MODEL: PKUMUX

Rev.: 20101104

PKUMUX
PK
transponder
BYPASS

CHRYSLER 2ND GEN AND GM PASSKEY 3+

TYPE RF TRANSPONDER BYPASS
GM PASS- Key III Plus, bypass for vehicles equipped with the new style hybrid Passlock (resistance) and Passkey 3+
(transponder) type anti-theft system.
Chrysler transponder bypass kit for all 2nd generation encrypted Sentry key immobilizer. The PKUMUX also features an
extra output designed to activate the Chrysler MUX circuit. Compatible with the CHWFR for 2008+ Chrysler vehicles
equipped with laser style key.

TECHNICAL SUPPORT / INFORMATION

web resources:
www.xpresskit.com
www.xpressvip.com
www.directechs.com

† Buick, Cadillac, Chrysler, Chevrolet, Jeep, Suzuki, Saturn, Mitsubishi, Dodge, GM, Pontiac and Hummer are registered trademarks and property of their respective companies.

© 2010 Directed Electronics. All rights reserved.

 MODEL: PKUMUX
Rev.: 20101104

VEHICLE COMPATIBILITY CHART AND INSTALLATION TYPE

Because the PKUMUX is compatible with a large number of

vehicles, note that there are 3 different wiring diagrams. The
chart below will tell you by vehicle which wiring diagram to use.

Vehicle Years Vehicle Years

Buick 2010 2009 2008 2007 2006 2005 2004 2003 GMC 2010 2009 2008 2007 2006 2005 2004 2003
Enclave D D Acadia D D D
Lucerne D D D D Savana D D
Cadillac 2010 2009 2008 2007 2006 2005 2004 2003
Sierra D D D
CTS D D
Yukon D D D
DTS D D D D
Hummer 2010 2009 2008 2007 2006 2005 2004 2003
Escalade D D D
SRX D D D H2 C C
Chevrolet 2010 2009 2008 2007 2006 2005 2004 2003 Jeep 2010 2009 2008 2007 2006 2005 2004 2003
Avalanche D D D Commander A or B A or B A or B
Cobalt D D D D Compass A or B A or B A or B
Equinox D D D Grand Cherokee A or B
A or B A or B
Express Van D D Liberty A or B A or B A or B
A or B A or B
HHR D D D D Patriot A or B A or B A or B
Impala D D D D Wrangler A or B A or B A or B
Malibu D D D D D D D Mitsubishi 2010 2009 2008 2007
2006 2005 2004 2003
Malibu MAXX D D D D
Raider B B B
Monte Carlo D D
Pontiac 2010 2009 2008 2007
2006 2005 2004 2003
Silverado D D D
G5 / Pursuit D D D D
Suburban D D D
Tahoe D D D G6 D D D D D
Traverse C Solstice D D D D
Chrysler 2010 2009 2008 2007 2006 2005 2004 2003 Torrent D D D
300 / 300C A or B A or B A or B Saturn 2010 2009 2008 2007
2006 2005 2004 2003
Aspen A or B A or B A or B Aura D D D
Pacifica A or B A or B A or B A or B A or B A or B Outlook D D D
PTCruiser A or B A or B A or B A or B Sky D D D
Sebring Convertible A or B A or B A or B VUE D D
Sebring Sedan A or B A or B A or B Suzuki 2010 2009 2008 2007 2006 2005 2004 2003
Town & Country A or B A or B A or B A or B
XL7 D D D
Dodge 2010 2009 2008 2007 2006 2005 2004 2003
Avenger A or B A or B
Caliber A or B A or B A or B
Caravan A or B A or B A or B A or B
In the case of the Dodge RAM 2006-
Charger A or B A or B 2007 (diesel), refer to installation type “C”.
Dakota B B B A or B A or B
Durango B B B A A A
Grand Caravan A or B A or B A or B A or B
Magnum A or B A or B A or B
Nitro A or B A or B A or B
Ram 1500 pickup B B B
Ram 2500 pickup B B B
Ram 3500 pickup B B
Ram 4500 pickup B
Ram 5500 pickup B
Ram SRT-10 pickup B

p.2

© 2010 Directed Electronics. All rights reserved.

MODEL: PKUMUX
Rev.: 20101104

INSTALL “A”: CHRYSLER 2ND GENERATION

TRANSPONDER without MUX IGNITION SWITCH
- 3 or 5 turns of loop are required.
- You can program the transponder
only once.
- Do not install on metal surface.

Input Blue/White (-) To Ground When Running Output (status)

Remote starter
main system
Pink
Violet
12 PIN HARNESS

Light Green
Blue
Red/White
White/Violet
Violet/Black
White/Black
White/Red
Input Red Batt + 12v
Input Black Ground

+12VDC

p.3

© 2010 Directed Electronics. All rights reserved.

