HEALTHCARE Enclosure

Imaging Services

Document No: DD+DIS110.09E

This number is needed for production line only:
F7.5158.8802.0 CR 35-X
Type 5158/100

CR 25.0
Type 5156/100/105

Installation Instructions for

Digitizer Software C25_3102

► Purpose of this Document

This enclosure is part of the digitizer software C25_3102

and provides the installation instructions.

► Referenced Documents

Document Title
DD+DIS112.09E CR 25.0 Type 5156/100 Up to SN < 6000
Service Bulletin:
Announcement of Digitizer Software C25_3102
DD+DIS111.09E CR 35-X Type 5158/100 and
CR 25.0 Type 5156/105 As of SN ≥ 6000
Service Bulletin:
Announcement of Digitizer Software C25_3102

NOTE:
Dispose the enclosure document after finishing your task
(observe the confidentiality note below).

CONFIDENTIALITY NOTE:
Use, dissemination, distribution or reproduction of this document by unauthorized personnel is not permitted and may be unlawful.
DOCUMENT CONTROL NOTE:
The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0
05-2009 printed in Germany Document Node ID: 27300476
Enclosure_e_template_v07
Agfa Company Confidential Copyright © 2009 Agfa HealthCare N.V.
DD+DIS110.09E Enclosure

► Manufacturer
Agfa HealthCare N.V.

Publisher
Agfa-Gevaert HealthCare GmbH
Tegernseer Landstraße 161
D - 81539 München
Germany
Copyright © 2009 Agfa HealthCare N.V.
All rights reserved.
Technical modifications reserved.
AGFA and the Agfa-Rhombus are trademarks of Agfa HealthCare N.V.

WARNING:
Improper operation or service activities may cause damage or injuries.

INSTRUCTION:
(1) Read the "Generic Safety Directions" document
(see MEDNET GSO => General Info => Agfa HealthCare => Publications =>
Service Manual) prior to attempting any operation, repair or maintenance task on
the equipment.
(2) Strictly observe all safety directions within the "Generic Safety Directions" and on
the product.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 2 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

LIST OF CONTENTS

1 APPLICATION RANGE OF DIGITIZER SOFTWARE C25_3102 ............................................4

2 PREREQUISITES FOR INSTALLATION .................................................................................4
3 INSTALLATION PROCEDURE VIA USB MEMORY STICK (CR 35-X TYPE 5158 / 100
AS OF SN ≥ 4000, CR 25.0 TYPE 5156 / 105 AS OF SN ≥ 6500) ..........................................6
3.1 Making USB Memory Stick ready for Installation......................................................................6

3.2 Creating a Backup with a USB Memory Stick...........................................................................7

3.3 Installation Procedure of C25_3102 with USB Memory Stick...................................................8

4 INSTALLATION VIA FLOPPY DISKS (CR 25.0 TYPE 5156 / 100 / 105 UP TO SN < 6500,
CR 35-X TYPE 5158 / 100 UP TO SN < 4000) ......................................................................13
4.1 Creating Installation Floppy Disks...........................................................................................13

4.2 Creating a Backup with a Floppy Disk ....................................................................................15

4.3 Installation Procedure of C25_3102 with Floppy Disks ..........................................................16

5 INSTALLATION OF C25_3102 LANGUAGE FILES...............................................................22

6 CONCLUDING THE INSTALLATION.....................................................................................23
7 VERIFICATION OF SUCCESSFUL INSTALLATION.............................................................23

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 3 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

1 Application Range of Digitizer Software C25_3102

Digitizer software C25_3102 can be used for the following CR applications:

• General Radiography (GenRad),
• Mammography (Mammo),
• General Radiography 50 µm (Extremities) and
• Full Leg – Full Spine (FLFS)

The software cannot be used for Radiotherapy applications.

