0% found this document useful (0 votes)

331 views45 pages

2020 06 01 Drawings For Tender PDF

Uploaded by

tmus bach

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

331 views45 pages

2020 06 01 Drawings For Tender PDF

Uploaded by

tmus bach

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 45

180 Eugenie Street West

Windsor, ON N8X 2X6

519.258.1390

This drawing is not to be used for construction

unless it is countersigned by the Project Architect

Issued For (YYYY.MM.DD)

TENDER 2020.06.01

ERCA
John R. Park Homestead Heritage Centre
915 County Road 50, Essex, Ontario N0R 1G0

Date
Project No. 2020

Revision Schedule

Description
ARCHITECTURAL SHEETS STRUCTURAL SHEETS MECHANICAL SHEETS ELECTRICAL SHEETS
No. SHEET NAME No. SHEET NAME No. SHEET NAME No. SHEET NAME
A000 COVER SHEET S001 GENERAL NOTES M001 MECHANICAL LEGEND E001 GENERAL ELECTRICAL NOTES -1
A001 GENERAL INFORMATION S101 FOUNDATION PLAN & SAWCUT LAYOUT M002 MECHANICAL GENERAL NOTES E002 GENERAL ELECTRICAL NOTES -2
A002 CODE COMPLIANCE S102 FOUNDATION SECTIONS M201 SANITARY & STORM E101 SITE PLAN - PHOTOMETRIC

No.
A101 OVERALL SITE PLAN S201 ROOF & MEZZANINE FRAMING PLANS M202 DOMESTIC WATER E102 SITE PLAN - POWER & LIGHTING
A102 ENLARGED SITE PLAN S601 FRAMING SECTIONS M303 AIR DISTRIBUTION E201 LIGHTING FLOOR PLAN
A201 FLOOR PLANS S701 FRAMING ELEVATIONS M304 AIR DISTRUBUTION E202 LIGHT FIXTURES & LIGHT CONTROL SCHEDULES
A202 WALL & FLOOR FINISH PLANS S702 FRAMING ELEVATIONS M305 SECTIONS E203 LIGHTING CONTROL SCHEMATICS
A203 INTERIOR ELEVATIONS M400 EQUIPMENT SCHEDULE E301 POWER & SYSTEMS FLOOR PLAN
A204 INTERIOR ELEVATIONS M401 TYPICAL DETAILS E302 ELECTRICAL PANEL SCHEDULE & DETAILS
A205 ROOF PLAN
A301 FIRST FLOOR REFLECTED CEILING PLAN
A401 EXTERIOR ELEVATIONS
A501 BUILDING SECTIONS
A502 BUILDING SECTIONS
A503 BUILDING SECTIONS
A601 WALL SECTIONS
A602 WALL SECTIONS
A603 WALL SECTION DETAILS
A701 WASHROOM PLANS & ELEVATIONS
A901 STAIR PLAN, SECTION, AND DETAILS

COVER SHEET
A1201 MILLWORK

Sheet Name

915 County Road 50, Essex, Ontario N0R 1G0

John R. Park Homestead Heritage Centre
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

ERCA
Drawn By Checked By
Ai Ai
6/1/2020 9:52:01 AM

Project No
2020
Sheet No

ACC AIR CONDITIONING CONDENSING UNIT N.I.C. NOT IN CONTRACT Floor Finish as per 1/A202 ACOUSTICAL CEILING (ACT-1)
ROOM NAME F1 ACT-1 19mm COMPOSITE WOOD SIDING (REFER TO ELEVATIONS FOR TYPE)
ACP ALUMINUM COMPOSITE PANELS ND SANITARY NAPKIN DISPOSAL ROOM NUMBER 4" Concrete Slab on Grade (refer to Structural) 24"X24" Acoustical Ceiling Tile
ACT ACOUSTIC CEILING TILE NV SANITARY NAPKIN VENDOR 101a 10mil Poly Vapour Barrier w/ suspension system 19mm x 90mm VERTICAL WOOD STRAPPING SPACED AT 600mm O.C.
ADO AUTOMATIC DOOR OPERATOR OH OVERHEAD Compacted Gravel (Refer to Specifications and Reflected Ceiling Plans) AIR BARRIER
101 DOOR NUMBER 50mm RIGID INSULATION (MIN. R-10)
AL ALUMINUM OPP OPPOSITE
AN ANODIZED P.LAM PLASTIC LAMINATE 50mm GALVANIZED STEEL Z-GIRTS SPACED AT 1200mm O.C.
W1
1t WINDOW TYPE 13mm EXTERIOR GRADE PLYWOOD SHEATHING
AFF ABOVE FINISH FLOOR PT PAINT
ARS ASSISTANCE REQUIRED SIGNAL PTD PAPER TOWEL DISPENSER/DISPOSAL 38mm x 140mm WOOD STUDS SPACED AT 400mm O.C.
AVS AUDIBLE VISUAL SIGNAL PTL PUSH TO LOCK W1a WALL TYPE/ CEILING TYPE TECTUM CEILING PANEL w/ 140mm STONE WOOL BATT INSULATION (MIN. R-22) 180 Eugenie Street West
AWP ACOUSTIC WALL PANEL RA ROOF ANCHOR Floor Finish as per 2/A202 24"X48" Acoustical Ceiling Panels 6 mil. POLY VAPOR BARRIER Windsor, ON N8X 2X6
F2 TECTUM 519.258.1390
BL BREAK LINE RB RESILIENT BASE F-1 FLOOR TYPE 3/4" Plywood sheathing fastened to u/s insulated roof panels VARIES 13mm GYPSUM BOARD U.N.O. (REFER TO FINISHES PLAN)
CBLK CONCRETE BLOCK RD ROOF DRAIN 9.5" Pre-Engineered Wood I-Joists (refer to Structural) (Refer to Specifications and Reflected Ceiling Plans)
CG CORNER GUARD RFID RADIO FREQUENCY IDENTIFICATION Ceiling Finish as per 3/A303
R-1 ROOF TYPE
CH COAT HOOK RWL RAIN WATER LEADER
CJ CONTROL JOINT SCW SOLID CORE WOOD 13mm GYPSUM BOARD
CL CLEAR GLASS SD SOAP DISPENSER ? MATERIAL TYPE GYPSUM BOARD CEILING (C-1) P2b 38mm x 89mm WOOD STUDS SPACED AT 400mm O.C.
CONC CONCRETE SHWR SHOWER C-1
1/2" Gypsum board 13mm GYPSUM BOARD U.N.O. (REFER TO FINISHES PLAN)
CPT CARPET TILE SIM SIMILAR w/ suspension system
1 REVISION NUMBER
CR CARD READER SLR CONCRETE SEALER (Refer to Specifications and Reflected Ceiling Plans)
CT PORCELAIN TILE SR SERVER RACK This drawing is not to be used for
CUH CABINET UNIT HEATER S.S STAINLESS STEEL No ROOF TYPE LEGEND 13mm GYPSUM BOARD
construction unless it is countersigned
by the Project Architect
CV CONVECTOR SSS STAINLESS STEEL SHELF
CW CURTAIN WALL SVT SOLID VINYL TILE P2c 38mm x 140mm WOOD STUDS SPACED AT 400mm O.C.
EXTERIOR BUILDING TYPE SECTION DESCRIPTION GYPSUM BOARD BULKHEAD (B-1) 13mm GYPSUM BOARD U.N.O. (REFER TO FINISHES PLAN) Issued For (YYMMDD)
DS DOWNSPOUT TB TACK BOARD No SHEET No B-1
EBP EMERGENCY PUSH BUTTON TG TINTED GLASS ELEVATION INDICATOR 1/2" Gypsum board on metal framing TENDER 2020.06.01
EP ELECTRICAL PANEL TM TILTED MIRROR Asphalt Shingles (see specs) (Refer to Details and Reflected Ceiling Plans)
ES EMERGENCY SIGN T.O. TOP OF No R1 Moisture Barrier
EX EXISTING TP TOILET PAPER HOLDER 257mm Structurally Insulated Panel
FB FLOOR BOX - ELECTRICAL TPG TEMPERED GLASS - Consisting of 2 layers 11mm osb board c/w 235mm insul. 38mm x 89mm WOOD STUDS SPACED AT 400mm O.C.
F2b
FD FLOOR DRAIN TWSI TACTILE WALKING SURFACE INDICATOR MILLWORK SOUND ATTENUATION BLANKET BETWEEN WASHROOM,VEST,CORRIDOR & SERVERY
No SHEET
FE FIRE EXTINGUISHER U.N.O. UNLESS NOTED OTHERWISE ELEVATION INDICATOR *Install SIP & roofing system as per SIP manufacturer's recommended 13mm GYPSUM BOARD U.N.O. (REFER TO FINISHES PLAN)
FHC FIRE HOSE CABINET U/S UNDERSIDE installation instructions.
FM FLAT MIRROR V.I.F. VERIFY IN FIELD **Refer to Reflected Ceiling Plans for interior finishes
GB GRAB BAR VFL VINYL FLOOR
GL GLASS VCT VINYL COMPOSITE TILE SECTION INDICATOR TYP. CANOPY ROOF CONSTRUCTION
No R2 38mm x 140mm WOOD STUDS SPACED AT 400mm O.C.
GYP BD GYPSUM BOARD WB WHITE BOARD Single Ply Roof Membrane on F2c
SHEET 13mm GYPSUM BOARD U.N.O. (REFER TO FINISHES PLAN)
HM HOLLOW METAL WD WOOD 13mm Fiberboard on
IG INSULATED GLASS WI WIRED GLASS 25mm Polyisocyanate Insulation on
IM INSULATED METAL WP WATERPROOFING Vapour Retarder on
INS INSULATION 19mm Exterior Grade T&G Plywood Sheathing on
1 HOUR F.R.R.
38mm x 184mm Roof Joist @ 300mm o.c. w/
Vented Prefinished Soffit (TYP) U2b 13mm TYPE 'X' GYPSUM BOARD (25 MIN; SB-2 Table 2.3.4.A.)
38mm x 89mm WOOD STUDS SPACED AT 400mm O.C. (20 MIN; SB-2 Table 2.3.4.E.
13mm TYPE 'X' GYPSUM BOARD (25 MIN; SB-2 Table 2.3.4.A.)

Date
1 HOUR F.R.R.

U2c 13mm TYPE 'X' GYPSUM BOARD (25 MIN; SB-2 Table 2.3.4.A.)
38mm x 140mm WOOD STUDS SPACED AT 400mm O.C. (20 MIN; SB-2 Table 2.3.4.E.
13mm TYPE 'X' GYPSUM BOARD (25 MIN; SB-2 Table 2.3.4.A.