 - 3 or 5 turns of loop are required.
MODEL: PKUMUX

- You can program the transponder

only once.
- Do not install on metal surface.

BCM

Input Blue/White (-) To Ground When Running Output (status)

Pink (+) Ignition input
(+) Ignition
Violet (+) Starter input If there is no starter output in the vehicle, connect (+) Starter
Light Green this wire directly to the remote starter’s starter wire.
Blue (-) Disarm (-) Disarm
Red/White BCM
main system

White/Violet Data Output Chrysler (BCM side)

Remote starter

Violet/Black Data Input Chrysler (Connector side)

White/Black Cut

12 PIN HARNESS
White/Red
Input Red Batt + 12v
Input Black Ground
INSTALL “B”: CHRYSLER 2ND GENERATION

+12VDC
Output
Starter
Output
Ignition
Multiplex

5 1
TRANSPONDER with OEM ALARM and Multiplex ignition

Facing view
Rev.: 20101104

© 2010 Directed Electronics. All rights reserved.

p.4
 - 3 or 5 turns of loop are required.
MODEL: PKUMUX

- You can program the transponder

only once.
- Do not install on metal surface.

BCM

Input Blue/White (-) To Ground When Running Output (status)

Pink (+) Ignition input
(+) Ignition
Violet (+) Starter input If there is no starter output in the vehicle, connect (+) Starter
Light Green this wire directly to the remote starter’s starter wire.
Blue (-) Disarm (-) Disarm
Red/White BCM
main system

White/Violet Data Output Chrysler (BCM side)

Remote starter

Violet/Black Data Input Chrysler (Connector side)

White/Black Cut

12 PIN HARNESS
White/Red
Input Red Batt + 12v
Input Black Ground
INSTALL “C”: DODGE RAM 2006-2007 (DIESEL)

+12VDC
Output
Starter
Output
Ignition
Multiplex

86 87 85

87a
30 5 1
TRANSPONDER with OEM ALARM and Multiplex ignition

Facing view
Rev.: 20101104

© 2010 Directed Electronics. All rights reserved.

p.5
MODEL: PKUMUX
Rev.: 20101104

INSTALL A, B & C: PROGRAMMING MODE FOR CODED

CHRYSLER KEY with INTEGRATED REMOTE
For Durango 2004 built before 17/05/04
The PKUMUX is compatible with 2004 Dodge Durango. However, all Durango’s built prior to 5 / 17 / 2004 must get a
WCM module upgrade wich will correct a problem preventing the vehicle from learning additional keys. Chrysler is
correcting this issue only when a Durango owner requests a new transponder key. The PKUMUX must be programmed
as would an additional key. The WCM replacement part number is 56038675AS.

*You will need 2 valid keys

Note
A) Place the loop antenna ring around the vehicle's Move antenna loop as close to
ignition cylinder as shown. the front of the ignition cylinder

1 B) Plug the 2 pin loop antenna ring connector into the

2 pin connector of the module.
(factory receiver ring) as possible.

OFF
*If present, immediatly remove the screw on the back of factory remote as shown on illustration KEY#1
IGN

2 at step 6
Insert the first valid key into the ignition switch and turn it ON for at least 5 seconds, but no
longer than 15 seconds.
ON

OFF
KEY#1
IGN

3 Turn the ignition switch OFF and remove the first key.
ON

KEY#2

OFF
4 Within 5 seconds insert the second valid key and turn the ignition switch ON. IGN
ON

KEY#2

OFF
After 10 seconds a chime will sound and the security light will begin to flash in

5 the cluster (not on the module). Turn the ignition switch OFF and remove the
second key. Security
IGN
ON

6 Remove cover and PC board from factory remote

Within 20 seconds from step 5, jump the blue/white wire (ground when running
output (-) status) of the PKUMUX to ground.

Blue/White To ground

7
OFF

Then, insert key (with the PC board removed) to the ignition position for a
period of 10 sec, you will hear a chime, the light will turn on for 3 sec. Keep the IGN
key at this position for 5 sec. ON
OFF

8 Turn the key off and remove the key.

Remove the blue/white wire from ground and connect to (-) ground when running
(status) output from remote starter.
IGN
ON

9 Programming is now completed. You can close the

remote and re-install the screw.

p.6

© 2010 Directed Electronics. All rights reserved.

 Green or Black
Connector

- 3 or 5 turns of loop are required. 1 2 3 4 5 6

MODEL: PKUMUX

- You can program the transponder

only once.
- Do not install on metal surface.

Data

+12v
5v Ref.

