgrading a DCS 500 or DCS 500B.

 Hard-Parallel configuration
 Additional engineering is needed. Please contact your local ABB .
© ABB Group
May 13, 2013 | Slide 7
DCS800-R Upgrade Kits
Upgrade size A5 to D5
Article Codes
DCS800-R00-9305
DCS800-R00-9306 (with field exciter)
Included parts
 SDCS-POW-4
 FEX-425-Int (only DCS800-R00-9306)
 electronic tray
 SDCS-CON-4 with SDCS-DSL-4
 covers
 DCS800 Control Panel
 SDCS-PIN-51
 all boards are coated
Affected modules:
Converter type DCS 500B Converter type DCS 600
DCS50xB0903-y1 DCS60x-0903-y1
DCS50xB1203-y1 DCS60x-1203-y1
DCS50xB1503-y1 DCS60x-1503-y1
DCS50xB2003-y1 DCS60x-2003-y1
© ABB Group
May 13, 2013 | Slide 8
DCS800-R Upgrade Kits
Upgrade size A6/A7 to D6/D7
Article Code
DCS800-R00-9405
Included parts
 SDCS-POW-4
 electronic tray
 SDCS-CON-4 with SDCS-DSL-4
 SDCS-PIN-51
 covers
 DCS800 Control Panel
 all boards are coated
Affected modules:
Converter type DCS 500B Converter type DCS 600
DCS50xB1903-y1 DCS60x-1903-y1
DCS50xB2053-y1 DCS60x-2053-y1
DCS50xB2503-y1 DCS60x-2503-y1
DCS50xB3003-y1 DCS60x-3003-y1
DCS50xB2053-y1 DCS60x-2053-y1
DCS50xB2603-y1 DCS60x-2603-y1
DCS50xB3203-y1 DCS60x-3203-y1
DCS50xB3303-y1 DCS60x-3303-y1
DCS50xB4003-y1 DCS60x-4003-y1
© ABB Group
DCS50xB4803-y1 DCS60x-4803-y1
May 13, 2013 | Slide 9 DCS50xB5203-y1 DCS50x-5203-y1
DCS800-R Upgrade Kits
Upgrade size C2b to D5
Article Code
DCS800-R00-9005
Included parts
 SDCS-POW-4
 electronic tray
 SDCS-CON-4 with SDCS-DSL-4
 covers
 DCS800 Control Panel
 all boards are coated
Affected modules:
Converter type DCS 500B Converter type DCS 600
DCS50x-0680-y1 DCS60x-0680-y1
DCS50x-0820-y1 DCS60x-0820-y1
DCS50x-1000-y1 DCS60x-1000-y1

© ABB Group
May 13, 2013 | Slide 10
DCS800-R Upgrade Kits
Upgrade size C3 to D6
Article Code
DCS800-R00-9205
Included parts
 SDCS-POW-4
 electronic tray
 SDCS-CON-4 with SDCS-DSL-4
 SDCS-PIN-51
 covers
 DCS800 Control Panel
 all boards are coated
Affected modules:
Converter type DCS 500B Converter type DCS 600
DCS50xB0900-y1 DCS60x-0900-y1
DCS50xB1200-y1 DCS60x-1200-y1
DCS50xB1500-y1 DCS60x-1500-y1
DCS50xB2000-y1 DCS60x-2000-y1

© ABB Group
May 13, 2013 | Slide 11
DCS800-R Upgrade Kits
Upgrade size C4 to D7
Article Code
DCS800-R00-9105
Included parts
 SDCS-POW-4
 electronic tray
 SDCS-CON-4 with SDCS-DSL-4
 SDCS-PIN-51
 covers
 DCS800 Control Panel
 all boards are coated
Affected modules:
Converter type DCS 500B Converter type DCS 600
DCS50xB2050-y1 DCS60x-2050-y1
DCS50xB2500-y1 DCS60x-2500-y1
DCS50xB2650-y1 DCS60x-2650-y1
DCS50xB3200-y1 DCS60x-3200-y1
DCS50xB3300-y1 DCS60x-3300-y1
DCS50xB4000-y1 DCS60x-4000-y1
DCS50xB4750-y1 DCS60x-4750-y1
DCS50xB5150-y1 DCS50x-5150-y1
© ABB Group
May 13, 2013 | Slide 12
DCS800-R Upgrade Kits
Overview Parts Upgrade Kit