NOTE:
The new software is upgradeable from every previous version of C25_xxxx* software.
XXXX = Version number of the software

2 Prerequisites for Installation

REQUIRED TOOLS:
• For installation via floppy disk
Applicable for:
CR 25.0 Type 5156 / 100 / 105 up to SN < 6500,
CR 35-X Type 5158 / 100 up to SN < 4000:
- 1 floppy disk for the backup of site specific data
- 7 floppy disks for the installation files
- Service PC with floppy disk drive

• For installation via USB Memory Stick

Applicable for:
CR 25.0 Type 5156 / 105 as of ≥ 6500,
CR 35-X Type 5158 / 100 as of SN ≥ 4000:
- Service PC with USB connector
- 1 USB Memory Stick with at least 15 MB free disk space

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 4 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

For the installation on a new hard disk you need additionally:

• CD-ROM with test images. For current version please refer to the
service documentation, chapter 3.2 Tools and auxiliary means.
• Service PC which is equipped with a terminal program.
• Serial cable (RS232) with Sub D plugs (commercially available,
see figure 1), to connect the service PC for data logging.

9 pins 25 pins

Figure 1

REQUIRED TIME:
• Approximately 30 minutes for the software upgrade via floppy discs
• Approximately 60 minutes for the installation via floppy disks on a
new hard disk or when corrupted files detected
• Approximately 10 minutes for the installation via USB Memory Stick
(software upgrade/new hard disk/reformatted hard disk)

NOTE:
Register this software installation in the local service management system as
modification, e.g. in SMS as “MOD”.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 5 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3 Installation Procedure via USB Memory Stick

(CR 35-X Type 5158 / 100 as of SN ≥ 4000,
CR 25.0 Type 5156 / 105 as of SN ≥ 6500)

Following steps are necessary to install software via USB Memory stick:

# Type of software installation Section

1 Preparing USB Memory Stick 3.1
2 Creating a backup 3.2
3 Installing Software 3.3

3.1 Making USB Memory Stick ready for Installation

(1) Download the Digitizer Software C25_3102 (File size approx. 8 MB) from:
• MEDNET GSO => Computed Radiography => CR Digitizer => CR 25.0 =>
Freeware => CR 25.0 - Software - Device Software - C25_3102
or
• MEDNET GSO => Computed Radiography => CR Digitizer => CR 35-X =>
Freeware => CR 35-X - Software - Device Software - C25_3102
(2) Extract all files from the downloaded zip file into a folder on the Service PC.
Among the extracted files is the zip file c25_3102.zip.
(3) Extract all files from c25_3102.zip with extraction mode <Extract to here>.
Folder C25_3102 including seven sub-folders is created automatically.
(4) Copy the folder C25_3102 to the USB Memory Stick. The created structure
shown in Figure 1 must be maintained (“Root” is the USB Memory Stick).

(Root) ─┬─ c25_3102 ─┬─ portex_installer_1

│ ├─ portex_installer_2
│ ├─ harddisk_formatter
│ ├─ disk1
│ ├─ disk2
│ ├─ disk3
│ └─ languages
└─ c25_<SerialNumber>.BAC
Figure 1

NOTE:
C25_<SerialNumber>.bac is optional, for the case, that a
backup has been made previously.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 6 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3.2 Creating a Backup with a USB Memory Stick

Before the software update:

Update your USB Memory Stick with the latest machine specific data.

For this, execute these actions:

(1) Switch on and wait until the digitizer shows ready screen.
(2) Open the right cover of the digitizer.
You need access to the cPCI rack USB port.

IMPORTANT:
The digitizer checks light incidence.
Following error message may appear on the screen of the digitizer:
Digitizer locked
RIGHT SIDE PANEL NOT CLOSED.
Close right side panel.
Code 24791

Figure 2

If this error message appears, lean the cover on the side of the device.
Then continue with next steps.

(3) Enter the Service menu on the digitizer keypad and select
<3 Save data> Æ <2 Machine specific data>.
(4) Follow the instructions on the digitizer display.

