Scribd
Upload
49 views3 pages

CW1 Report

This 3 sentence summary provides the key details about the coursework document: The document outlines the coursework requirements for the Computer Aided Design 2 course, which requires students to conduct optimization and sensitivity analysis of a mechanical assembly using CAD tools to minimize weight under varying loads. Students must develop a 3D model of an assembly with over 3 parts, perform static and fluid flow analysis, and conduct local and global sensitivity analysis to optimize critical components and satisfy stress criteria. The coursework will be assessed based on a 2000 word report submitted online by December 2nd, 2021 discussing the design, analysis, and optimization of a selected mechanical assembly.

Uploaded by

Mohammad Azem
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
49 views3 pages

CW1 Report

This 3 sentence summary provides the key details about the coursework document: The document outlines the coursework requirements for the Computer Aided Design 2 course, which requires students to conduct optimization and sensitivity analysis of a mechanical assembly using CAD tools to minimize weight under varying loads. Students must develop a 3D model of an assembly with over 3 parts, perform static and fluid flow analysis, and conduct local and global sensitivity analysis to optimize critical components and satisfy stress criteria. The coursework will be assessed based on a 2000 word report submitted online by December 2nd, 2021 discussing the design, analysis, and optimization of a selected mechanical assembly.

Uploaded by

Mohammad Azem
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

F/QAP/021/004

College of Engineering
Course Work

Name of the programme BEng (GCU) /CAME


Name of Course with Code Computer Aided Design 2 – MHH324749
Level/ Semester & AY 4/A – 2021-22
Name of the Course Dr.Pradeep kumar Krishnan
Coordinator/Tutor Dr.Sureshbabu
Ms. Raiya Ali Said Al Hajri

Coursework type Case Study report of 2000 words


Assessment weightage 50 %
Type and date of submission On line report submission -2nd Dec 2021

Aim The aim of the Course work is to carryout Optimization and


sensitivity analysis using CAD tools for a mechanical
oriented assembly in order to adjust the weight of the
critical part / assembly under varying loading conditions.
Learning Outcomes • Model an engineering system as an assembly and
conduct analysis of the assembly for static analysis based
on Von Misses criteria.
• Conduct global and local sensitivity studies and perform
optimization study of the selected engineering
components to get optimized results for the selected
assembly.
• Conduct fluid flow analysis involving laminar and
turbulent flow.

Task(s)

Background of the problem

A mechanical system is under static load that enable the assembly to reach to its elastic state.
Considering the constraint, design the assembly established on optimization in order to adjust the
weight while considering appropriate factor of safety, material selection satisfying Von Misses
stress criteria. Each student is expected to address the following conditions:
 Developing the 3D model using CAD tools (PRO-E / PTC CREO) of the assembly that
contains more than three standard engineering parts;
 Optimizing the design of the assembly of the identified critical parts.

Rev: 01 Template B 9th July 2017 1|P a g e


F/QAP/021/004

Assessment Methodology

The student needs to submit the report on the design and analysis of the selected mechanical
assembly and discussing all the essential requirements. The assessment contains the following
task as shown in the assessment methodology:

Every experiment may be marked according to the following:

Report

Task No Description Weightage


Explain the concept of optimization in a
1 mechanical structure based on sensitivity 15%
analysis.
Develop the parts and assembly satisfying
2 20%
the constraints.

3 Static Analysis with justifications 20%

Local sensitivity analysis with justification


4 15%
minimum for two critical dimensions
Global sensitivity analysis for the critical
5 15%
component with justifications.
Optimization of the component in relation to
6 15%
the assembly selected with justifications.

Total 100%

Marking Scheme

Type of Assessment Description Weightage


Report based on optimization
Course Work 100%
study
Total 100%

Word limit minimum 2000 words.

Instructions

1. Plagiarism is a serious offence. In case of any plagiarism detected, penalty will be imposed
leading to zero mark. Policy and guidelines for dealing with plagiarism and malpractice in
examination can be viewed by clicking:
http://coeportal.nu.edu.om/member/contentdetails.aspx?id=490
Rev: 01 Template B 9th July 2017 2|P a g e
F/QAP/021/004

2. Course work should be submitted on time. College guidelines on late submission of


coursework can be viewed by clicking:
http://coeportal.nu.edu.om/member/contentdetails.aspx?id=565
3. Course work should be submitted with an appropriate cover page with all details clearly
and legibly filled.
4. For online submission of course work, a pdf file with appropriate cover page mentioning
name of student, student number and title of the course work should be uploaded using
the submission link created and made available by the course coordinator.

Referencing

Harvard Referencing (CCE Style) First Edition 2013 should be followed for both in-text and listing
references. This downloadable document can be found in our COE portal at:
http://coeportal.nu.edu.om/member/contentdetails.aspx?cid=628

Name and Signature of the Course Coordinator

Pradeep kumar Krishnan Date: 05 Sep 2021

Rev: 01 Template B 9th July 2017 3|P a g e

You might also like