CEILING FAN

Model : AX20-5B/56
AX20-5B/42
Version: 2020 V1
 TABLE OF CONTENT SAFETY PRECAUTION

Item Page No. CAUTION

1. Safety Precautions ............................................................................... 1 - 2 Please take note of the following important points when installing.

The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
2. Parts & Accessories .............................................................................. 3 sufficient strength to withstand 4 times the weight of the ceiling fan.

3. Installation Instruction ........................................................................... 4 - 8 The mounting of the suspension system shall be performed by the manufacturer, its service agent or
suitably qualified persons.
4. Transmitter Assembly & Function ......................................................... 8 - 9 The fan is to be installed so that the blades are more than 2.5m above the floor.

5. Power Supply Connection & Circuit Diagram ....................................... 9 - 10 Safety cord should not be longer than the earthing conductor.
Should failure of the suspension system occur, the supporting of the fan must not rely on the earthing
conductor. The earthing terminal in the fan assembly should be such that should any part of the suspen-
6. Maintenance ......................................................................................... 10 sion system fall off, the body of the fan assembly shall effectively earthed.

7. Technical Specifications ........................................................................ 11 Ensure that the unit’s panel is closed after service or installation.
Unsecured panels will cause the unit to operate noisily.
8. Customer Service Centre ...................................................................... 12 Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid from
being in contact with these places.

Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF”
SAFETY PRECAUTION position.
If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard to
service personnel or the user.
Warning
Do not operate any heating apparatus too close to the ceiling fan unit or use in room where mineral oil, oil
Installation and maintenance work shall only be performed by qualified persons, familiar with local code vapour or oil steam exist, this may cause plastic part to melt or deform as a result of excessive heat or
and regulation, and experienced with this type of appliance. chemical reaction.

All field wiring must be installed in accordance with the national wiring regulation. Ensure the colour of wires of the outdoor unit and the terminal markings are same to the indoors respec-
tively.
Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring
Don’t use joined and twisted wires for incoming power supply.
work according to the wiring diagram.
Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling fan.
The unit must be GROUNDED to prevent possible hazard due to insulation failure.
The earth wire is approximately 60mm longer than safety wire. This is to ensure at the event whereby the The fan suspension system and blade screw tightening shall be examined yearly.
suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent electro-
cution. Replacement of parts of the safety suspension system device shall be performed by the manufacturer, its
service agent or suitably qualified persons.
Tighten the blade firmly using a screw driver.
Blades that are detached from the unit during operation will cause serious injuries and property damages. Torque value for screw/bolts for securing primary suspension system for motor is 2Nm.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliances.

Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure that
the blade is fully static before doing any maintenance work.

STOP using the ceiling fan when any abnormality or failure occurs.
If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the
manufacturer, its service agent or suitably qualified persons.

1 2
 PARTS & ACCESSORIES INSTALLATION INSTRUCTION

Step 1 Step 3 - Remove the Bolt, Clevis Pin, Nut,

Assemble the Canopy and Coupling Cover through Washer and Rubber Pulley from the Downrod.
the Downrod. Place the Rubber Pulley onto the ceiling hook
and fix back the Bolt, Clevis Pin, Nut and
Washer.
IMPORTANT : Clevis Pin MUST be inserted to
Canopy prevent Nut from loosening.

Downrod
Motor Assembly Canopy Coupling Cover
Rubber
Pulley Clevis Pin
Nut
Coupling Washer
Cover
Bolt
Blade Panel x 5 Blade Holder x 5 Switch Housing Safety
Wire
with Receiver

Step 2
a) Route all the wires from the Motor through
the Downrod.
b) Fix the Downrod to the coupling with Bolt,
Washer, Nut and tighten them firmly then insert
the Clevis Pin.
Fan Blade x 5 Rubber Pulley Assembly Step 4 - Remove the Safety Wire screw and
with Downrod IMPORTANT : Clevis Pin MUST be inserted to spring washer from the Downrod.
prevent Nut from loosening.

Green/
Yellow (E)
Brown (L)
Blue (N)
Bolt, Washer, Nut Blade Panel Screw Blade Holder Screw
and Clevis Pin x 2 & Washer x 16 & Washer x 11 Safety Wire

Transmitter & Holder x 1

Battery x 2
AAA Washer & Nut
AAA Clevis Pin

Coupling

Clamp the downrod

with the 2 screws
on the coupling to
prevent shaking
during operation.

3 4
 INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION

Step 5 Step 7
Tie the Safety Wire across the hook as shown. Connect the wires from the fan to house’s supply wire.