Result Backup on USB Memory Stick is created.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 7 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3.3 Installation Procedure of C25_3102 with USB Memory Stick

Following possibilities exist to install software via USB Memory stick:

# Type of software installation To be used in case Section

1 Via boot up (recommended) Digitizer is up and running. 3.3.1
2 Via service menu Digitizer is up and running. 3.3.2
3 Via boot up incl. formatting New hard disk has been installed 3.3.3
or corrupted files detected.

3.3.1 Installing Software C25_3102 via Boot up

(1) Switch off the digitizer.

(2) Insert the USB Memory Stick into the USB of the Service PC.
(3) Open a file manager on the Service PC.
(4) Click on the letter of the < USB Memory Stick >.
(5) Click on folder <c25_3102> on the USB Memory Stick.
(6) Double-click on <prepare_installation.cmd>.
(7) Unmount the USB Memory Stick and disconnect it from the Service PC.
(8) Plug the USB Memory Stick into the digitizer.
(9) Switch on the digitizer.
(10) Wait approximately 2 minutes. The digitizer installs the software (including
operating system “Portex” and language files) and restarts.
(11) Wait until the digitizer has started.
(12) Click <OK> in the screen “Confirm Installation…” at the digitizer display.

Result Software C25_3102 is installed. Continue with section 6.

NOTE:
If the installation fails, repeat installation with installation method like
“Installing Software C25_3102 on new Hard Disk” in section 3.3.3.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 8 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3.3.2 Installing Software C25_3102 via Service Menu

(1) Enter Service Menu.

(2) Go to <5 – INSTALL data> data and confirm with <OK>.
(3) Go to <1 – Software> and confirm with <OK>.
Following message appears:
“Please insert the storage medium or the first floppy C25_3102 and press <;>”.
(4) Plug the USB Memory Stick into the USB Port of the digitizer.
(5) Press <;> to confirm. The digitizer copies, extracts and installs the software.
Operating system “Portex” will not be installed.
(6) After a few moments the following message appears:
“Please remove the storage medium and press <;>”.
Remove the USB Memory Stick and press <;> to confirm.
(7) After a few moments the following message appears:
“To initialize the new SW a reset is necessary. Press <;> to reset now.”
Close the digitizer. The device will restart automatically.
(8) Wait until the digitizer has rebooted.
(9) Click <OK> in the screen “To Confirm this Installation press OK” at the digitizer
display. Message “new software detected” appears in the digitizer display.

(10) After a few moments the following message appears:

“Please insert the backup medium and press OK. “
Press <Cancel>, the backup has to be performed later.

Result Software C25_3102 is installed. Continue with section 5.

NOTE:
If the installation fails, repeat installation with installation method like
“Installing Software C25_3102 on new Hard Disk” in section 3.3.3.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 9 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3.3.3 Installing Software C25_3102 on new Hard Disk or when corrupted Files detected

(1) Switch off the digitizer.

(2) Insert the USB Memory Stick into the USB port of the Service PC.
(3) Open a file manager on the Service PC.
(4) Click on the letter of the <USB Memory Stick>.
(5) Click on folder <c25_3102> on the USB Memory Stick.
(6) Double-click on <prepare_formatting.cmd>.
(7) Unmount the USB Memory Stick and disconnect it from the Service PC.
(8) Disconnect the digitizer from the network.
This is necessary since a default IP-Address and hostname is configured.
(9) Switch on the digitizer.
(10) Connect your service PC to the RS232 port at the CPU-Board.
(11) Start the terminal program by opening Windows menu
Start / Programs / Accessories / Communication /
HyperTerminal.
(12) Create a new connection and select your serial port (e.g., COM1).
(13) Set terminal settings to baud rate 115200, Xon/Xoff, no parity, 8 bit, 1 stop bit.
(14) Press <ENTER>.
The digitizer prompt <shell> appears.
(15) Plug the USB Memory Stick into the digitizer.
(16) Switch off digitizer.
(17) Switch on digitizer.
(18) When asked about formatting the hard disk on the terminal, answer with yes.
(19) Wait until the digitizer has started.
(20) After a few moments the following message appears:
“Please remove the storage medium and press <;>”.
Press <;> to confirm.
(21) After a few moments the following message appears:
“To initialize the new SW a reset is necessary. Press <;> to reset now.”
Press <;> to confirm.
(22) Press <;> again to initialize the reset.
Wait till the digitizer has rebooted.
(23) Click <OK> in the screen “Confirm Installation…” at the digitizer display.
Message “new software detected” appears in the digitizer display.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 10 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3.3.3.1 Restoring Machine Specific Data