Revision Schedule

Description
*EXTERIOR ELEVATION
*INTERIOR ELEVATION
2770

No.
50 263 50 2013 50 374 50 295 50 2013 50 262 50

50
50
WINDOW SYSTEMS - GENERAL NOTES
DOOR SCHEDULE

50 325

425

325

425
GL1 GL1 GL1 GL2 GL2 GL2 1. WINDOW SYSTEMS & ANCHORAGE ARE TO BE DESIGNED TO
PANEL FRAME EXIT COMPLY WITH ALL APPLICABLE BUILDING CODES. DRAWINGS

1039 50
ALUM. (TYP.)
NO. TYPE QTY. WIDTH HEIGHT MAT. FINISH TYPE MAT. FINISH GLAZING CLOSER DEVICE F.R.R. HARDWARE REMARKS ALUM. (TYP.) SHALL BE REVIEWED AND BEAR THE SIGNED SEAL OF A
PROFESSIONAL ENGINEER LICENSED TO PRACTICE IN THE

1039
PROVINCE OF ONTARIO PRIOR TO SUBMITTAL TO ARCHITECT'S
101a P-3 2 2013 2134 AL AN * AL AN CL, TP, IN 2 2 - REFER TO WINDOW ELEVATIONS FOR FRAME TYPE ALUM. TRIM w/
OFFICE. REFER TO SPECIFICATIONS

2559

2559
INSUL. BOARD
101b P-3 2 2013 2134 AL AN * AL AN CL, TP, IN 2 2 - REFER TO WINDOW ELEVATIONS FOR FRAME TYPE GL1 GL1 GL1 GL1 GL2 GL2
GL2 GL2

2134

2134
OVER COLUMN

GENERAL INFORMATION
102 P-2 1 1000 2150 HM PAINT F-1 HM PAINT N/A 1 1 - - 2. REFER TO SHEET A001 FOR INTERIOR HOLLOW METAL FRAME

50
50
103 P-1 1 1000 2150 HM PT F-1 HM PT N/A - - - - WINDOW SYSTEM ELEVATIONS

1070

1070
995

50 995
104 P-2 1 1000 2150 HM PT F-1 HM PT CL, TP - - - - GL1 GL1
GL2 GL2
105 P-1 1 1000 2150 HM PT F-1 HM PT N/A - - - -

50
GL1 GL1 GL2 GL2
106a P-1 1 1050 2100 HM PT F-1 HM PT N/A - - 45 MIN - FIRST FLOOR EXTERIOR INSULATED GLAZING
106b P-1 1 1000 2150 HM PT F-1 HM PT N/A - - - PROVIDE 25MM DOOR UNDERCUT 0 - REFER TO SPECIFICATIONS
GL-1
108a P-2 2 1016 2134 HM PT F-3 HM PT CL,TP 1 1 45 MIN -
108b P-3 2 2030 2134 AL AN * AL AN CL, TP, IN 2 2 - REFER TO WINDOW ELEVATIONS FOR FRAME TYPE CW1 STOREFRONT ELEVATION CW2 STOREFRONT ELEVATION
109a P-2 1 1000 2150 HM PT F-1 HM PT CL, TP 1 - 1 HR - INTERIOR SINGLE PANE GLAZING
SCALE: 1 : 50 SCALE: 1 : 50 - REFER TO SPECIFICATIONS
109b P-5 1 2000 1000 ST NAT - ST NAT - - - - ROLLING SHUTTER DOOR GL-2
112a P-3 1 965 2134 HM PT F-1 HM PT CL, TP - - - -
112b P-1 1 1000 2150 HM PT F-1 HM PT N/A - - - - *EXTERIOR ELEVATION 2134
116 P-1 1 1000 2150 HM PT F-1 HM PT N/A - - - - 50 1230 50 1249

50325 50
GL2

ALUM. (TYP.)

1414
ALUM. (TYP.)
ALUM. TRIM w/
INSUL. BOARD

2559

2559
OVER COLUMN
GL1 GL1 GL2 GL2

2134
50

John R. Park Homestead Heritage Centre

1070
995

915 County Road 50, Essex, Ontario N0R 1G0

GL2 GL2
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

GL1 GL1
FIRST FLOOR
2875
0

50
51 EQ. 51 EQ. 51
CW3 STOREFRONT ELEVATION CW4 STOREFRONT ELEVATION
51

SEE DOOR SCHEDULE SEE DOOR SCHEDULE SEE DOOR SCHEDULE SEE DOOR SCHEDULE
MATERIAL LEGEND: OH OVERHEAD SCALE: 1 : 50 SCALE: 1 : 50
140 VARIES 140 AL ALUMINUM PT PAINT
51 415
51

140

AN ANODIZED SCW SOLID CORE WOOD

CL CLEAR GLASS ST STAIN 950
1490
51 51 SEE DOOR SCHEDULE 140 140 CR CARD READER TP TEMPERED GLASS
1110 1110
VARIES

50 50
VERIFY ONSITE

SEE DOOR SCHEDULE

50 50
VARIES

VARIES
SEE DOOR SCHEDULE

DO DOOR OPERATOR TG TINTED GLASS

IM INSULATED METAL WI WIRED GLASS
SEE DOOR SCHEDULE
2650

IG INSULATED GLASS WD WOOD

50
203

VARIES 200
203

PT. STL
DOOR NOTES:

1360

1360
PT. STL
1. ALL GLAZING IN DOORS & SIDELIGHTS SHALL BE TEMPERED.
1118

VARIES

1203

1203
2. PROVIDE WEATHERSTRIPPING FOR ALL EXTERIOR DOORS.
3. REFER TO MECHANICAL DRAWINGS FOR ALL DOOR LOUVRE GL2

50
50
GL2
SIZES AND TYPES - LOUVRE SHALL BE PRE-FINISHED w/ COLOUR TO
MATCH DOOR AND / OR FRAME.
300

4. ALL DOOR HARDWARE TO BE REVIEWED BY ARCHITECT FOR APPROVAL.

910

910
5. DOOR FRAME INFORMATION INDICATED WITH * ON THE DOOR
*SEE EXTERIOR ELEVATIONS & *SEE EXTERIOR ELEVATIONS &

ERCA
F-1 F-2 P-1 P-2 P-3 SCHEDULE REQUIRES COORDINATION WITH THE SCREEN TYPE LEGEND.
6. REFER TO SCHEDULE FOR DIMENSIONS INDICATED AS "VARIES" TYP. WINDOW DETAILS FOR TYP. WINDOW DETAILS FOR FIRST FLOOR
SILL HEIGHTS SILL HEIGHTS 0
FRAME TYPES PANEL TYPES

W1 - WINDOW ELEVATION W2 - WINDOW ELEVATION W3 - WINDOW ELEVATION W4 - WINDOW ELEVATION Drawn By Checked By

SCALE: 1 : 50 SCALE: 1 : 50 SCALE: 1 : 50 SCALE: 1 : 50 Ai Ai

6/1/2020 8:37:06 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

Firm Name: Architecttura Inc. Architects Name of Project: EXAMPLE: OCCUPANCY CALCULATION
Certificate of Practice Number: 3267
??? OFFICE ROOM DESCRIPTION
180 Eugenie St. W. 9.3 OCCUPANT LOAD (m2 / PERSON) OBC 3.1.17.1
Windsor, ON N8X 2X6 Location: The architect noted above has exercised responsible 15 AREA OF ROOM (m2)
The Certificate of Practice Number control with respect to design activities. The architect's *1 OCCUPANTS (* INDICATES BY AREA DESIGN 3.1.17.1.(1,c,i))
of the holder is the holder's BCDN. ??? seal number is the architect's BCDN.

Item Ontario Building Code Data Matrix Parts 3 & 9 OBC Reference EXAMPLE: EXIT CALCULATION
180 Eugenie Street West
STAIR EXIT DESIGNATION Windsor, ON N8X 2X6
1 Project Description New Part 11 x Part 3 Part 9 519.258.1390
914 PROVIDED DOOR WIDTH (mm)
Addition 11.1 to 11.4 2.1.1 2.1.1 790 REQUIRED DOOR WIDTH (mm) OBC 3.4.3.2.
Alteration 9.10.1.3 1270 PROVIDED STAIR WIDTH (mm) CARRY RATED GYPSUM FIRE DAMPER BY DIV. 23
900 REQUIRED STAIR WIDTH (mm) OBC 3.4.3.2. AROUND FLOOR STRUCTURE (SEE SPECS)
2 Major Occupancy(s) Group A, Division 2 3.1.2.1.(1) 9.10.2 149 PROVIDED OCCUPANCY EXIT CAPACITY (PERSONS) & UP TO MEET DAMPER CARRY RATED GYPSUM AROUND
WOOD STUDS PRIOR TO
3 Building Area Existing: N/A New: 365m² Total: 365m² 1.1.3.2 1.1.3.2 INSTALLATION OF FIRE DAMPER
4 Gross Area Existing: N/A New: 455m² Total: 455m² 1.1.3.2 1.1.3.2 3/4 NEW FIRE SEPARATIONS - NUMBER INDICATES
FIRE-RESISTANCE RATING IN HOURS
5 Number of Storeys Above Grade: 1 Below Grade: N/A 3.2.1.1 & 1.1.3.2 2.1.1.3
6 Number of Streets/Firefighter Access: 1, Refer to Site Plan 3.2.2.10 & 3.2.5. 9.10.19 This drawing is not to be used for
X-3/4 EXISTING FIRE SEPARATIONS - NUMBER INDICATES construction unless it is countersigned
7 Building Classification: 3.2.2.28. Group A, Division 2, 1 Storey 3.2.2.20-.83 9.10.4 FIRE-RESISTANCE RATING IN HOURS NOTE: INSTALL FIRE DAMPERS FOLLOWING WOOD FLOOR by the Project Architect
ALL MANUFACTURER'S RECOMMENDED STRUCTURE
8 Sprinkler System Proposed 3.2.2.20-.83 9.10.8 INSTALLATION INSTRUCTIONS & FOLLOW FIRE DAMPER & DUCT BY DIV. 23
Issued For (YYMMDD)
entire building 3.2.1.5 (SEE SPECS)
ALL LOCAL REGULATORY REQUIREMENTS. TENDER 2020.06.01
basement only 3.2.2.17
in lieu of roof rating
not required
NOTE: INSTALL FIRE DAMPERS FOLLOWING
9 Standpipe required Yes No 3.2.9 N/A ALL MANUFACTURER'S RECOMMENDED
10 Fire Alarm required Yes No 3.2.4 9.10.17.2 INSTALLATION INSTRUCTIONS & FOLLOW
ALL LOCAL REGULATORY REQUIREMENTS.
11 Water Service/Supply is Adequate Yes No 3.2.5.7 N/A
12 High Building Yes No 3.2.6 N/A
13 Permitted Construction Combustible Non-combustible Both 3.2.2.20-.83 9.10.6
Actual Construction Combustible Non-combustible Both 3 TYPICAL FIRE DAMPER FLOOR PENETRATION 4 TYPICAL FIRE DAMPER WALL PENETRATION
14 Mezzanine(s) Area = 90.25m² 3.2.1.1.(3)-(8) 9.10.4.1
SCALE: 1 : 5 SCALE: 1 : 5
15 Occupant load based on: Design 3.1.16 9.9.1.3