House Supply Wire

Blue (N) Yellow/Green (E)

Brown (L)

Yellow/Green (E)
Blue (N)
Safety Wire
Brown (L)

Step 8
Align the 3 holes on the Blade Holder, Blade and Blade Panel and screw on with Blade Panel Screw and
In the case of “J” Hook is being used. Washer provided.

Step 6
Firmly screw the Safety Wire with spring washer onto the Downrod.

Blade Holder

Washer (Red Colour)

Blade

Blade Panel

5 6
 INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION

Step 9 Below shows a complete installation diagram.

Align the holes on the Blade Holder with Motor and screw on with the Blade Holder Screw and Washer
provided.

IMPORTANT : Assemble the Fan Blades only after the ceiling fan is mounted on the hook.

TRANSMITTER ASSEMBLY

1. Insert the 2 pcs of AAA battery (provided) into the Transmitter.

2. Mount the Transmitter Holder on the wall with the screws provided.

Transmitter

Step 10
Connect the connectors and twist the Switch Housing onto the Fitter Plate till snug.

Transmitter Holder

AAA
AAA
Fitter Plate

Switch Housing

7 8
 TRANSMITTER FUNCTION CIRCUIT DIAGRAM

IMPORTANT : DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO DIMMER

SWITCH OR REGULATOR.
Power
Turn off fan
Fan Speed
1 - Lowest speed
5 - Highest speed Thermal
Fuse
(Inside Motor Motor
Timer On Natural Wind Motor) Capacitor
Fan speed changes within To Fan L Brown Blue Grey Blue
1h - Fan turns on after 1 hour L
3h - Fan turns on after 3 hours its range creating gentle
6h - Fan turns on after 6 hours sea-breeze effect
Orange Yellow
8h - Fan turns on after 8 hours
Main
PCB
To Fan N Blue
N

Last Memory Function

The Transmitter & Receiver is incorporated with last memory function. It stores the last reading/setting on E
memory and when the fan is switch on again, the operation will be as the last memory/setting.

POWER SUPPLY CONNECTION

IMPORTANT : DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO DIMMER

MAINTENANCE
SWITCH OR REGULATOR.
Due to the fan’s natural movement, connections may get loose after period of usage. To ensure a proper
and safety usage, it is highly recommended to inspect and tighten all connections every 6 months.

Cleaning
Cleaning your fan periodically will prolong its new appearance. Basic cleaning procedures
are as follows :
1. Use only water and mild soap. Do not use solvents, corrosive or acidic solution.
2. Damp the cloth lightly. Use only soft or lint-free cloth to clean the fan. Rough fabric will
scratch the surface.
3. Do not bent the blades while cleaning. At the event where blades are bent or damage,
order new set of blades from service center or dealer shop.
4. There is no need to oil the fan.
Regulator Dimmer Switch

9 10
 TECHNICAL SPECIFICATIONS CUSTOMER SERVICE CENTRE

Model AX20-5B/56 AX20-5B/42 If you need any technical assistance or faulty report, please contact our customer service centre at :

No. of Blades 5 5 Alpha Home Appliances Sdn. Bhd. (390258-H)

Fan Width 56” 42” Head Office : 6, Jalan Sungai Kayu Ara 32/37, Berjaya Park, Section 32, 40460 Shah Alam, Selangor.
Motor RPM 90 - 205 145 - 280 Tel : 03-5740 6666 Fax : 03-5740 8220
Website : www.alphamalaysia.com Email : [email protected]
Voltage 220-240V~ 50Hz 220-240V~ 50Hz
Wattage 20W - 80W 21W - 70W Johor Bahru : 71, Jalan Molek 3/10, Taman Molek, 81100 Johor Bahru.
Tel : 07-353 4833 / 4933 Fax : 07-355 4233
Nett Weight 7.2kg 6.3kg
Melaka : 19, 19-1 & 19-2, Jalan KSB 11, Taman Kota Syahbandar, 75200 Melaka.
Tel : 06-292 6292 / 6293 Fax : 06-292 6296

Ipoh : 11, Laluan Tasek Timur 5, Pusat Perdagangan Tasek Indra, 31400 Ipoh, Perak.
Tel : 05-545 2282 / 547 2282 Fax : 05-547 6282

Penang : 28, Jalan Icon City, Icon City, 14000 Bukit Mentajam, Penang.
Tel : 04-506 2366 / 2066 / 2566 Fax : 04-506 2966
362mm 460mm
Pahang : A131, TK1, Jalan Wang Ah Jang, Taman Liza, 25100 Kuantan, Pahang.
(1’ 2”) (1’ 6”)
Tel : 09-516 5226 Fax : 09-513 9226
More than 1m

AX20-5B/56 1422mm (4’ 8”)

AX20-5B/42 1066mm (3’ 6”)
More than 2.5m (8’ 2”)

11 12