NOTE:
Without restoring the device-specific parameters, an operation of the digitizer is
impossible.

(1) Enter the Service menu on the digitizer keypad and select
<5 INSTALL data / 2 Machine specific data>.
(2) Follow the guidelines on the digitizer display.
Use the backup that was created with the previous software version before the
Hard Disk was replaced by a new Hard Disk or if corrupted files detected.

3.3.3.2 Restoring Test Images

(1) Restore the test image files from CD to the directory E:\testimg on the
digitizer. For current version please refer to the service documentation,
chapter 3.2 Tools and auxiliary means.
(2) Press the <Reset> switch on the CPU-Board.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 11 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

3.3.3.3 Installing CPF

NOTE:
Between restoring the backup and installing the CPF, a reset is necessary!

(1) Get the CPF file either from a previous backup or from the Processing Station.
Otherwise generate the CPF file with the QS, the VIPS or the CCM tool.
Please refer to the respective service documentation, chapter 3.2, for details.
(2) Enter the Service menu on the digitizer keypad and select
<5 INSTALL data> / <6 CPF-File>.
(3) Follow the instructions displayed on the digitizer display.
(4) Reconnect the digitizer to the network.
(5) Disconnect the service PC.
(6) Switch off and switch on the digitizer.
(7) Check if the digitizer performs its self test and afterwards changes
its state to Ready.

Result If digitizer changes its state to Ready.

(8) Proceed with section 6 Concluding the Installation.
Note: Language files will be installed automatically during software installation from
USB Memory Stick.
If the digitizer does not perform the self test, the software may not be installed
successfully. In this case perform again the installation according to:
Section 3.3.3 Installing Software C25_3102 on a new Hard Disk.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 12 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4 Installation via Floppy Disks

(CR 25.0 Type 5156 / 100 / 105 up to SN < 6500,
CR 35-X Type 5158 / 100 up to SN < 4000)

Following steps are necessary to install software via floppy disk:

# Type of software installation Reference

1 Preparing floppy disks. 4.1
2 Creating a backup. 4.2
3 Installing Software. 4.3

4.1 Creating Installation Floppy Disks

You can create installation floppy disks either using the wizard (see 4.1.1) or manually
(see 4.1.2).

4.1.1 Creating Installation Floppy Disks with the Wizard

(1) Download the Digitizer Software C25_3102 (File size approx. 8 MB) from:
MEDNET GSO => Computed Radiography => CR Digitizer => CR 25.0 =>
Freeware => CR 25.0 - Software - Device Software - C25_3102
(2) Extract all files from the downloaded zip file into a folder on the Service PC.
Among the extracted files is the zip file c25_3102.zip.
(3) Extract all files from c25_3102.zip with extraction mode <Extract to here>.
Folder C25_3102 including seven sub-folders is created automatically.
(4) Take 7 empty, formatted diskettes.
(5) Double-click on <Start.bat>. The copy process starts automatically.
(6) Insert an empty floppy disk and follow the instructions on the screen.
(7) When requested, remove floppy disk from the floppy disk drive and label it with the
corresponding floppy name, e.g. C253102_1_3 for the first disk of installation files
(for a filename overview refer to table 1 on next page).
(8) Follow the instructions and insert the next floppy disks.
When all 7 floppy disks were copied, the prompt will be closed automatically.
NOTE:
Check the number of floppies after finishing the copy process.
There must be 7 floppy disks.
Result The set of floppy disks for installation are labeled with the correct name and contain the
correct files for the installation.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 13 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.1.2 Creating Installation Floppy Disks manually