Occupancy Group A, Division 2 Load 90 persons

16 Barrier-free Design Yes No (Explain) 3.8 9.5.2

Date
17 Hazardous Substances Yes No 3.3.1.2 & 3.3.1.19 9.10.1.3(4)
18 3.2.2.20-.83 & 3.2.1.4 9.10.8
Horizontal Assemblies Listed Design No.
Required Fire 9.10.9
FRR (Hours) or Description (SG-2)
Resistance
Rating (FRR) Floors N/A N/A
Roof No FRR Required N/A; Combustible Provided

Revision Schedule
Mezzanine No FRR Required N/A; Combustible Provided EXIT
2000
FRR of Supporting Listed Design No. 790
Members or Description (SG-2)

Description
N/A
Floors N/A N/A N/A
328
Roof No FRR Required N/A; Combustible Provided DASHED LINE INDICATES PROJECTION OF EXTERIOR
BUILDING FACE AS A VERTICAL PLANE TO DETERMINE
Mezzanine No FRR Required N/A; Combustible Provided LIMITING DISTANCE (L.D.) - REFER TO SITE PLAN FOR
19 Spatial Separation - Construction of exterior Walls (Table 3.2.3.1.B.) 3.2.3 9.10.14 CORRESPONDING DIMENSIONS. OBC 3.2.3.1.(3)

Wall Area of EBF L.D. Permitted Max. Proposed % of FRR Listed Design or TYPE OF TYPE OF
(m²) (m) L/H % of Openings Openings (Hours) Description CONSTRUCTION CLADDING
REQUIRED REQUIRED WEST (a) L.D. 22.21m TO
EXISTING CALF BARN
North 93.34m² 98.98m N/A; Limiting Distance Over 13m Both Perimitted; Both Perimitted; REFER TO SITE PLAN

No.
Combustible Provided Combustible Provided
CLASSROOM
South 93.34m² 59.72m N/A; Limiting Distance Over 13m Both Perimitted; Both Perimitted; 1.85m²
Combustible Provided Combustible Provided 49.55 m²
26
East 101.15m² 20.54m N/A; Limiting Distance Over 16m Both Perimitted; Both Perimitted; OPEN TO BELOW
Combustible Provided Combustible Provided
West (a) 20.43m² 22.39m N/A; Limiting Distance Over 8m Both Perimitted; Both Perimitted;
Combustible Provided Combustible Provided

West (b) 50.89m² 76.19m N/A; Limiting Distance Over 10m Both Perimitted; Both Perimitted; TRAVEL DISTANCE CONTINUED ON
Combustible Provided Combustible Provided FIRST FLOOR - REFER TO CODE
COMPLIANCE PLAN - FIRST FLOOR
West (c) 24.12m² 4.25m 3.2 : 1 51.25% 13.2% 45 Min. Refer to Wall Type Both Perimitted; Both Perimitted; EXIT
Legend & Floor Plan Combustible Provided Combustible Provided 1000

CODE COMPLIANCE
790
20 Fire Resistance Ratings Construction Type Used Required Rating OBC Reference TRAVEL DISTANCE: 25.31m N/A
N/A
Exits N/A N/A 3.4.4.1. 164
WEST (b) L.D. 76.01m TO
PROPERTY LINE REFER OFFICE
Floors N/A N/A 3.2.2.28.
TO SITE PLAN N/A
17.54 m²

TRAVEL DISTANCE: 25.60m

Service rooms w/o fuel fired appliances N/A N/A 3.6.2.1. (8) *3
OPEN TO BELOW
MECH. ROOM MEZZ.
Service rooms w/ fuel fired appliances U2c; Refer to Wall Type Legend 1 Hour 3.6.2.1. (7) (OPEN)
TRAVEL DISTANCE: 22.21m

Electrical rooms U2c; Refer to Wall Type Legend 1 Hour 3.6.2.1.(6).

SERVERY .
CLOSET 1 HOUR FIRE SEPARATION AS HATCHED AREA INDICATES 1 HOUR
Janitors Room U2b; Refer to Wall Type Legend 1 Hour 3.3.1.20. N/A
PER OBC 3.6.2.1.(6) FIRE SEPARATION AT UNDERSIDE
13.63 m²
ELECT. 1 HOUR FIRE SEPARATION AS OF MEZZANINE.
*2

John R. Park Homestead Heritage Centre

21 Plumbing Fixtures: Total occupant load for building: 90 ROOM PER OBC 3.3.1.20.
OCCUPANTS LOAD FIXTURE TYPE REQUIRED PROVIDED

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

WATER CLOSETS (Table 3.7.4.3.A.) 1 4 + 1 Universal Washroom; 5 Total

MALE 45

TRAVEL DISTANCE: 14.42m

LAVATORIES 1 3 + 1 Universal Washroom; 4 Total

FEMALE 45 WATER CLOSETS (Table 3.7.4.3.A.) 2 4 + 1 Universal Washroom; 5 Total CLASSROOM

LAVATORIES 1 3 + 1 Universal Washroom; 4 Total 1.85m²
110.48 m²
59

WEST (c) L.D. 4.25m TO EXIT

EXISTING GIFT SHOP 2000 OPEN TO BELOW
REFER TO SITE PLAN 790
N/A
N/A
328

1 HOUR FIRE RESISTANCE RATING TRAVEL DISTANCE: 16.22m

ERCA
AS PER OBC Table 3.2.3.7.

N N Drawn By Checked By
Author Checker
6/1/2020 8:37:10 AM

CODE COMPLIANCE PLAN - FIRST FLOOR CODE COMPLIANCE PLAN - MEZZANINE

Project No
SCALE: 1 : 100 SCALE: 1 : 100
2020
THIS LINE IS 4" LONG
Sheet No

1. ZONING CLASSIFICATION A1.2 A1.2 13.2

2. PERMITTED USE COMMUNITY CENTRE COMMUNITY CENTRE S28.1.16

3. MINIMUM LOT AREA AS EXISTING EXISTING 13.2.II 130.15

m
4. MINIMUM LOT WIDTH 30m >30m 13.2.I

24.58 m

14.73 m
5. SETBACK - FRONT YARD 15m MINIMUM 71m 13.2.V 180 Eugenie Street West
ADDITIO Windsor, ON N8X 2X6
NALLOT FO 519.258.1390
6. SETBACK - SIDE YARD 3m MINIMUM - INTERIOR 74m INTERIOR 13.2.VII R
15m MINUMIM - EXTERIOR 155.6m EXTERIOR 1801 SM PARKING

7. SETBACK - REAR YARD 15m MINIMUM 73.86m 13.2.VI

8. LOT COVERAGE 25% OF LOT AREA 2.59% 13.2.III ALL BLDGS COMBINED

9. LANDSCAPED AREA N/A N/A N/A N/A

10. BUILDING HEIGHT 10m MAXIMUM 8.6m 13.2.IV This drawing is not to be used for
construction unless it is countersigned
by the Project Architect
11. PARKING SPACE - SIZE 5.5m MINIMUM L 62.9m L 11.2 SITE VERIFY
2.75m MINIMUM W 26.4m W
Issued For (YYMMDD)
TENDER 2020.06.01
12. PARKING SPACES 25 SPACES 49 SPACES 11.5
0
PRPOSED HERITAGE CENTRE 1/90m2 GFA - 04 SPACES
.5
HOUSE 1/90m2 GFA - 03 SPACES RD
LOOM SHED 1/90m2 GFA - 01 SPACE
NTY
SMOKE HOUSE 1/90m2 GFA - 01 SPACE U
ICEHOUSE 1/90m2 GFA - 01 SPACE CO
OUTHOUSE 1/90m2 GFA - 01 SPACE
SEX
BLACKSMITH 1/90m2 GFA - 01 SPACE ES
CLASSROOM 1/36m2 GFA - 04 SPACES
HORSE BARN 1/90m2 GFA - 02 SPACES
GIFT SHOP 1/22.5m2 GFA - 05 SPACES
CALF BARN 1/90m2 GFA - 01 SPACE
SAWMILL 1/90m2 GFA - 02 SPACES
LEGEND

LANDSCAPING EXISTING NOTES:

ASPHALT 1. REFER TO CIVIL DRAWINGS FOR ALL PAVEMENT
(SEE LANDSCAPE BUILDING
SURFACE MATERIAL PROFILES AND BASE MATERIALS
DRAWINGS) COVERAGE

Date
2. REFER TO LANDSCAPE PLAN FOR LANDSCAPE
EXISTING NEW INFORMATION.

ILE
CONCRETE
LANDSCAPE BUILDING
SURFACE
3. REFER TO CIVIL DRAWINGS FOR ALL PROPOSED

RR
TO BE REMOVED COVERAGE
GRADES. EXISTING

D.
REFUSE
4. ALL CONCRETE APRONS AT AREA
B.F. - "BARRIER FREE PARKING" SIGN EXTERIOR DOOR OPENINGS TO MEET FLUSH

Revision Schedule
F.R. - "FIRE-ROUTE - NO PARKING" SIGN (BARRIER FREE).
B.D.O. - "BUS DROP OFF ZONE" SIGN
S.S. - "STOP" SIGN 5. PROVIDE BARRIER FREE
0

Description
REFER TO PLAN FOR LOCATION OF ALL SIGNAGE
CURB DROPS WHERE SIDEWALKS MEET ASPHALT
D.5
PAVEMENT. R
(REVIEW w/ ARCHITECT PRIOR TO FINAL PLACEMENT)
TY

2.1
0m
U N
CO

99.03 m (NORTH L.D.)

