Scribd
Upload
56 views

Consol Cosmetic

CONSOL COSMETIC is a two-component, polymer modified cementitious coating for concrete, mortar, and masonry substrates. It provides protection from deicing salts and improves waterproofing. The product has a natural grey color and is packaged in 20kg or 40kg sets. It requires mixing part A and B together before application with a brush, roller, or sprayer. Two coats are recommended with 2 hours between coats. Proper surface preparation is required before application. The coating increases substrate resistance to deicing salts and weathering.

Uploaded by

otong geyong
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
56 views

Consol Cosmetic

CONSOL COSMETIC is a two-component, polymer modified cementitious coating for concrete, mortar, and masonry substrates. It provides protection from deicing salts and improves waterproofing. The product has a natural grey color and is packaged in 20kg or 40kg sets. It requires mixing part A and B together before application with a brush, roller, or sprayer. Two coats are recommended with 2 hours between coats. Proper surface preparation is required before application. The coating increases substrate resistance to deicing salts and weathering.

Uploaded by

otong geyong
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TECHNICAL DATA SHEET

Version : 003
Update : January, 2020

CONSOL COSMETIC
Polymer Modified Portland Cement Coating

DESCRIPTION PRODUCT DATA


CONSOL COSMETIC is a polymer modified, 2 Form
component, cementitious coating. Designed for use on Part A : Powder
Part B : Liquid
concrete, mortar, and masonry substrates. Easily applied
by brush, roller, or spray equipment. This fine-textured,
Color
abrasion resistant coating is used for protection against Natural grey cement color
deicing salts and for damp-proofing/waterproofing.
Packaging
RECOMENDED FOR 20 kg set
CONSOL COSMETIC is used on: 40 kg set
• Use on grade, above, and below grade on concrete,
Storage
masonry, and mortar Dry, shaded place. Protect from direct sunlight and
• Use on horizontal, vertical, and overhead surfaces, frost.
both interior and exterior
• Use as a coating over newly repaired concrete to Shelf Life
provide a uniform appearance CONSOL COSMETIC can be stored for 12 months
• Use as a protective coating to reduce the effect of if stored as recommend in original unopened
deicing salt on concrete container.
• Use as a protective coating for waterproofing, damp-
proofing, and improved resistance to weathering TECHNICAL DATA
• Use on concrete and masonry substrates to improve Coverage
abrasion resistance to foot traffic and light Coverage is dependent upon substrate texture and
pneumatic-tire trafficmatic-tire traffic porosity
• Use to coat the backside of architectural curtain wall
panels to prevent water intrusion from the outside Tack-Free Time
• Portable water tanks. Approx. 30 minutes

BENEFITS Recoating Time


The other benefit of CONSOL COSMETIC are: Allow 2 hours minimum between coats
• Bond strength ensures superior adhesion
• Increases resistance of substrate to deicing salts Apllication Thickness
• Does not create a vapor barrier 0.2 - 0.4 mm/coat
• No mix water needed, liquid co-polymer triggers
special blend of cement, fillers, and admixtures Specific Gravity
• No batching, factory proportioned unit ensures Comp A : ~ 1.20 natural grey powder
consist composition and high quality. Non- Comp B : ~ 1.02 milky white liquid
flammable, low odor
• Easily applied to clean, sound substrates Mixing Ratio
A:B=1:1
3. Coating 1
APPLICATION
Substrate
Concrete, mortar, and masonry

Surface Preparation
All surfaces to be coated must be clean, sound, and
saturated surface dry with no standing water at the time
of application.
Remove all dust, laitance, grease, oils, curing compounds,
waxes, impregnations, and other contaminants.
4. Coating 2
Mixing
All mixing must be done mechanically using a low-speed
drill (400-600 rpm). Place approximately a half component
A into a clean mixer container. While mixing, slowly add
all of component B and continue to mix until achieve a
uniform paste with no lumps. Be sure to scrape down
sides of the mixing container at the time. Add remainder o
component a and continue to mix until uniformly blended.

Application
CONSOL COSMETIC should be applied over properly
prepared surfaces with high-quality brushes, rollers or
“hopper-type” spray equipment. Surface should be
saturated surface dry prior to application. Two coats are
recommended for maximum performance. Recommended
thickness per coat is 0.2-0.4 mm. apply thoroughly mixed
coating generously with loaded brush or roller. Always
finish off with light strokes blending back into coated area
for uniform appearance. For application in direct sun or on
a hot substrate, pre-wet surface and allow surface water
to dissipate before coating.

1. Cleaning Concrete Surface LIMITATION


• Maximum thickness of application is 0.4
mm/coat, thicker application can result in
cracking
• Do not apply when rain is expected
• Minimum ambient and substrate temperature is
70C and rising at the time of application
• For spray application, coating must be screened
prior to loading of the spray hopper
• Coating may chalk and show watermarks due to
weathering
• For application where coating will be subjected to
2. Wet Concrete Surface immersion, three days cure is recommended
• Coating will slightly yellow with age and exposure
to UV light
• As with all cement based materials, avoid contact
with aluminum to prevent adverse chemical
reaction and possible product failure.

You might also like