(1) Download the Digitizer Software C25_3102 (File size approx. 8 MB) from:
MEDNET GSO => Computed Radiography => CR Digitizer => CR 25.0 =>
Freeware => CR 25.0 - Software - Device Software - C25_3102
(2) Extract all files from the downloaded zip file into a folder on the Service PC.
Among the extracted files is the zip file C25_3102.zip.
(3) Extract all files from c25_3102.zip with extraction mode <Extract to here>.
Folder C25_3102 including seven sub-folders is created automatically.

Seven sub-folders: Corresponding floppy name:

C25_3102\disk1 C253102_1_3
C25_3102\disk2 C253102_2_3
C25_3102\disk3 C253102_3_3
C25_3102\harddisk formatter HDFORMAT
C25_3102\portex installer 1 PORTEX1
C25_3102\portex installer 2 PORTEX2
C25_3102\Languages C25L3102
Table 1

NOTE:
For each of these folders, a floppy disk with the corresponding floppy
name must be created. Follow the instructions below.

(4) Insert an empty floppy disk.

(5) Select the floppy disk drive entry (A:) in the file manager.
(6) Right-click the floppy disk drive entry and select Properties.
(7) Select tab General and enter the corresponding floppy name,
e.g. C253102_1_3 refer to table 1.
(8) Click <OK>.
(9) Copy the contents of the corresponding folder (e.g. C25_3102\disk1) from the
service PC to the floppy disk.
(10) Remove the floppy disk from the floppy disk drive and label it with the
corresponding floppy name, e.g. C253102_1_3.
(11) Repeat steps (4) to (10) for the other folders to create the floppy disks.
Every sub-folder of C25_3102 must be on an own floppy.

Result The set of floppy disks for installation are labeled with the correct name and contain the
correct files for the installation.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 14 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.2 Creating a Backup with a Floppy Disk

Before the software update:

Update your Backup floppy disk with the latest machine specific data.

For this, execute these actions:

(1) Switch on and wait until the digitizer shows ready screen.
(2) Open the right cover of the digitizer.
You need access to the cPCI rack floppy disk drive.

IMPORTANT:
The digitizer checks light incidence.
Following error message may appear on the screen of the digitizer:
Digitizer locked
RIGHT SIDE PANEL NOT CLOSED.
Close right side panel.
Code 24791

Figure 3

If this error message appears, lean the cover on the side of the device.
Then continue with next steps.

(3) Enter the Service menu on the digitizer keypad and select
<3 Save data> Æ <2 Machine specific data>.
(4) Follow the instructions on the digitizer display.

Result Backup on floppy disk is created.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 15 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.3 Installation Procedure of C25_3102 with Floppy Disks

NOTE:
During the installation from floppy disks the digitizer shows no status report.
It is necessary to wait after inserting of a floppy, until the LED of the digitizers
floppy disk drive stops flashing.

If you want to see the installation status during the software installation, connect
the Service PC via serial connection cable (RS232) to the digitizer. By using the
Hyper Terminal the several installation steps of the digitizer can be followed.

Following possibilities exist to install software via floppy disks:

# Type of software To be used in case Reference

installation
1 Via boot up Digitizer is up and running. 4.3.1
2 Via boot up incl. New hard disk has been installed 4.3.2
formatting or corrupted files detected.

4.3.1 Installing Software C25_3102 as Upgrade of an older Software Version

4.3.1.1 Install PORTEX1

(1) Insert the floppy disk labeled PORTEX1 into the floppy disk drive of the digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the control LED of the floppy disk drive is off.
(4) Remove the floppy disk.