FIRE R
X OVERALL AREA
SE E

11.05 m
S LIN
Y 54150 SM

OUTE
E RT
O PE
PR
9.2
7m

30m BU

81
FFER

.57
OF

No.
CH

m
5.00 m ES
TN
UT

TR
EXISTING PARKING DENOTED 8.26 m 5.50 m 52.46 m

13.50 m

EE
TO ESTABLISH NUMBER OF

S
49 PARKING SPACES
1845 SM
(EAST L.D.)
16.93 m 20.61 m

(OVERALL BUILDING)

FL
O
OD

OVERALL SITE PLAN

L IN
22.39m [WEST (a) L.D.]
EXISTING CALF BARN

E
AREA - 119.3 SM

PRINCIPLE
ENTRANCE

26.21 m (OVERALL BUILDING)

EXISTING SAWMILL
76.19 [WEST (b) L.D.] NEW ONE-STOREY AREA - 144.8 SM
HERITAGE CENTRE
BUILDING AT GRADE
AREA - 365 m²
4.25m
[WEST (c) L.D.]

EXISTING GIFTSHOP FFE 176.8M

AREA - 110.5 SM

EXISTING
EXISTING HORSE
BARN ORCHARD
AREA 162.7 SM
GEOTHERMAL
CONSTRUCTION
ZONE PERIMETER

John R. Park Homestead Heritage Centre

GARDEN
EXISTING

915 Essex County Rd 50, Essex, ON N0R 1G0

CLASSROOM
59.76 m (SOUTH L.D.)

AREA - 121.5 SM
BIM 360://2020 JRPH Heritage Centre/2020 SITE-360.rvt

EXISTING
EXISTING OUTHOUSE
CLOSED WELL
AREA - 5.0 SM
EXISTING ICEHOUSE
ESSEX
AREA - 13.0 SM

EXISTING BLACKSMITH
AREA - 44.7 SM

EXISTING LOOM SHED

LINE
AREA - 29.5 SM
F L OO D
EXISTING HOUSE EXISTING SMOKEHOUSE
AREA - 231.8 SM AREA - 9.7 SM
PROPERTY LINE

EXISTING CURATORIAL
AREA - 76.5 SM
(NOT ACCESSIBLE TO PUBLIC) LEAMINGTON

KINGSVILLE

ERCA
LAKE ERIE

ILER RD.
0
D. 5
XR
SE
ES

JOHN R. PARK HOMESTEAD Drawn By Checked By

N CONSERVATION AREA
ai ai
6/1/2020 8:43:50 AM

SITE LOCATION Project No

ARCHITECTURAL SITE PLAN OVERALL
SCALE: 1 : 600 2020
THIS LINE IS 4" LONG
Sheet No

0 6.00 m
D.5

2.0
R

9m
NTY
U
CO
X
SSE

11.05 m
E
INE
180 Eugenie Street West
YL Windsor, ON N8X 2X6
ERT 519.258.1390
OP
PR
EXISTING TELEPHONE

9.2
DISTRIBUTION BOX

7m
EXISTING BORDER TO
GRANULAR PARKING EXISTING 29.61m LONG x .81m WIDE x .30m
DEEP LANDSCAPE AREA TO BE REMOVED

12
30m BUF
NEW 100mm GRANULAR 'A' on 200mm GRANULAR FER O
F CH

0.81 m
'B' FILL ON GEO FABRIC AT REMOVED LANDSCAPE EST
30m NUT
BU TR
BIKE RINGS FF EE This drawing is not to be used for
EXISTING PARKING DENOTED ER S construction unless it is countersigned

9.35 m
TO ESTABLISH NUMBER OF OF by the Project Architect
29.61 m SERVICE AREA CH

6.00 m
49 PARKING SPACES ES
1845 SM TN Issued For (YYMMDD)
UT
TENDER 2020.06.01

13.50 m

TR
EE
S
12

10.94 m
30
m
8.26 m 5.50 m 6.00 m 37.28 m 9.19 m 5.00 m

BU
FF
ER
NEW 100mm GRANULAR 'A' ON 200mm GRANULAR
6.79 m

OF
'B' FILL ON GEO FABRIC AT REMOVED LANDSCAPE
NOTE: PARKING LAYOUT IS FOR

CH
6.00 m

ES
DESIGN PURPOSES ONLY AND

T
NU
NOT IN THE SCOPE OF WORK EXISTING 6.79m WIDE x 17.9m LONG x .30m

TT
DEEP LANDSCAPE AREA TO BE REMOVED

REE
3.40 m 3.40 m 2.40 m

S
2.00 m 2.79 m 2.00 m
5.50 m

1.50 m
CHESTNUT TREES

17.90 m
1.50 m 1.50 m

Date
CONSTRUCTION
PROVIDE SIGNS FOR TYPE A & B ZONE PERIMETER
BARRIER FREE PARKING ROOF LINE
EXISTING CALF BARN 11.64 m
AREA - 119.3 SM

ROUTE
NEW
FIRE
3.03 m

3.03 m
PRINCIPLE

Revision Schedule
EXISTING DITCH
NEW 100mm GRANULAR 'A' ON 200mm GRANULAR ENTRANCE
EXISTING MAIN NEW FROST SLAB
EXISTING SAWMILL
WATER SHUT-OFF 'B' FILL ON GEO FABRIC AT REMOVED LANDSCAPE AREA - 144.8 SM
15.79 m REFER TO A201

Description
VALVE
EXISTING 3.03m WIDE x 15.79m LONG x .30m
DEEP LANDSCAPE AREA TO BE REMOVED 12.88 m NEW ONE-STOREY 20.54 m
EXISTING
HYDRO 23.84 m HERITAGE CENTRE

13.91 m
SERVICE POLE BUILDING AT GRADE
76.16 m
AREA - 365 m²
FFE 176.8M

SPLASH PAD AT DOWNSPOUT

NEW CONC. SLAB LOCATION (TYPICAL) SURFACE
FINISHED

No.
EXISTING GIFTSHOP REFER TO A201 RUNOFF INTO FLOOD PLAIN DISTRIBUTION UNTREATED BUILDING PAPER
GRADE

9.36 m
AREA - 110.5 SM PIPE OR PERMEABLE GEO TEXTILE
NEW FROST SLAB
FABRIC
REFER TO A201 INFILTRATION 2.00 m
REMOVE TREES AS REQUIRED, CONFIRM ONSITE
& REPORT TO ARCHITECT PRIOR TO REMOVAL CHAMBERS
[SPACING BETWEEN TRENCH (TYP)
EXISTING

2.86 m
REFER TO MECHANICAL
FOR CONTINUATION ORCHARD
EXISTING HORSE

0.60 m

[MAX]
BARN 4" PVC DR28 PIPE

9.46 m
AREA 162.7 SM 4.25m
[WEST (c) L.D.] OBC 3.2.3.1B SEPTIC TANK

[VERTICAL SEPARATION MIN 900 MM]

GEOTHERMAL
PERMITTED OPENING <13%

ENLARGED SITE PLAN

TREATMENT UNIT
PROVIDED <13% ECO FLOW OR APPROVED

0.45 m
EQUIVALENT

SEPTIC BED DESIGN, CONSTRUCTION AND INSTALLATION BY OTHERS.

0.90 m
SCHEMATIC SHOWN HERE FOR REPRESENTATION ONLY.

0.45 m
GARDEN GEO TECH REPORT INDICATES AN ESTIMATED T-TIME OF 40 MINS/CM.

17.80 m
GEO TECH REPORT INDICATES LOCAL WATER TABLE LEVEL (PERCHED)
EXISTING TO BE WITHIN 450MM OF GROUND SURFACE. A RAISED LEACHING BED
CLASSROOM (ATLEAST 450 MM) IS REQUIRED. DESIGN TO SUIT. H.G. WATER TABLE H.G. WATER TABLE
AREA - 121.5
SM
2.00 m2.00 m2.00 m 1.5" DISTRIBUTION PIPES

FLOO
EXTENT OF LEACHING BED NATIVE EARTH
FILL MATERIAL
EX GRADE LINE

D
IMPORTED FILL (APPROVED BY GEOTECH FOR T-TIME)

55.1

LINE
2.00 m 6.00 m 2.00 m
WASHED SEPTIC STONE

2m
APPROXIMATE LINE OF
EXCAVATION AFTER REMOVING TOP SOIL
TOP SOIL (AVERAGE 0.3 M TOP SOIL)

John R. Park Homestead Heritage Centre

EXISTING

915 Essex County Rd 50, Essex, ON N0R 1G0

CLOSED EXISTING OUTHOUSE SEPTIC BED CROSS SECTION SCHEMATIC (TYP)
WELL AREA - 5.0 SM
BIM 360://2020 JRPH Heritage Centre/2020 SITE-360.rvt

EXISTING ICEHOUSE
AREA - 13.0 SM

EXISTING BLACKSMITH
AREA - 44.7 SM

EXISTING LOOM SHED

AREA - 29.5 SM

EXISTING HOUSE EXISTING SMOKEHOUSE

AREA - 231.8 SM AREA - 9.7 SM E
IN L
O D
F LO

ERCA
EXISTING
LAKE ERIE
CURATORIAL
AREA - 76.5 SM
PROPERTY LINE

(NOT ACCESSIBLE
TO PUBLIC) Drawn By Checked By
ai ai
6/1/2020 8:43:51 AM

N
Project No
ENLARGED SITE PLAN 2020
SCALE: 1 : 300 THIS LINE IS 4" LONG
Sheet No

200
AIR BARRIER CONT. (TYP) CAULKING ON BOTH SIDES (TYP) FOOT GRILLE W/ EDGE TRIM AND
GIRTS @1220mm O.C. MAX. (TYP) VESTIBULE
1 CW3

163 ±
REFER TO SPEC 101 DRAIN PAN MATCH TO INTERIOR NOTE: PLYWOOD SIZE VARIES PER 180 Eugenie Street West
50mm RIGID INSULATION AIR BARRIER FLOOR FINISH ELEVATION JAMB CONDITION TO FILL VOID (TYP) Windsor, ON N8X 2X6

176
CONT. (TYP) 400 519.258.1390
19mm SOLID PINE WOOD SILL, HEAD & JAMB CONT. (TYP) 2

395
CW1 CW2
EXTENSION TO SUIT DEPTH (MATCH GYPSUM

49
DOOR OPERATOR
1 CLEAR AIR

127
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
SPACE (TYP) ABOVE (TYP)
FOUR SIDES (TYP) BY DIVISION 06 10 00
BF BF
PEEL & STICK 13 PROVIDE PERIMETER SHADOW
BEAD TO FINISH GYPSUM
3 ADO VESTIBULE
101

