TB 200

TELEBELT ® TB 200  |   MOBILE TELESCOPIC BELT CONVEYOR

1
A NEW STANDARD OF INNOVATION AND EXCELLENCE

TELEBELT TB 200 HIGHLIGHTS

The Telebelt® TB 200 is a technologically advanced, feature-rich The Telebelt TB 200 In Action at the Panama Canal
telescopic belt conveyor offering superior boom and feeder control
for precision placement. The TB 200 offers a rugged design to The first TB 200 arrived at the Panama Canal Third Set of Locks
perform at its peak under the harshest of conditions. project in fall 2012. This unit has been working at the Third Set
of Locks, a massive expansion project in which a hard-wearing
Ideal for large aggregate and mass concrete placement, the TB 200 concrete mix is being placed 24 hours a day. With a reach of
adapts for use in variety of applications, including concrete dams, 200 feet, belt width of 24 inches and high placing capacity, it is
hydro and nuclear power plants, harbors, airports and high-speed being used to place all types of concrete, reaching into hard to
train construction. reach lifts that are very often between form work and reinforcing
steel required by the very complex structures being built at the
Offering superior working range, maneuverability and shipping Panama Canal.
convenience, as well as lower counterweight requirements, more
power options and fewer wear parts, the TB 200 earns its place on
the job site.

TELEBELT ADVANTAGE

3 4 5
PLACEMENT VERSATILITY SAVES TIME AND LABOR JOBSITE CONVENIENCE

Whether your challenge is a congested Telebelts can perform multiple tasks from a Setup and redeployment is fast and
construction site, muddy ground or the single location. Quick setup and tear down easy with fully proportional radio remote
need to convey from outdoors to an inside as well as the ability to place material at controls for the boom and feeder. The feed
point of placement, Telebelts are up for the high volumes enable you to complete more conveyor is easily fed on three sides by
job. Telebelt versatility helps you avoid the jobs with less manpower. Tedious tasks a surge hopper, ready mix truck or dump
extra cost of specialized equipment like once requiring multiple trips with other truck. Telebelts do not require priming,
front discharge or all-wheel drive equipment are eliminated. and all material can be run off the belts,
ready-mix trucks. eliminating waste.
 12

PUTZMEISTER | H ANDLING CONCRETE AND VARIOUS MATERIALS

TELEBELT TB 200 MEETS YOUR DEMANDING MATERIAL PLACEMENT NEEDS

The easy-to-operate Putzmeister Telebelt TB 200 is designed for Conveying allows for reduced cement and water content which yields
fast, efficient, accurate placement of concrete without concrete a stronger and more cost effective mix. Corps of Engineers and
segregation. Able to place different types of materials, even in tight Federal and State DOT testing proves that Telebelts do not segregate
quarters, this single piece of equipment can be easily moved around concrete, cause air entrainment or slump loss.
the job site to allow you to handle multiple tasks and countless
applications in various setups. The four-section, steel frame main Need to place large aggregate quickly? The TB 200 is the Telebelt
conveyor and feeder conveyor are both hydraulically run, so full for the job. Have large volumes of a single material to convey in a
control of all actions is available for the operator to adjust output to short amount of time? The TB 200 greatly reduces placing time. It is
best fit the requirements of the particular pour. It takes no more than the ideal machine to handle heavy-duty mass concrete placement
10 to 15 minutes to set the TB 200 from traveling to operation mode. needs over long duration placement periods. When using the
Able to slew 360 degrees, the feeder conveyor can be positioned Putzmeister Heavy Duty Jumbo Trough or Surgecrete, the contractor
to suit any tight job site layout requirements. The machine saves assures maximum optimization of placing and hauling capacity
time and labor with quick setup, high material volumes and precise which greatly improves the operating costs. The TB 200 will be up
material placement. No additives are needed and no priming or to virtually any job challenge.
special clean-up is required. One operator can control the entire
From commercial and industrial to civil and environmental, the
unit with simple radio remote control system.
placing possibilities with a TB 200 are limitless. The TB 200 is ideal
The TB 200 efficiently and economically conveys high volumes of a for a variety of jobs including hydroelectric dams, power plants and
multitude of concrete mixes, as well as sand, gravel, backfill and up high speed rail construction. These are just a few applications where
to 6-inch aggregate. a Telebelt is an invaluable asset.