4.3.1.2 Install PORTEX2

(1) Insert the floppy disk labeled PORTEX2 into the floppy disk drive of the digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the control LED of the floppy disk drive is off.
(4) Wait additionally 1 minute, to be sure that all files are unzipped.
(5) Remove the floppy disk.
NOTE:
Do not insert any other floppy disk!

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 16 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

(6) Press the <Reset> switch on the CPU-Board.

WAITING TIME:
Wait approx. 2 minutes.
The files of the Portex operating system are installed.

4.3.1.3 Install C253102_1_3

(1) Insert the floppy disk labeled C253102_1_3 into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the control LED of floppy disk drive is off.
(4) Remove the floppy disk.

4.3.1.4 Install C253102_2_3

(1) Insert the floppy disk labeled C253102_2_3 into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the control LED of floppy disk drive is off.
(4) Remove the floppy disk.

4.3.1.5 Install C253102_3_3

(1) Insert the floppy disk labeled C253102_3_3 into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the control LED of floppy disk drive is off.
(4) Wait additionally 1 minute, to be sure that all files are unzipped.
(5) Remove the floppy disk.
NOTE:
Do not insert any other floppy disk!
(6) Close the digitizer. The device will restart automatically.
(7) Check if the digitizer performs its self test and afterwards changes
its state to Ready.
NOTE:
If the installation fails, repeat installation with installation method like
“Installing Software C25_3102 on new Hard Disk”.
DOCUMENT CONTROL NOTE:
The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 17 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.3.2 Installing Software C25_3102 on new Hard Disk or when corrupted files detected

NOTE:
This procedure must be carried out only if the hard disk of the digitizer has been
replaced by a new one or if corrupted files detected on the hard disk.
In this case the hard disk must be formatted using the installation disk HDFORMAT.

(1) Disconnect the digitizer from the network.

This is necessary since a default IP-Address and hostname is configured.
(2) Connect your service PC to the RS232 port at the CPU-Board.
(3) Start the terminal program by opening Windows menu
Start / Programs / Accessories / Communication /
HyperTerminal.
(4) Create a new connection and select your serial port (e.g., COM1).
(5) Set terminal settings to 9600 baud, Xon/Xoff, no parity, 8 bit, 1 stop bit.
(6) Press <ENTER>.
The digitizer prompt shell> appears.

4.3.2.1 Install HDFORMAT

(1) Insert the floppy disk labeled HDFORMAT into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Confirm partitioning/formatting of the hard disk on your terminal with <y>.
(4) Wait until the system prompt is displayed on the terminal.
(5) Remove the floppy disk.

4.3.2.2 Install PORTEX2

(1) Insert the floppy disk labeled PORTEX2 into the floppy disk drive of the digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the system prompt is displayed on the terminal.
(4) Remove the floppy disk.
NOTE:
Do not insert any other floppy disk!

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 18 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.3.2.3 Install C25_3102_1_3

(1) Insert the floppy disk labeled C25_3102_1_3 into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the system prompt is displayed on the terminal.
(4) Wait additionally 1 minute, to be sure that all files are unzipped.
(5) Remove the floppy disk.

4.3.2.4 Install C25_3102_2_3

(1) Insert the floppy disk labeled C25_3102_2_3 into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the system prompt is displayed on the terminal.
(4) Remove the floppy disk.

4.3.2.5 Install C25_3102_3_3

(1) Insert the floppy disk labeled C25_3102_3_3 into the floppy disk drive of the
digitizer.
(2) Press the <Reset> switch on the CPU-Board.
(3) Wait until the system prompt is displayed on the terminal.
Wait additionally 1 minute, to be sure that all files are unzipped.
(4) Remove the floppy disk.
(5) Press the <Reset> switch on the CPU-Board.
(6) Wait until the system prompt is displayed on the terminal.
The system extracts the C25_3102 software.
(7) Switch off and then switch on the digitizer.
(8) Wait until the digitizer is ready.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 19 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.3.2.6 Restore Machine Specific Data

NOTE:
Without restoring the device-specific parameters, an operation of the digitizer is
impossible.