2013
MEMBRANE AROUND ALL 19mm SOLID PINE WOOD SILL, HEAD & JAMB

2642
7 BOARD TO 13mm FROM WOOD 50mm RIGID 13
OPENINGS CONT. (TYP) A201 12.7mm GYPSUM BOARD EXTENSION TO SUIT DEPTH (MATCH GYPSUM
(TYP) REFER TO SPEC INSULATION (TYP) 262 2000 317
VESTIBULE ON 38mm x 89mm WOOD BOARD FACE) w/ STAIN/VARNISH FINISH ALL
6mil POLY VAPOUR BARRIER (TYP) STUDS @ 400mm O.C. TO PROVIDE PERIMETER SHADOW FOUR SIDES (TYP) BY DIVISION 06 10 00 This drawing is not to be used for
101 WELCOME CENTRE
102
4
FILL VOID w/ R20 BATT U/S OF DECK (TYP) BEAD TO FINISH GYPSUM
construction unless it is countersigned
by the Project Architect
13mm EXT. GRADE PLYWOOD INSULATION (TYP) BOARD TO 13mm FROM WOOD
SHEATHING CONT. (TYP)
PREFINISHED ALUMINUM WINDOW
(TYP) REFER TO SPEC 3

362
SYSTEM (TYP.) w/ PERIMETER ADO ADO ADO Issued For (YYMMDD)
ADO
CAULKING ON BOTH SIDES CONT. SOUND ATTENUATION TENDER 2020.06.01

196
13mm EXT. GRADE PLYWOOD BLANKETS AROUND ALL 7 TYP. WINDOW SURROUND SHADOW BEAD DETAIL 4
5 TYP. WINDOW JAMB DETAIL - GYPSUM SHEATHING CONT. 38mmx140mm WOMEN W/R
WASHROOMS (TYP)
A201 SCALE: 1 : 1
WD. STUDS @ 400mm O.C. (TYP)
A201 SCALE: 1 : 10 FIBREGLASS/WOOD WINDOW 113 PROVIDE SOLID WOOD BLOCKING
SYSTEM w/ PERIMETER FOR ALL PLUMBING FIXTURES
CAULKING ON BOTH SIDES (TYP) ACCESSORIES & PARTITIONS (TYP) B PREFINISHED METAL ON
CONCRETE SILL BELOW
7 Sim REFER TO SPEC
PROVIDE PERIMETER SHADOW A201 6 TYP. WINDOW JAMB DETAIL - ALUM. 6mil POLY VAPOUR H.S.S. COLUMN (TYP) 100
PREFINISHED ALUM. 9 ENLARGED VESTIBULE PLAN
BEAD TO FINISH GYPSUM 19mm SOLID PINE WOOD SILL, HEAD & JAMB BARRIER (TYP) REFER TO STRUC. DWGS.
A201 SCALE: 1 : 10 WINDOW SYSTEM w/ A201 SCALE: 1 : 50
BOARD TO 13mm FROM WOOD EXTENSION TO SUIT DEPTH (MATCH GYPSUM PERIMETER CAULKING
(TYP) REFER TO SPEC BOARD FACE) w/ STAIN/VARNISH FINISH ALL ALUMINUM CLADDED ON BOTH SIDES (TYP)
CREATIVE COMMONS FOUR SIDES (TYP) BY DIVISION 06 10 00 INSULATION BOARD (TYP)

100
108
12 7
A201
Sim PEEL & STICK MEMBRANE AROUND
ALL OPENINGS CONT. (TYP)
CL 1 6mil POLY VAPOUR
BARRIER (TYP) CL
B C E PREFINISHED ALUMINUM
B C E
181

H.S.S. COLUMN (TYP) EXT. GRADE PLYWOOD

SKIN COLOUR TO MATCH
REFER TO STRUC. DWGS. G WINDOW FRAME (TYP) SHEATHING CONT. AS G
13 50mm RIGID INSULATION (TYP) 16781 BY WINDOW SUPPLIER REQUIRED (TYP) 16781

Date
AIR BARRIER CONT. (TYP) VESTIBULE
6mil POLY VAPOUR BARRIER (TYP) 6901 19 1495 1495 6871 AIR BARRIER CONT. (TYP) 101 6901 1514 1495 2809 4062
13mm EXT. GRADE PLYWOOD COMPOSITE HORIZ. WOOD
SHEATHING CONT. (TYP) SIDING ON 38mm x 89mm VERT. 1500 5552 1325 76 1325 7003 5196 10084
WOOD STRAPPING ON BUILT-UP 8 TYP. WINDOW JAMB DETAIL - VEST. 1325 76 1325 7003
CLEAR AIR SPACE (TYP) 331 WOOD COLUMN (TYP) 2550
1 1 3521 ±
A501
2 A201 SCALE: 1 : 10 FROST SLAB CONSTRUCTION:
A601 FROST SLAB
F A501 102mm CONC SLAB w/ 152mm x
1 MS-2 2

Revision Schedule
152mm - M.W. 13.3 x M.W. 13.3 W.W.M. 9 A501
A501 5 2 Sim 1
4 TYP. WINDOW JAMB DETAIL - WD. VENEER @ MID DEPTH ON 2 - 38mm LAYERS A201
PROVIDE PERIMETER SHADOW A201 A201 A601
OF HD STYROFOAM ON 200mm 14
A201 SCALE: 1 : 10 BEAD TO FINISH GYPSUM W1 W1 COMPACTED GRANULAR 'A' FILL (TYP) W1 A1201

Description
BOARD TO 13mm FROM WOOD 1 8 W1 W1
(TYP) REFER TO SPEC A201
1

176

176
CREATIVE COMMONS
108
2 RWL
W1
19mm SOLID PINE WOOD SILL, HEAD & JAMB 3
2 101a
VESTIBULE 101b
5
A201
Sim
FLAT SCREEN TV,

2900
H.S.S. COLUMN (TYP) A205

2938

2938
7 EXTENSION TO SUIT DEPTH (MATCH GYPSUM

2642

2642
7 Sim Sim
A201 A201 3 3 101 SEE ELEC.
REFER TO STRUC. DWGS. BOARD FACE) w/ STAIN/VARNISH FINISH ALL 6
A502 A502 2
FOUR SIDES (TYP) BY DIVISION 06 10 00 W1 W1 A201
A701

6mil POLY VAPOUR BARRIER (TYP)

FIBREGLASS/WOOD WINDOW
3 3
13 SYSTEM w/ PERIMETER
13
A1201
WELCOME CENTRE
4 4 102
2419

2419

No.
CAULKING ON BOTH SIDES (TYP) OPEN TO BELOW

9324
REFER TO SPEC

9058
4
A1201
PEEL & STICK MEMBRANE AROUND
5 5 FD

4767
COMPOSITE HORIZ. WOOD ALL OPENINGS CONT. (TYP) WOMEN W/R
SIDING ON 38mm x 89mm VERT. 113 F2b
PEEL & STICK MEMBRANE ON W1
2311

2311
WOOD STRAPPING ON BUILT-UP
4

2021
WOOD COLUMN (TYP) 290 19mm EXT. GRADE PLYWOOD
A901 P2c
FASCIA BOARD CONT. (TYP) W4
FILL VOID WITH RIGID
INSULATION (TYP) E PREFINISHED METAL 6 6 COMMON HALLWAY
CLADDING CONT. TUCK
10629

1100

1184

267 1102
4 UP 4 112 112a STAIR NO.1 UP 102
INTO WINDOW FRAME (TYP) 112b
3 TYP. WINDOW LARGE MID JAMB DETAIL A502 A502 EQ EQ 114
3000

3000
ATTIC AREA W3 RWL
A201 SCALE: 1 : 10
118 3055
1

1524
OFFICE P2c W1
P2c A901
CL

OPEN TO BELOW
W1
CREATIVE COMMONS 19mm SOLID PINE WOOD SILL, HEAD & JAMB 104
FIBREGLASS/WOOD WINDOW 108 EXTENSION TO SUIT DEPTH (MATCH GYPSUM 7 2
7 FD 2
SYSTEM w/ PERIMETER

1110
BOARD FACE) w/ STAIN/VARNISH FINISH ALL MEN W/R CORRIDOR P2c W2

FLOOR PLANS
1120mm HIGH HALF A601 104 A601
CAULKING ON BOTH SIDES (TYP) FOUR SIDES (TYP) BY DIVISION 06 10 00 111 103
REFER TO SPEC PROVIDE ATTIC ACCESS WALL GUARD
3020

3020
DOOR MADE OF 19mm F2b
PLYWOOD ON 38mm x MECH. ROOM MEZZ. (OPEN)
13 102mm CONC SLAB w/ 152mm

7994
13mm EXTERIOR GRADE 1 105 UNIVERSAL WR
25937

26274
89mm WOOD FRAMING, x 152mm - M.W. 13.3 x M.W.

7987
8207
PLYWOOD SHEATHING (TYP) 117 115 A1201 105
INCLUDING HARDWARE 13.3 W.W.M. @ MID DEPTH ON P2c FD
8 8 1500 U2c

273 1000 273

2 - 38mm x 184mm WOOD STUDS 3
200mm COMPACTED
FASTENED TO VERTICAL 2 - 38mm 2 GRANULAR 'A' FILL (TYP) . 103 2

1331
A601 A503 CLOSET A503 DF
PEEL & STICK MEMBRANE ON 19mm x 184mm WOOD POSTS @ EACH
110 P2c STORAGE
x 64mm WOOD FASCIA BOARD CONT. END w/ 3 - SCREWS (TYP) ELECT. ROOM
3550

3550
SERVERY 107

2800
6 106b 1
FASTEN THRU TO STUDS (TYP) 106 FD
1 A1201 116 1 109 1438 3847 1186
A701
FILL VOID WITH RIGID FD U2b

1524
INSULATION (TYP) A502 MEZZ. BRIDGE A502
PREFINISHED METAL W1 109b P2c 109a 106a Tr
116
460

CLADDING CONT. (TYP) RWL

1325 76 1325 130

John R. Park Homestead Heritage Centre

2117 3240 108a
TYP. WINDOW SMALL MID JAMB DETAIL 9

344 1325 76 1325 291 1110 76 1110 291 1325 76 1325

2 W1 P2c W1

915 County Road 50, Essex, Ontario N0R 1G0

PROVIDE 1 HOUR FIRE
A201 SCALE: 1 : 10 6
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

3
3075

3075
RESISTANCE RATING - REFER
TO CODE COMPLIANCE PLAN A1201 A601
ALL PREFINISHED WOOD PANELS
MUST HAVE PERIMETER 'J' MOULDING W1 W1
BY PANEL SUPPLIER (TYP) PROVIDE PERIMETER SHADOW
10 10

372
13mm EXT. GRADE PLYWOOD BEAD TO FINISH GYPSUM
SHEATHING CONT. 38mmx140mm BOARD TO 13mm FROM WOOD W2 2 FLAT SCREEN TV, 2
WD. STUDS @ 400mm O.C. (TYP) (TYP) REFER TO SPEC
2472