CONVEYING VERSATILITY – HANDLES CONCRETE AND A WIDE RANGE OF DRY MIX MATERIALS
7 8 9 10 11 12 13 14

PERVIOUS ROLLER GRAVEL SAND FRACKING WOOD

CONCRETE COMPACTED SAND
CONCRETE
LARGE AGGREGATE CONCRETE
CONCRETE
T ELEBELT T B 2 0 0   |   TELESCOPIC BELT CONVEYOR STANDARD FEATURES

BOOM MATERIAL HANDLING

• 200' 0" (61.00m) horizontal reach • Handles the harshest mass concrete mix designs at any slump
• Four-section telescopic boom • Ideal for aggregates up to 6" (152mm)
• High strength tubular steel construction for all sections • No special mix requirements
• Two control levers to extend/retract all main and feeder boom sections • Places any type of flowable material
and counterweight
• Maintenance-free sealed roller bearings
OUTRIGGERS
• Quick telescoping operation
• Outriggers hydraulically extend out and down
• 360° hydraulic rotation
• Quick and easy setup in 10 to 15 minutes
• Sets up on solid or rough terrain
BOOM OPERATION AND CONTROL • Self-leveling chassis
• Main conveyor functions controlled by Modular Boom Control
(MBC) system
• Single-section maintenance without removing entire valve assembly POWER
• Ergonomic and lightweight standard proportional radio remote control • Powered by Deutz TCD2015V6 450 hp (330kW) diesel engine
• Independent belt speed control for main and feed conveyors • Direct drive hydraulic pumps
• Proportional remote control with 100' 0" (30m) cable • Fuel tank 265 gallons (1,000L)
• Manual control backup for all functions

COUNTERWEIGHT
MAIN CONVEYOR • Structural steel component
• 24" (610mm) 3-ply nylon cord vulcanized belt • Proportional movement
• Observed capacity of 5 yds3 per minute (4.00m3/min) • Shaped design for increased clearance
• Infinitely variable belt speed control
• Spring-tensioned carbide scraper system
CLEAN UP
• Active independent control of the main conveyor system
• Simple water clean up
• High pressure 2,500 psi (173 bar) hydraulically-driven pressure
FEEDER BELT washer system
• 72' 6" (22.10m) steel hydraulic feed conveyor • Large capacity 105 gallon (400L) water tank
• 24" (610mm) 3-ply nylon cord vulcanized belt
• 360° hydraulic rotation allows material to be loaded from any position ADDITIONAL STANDARD FEATURES
• Fed by a surge hopper. Other options include ready mix truck, dump • 2 mph (3kph) job site travel speed
truck, skid-steer loader or front-end loader.
• 50 mph (80kph) road travel speed
• UHMW folding hopper handles the toughest mixes
• Transfer chute
• Spring-tensioned carbide scraper system
• Two service platforms
• Proportional hydraulic raise/lower and slew control
• High quality paint finish
• Active independent control of the feed conveyor system
• Operators manuals and ship-away kit
TRUNK/END HOSE
• 12" (305mm) reducer and end hose for precision placing
• 16" (406mm) reducer and end hose for large aggregate, high volume
• 15' (4.57m) standard end hose length
P U T ZMEI S T ER  | T ELEBELT TB 200 ADVANTAGE

15 16 17
HIGH STRENGTH BOOM STEEL COUNTERWEIGHT STEERING VERSATILITY

Four-section boom retracts to 74' 9" (22.80m), The TB 200’s steel counterweight is a structural Steering of the TB 200 has been engineered to
providing an expansive working range. Infinitely component of the unit. The counterweight moves provide a tight turning radius for necessary job
variable belt speed control through radio remote proportionally in and out as the boom extends site maneuverability. It features all-wheel steer,
offers smooth and controlled movement. The and retracts, ensuring that the right amount eight wheel drive, and a self-leveling chassis.
advanced boom design with modern lattice of weight is in the right position to offset the Steering modes are: on-road, all-wheel, crab
structure made of extruded steel tubes is load of the boom. Its lighter counterweight steer, reduced sheer, and independent rear
extremely strong, yet lightweight. requirement decreases the weight on each axle, axle mode.
providing greater efficiency.