© ABB Group
May 13, 2013 | Slide 13
DCS800-R Upgrade Kits
DCV700 System Structure

For the communication

with overriding control
system additional
interface devices are to SDCS-POW-1 is to
implement. be replaced by
See next slides SDCS-POW-4

For drive diagnostic

SDCS-COM-81 with To be replaced by a new
DriveWindow is to use field exciter like:
DCF503B, DCF803,
FEX4-Int

For Master-Follower
communication DCS-Link via
DCS-DSL-4 or DDCS via
SDCS-COM-81 are to use

SDCS-CON-1 board is to In case of frame size C3

replace by SDCS-CON-4 the existing SDCS-PIN-
including SDCS-COM-81, 51 is to be replaced by
SDCS-DSL-4 and panel a new SDCS-PIN-51

© ABB Group
May 13, 2013 | Slide 14
DCS800-R Upgrade Kits
How to connect existing control system to SDCS-CON-4 (1/3)
Extension of APC2 controller with a DDCS interface adapter.

New interface board YPQ112B to

install into the existing APC rack.

YPQ112B
DDCS
Interface

Fiber
optic
link

Not more in
use. Can be
SDCS-COM-81 removed.
SDCS-DSL-4

SDCS-CON-4
Please note:
Installation of the YPQ112B interface adapter requires small modifications in the APC control program.
Availability of the right software tools and programming skills for APC controller are to ensure.

© ABB Group
May 13, 2013 | Slide 15
DCS800-R Upgrade Kits
How to connect existing control system to SDCS-CON-4 (2/3)
Removal of APC2 and direct connection to the overriding system via AF100 (MB90)
= Advant Fieldbus (AF100)
CI810B
Interface
DDCS / Advant
Fieldbus TB810

AF100 communication
interface kit NAFA-01
consisting of:
CI810 + TC505 +
TB810/TB811 Fiber
optic
link

Not more in
SDCS-COM-81 SDCS-DSL-4 use. Can be
removed.
SDCS-CON-4
Please note:
Installation of the CI810B communication interface requires small modifications in the overriding control
system e.g. AC450. Furthermore the removal of the APC controller requires adaption of the existing APC
software program either into the overriding system or into the drive via DriveAP or CoDeSys. Availability of
the right software tools and programming skills are to ensure.
© ABB Group
May 13, 2013 | Slide 16
DCS800-R Upgrade Kits
How to connect existing control system to SDCS-CON-4 (3/3)
Removal of APC2 and direct connection to the overriding system via MFB (MasterFieldbus)

PE1354B = Master FieldBus

MFB-Modulebus
converter

New fieldbus converter

PE1345B for Master
Fieldbus is to install and
to connect.
Fiber
optic
link

Not more in
SDCS-COM-81 SDCS-DSL-4 use. Can be
removed.
SDCS-CON-4
Please note:
Installation of the PE1354B fieldbus converter requires small modifications in the overriding control system
e.g. MP200. Furthermore the removal of the APC controller requires adaption of the existing APC software
program either into the overriding system or into the drive via DriveAP or CoDeSys. Availability of the right
software tools and programming skills are to ensure.
© ABB Group
May 13, 2013 | Slide 17
DCS800-R Upgrade Kits
Upgrade Kits - Additional Information
 Manual with detailed information
 For further information regarding hardware, assembling and commissioning see Manual
3ADW00256R0101
 Parameter settings
 After upgrading parameters have to be adjusted due to different parameter groups in
DCS500/DCS600 and DCS800.
 For parameter comparison see document 3ADW000405R0201
 Sales Chanel
 Product Sales and PartsOnline

© ABB Group
May 13, 2013 | Slide 18