Ignition

Constant
Accessory
(+) Ignition
BCM (+) Accessory
Input Blue/White (-) To Ground When Running Output (status)
Pink (+) Ignition input BCM

Violet (+) Starter input

Light Green 5v Ref GM
main system
Remote starter

Blue
Red/White BCM BCM

White/Violet
WITH THE GM PASS-KEY III PLUS

Violet/Black
White/Black Data Input GM
Cut

12 PIN HARNESS
White/Red Data Output GM
Input Red Batt + 12v
INSTALL “D”: GM VEHICLES EQUIPPED

Input Black Ground

BCM

+12VDC

TECH NOTE ON RESISTOR CODE:

The Resistor code wire shows 12V for key sense, 0V for accessory, 5V during ignition, and just under 4V during
crank. This is due to the ignition switch shorting a 1300 ohm resistor between the Resistor code & the 5v Reference
wires. This diagram keeps the vehicle from setting off codes. Although these codes do not bring up any lights on the
dash they are still stored into the computer of the vehicle. If a dealer hooks up a scan tool they will see this and will be
able to blame it on the remote start. For troubleshooting a vehicle that uses this diagram that will not remote start the
vehicle would only require bypass, ignition & accessory, and tach to crank the vehicle and start. Make sure you have
the ignition, and test the tach source. Do not try to remote start without wiring this diagram or those codes will be
stored into the vehicles computer.
Rev.: 20101104

© 2010 Directed Electronics. All rights reserved.

p.7
MODEL: PKUMUX
Rev.: 20101104

INSTALL D: VEHICLE WIRING REFERENCE CHART

Resistor Voltage Resistor Voltage
Model Year Ignition Model Year Ignition
Code Reference Code Reference
Buick GMC
Enclave 2008-2009 White White/Black Pink Acadia 2007-2009 White White/Black Pink
Lucerne 2006-2009 White White/Black Pink Savana 2008-2009 Pink White Pink
Cadillac Sierra 2007-2009 Pink/Black White Pink
CTS 2009 White White/Black Pink Yukon 2007-2009 Pink/Black White Pink
DTS 2006-2009 White White/Black Pink Hummer
Escalade 2007-2009 Pink/Black White Pink H2 2008-2009 Pink/Black White Pink
SRX 2007-2009 White White/Black Pink Pontiac
Chevrolet G5 / Pursuit 2007-2009 White White/Black Yellow
Avalanche 2007-2009 Pink/Black White Pink G6 2005-2009 White White/Black Pink
Cobalt 2006-2009 White White/Black Yellow Solstice 2006-2009 White White/Black Yellow
Equinox 2007-2009 White White/Black Pink Torrent 2007-2009 White White/Black Pink
Express Van 2008-2009 Pink White Pink Saturn
HHR 2006-2009 White White/Black Yellow Aura 2007-2009 White White/Black Pink
Impala 2006-2009 White White/Black Pink Outlook 2007-2009 White White/Black Pink
Malibu 2004-2010 White White/Black Pink Sky 2007-2009 White White/Black Yellow
Monte Carlo 2006-2007 White White/Black Pink VUE 2008-2009 White White/Black Pink
Silverado 2007-2009 Pink/Black White Pink Suzuki
Suburban 2007-2009 Pink/Black White Pink XL7 2007-2009 White White/Black Pink
Tahoe 2007-2009 Pink/Black White Pink

INSTALL D: TRANSPONDER PROGRAMMING

OFF
KEY
IGN

1 Insert a valid key into the ignition switch and turn it ON.
OFF ON

KEY
IGN

2 Turn the ignition switch OFF and remove the key. ON

3 Within 10 seconds, remote start the vehicle.

p.8

© 2010 Directed Electronics. All rights reserved.

MODEL: PKUMUX
Rev.: 20101104

LIMITED ONE-YEAR CONSUMER WARRANTY

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product,
Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable
reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be
defective in workmanship or material under normal use, provided the following conditions are met: the Part was
purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along
with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address,
telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary
to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service,
installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO
EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE
EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY
TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING
DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF
CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN
THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY
LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL
NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY
CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE.
NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO
REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of
incidental or consequential damages. This warranty gives you specific legal rights and you may also have other
rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create
for it any other obligation, promise, duty or obligation in connection with this Part.920-0007 07-06

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the
select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus
interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation.
The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to
assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement.
N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential
damages sustained in connection with this product and neither assumes nor authorizes any representative or other
person to assume for it any obligation or liability other than the replacement of this product only.

PROTECTED BY U.S. PATENTS: 5,719,551; 6,011,460 B1 *;6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1;
6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829
B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7 , 0 6 8 , 1 5 3 B 1 ;
7,205,679 B1; CDN. PATENT: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2 , 4 1 5 , 0 4 1 ;
2,420,947; 2,426,670; 2,454,089 EUROPEAN PATENT:1,053,128 PAT. PENDING: 2,291,306; MADE IN CANADA

p.9

© 2010 Directed Electronics. All rights reserved.