2472

2134
9316
CREATIVE COMMONS A602 SEE ELEC. A602

8981
19mm SOLID PINE WOOD SILL, HEAD & JAMB OPEN TO BELOW CREATIVE COMMONS

8976
108 W1
6mil POLY VAPOUR BARRIER (TYP) EXTENSION TO SUIT DEPTH (MATCH GYPSUM W2 108
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
7 Sim
11 11

372
FILL VOID w/ R20 BATT INSULATION (TYP)
A201 13 FOUR SIDES (TYP) BY DIVISION 06 10 00 2 2
A502 A502

1325 76 1325
13mm EXT. GRADE PLYWOOD 2 - LAYERS 16mm EXTERIOR GRADE W1 W1
SHEATHING CONT. (TYP) PLYWOOD SHEATHING (TYP) REFER
3092

3092
1 2 3 2 Sim
TO DETAIL 9 ON DWG. A603 A201 A201 A201 5121
A201
13 1 1

344 1325
FIBREGLASS/WOOD WINDOW W1 A503
W1 W1 A503
SYSTEM w/ PERIMETER 11
12 12
181

181

522
CAULKING ON BOTH SIDES (TYP) A603 RWL
50mm RIGID INSULATION (TYP) REFER TO SPEC

AIR BARRIER CONT. (TYP) H.S.S. COLUMN (TYP) 13 W1 W1 W1 13 W1 W1

1325 1325
4
FROST SLAB CONSTRUCTION:
102mm CONC SLAB w/ 152mm x

ERCA
3305 ± W1 W1 W2 A201
REFER TO STRUC. DWGS. NOTE: 152mm - M.W. 13.3 x M.W. 13.3 W.W.M.
CLEAR AIR SPACE (TYP) WHEN THE GENERAL CONTRACTOR IS LOCATING @ MID DEPTH ON 2 - 38mm LAYERS
PEEL & STICK MEMBRANE AROUND 81 6920 MS-2 5799 191 3924 92 OF HD STYROFOAM ON 200mm
7052 1325 76 1325 290 1325 1416 THE BUILDING THEY SHALL REFERENCE FROM
PERIMETER CAULKING CONT. (TYP) 290 ALL OPENINGS CONT. (TYP)
THE EXISTING GIFT SHOP DUE TO SPATIAL 12991 2509 1506 COMPACTED GRANULAR 'A' FILL (TYP)
COMPOSITE HORIZ. WOOD PEEL & STICK MEMBRANE ON SEPARATION; REFER TO SITE PLAN
17006 FROST SLAB Drawn By Checked By
SIDING ON 19mm x 89mm VERT.
WOOD STRAPPING @ 610mm O.C.
19mm EXT. GRADE PLYWOOD A D F H Ai Ai
D FASCIA BOARD CONT. (TYP)
N
6/1/2020 8:37:17 AM

ON 51mm GALV. METAL HORIZ. 'Z'

GIRTS @1220mm O.C. MAX. (TYP)
PREFINISHED METAL A N D F H Project No
CLADDING CONT. TUCK OVERALL MEZZANINE 2020
INTO WINDOW FRAME (TYP) FIRST FLOOR PLAN
SCALE: 1 : 100
1 TYP. WINDOW JAMB DETAIL - METAL CLADDING SCALE: 1 : 100 THIS LINE IS 4" LONG
Sheet No
A201 SCALE: 1 : 10
THE INFORMATION INCLUDED IN THIS ELECTRONIC DRAWING FILE IS PROTECTED BY COPYRIGHT. UNAUTHORIZED USE OF THIS FILE WITHOUT THE WRITTEN PERMISSION OF ARCHITECTTURA INC. ARCHITECTS IS PROHIBITED.
ARCHITECTTURA INC. ARCHITECTS IS RESPONSIBLE ONLY FOR INFORMATION SHOWN ON A MECHANICAL REPRODUCTION OF THIS DRAWING FILE THAT HAS BEEN SIGNED AND SEALED BY A REGISTERED ARCHITECT EMPLOYED BY THE FIRM.
THIS DRAWING SHEET IS 36"X24" IN SIZE. IT IS RECOMMENDED THAT ANY REPRODUCTION, ELECTRONIC OR OTHERWISE, BE TO THE SAME SHEET SIZE
TO ENSURE THE ACCURACY OF DRAWING SCALES DEPICTED ON THIS SHEET. THIS DRAWING IS NOT TO BE SCALED - USE FIGURED DIMENSIONS ONLY.
A201
ROOM FINISH SCHEDULE FLOOR FINISH LEGEND WALL FINISHES - GENERAL NOTES
WALL FINISH LEGEND
FLOOR WALL CEILING 1. ALL AREA w/ S-1 AND S-3 WALL FINISHES
No. ROOM NAME MATERIAL BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS CONTINUOS TO UNDERSIDE OF T.O. WALL PLATE
EXPOSED TINTED CONCRETE
101 VESTIBULE FF1 RB GYP BD PT-1 2650 CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD WOOD SIDING (FF1)
150mm 2. ALL WALLS AND EXPOSED SURFACES INCLUDING
102 WELCOME CENTRE FF1 RB GYP BD SIDING TYPE 1 & 3, & PT-1 EXPOSED-TECTUM CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD - RB ON PLYWD BACKER GYPSUM BOARD BULKHEADS/CEILINGS AND ROOF
(S-1)
103 CORRIDOR FF1 RB GYP BD SIDING TYPE 1& 2, & PT-1 EXPOSED-TECTUM CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD - RB ON PLYWD BACKER DECK TO BE PAINTED PT-1 U.N.O.
104 OFFICE FF1 RB GYP BD PT-1 SUSPENDED PT-1 2450 CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD
105 UNIVERSAL WR FF2 TB GYP BD PT-1 SUSPENDED & GYP BD PT-1 2450 PAINT ALL EXPOSED PRE-ENGINEERED WOOD 3. ALL EXPOSED WOOD AND TRUSSES TO BE
180 Eugenie Street West
PAINTED PT-2 Windsor, ON N8X 2X6
106 ELECT. ROOM FF1 RB GYP BD PT-1 EXPOSED DECK PT-1 2650 CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD PORCELAIN FLOOR TILE 519.258.1390
107 STORAGE FF1 RB GYP BD PT-1 EXPOSED DECK PT-1 2650 CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD WOOD SIDING 300mm X 600mm 4. ALL H.M. DOOR FRAMES TO BE PT-3 U.N.O.
108 CREATIVE COMMONS FF1 RB GYP BD SIDING TYPE 1 & PT-1 EXPOSED-TECTUM 2450 CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD - RB ON PLYWD BACKER 150mm (FF2)
109 SERVERY FF2 TB GYP BD PT-1 SUSPENDED & GYP BD PT-1 PAINT ALL EXPOSED PRE-ENGINEERED WOOD (S-2) 5. REFER TO WASHROOM ELEVATIONS FOR
110 CLOSET FF1 RB GYP BD PT-1 EXPOSED DECK PT-1 2650 CONC w/ SEALER FINISH - PAINT ALL EXPOSED PRE-ENGINEERED WOOD WASHROOM WALLS TO RECEIVE PORCELAIN WALL
TILE CAPPED w/ ALUMINUM EDGE AT EXPOSED ENDS.
111 MEN W/R FF2 TB GYP BD SUSPENDED & GYP BD PT-1 PAINT ALL EXPOSED PRE-ENGINEERED WOOD
112 COMMON HALLWAY FF1 TB GYP BD PT-1 SUSPENDED & GYP BD 2450 PAINT ALL EXPOSED PRE-ENGINEERED WOOD VINYL COMPOSITE TILE
113 WOMEN W/R FF2 TB GYP BD PT-1 SUSPENDED & GYP BD PT-1 2450 PAINT ALL EXPOSED PRE-ENGINEERED WOOD STAINED WOOD PANEL 300mm X 300mm
114 STAIR NO.1 RUBBER TREAD GYP BD PT-1 EXPOSED-TECTUM PAINT ALL EXPOSED PRE-ENGINEERED WOOD
(S-3) (FF3)
115 MEZZ. (OPEN) FF3 RB GYP BD PT-1 EXPOSED-TECTUM PAINT ALL EXPOSED PRE-ENGINEERED WOOD This drawing is not to be used for
construction unless it is countersigned
116 MEZZ. BRIDGE FF3 - EXPOSED-TECTUM PAINT ALL EXPOSED PRE-ENGINEERED WOOD by the Project Architect
117 MECH. ROOM FF4 - PROVIDE 8'x8' PLYWOOD BACKER ON ONE WALL FOR MECH EQ. REFER TO MECH FOR LOCATION.
118 ATTIC AREA FF4 - EXPOSED PLYWOOD FLOOR FINISH PLAN - GENERAL NOTES Issued For (YYMMDD)
TILE (FF4) TENDER 2020.06.01
(S-4) 1. ALL AREAS w/ PORCELAIN VINYL TILE FLOORING
(FF2) TO RECEIVE RUBBER BASE (RB) AS SPECIFIED.

2. ALL AREAS TO RECEIVE RUBBER BASE (RB) AS

SPECIFIED EXCEPT AREAS w/ EXPOSED TYLE ( FF2-
CARPET FF3)
(FF5)
3. PROVIDE A TRANSITION STRIP AT ALL FLOORING
CHANGES.