(1) Enter the Service menu on the digitizer keypad and select
<5 INSTALL data / 2 Machine specific data>.
(2) Follow the guidelines on the digitizer display.
Use the backup floppy disk that was created with the previous software version
before the Hard Disk was replaced by a new Hard Disk or if corrupted files
detected.

4.3.2.7 Restore Test Images

(1) Restore the test image files from CD to the directory E:\testimg on the
digitizer. For current version please refer to the service documentation,
chapter 3.2 Tools and auxiliary means.
(2) Press the <Reset> switch on the CPU-Board.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 20 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

4.3.2.8 Install CPF

NOTE:
Between restoring the backup and installing the CPF, a reset is necessary!

(1) Get the CPF file either from a previous backup or from the Processing Station.
Otherwise generate the CPF file with the QS, the VIPS or the CCM tool.
Please refer to the respective service documentation, chapter 3.2, for details.
(2) Enter the Service menu on the digitizer keypad and select
<5 INSTALL data> / <6 CPF-File>.
(3) Follow the instructions displayed on the digitizer display.
Have a floppy disk ready for the backup of device-specific parameters.
(4) Reconnect the digitizer to the network.
(5) Disconnect the service PC.
(6) Switch off and switch on the digitizer.
(7) Check if the digitizer performs its self test and afterwards changes
its state to Ready.

Result If digitizer changes its state to Ready:

(8) Software installation was successful.
Proceed with section 5 "Installation of C25_3102 Language Files".

If the digitizer does not perform the self test, the software may not be installed
successfully. This can be caused by a corruption of the file system on the Hard Disk.
In this case perform the installation according to:
Section 4.3.2 Installing Software C25_3102 on a new Hard Disk
and then section 5 Installation of C25_3102 Language Files.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 21 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

5 Installation of C25_3102 Language Files

NOTE:
With software version C25_3007 the term “floppy” has been exchanged with the term
“medium”.

To install C25_3102 language files and to change the language of the digitizer user
interface perform following procedure:

(1) Ensure that the digitizer is switched on.

(2) Open Service menu on the local key pad of the digitizer.
(3) Choose <5 INSTALL data>.
(4) Choose <7 Language Files>.
(5) Open right side cover.
(6) Insert medium with language data and choose <OK>.
(7) After a few moments the following message appears:
“Please remove the storage medium and press <;>”.
Remove the USB Memory Stick and press <;> to confirm.
(8) Following message appears in the Service menu:
<Do you want to change user interface language>
To change the user interface language press <;>.
To leave the menu without changing the language press <:>.
(9) Select user interface language from the list and press <;>.
(10) Exit Service menu by pressing <:> and <:>.
(11) When the system requests to confirm the changes press <;> and follow the
instructions on the screen.

Result Installation of C25_3102 language files completed. Continue with section 6.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 22 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential
DD+DIS110.09E Enclosure

6 Concluding the Installation

(1) Refresh your backup by following the guidelines of Service Menu

<3 Save data> / <2 Machine specific data>.
(2) Close the digitizer.

NOTE:
If you use the digitizer for Mammography applications, enable “Mammo” manually
in the Service Menu of the digitizer.

7 Verification of successful Installation

(1) Enter the Service menu on the digitizer keypad and select
<1 INFO> / <1 Device info>.

(2) Check the entry Software.

Result If the entry Software is C25_3102, the software installation was successful.
Otherwise repeat the installation.

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Revision 0 CR 35-X Type 5158/100 Page 23 of 23

05-2009 CR 25.0 Type 5156/100/105 Agfa Company Confidential