Scribd
Upload
49 views

LTE Basic Parameters

LTE uses OFDM in the downlink and SC-FDMA in the uplink to support wide channel bandwidths from 1.4MHz to 20MHz. It supports high peak data rates of up to 300Mbps in the downlink and 75Mbps in the uplink. Key technologies include MIMO, advanced channel coding, and flexible frequency reuse. LTE is designed to provide low latency, high throughput, and seamless connectivity for high mobility applications.

Uploaded by

Vishwa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
49 views

LTE Basic Parameters

LTE uses OFDM in the downlink and SC-FDMA in the uplink to support wide channel bandwidths from 1.4MHz to 20MHz. It supports high peak data rates of up to 300Mbps in the downlink and 75Mbps in the uplink. Key technologies include MIMO, advanced channel coding, and flexible frequency reuse. LTE is designed to provide low latency, high throughput, and seamless connectivity for high mobility applications.

Uploaded by

Vishwa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

2/8/23, 5:06 PM LTE Basic Parameters

LTE Basic Parameters

This section will summarize the Basic parameters of the LTE:

https://www.tutorialspoint.com/lte/lte_basic_parameters.htm 1/3
2/8/23, 5:06 PM LTE Basic Parameters

Parameters Description

Frequency range UMTS FDD bands and TDD bands defined in 36.101(v860)
Table 5.5.1, given below

Duplexing FDD, TDD, half-duplex FDD

Channel coding Turbo code

Mobility 350 km/h

Channel Bandwidth (MHz)


1.4
3
5
10
15
20

Transmission Bandwidth
6
Configuration NRB : (1 resource
block = 180kHz in 1ms TTI ) 15
25
50
75
100

Modulation Schemes
UL: QPSK, 16QAM, 64QAM(optional)

DL: QPSK, 16QAM, 64QAM

Multiple Access Schemes


UL: SC-FDMA (Single Carrier Frequency Division Multiple
Access) supports 50Mbps+ (20MHz spectrum)

DL: OFDM (Orthogonal Frequency Division Multiple Access)


supports 100Mbps+ (20MHz spectrum)

Multi-Antenna Technology
UL: Multi-user collaborative MIMO

DL: TxAA, spatial multiplexing, CDD ,max 4x4 array

Peak data rate in LTE


UL: 75Mbps(20MHz bandwidth)

DL: 150Mbps(UE Category 4, 2x2 MIMO, 20MHz


bandwidth)

https://www.tutorialspoint.com/lte/lte_basic_parameters.htm 2/3
2/8/23, 5:06 PM LTE Basic Parameters

DL: 300Mbps(UE category 5, 4x4 MIMO, 20MHz


bandwidth)

MIMO UL: 1 x 2, 1 x 4

(Multiple Input Multiple DL: 2 x 2, 4 x 2, 4 x 4


Output)

Coverage 5 - 100km with slight degradation after 30km

QoS E2E QOS allowing prioritization of different class of service

Latency End-user latency < 10mS

E-UTRA Operating Bands


Following is the table for E-UTRA operating bands taken from LTE Sepecification 36.101(v860)
Table 5.5.1:

https://www.tutorialspoint.com/lte/lte_basic_parameters.htm 3/3

You might also like