Scribd
Upload
30 views2 pages

Catalogue Băng Keo Alberta 80 Semi

ALBERTA-80-SEMI is a self-amalgamating, semi-conducting EPR tape that wraps irregular shapes without heat or pressure. It has excellent resistance to water and ozone, is UV resistant, and minimizes corrosion. The tape is intended for applications that require bonding to insulating materials or providing shielding for cable joints and is supplied in an easy-to-handle tape form.

Uploaded by

Hà Trần Mạnh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
30 views2 pages

Catalogue Băng Keo Alberta 80 Semi

ALBERTA-80-SEMI is a self-amalgamating, semi-conducting EPR tape that wraps irregular shapes without heat or pressure. It has excellent resistance to water and ozone, is UV resistant, and minimizes corrosion. The tape is intended for applications that require bonding to insulating materials or providing shielding for cable joints and is supplied in an easy-to-handle tape form.

Uploaded by

Hà Trần Mạnh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ALBERTA-80-SEMI

Semi‐Conducting EPR Self‐Amalgamating Tape

www.canadianpowermfr.ca Page 1/2


DESCRIPTION - Void‐free, homogeneous wrapping without
the application of heat or pressure.
ALBERTA-80-SEMI is a semi‐conducting, - Excellent resistance to water and
self‐amalgamating EPR (Ethylene Propylene ozone.
Rubber) tape. Its colour is - UV resistant.
black. The product and interleave are - The tape has been formulated to
printed with the cautionary words semi‐ minimize corrosion potential.
conducting to distinguish the - The product is approved to EDF HN 26‐S‐
product from insulating tapes. 04.
- Meets specification UTE C 33‐011.
APPLICATIONS - Service temperature: –40°C to +100°C,
Overload temperature 120°C.
Semiconducting tape is a highly - Supplied in an easy to handle and apply
conformable, semi-conducting EPR (Ethylene tape form. The product is interleaved
Propylene Rubber) based high-voltage with a disposable printed plastic liner.
splicing tape. It elongates easily to
conform to irregular shapes and retains PRODUCT PROPERTIES
its conductivity when stretched.
Semiconducting tape is intended for the - Branding: Canadian Power Manufacturing
following applications: - ASTM D4325-20:
- To electrically round out high-voltage Thickness: 0.01-in., 0.02-in., 0.03-in.
connectors and to bond to insulating Length: 3-yd., 5-yd., 6-yd., 7-yd.
materials to minimize electrical stresses Width: 0.75-in., 1-in., 1.5-in., 2-in.
- Continue semi-conducting strand Tensile Strength: 929.76 psi
shielding found in solid dielectric Elongation at break point: 762%
(polyethylene, XLP, EPR, etc.) cables up Fusion: Pass
to 69kV. Volume Resistivity: 103 ohm-cm
- Provide shielding for cable joints on Heat Ageing (130ºC within 168h): Pass
solid dielectric insulated power cables Ozone Ageing: Pass
(shielded or concentric neutral) - ASTM D4388-20:
- Replace semi-conducting layer beneath Temperature Rate @ Normal: 90ºC
metallic shield of similar cables in case Temperature Rate @ Emergency: 130ºC
of damage (screening) Temperature Rate @ Short-Cricuit: 250ºC
- Maintain positive connection between Self-Adhesion: Pass IV series
concentric neutral semi-conducting jackets UV Ageing Resistance: Pass
of power cables and semi-conducting - ASTM ISO4892-2:
surfaces of plug-in units Xenon Ageing: Pass
- For ensuring the continuity of
conductor and core screens at cable joints RECOMMENDATIONS
in a variety of polymeric and elastomeric
insulated cables. Care should be taken to avoid direct
- For stress cone construction, where it contact between the tape and petroleum‐
provides the conducting layer. type solvents and oils. Oils may affect
- For smoothing electrical stresses on the electrical properties of the tape.
irregular shaped lugs and connectors. The rolls should be stored flat on their
- For smoothing electrical stresses in cut edges in the original packaging. The
joints, terminations, and overhead power product must be protected from dust, heat,
lines, reducing discharges and consequent moisture, direct sunlight and solvent
interference to local radio and telephone fumes. Storage temperature between +10°C
communications. and +30°C.
Under these conditions, the storage life
PRODUCT BENEFITS of the tape in a temperate climate will be
at least five years.
- Excellent physical and electrical
properties with a high degree of
stability.

www.canadianpowermfr.ca Page 2/2

You might also like