18 19 20
SUPERIOR BRAKING SAFETY INTERLOCKS SHIPPING CONVENIENCE

Recognizing the importance of being able to Safety is engineered into the TB 200, with Able to be shipped globally for any project,
safely stop heavy machinery, especially in multiple safety interlocks that prevent improper the TB 200 is transported in the following four
rough conditions, the TB 200’s superior braking operation, including driving the unit with main components: the chassis – which can
system offers four types of braking: parking, the boom not properly stowed, running the be self driven and shipped RO/RO, the boom
service, engine, and transmission. Testing Telebelt when outriggers are not fully deployed, and feeder package – which is shipped break
demonstrates that the TB 200 can effortlessly and operating the Telebelt with an incorrect bulk, and two ocean containers – one for the
handle grades, as well as stop and re-start counterweight position. counterweight and one for the work platforms,
on them. feeder slewing gear and ancillary items.
 TELEBELT TB 200 SPECIFICATIONS

Conveyors
28' 10"
(8.80m)
Conveyor horizontal reach
Maximum at 0° 200' 0" (61.00m)
12' 9"
(3.90m) Maximum at 30° 174' 7" (53.20m)
Conveyor belt width 24" (610mm)
58' 5"
(17.80m)
27' 7"
(8.40m)
25' 3"
(7.70m)
Feed conveyor length 72' 6" (22.10m)
111' 3"
(33.90m) Feed conveyor belt width 24" (610mm)
Trunk/end hose length 15' 0" (4.57m)
Discharge height from grade
Maximum at 30° 114' 0" (34.70m)
Maximum at -15° -37' 5" (-11.40m)
Main & feed conveyors
Observed capacity at 0° 5.00 yd3/min (4.00m3/min)
Observed capacity at 20° 3.00 yd3/min (2.00m3/min)
30˚ Outriggers
114' 0" Outrigger spread L - R — front and rear 27' 3" (8.30m)
(34.70m)
hydraulic extended out/down
Outrigger spread front to rear 29' 2" (8.90m)
Engine Specifications
Manufacturer's Model Deutz TCD2015V6
Horsepower 450 hp (330kW)
Fuel tank capacity 265 gal (1,000L)
-15˚ General Specifications
-37' 5" Feed conveyor operating zone 360°
(-11.40m)
Main conveyor operating zone 360°
Water tank capacity 105 gal (400L)
200' 0" Horizontal Net Reach
(61.00m) Hydraulic oil tank capacity 105 gal (400L)
with cooler

WEIGHTS•+

Total weight 237,220 lbs (107,600kg)

180º Area Coverage
5,900 yd2 (4930m2)
Component Shipping Weights
Chassis 102,735 lbs (46,600kg)
Boom and feeder 61,730 lbs (28,000kg)
Shipping container #1 62,611 lbs (28,400kg)
Counterweight
Shipping container #2 42,000 lbs (19,000kg)
Work platform, hand rails, feeder slewing gear
R 78' 9" (24.00m)
29' 2" Maximum theoretical values listed.
(8.90m)
Right to make technical amendments reserved.
200' 0" (61.00m) •  Weights are approximate.
Main Conveyor +  All specifications apply to units mounted on Leibherr LTM 1220-5 2.
27' 3"
(8.30m)
12' 5"
(3.80m)
R
20

72' 6" (22.10m)

0'

Feed Center Line

0"
(6

Conveyor Rotation
1.0
0m
)

360º Operation Zone

for Main and Feed Conveyors

Photos and drawings are for illustrative purposes only. Authorized Distributor

Putzmeister America, Inc. Phone (262) 886-3200

1733 90th Street Toll-free (800) 884-7210
Sturtevant, WI 53177 USA Fax (262) 884-6338

PutzmeisterAmerica.com [email protected]
TB 4247 US © Putzmeister America, Inc. 2013 Printed in the USA (1.51304)