BITUMINOUS MEMBRANCE REINFORECED WITH (POLYESTER 200 gim*) MODIFIED WITH APP (ATACTIC POLY PROPYLENE) sR PROPERTIES UNIT VALUE TEST METHOD 1 Softening point °c 188 ASTM 036 2 Penetration dmm 20 ASTM D 5. 3 Cold Flexibility °c -5to-10 ASTM D 5147 4 Heat Resistance (@120°C for 2h: Pass No flow ASTM D 5147 5 Tensile strength @23 + 2°C Longitudinal N/Som 1100 (22kN/m) ASTM D 5147 Transversal 850 (17kN/m) 6 Tensile strength N/Scm @-18 +2°C N/Scm 1200 (24kKNim) ASTM D 8147 Longitudinal 950 (19 kN/m) Transversal 7 Elongation @23 + 2°C % ASTMD 5147 Longitudinal 50 Transversal 50 8 Elongation, % @-18+2°C % ASTM D 5147 Longitudinal 24 Transversal 26 9 Lap joint Strength NIS cm UEAte M.O.AT 30 Longitudinal 1100 Transversal 850 10 Tear Strength N ASTM D 5147 Longitudinal 600 Transversal 500 11 Puncture Resistance N 1155 ASTM E 154 Static \4 UEAte 5.1,9 Dynamic 4 UEAte 4.4.1 % Longitudinal >06 ASTM D 5147 Transversal > 06 13. Resistance to Aging (after 2000 hrs) No Deterioration ASTM D 4799 14 Water Absorption (@ 23°C for hrs) % <1 ASTM D 5147 15 Water Vapour Transmission, g/m2/24hes <05 ASTM E 96 16 Resistance to leakage at joints pass UEAte NOTE : THE ABOVE SHOWN TECHNICAL DATA ARE RESULTS OBTAINED IN LABORATORY AND EXTRA DETAILS CAN BE PROVIDED UPON REQUEST. IN ACCORDANCE TO ASTM AND UEAtc STANDARDS, RESULTS ARE SUBJECTED TO A VARIATION OF 20 % izomax VIA 200 3000 P4000 P5000 PE000izomaks wswsHi BITUMINOUS MEMER/ANCE REINFORCED WITH (POLYESTER 200 g/m’). MODIFIED WITH APP (ATACTIC POLYPROPYLENE) Waterproofing of road projects is much easier withizOmax via reinforced with polyester mat With is APP modified and iZomMAxX vinis a product is especially for construction projects that required high tensile strength itis resistant to temperature fifferences , ensures high endurance and provides ulmost protection against damages . As a highly fear resistant product, it can be used in all kinds of waterproofing applicaitions, ensuring high performance izomax viaprovides proection in exireme temperalures and the high quality polyester (200gr/m) used as a reinforoement helps the product to stick well tothe surface and function as protective layer APPLICATION AREAS - APP modifiediZOMAX viacan be used in all areas and projects with high tensile requirements that require waterproofing Such as bathrooms,pite capping footing , tanking , car parks , bridge decks , viaducts highways , abutments , tank lining swimming pools , airport aprons , ramp ~ areas and others APPLICATION = Installed by tarch welding method, loose = laid or fully bonded to substrate, When loose -laid nly overlaps are bonded together. Periph - eres ‘and protons are sea aocortng to specications 10 cm (4inches) overtopging shall be allowed for joints and 15 om (6 inches) overtopping forends by using welding torch - Mineral coated products may be used to protect the upper surface ifno covering planned - Resist splits and tears due to its pliability elongation characieristics izomax VIA P3000 P4000 P5000 P6000 STROAGE AND PRESERVING - Rolls shoud be instailed in an uproght Position on to the delivery vehicle and stored and carried indoors in the same way. - Should not be exposed to ultaviolet rays UV and to sudden changes of temperatures. - Rolls should be covered for protection from. UV rays if they are to be stored for a long period of time - No cutting or perfostion should be made after the application ~ It should not be exposed to UV rays after the application without mineral store cap sheet or protective coating. - Rolls should not be put one on top of another if stored without palettes - Maximum two rows should be put one top of another if stored with palettes. ADVANTAGES ~ Application to various types of substrates - The quantity to be used can bedetermined before the application. - It's reinforcement system has high tensile strength - Reinforcement with high elongation capability