License=Al Sharif Group & KEC Co.

Ltd/SA-881-t Not For Resale ,1/23/2023 8:19:12 PM Saudi Time

 INSPECTION AND TEST PLAN (ITP) FOR LINE HARDWARE

Type Sample

Contract No. / Project Title:

Manufacturer Name: ITP No. : ITP-LHW-02
Plant Location:
Review Cycle No :
Material / Equipment Description: Line Hardware
Date:
Type of Material / Equipment
No. of days:

Equipment Technical data (To be filled by the manufacturer):

Rated Voltage (Ur [kVrms]) 110/115/132/230/380
Highest Voltage (Um [kV]) To be filled by the manufacturer
Rated Current (A) To be filled by the manufacturer
Rated Frequency (Hz) 60
SEC/National Grid SA Specification No. 12-TMSS-01, Rev.02

Applicable Sample Insp. Test Manufacturer

Item Test Description Test Procedures Type
Acceptance Criteria Location
Remarks
Unit Standards Compliance
Hot Dip Galvanizing

- Hardware Fittings µm 12-TMSS-01 Clause 9 of IEC 5 110

1 W
- Fasteners Clause 7.1.1.a 61284 53(fastener˃9.52mm)
43(fasteners≤9.52mm)
- Washers 53 (washers)
Mechanical Failing Load
12-TMSS-01 Clause 11 of IEC
2 Test (on individual kN 5 W No failure
Clause 7.1.1.b 61284
hardware fittings)
100 (for 100 to 132kV)
kV 12-TMSS-01 Clause 14 of IEC 185 (for 230kV)
3 Corona and (RIV) Test String W 300 (for 380kV)
Clause 7.1.1.c 61284
dB 40
Optionally
Residual strength after power Manufacturer
Power Arc Test/Short 12-TMSS-01
4 kN IEC 61467 String W arc test shall not be less than may propose
Circuit Test (X-Series) Clause 7.1.1.d
70% of rated value Circuit C of
Y-series

ITP-LHW-02 Standards & Specifications Department PAGE 1 OF 2

License=Al Sharif Group & KEC Co. Ltd/SA-881-t Not For Resale ,1/23/2023 8:19:12 PM Saudi Time
 INSPECTION AND TEST PLAN (ITP) FOR LINE HARDWARE

Applicable Sample Insp. Test Manufacturer

Item Test Description Test Procedures Type
Acceptance Criteria Location
Remarks
Unit Standards Compliance

Slip Load Test on 12-TMSS-01 Clause 11 of IEC

5 kN 5 W No slippage
AGS/Suspension Clamps Clause 7.1.1.e 61284
Clamp Bolt Tightening
12-TMSS-01 Clause 11 of IEC
6 Test (on AGS/ 5 W No failure
Nm Clause 7.1.1.f 61284
Suspension Clamps)
Magnetic losses of the clamp
Magnetic Loss test on Clause 12 of IEC shall be less than or equal to
7 5 W
AGS/Suspension Clamp Watts 61284 α times the power losses per
IEC 61284 unit length of the conductor.

Legend:

W = Witness [by SEC/National Grid SA Engineers. and/or SEC approved 3rd Party Independent Inspection Agency (IIA) Inspector]
RC = Review of Certificates [by SEC/National Grid SA Engineers. and/or approved 3rd Party Independent Inspection Agency (IIA) Inspector]

General instructions:
1- Manufacturer’s compliance shall be indicated in front of each test.
2- Approved Data Schedule & final drawings for the equipment / Material shall be attached.
3- Test Procedure & Day-to-day activity schedule shall be attached for approval.
4- The ITP must be duly signed and stamped by manufacturer's authorized personnel.
5- This document is valid for testing after S&SD approval.

Prepared by (Mfr's authorized QC test inspector) Approved by: (Mfr's authorized QA/QC personnel)

Date:
Date:
Manufacturer Stamp

S&SD Approval

ITP-LHW-02 Standards & Specifications Department PAGE 2 OF 2

License=Al Sharif Group & KEC Co. Ltd/SA-881-t Not For Resale ,1/23/2023 8:19:12 PM Saudi Time