Date
Revision Schedule
1
A204 1 VESTIBULE
VESTIBULE A204 101

Description
101
2
A204 2
EXTERIOR

S -3
A204
SIDING
WELCOME CENTRE
WELCOME CENTRE 102
102

FF1

WOMEN W/R
WOMEN W/R 113 FF2
113
ATTIC AREA ATTIC AREA

No.
S -1
118 118 FF5

S-1
REF TO INT ELEV A203

COMMON HALLWAY
COMMON HALLWAY 112
UP 112
UP UP

WALL & FLOOR FINISH PLANS

UP S-1 FF2
S -2

REF TO INT ELEV A203 RUBBER TREADS RUBBER TREADS

ON STAIRS OFFICE ON STAIRS
OFFICE FF1 104
E
104
S -1

MEN W/R FF1

MEN W/R - A701 - 111
111 FF4
MEZZ. (OPEN) MEZZ. (OPEN) D -
115 115 FF2 UNIVERSAL WR
UNIVERSAL WR
S -1

105 A A701 FF2

MECH. ROOM 105 MECH. ROOM
117 117 FF3
B

.
. CLOSET FF-1
110
ELECT. ROOM STORAGE SERVERY
SERVERY 109 ELECT. ROOM FF1 FF1
109 106 107
MEZZ. BRIDGE MEZZ. BRIDGE 106
FF2
116 116 FF3

?
S -1 S -1

John R. Park Homestead Heritage Centre

CREATIVE COMMONS
CREATIVE COMMONS 108

915 County Road 50, Essex, Ontario N0R 1G0

3 108
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

A204 3 FF1
A204
S -1

NOTE:
1. ALL REMAINING GYPSUM TO BE PAINTED.
2. ALL EXPOSED TRUSSES TO BE PAINTED.
3. ALL EXPOSED WOOD SUCH AS WINDOW
TRIM, RAILINGS, FIREPLACE PANELS, AND
MISC TRIM TO BE STAINED AND CLEAR
4 COATED.
A204 4
A204
S -1

3 3
A203 A203

4 MEZZANINE OVERALL WALL FINISH PLAN 3 FIRST FLOOR OVERALL WALL FINISH PLAN 2 MEZZANINE OVERALL FLOOR FINISH PLAN 1 FIRST FLOOR OVERALL FLOOR FINISH PLAN

ERCA
A203 SCALE: 1 : 100 A001 SCALE: 1 : 100 A203 SCALE: 1 : 100 A001 SCALE: 1 : 100

Drawn By Checked By
Ai Ai
6/1/2020 8:37:21 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

180 Eugenie Street West

Windsor, ON N8X 2X6
519.258.1390

T/O RIDGE BEAM

8392 R-20 INSULATION BATTS w/
6mil POLY VAPOUR BARRIER

TECTUM PANELS FASTENED

DIRECTLY TO SIP PANELS CJ CJ This drawing is not to be used for
construction unless it is countersigned
by the Project Architect
12.7mm GYPSUM BOARD (TYP)
13
Issued For (YYMMDD)
PREFINISHED WOOD PANEL MAX. TENDER 2020.06.01
ALL EXPOSED WOOD AND BELOW w/ PERIMETER 'J' MOULDING ZINC CONTROL JOINT (TYP)
TRUSSES TO BE PAINTED BY PANEL SUPPLIER (TYP) REFER TO SPEC DIV. 09
1
PT-2 (TYP) 19mm SOLID PINE WOOD SILL, HEAD & JAMB
A203 PAINT JOINT TO WOOD PANEL
EXTENSION TO SUIT DEPTH (MATCH GYPSUM
BOARD FACE) w/ STAIN/VARNISH FINISH ALL HEIGHT TO MATCH 'J'
FOUR SIDES (TYP) BY DIVISION 06 10 00 MOULDING COLOUR (TYP)

ALL EXPOSED SURFACES

INCLUDING ROOF DECK,
1 TYP. INTERIOR CONTROL JOINT - GYPSUM
GYPSUM TO BE PAINTED PT-1 7 A203 SCALE: 1 : 2
(TYP) A201

CJ CJ

1066
SIDING TYPE S-2
MEZZANINE
2910

466 150
150mm SOLID WOOD BATTEN-CEDAR

Date
T.O. WALL PLATE
2650 SIDING TYPE S-1

2040

2184
375 695

Revision Schedule
SIDING TYPE S-1

610

Description
FIRST FLOOR
0
100mm RUBBER BASE CONT. ON 13mm EXTERIOR
GRADE PLYWOOD BACKER CONT. (TYP)

2 INTERIOR ELEVATION - WEST HALLWAY WALL SEPARATE PRICE NO.3 & NO.4
SCALE: 1 : 50 DELETE CANEXEL SIDING & REPLACE w/
SAGIPER NORTH AMERICA SIDING (TYP)
REFER TO SPEC.

No.
1 2 3 4 5 6 7 8 9 10 11 12 13

INTERIOR ELEVATIONS
T/O RIDGE BEAM
8392

TECTUM PANELS FASTENED

DIRECTLY TO SIP PANELS

CJ CJ
ALL EXPOSED WOOD AND
TRUSSES TO BE PAINTED
19mm SOLID PINE WOOD SILL, HEAD & JAMB

John R. Park Homestead Heritage Centre

PT-2 (TYP)
EXTENSION TO SUIT DEPTH (MATCH GYPSUM
BOARD FACE) w/ STAIN/VARNISH FINISH ALL

915 County Road 50, Essex, Ontario N0R 1G0

FOUR SIDES (TYP) BY DIVISION 06 10 00
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

ALL EXPOSED SURFACES

INCLUDING ROOF DECK,
GYPSUM TO BE PAINTED PT-1
(TYP)

MEZZANINE
2910
T.O. WALL PLATE
2650

13mm FINISHED PLYWOOD

STAINED & VARNISHED (TYP)
SIDING TYPE S-1

FIREPLACE
LOCATION SIDING TYPE S-1

FIRST FLOOR

ERCA
0

100mm RUBBER BASE CONT. ON 13mm EXTERIOR 100mm RUBBER BASE CONT. (TYP)
GRADE PLYWOOD BACKER CONT. (TYP)
Drawn By Checked By
3 INTERIOR ELEVATION - EAST HALLWAY WALL SEPARATE PRICE NO.3 & NO.4 Ai Ai
6/1/2020 8:37:24 AM

DELETE CANEXEL SIDING & REPLACE w/

A202 SCALE: 1 : 50
SAGIPER NORTH AMERICA SIDING (TYP)
Project No
REFER TO SPEC. 2020
THIS LINE IS 4" LONG
Sheet No

180 Eugenie Street West

Windsor, ON N8X 2X6
519.258.1390

T/O RIDGE BEAM

8392

TYPICAL WINDOW JAMB DETAIL

TECTUM PANEL
This drawing is not to be used for
ALL EXPOSED SURFACES construction unless it is countersigned
by the Project Architect
INCLUDING ROOF DECK,
GYPSUM TO BE PAINTED PT-1
TECTUM PANEL (TYP) Issued For (YYMMDD)
TENDER 2020.06.01
ALL EXPOSED WOOD AND
ALL EXPOSED SURFACES TRUSSES TO BE PAINTED
INCLUDING ROOF DECK, PT-2 (TYP)
GYPSUM TO BE PAINTED PT-1
(TYP) 19mm SOLID PINE WOOD SILL, HEAD & JAMB
EXTENSION TO SUIT DEPTH (MATCH GYPSUM
ALL EXPOSED WOOD AND BOARD FACE) w/ STAIN/VARNISH FINISH ALL
TRUSSES TO BE PAINTED FOUR SIDES (TYP) BY DIVISION 06 10 00
PT-2 (TYP)

MEZZANINE
2910

T.O. WALL PLATE

2650

Date
Welcome to The Stephanie & Barry Zekelman TV
Foundation Welcome Centre

SIDING TYPE S-1

Revision Schedule
FIRST FLOOR
0

Description
100mm RUBBER BASE CONT. ON 13mm EXTERIOR
GRADE PLYWOOD BACKER CONT. (TYP) 100mm RUBBER BASE CONT. (TYP)

SEPARATE PRICE NO.3 & NO.4

2 INTERIOR ELEVATION - SOUTH WELCOME CENTRE WALL DELETE CANEXEL SIDING & REPLACE w/ 1 INTERIOR ELEVATION - NORTH WELCOME CENTRE WALL
SAGIPER NORTH AMERICA SIDING (TYP)
A202 SCALE: 1 : 50
REFER TO SPEC. A202 SCALE: 1 : 50

No.
F

E CL D C B A A B C D CL E F

INTERIOR ELEVATIONS
T/O RIDGE BEAM
8392
TECTUM PANEL

TYPICAL WINDOW JAMB DETAIL ALL EXPOSED SURFACES

INCLUDING ROOF DECK,
ALL EXPOSED SURFACES GYPSUM TO BE PAINTED PT-1
INCLUDING ROOF DECK, (TYP)
GYPSUM TO BE PAINTED PT-1
(TYP) ALL EXPOSED WOOD AND
TRUSSES TO BE PAINTED
ALL EXPOSED WOOD AND PT-2 (TYP)
TRUSSES TO BE PAINTED
PT-2 (TYP) STAIN & VARNISH WOOD
TOP PLATE, BOTTOM PLATE
& SPINDLE BALUSTRADES @
100mm O.C. MAX. (TYP)

John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

MEZZANINE
2910

T.O. WALL PLATE

2650

19mm SOLID PINE WOOD SILL, HEAD & JAMB

EXTENSION TO SUIT DEPTH (MATCH GYPSUM
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
FOUR SIDES (TYP) BY DIVISION 06 10 00
SIDING TYPE S-1

SIDING TYPE S-1 SIDING TYPE S-1

FIRST FLOOR

ERCA
0
100mm RUBBER BASE CONT. ON 13mm EXTERIOR
100mm RUBBER BASE CONT. (TYP) 100mm RUBBER BASE CONT. ON 13mm EXTERIOR GRADE PLYWOOD BACKER CONT. (TYP)
GRADE PLYWOOD BACKER CONT. (TYP)

4 INTERIOR ELEVATION - SOUTH CREATIVE COMMONS WALL 3 INTERIOR ELEVATION - NORTH CREATIVE COMMONS WALL
SEPARATE PRICE NO.3 & NO.4 Drawn By Checked By
A202 SCALE: 1 : 50 SEPARATE PRICE NO.3 & NO.4 A202 SCALE: 1 : 50 DELETE CANEXEL SIDING & REPLACE w/ Ai Ai
6/1/2020 8:37:28 AM

DELETE CANEXEL SIDING & REPLACE w/ SAGIPER NORTH AMERICA SIDING (TYP)
REFER TO SPEC. Project No
SAGIPER NORTH AMERICA SIDING (TYP)
REFER TO SPEC. 2020
THIS LINE IS 4" LONG
Sheet No

