0% found this document useful (0 votes)
62 views3 pages

FSpwMuniZ EN

The document describes a Z.Plex filter technology for municipal water pre-filtration. It provides specifications on materials, dimensions, performance and flow rate. It also details ordering information and certifications to ensure quality and safety.

Uploaded by

Franco Ynquilla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
62 views3 pages

FSpwMuniZ EN

The document describes a Z.Plex filter technology for municipal water pre-filtration. It provides specifications on materials, dimensions, performance and flow rate. It also details ordering information and certifications to ensure quality and safety.

Uploaded by

Franco Ynquilla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Muni.

Z*
FACT SHEET

Z.Plex* technology depth filter for municipal water


pre-filtration
Applications
• Municipal water systems pre-filtration
• Surface water prefiltration
• Ground water prefiltration
• General industrial use

Specifications
Table 1: Specifications and performance information

Ratings 1, 5 microns (nominal)


Inner Diameter 1 in (2.5 cm)
(Nominal)
Outer Diameter 2.46 in (6.2 cm)
29 1/4 in (74.3 cm)
30 in (76.2 cm)
Lengths
39 in (99.1 cm)
40 in (101.6 cm)
Longer lengths up to 70 in may be available upon request

Features and Benefits Materials of Construction


Filter Media Polypropylene
• Engineered specifically for municipal water
prefiltration and highly suitable for general Adapters Polypropylene
applications Buna, EPDM, Silicone, Viton1
Elastomer
• Graded density traps particles throughout Santoprene2 (flat gasket only)
• Lower initial pressure drop than conventional Performance Conditions
depth filters
Maximum pressure drop:
• Filter composition contains no resin binders, 35 psid (2.4 bar) @ 77°F (25°C)
lubricants, antistatic or release agents Recommended change-out pressure drop:
• Melt-bonded exterior ensure no media migration 20 psid (1.4 bar) @ 77°F (25°C)
• Provides lower total cost of filtration

WATER TECHNOLOGIES
Muni.Z

Efficiency Information Quality


Table 2: Removal efficiency based on a modified ASTM Muni.Z filters are manufactured under a quality
795 procedure management system that has been certified to meet
ISO 9001 standards. Each filter is assigned a lot code
Removal Rating (µm) to ensure traceability of the data and materials used
Micron at Various Efficiencies in the manufacturing process.
Rating
90.0% 99.0% 99.9%

Efficiency of nominal filters varies by


Certifications
1 µm
application. See note for information on nominal • U.S. FDA 21CFR 177.1520 food contact
5 µm filter efficiency3 requirements
• Article 3 of the EU Framework Regulation No.
1935/2004/EC safety requirements
lpm • EU Plastics Regulation No. 10/2011 (may be
0 5 10 15 used as intended in all compliant EU Member
states)
1 70 • USP class VI-121°C Plastics criteria
60 • NSF 61 criteria
Differential Pressure

0.8
50
• ISO 9001 criteria
mbar

0.6 40 Veolia filter cartridges are designed and


psi

manufactured for resistance to a wide range of


0.4 30
chemical solutions. Conditions will vary with each
20 application and users should carefully verify chemical
0.2 compatibility. Please contact your Veolia
10
representative for more information.
0 0
0 1 2 3 4 5
gpm Ordering Information
Clean Water Flow Rate
Replace the numbers with your desired values from
Graph 1: Muni.Z clean water flow rate based on a 10 in each column. Columns 3, 4, and 5 are optional
length filter depending on the desired configuration.

Example: Muni.Zs 01-40-ESS

Muni.Zs 1 - 2 - 3 4 5

2
Muni.Z

Table 3: Ordering information

1 2 3 4 5
Micron
Type Rating Cartridge Length End #1 Adapter End #2 Adapter Elastomer Material
(nominal)
Muni.Zs 01 = 1 µm 29 1/4 in (74.3 cm) E = 222 O-Ring H = Fin B = Buna
05 = 5 µm 30 in (76.2 cm) E = EPDM
39 in (99.1 cm) F = 226 O-Ring K = Self Seal Spring P = Santoprene2
40 in (101.6 cm) (flat gasket only)
S = Silicone
V = Viton1
Longer lengths up to L = Extended Core S = Solid End
70 in may be available
upon request X = Standard Plain X = Standard Plain
End (no gasket) End (no gasket)

Y = Flat Gasket Y = Flat gasket

1
Viton (trademark of The Chemours Company)

*Trademark of Veolia; may be registered in one or more countries. ©2022 Veolia. All rights reserved. FSpwMuniZ_EN.docx Jul-20
2
Santoprene (licensed to Advanced Elastomer Systems, L.P.)
3
Absolute-rated filters have been designed and tested to reject at least 99% of particles of the listed micron size. Nominal-rated filters have a wider
distribution of pore sizes and therefore a wider distribution of rejected particle sizes. The nominal rating is primarily used to compare efficiencies
across a filter family and between filter manufacturers. Efficiency is dependent on particle shape, size, composition, application, and testing protocol.

Veolia Water Technologies


Please contact us via:
www.veoliawatertechnologies.com 3

You might also like