MIN. 305
SEALANT (TYP.) EXHAUST PIPE (TYP.) URETHANE INSULATION ON INNER SEALANT AS REQUIRED
PEEL & STICK MEMBRANE SHEATHING ON 38mm x 184mm ROOF
PREMOLDED & PRE-FINISHED COLLAR TIE AROUND PIPE (TYP.) SIDE (TYP.) - REFER TO SPECS.
ON 13mm EXTERIOR JOIST @ 400mm O.C. w/ VENTED
METAL COUNTER FLASHING INTEGRAL DECK FLANGE SET ROOFING SYSTEM - REFER GRADE PLYWOOD PREFINISHED SOFFIT (TYP)
SLEEVE INTO MASTIC BED TO SPECS. SHEATHING CONT. (TYP) 180 Eugenie Street West
Windsor, ON N8X 2X6
6mm BENT PLATE SLEEVE 6mm PRESSURE TREATED PLYWOOD 519.258.1390
(TYP.) ON 25mm x 25mm PRESSURE TREATED PREFINISHED METAL
WOOD BLOCKING & 19mm RIGID FLASHING INTO SHROUD (TYP) FILL VOID w/ BATT INSULATION (TYP)
INSULATION IN CAVITY BUILT-UP CURB
ROOF MEMBRANE - REFER TO SPECS PREFINISHED ALUM
MECHANICAL PENETRATION RWL w/ SHROUD (TYP) 6mil POLY VAPOUR BARRIER (TYP)
THROUGH SIP PANEL AS PER PROVIDE 13mm WIDE STRIP OF
MANUF. REC'D DETAILS MEMBRANE FLASHING PREFINISHED METAL 12.7mm GYPSUM BOARD (TYP)
w/ LAP SEALANT FULLY ADHERED FASCIA CONT. (TYP)
13mm EXTERIOR GRADE This drawing is not to be used for
13mm EXTERIOR GRADE PLYWOOD SHEATHING (TYP) construction unless it is countersigned
by the Project Architect
PLYWOOD SHEATHING ON
MECHANICAL PENETRATION 38mm x 184mm WOOD FRAMING PREFINISHED ALUMINUM WINDOW
THROUGH SIP PANEL AS PER MANUF. REFER TO STRUC. DWGS. (TYP) SYSTEM (TYP.) w/ PERIMETER Issued For (YYMMDD)

REC'D DETAILS CAULKING ON BOTH SIDES CONT. TENDER 2020.06.01

113 151 127
PREFINISHED VENTED SOFFIT
CONT. (TYP) REFER TO SPECS.
1 TYPICAL ROOF VENT DETAIL 2 TYPICAL ROOF PENETRATION DETAIL 3 TYP. SCUPPER DETAIL
SCALE: 1 : 10 SCALE: 1 : 10 A201 SCALE: 1 : 10

B C CL E F
G

Date
3 LOW OVER FLOW SCUPPER CONNECTED TO
RWL w/ PREFINISHED METAL SHROUD (TYP)
1 A205

Revision Schedule
LINE OF WALL
BELOW (TYP)

Description
3
4

No.
6

8
.

ROOF PLAN
APPROX. LOC OF VENT STACK
PENETRATIONS THROUGH ROOF, SEE
TYP. DETAIL, COORDINATE SANITARY
VENTS W/ MECH.
OVER FLOW SCUPPER CONNECTED
TO RWL w/ SHROUD (TYP)
9
LINE OF WALL
BELOW (TYP)

John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

12
13 OVER FLOW SCUPPER CONNECTED 3
SIM
TO RWL w/ SHROUD (TYP) A205

A D H

ERCA
N
ROOF PLAN
SCALE: 1 : 100
Drawn By Checked By
Ai Ai
6/1/2020 8:37:30 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

ACOUSTICAL CEILING (ACT-1)

ACT-1
24"X24" Acoustical Ceiling Tile
MEZZANINE
w/ suspension system
2910 (Refer to Specifications and Reflected Ceiling Plans)

180 Eugenie Street West

TECTUM CEILING PANEL Windsor, ON N8X 2X6
T.O. WALL PLATE 24"X48" Acoustical Ceiling Panels
519.258.1390
2650 TECTUM
fastened to u/s insulated roof panels
(Refer to Specifications and Reflected Ceiling Plans)

200
340
GYPSUM BOARD CEILING (C-1)
ACT-1 C-1
1/2" Gypsum board
2450 w/ suspension system
(Refer to Specifications and Reflected Ceiling Plans) This drawing is not to be used for
construction unless it is countersigned
B-1 by the Project Architect
TYP. BULKHEAD CONSTRUCTION
2307 12.7mm GYPSUM BOARD ON
Issued For (YYMMDD)
38mm x 38mm WD. STUDS @ GYPSUM BOARD BULKHEAD (B-1)
500 B-1 TENDER 2020.06.01
400mm O.C. (TYP) 1/2" Gypsum board on metal framing
(Refer to Details and Reflected Ceiling Plans)

1 TYP. BULKHEAD SECTION

A301 SCALE: 1 : 10

Date
Revision Schedule

Description
PREFINISHED VENTED SOFFIT
PREFINISHED METAL SOFFIT CONT. (TYP) REFER TO SPECS.
CONT. (TYP) REFER TO SPECS.

VESTIBULE
PREFINISHED VENTED SOFFIT 101 TECTUM PANELS ON AN
CONT. (TYP) REFER TO SPECS. ANGLE W/ CEILING, SEE
SECTIONS FOR

No.
DIMENSIONS

TECTUM PANELS ON AN WELCOME CENTRE ALL EXPOSED SURFACES

ANGLE W/ CEILING, SEE 102 INCLUDING CEILING, GYPSUM
TECTUM 500
SECTIONS FOR TO BE PAINTED PT-1 (TYP)
DIMENSIONS
B-1 ACT-1 TECTUM

FIRST FLOOR REFLECTED

2307 2450
WOMEN W/R
ATTIC AREA 113
118
ALL EXPOSED WOOD
COMMON HALLWAY SHEATHING AND TRUSSES
DISPLAY CABINETS w/ LED 112 TO BE PAINTED PT-2 (TYP)
RECESSED PUCK LIGHTING CORRIDOR
(TYP) REFER TO ELEC. DWGS. ACT-1 103
2450

CEILING PLAN
B-1 OFFICE 1/2" GYP @ U/S OF
104 STAIRS, SEE 2/A901
2307 B-1 ACT-1
2307 2450
ACT-1 500
MECH. ROOM MEZZ. (OPEN) 1 2450
117 115 A301
MEN W/R
B-1
111
2307
UNIVERSAL WR
105 ACT-1
SERVERY C-1 B-1
B-1 109 2450
2307 ELECT. ROOM

John R. Park Homestead Heritage Centre

2307 ACT-1
106
2450
PREFINISHED VENTED SOFFIT

915 County Road 50, Essex, Ontario N0R 1G0

C-1 CONT. (TYP) REFER TO SPECS.
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

TECTUM PANELS ON AN ALL EXPOSED SURFACES

ANGLE W/ CEILING, SEE INCLUDING CEILING, GYPSUM OPEN
THRU
SECTIONS FOR TO BE PAINTED PT-1 (TYP)
DIMENSIONS CREATIVE COMMONS
108

TECTUM PANELS ON AN
ANGLE W/ CEILING, SEE PREFINISHED METAL
TECTUM TECTUM SECTIONS FOR TECTUM TECTUM OPEN CLADDING ON PEEL &
THRU
DIMENSIONS STICK MEMBRANE TO
COVER JOIST w/
PERIMETER CAULKING
CONT. (TYP)
ALL EXPOSED WOOD
SHEATHING AND TRUSSES
TO BE PAINTED PT-2 (TYP) OPEN
THRU

ERCA
PREFINISHED VENTED SOFFIT
CONT. (TYP) REFER TO SPECS. OPEN THRU
Drawn By Checked By
PREFINISHED METAL SOFFIT Ai Ai
6/1/2020 8:37:33 AM

CONT. (TYP) REFER TO SPECS.

2 MEZZANINE REFLECTED CEILING PLAN 3 FIRST FLOOR REFLECTED CEILING PLAN Project No

A203 SCALE: 1 : 100 A001 SCALE: 1 : 100 2020

THIS LINE IS 4" LONG
Sheet No

SEPARATE PRICE NO.2 3 MS-2 - PREFIN. METAL SIDING/FLASHING/SOFFIT/GUTTER & RWL'S

DELETE ASPHALT SHINGLES & REPLACE
4 ASPHALT SHINGLES
w/ BORAL STEEL COATED ROOFING (TYP)
REFER TO SPEC. 180 Eugenie Street West
5 PREFIN. ALUMINUM STOREFRONT WINDOWS Windsor, ON N8X 2X6
519.258.1390

This drawing is not to be used for

construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

TENDER 2020.06.01

CL
H G F E D C B A 13 12 11 10 9 8 7 6 5 4 3 2 1

3 2 3
T/O RIDGE BEAM T/O RIDGE BEAM
8392 8392
12 3 12

Date
8 8
1 1 PREFINISHED ALUM. RWL. w/
3 3 PRECAST CONC. SPLASH 4
W1 W1 1
3 3 PADS (TYP) REFER TO SPEC.

9 CONTROL JOINT w/ 'J'

CJ MOULDING CONT. (TYP)
W1 A603 W1
8750

8750
CJ PREFINISHED (LARGE)

Revision Schedule
1 3
ALUM. GUTTER CONT. (TYP)
MEZZANINE OVER FLOW SCUPPER CONNECTED TO REFER TO SPEC. MEZZANINE
2910 W1 W1 RWL w/ PREFINISHED METAL SHROUD (TYP) W1 W1 W2 W2 W1 W1 2910

Description
T.O. WALL PLATE T.O. WALL PLATE
2650 9 CJ CJ 2650
W1 W1 W1 W1 W1 A603 W1 1
HEATPUMP (TYP)
W2 CONTROL JOINT w/ 'J'
REFER TO MECH DWGS.
MOULDING CONT. (TYP)
W1 W1 W1 W1 W1 W1

754
FIRST FLOOR FIRST FLOOR
0 0
5

CONNECT PREFINISHED PREFINISHED ALUM. RWL. w/

No.
ALUM. RWL. TO SCUPPER PRECAST CONC. SPLASH
(TYP) REFER TO SPEC. PADS (TYP) REFER TO SPEC.

1 NORTH ELEVATION 2 EAST ELEVATION

SCALE: 1 : 100 SCALE: 1 : 100

EXTERIOR ELEVATIONS
CL
A B C D E F G H 1 2 3 4 5 6 7 8 9 10 11 12 13

3 2 3

T/O RIDGE BEAM T/O RIDGE BEAM

8392 1 3 8392
12 12
4
8 8
1 3 1

John R. Park Homestead Heritage Centre

PREFINISHED ALUM. RWL. w/
9

915 County Road 50, Essex, Ontario N0R 1G0

3 3 POLY VINYL SPLASH PAD
W1 W1 W1 A603 W1
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

CONTROL JOINT w/ 'J' (TYP) REFER TO SPEC.

PREFINISHED (LARGE)
MOULDING CONT. (TYP) 1 ALUM. GUTTER CONT. (TYP)
CJ W1 W1 W1 W1 W1 REFER TO SPEC.
8750

8750
1
OVER FLOW SCUPPER CONNECTED TO 3
MEZZANINE RWL w/ PREFINISHED METAL SHROUD (TYP)
1164
3 5 MEZZANINE
W1 W1 W1 2910
2910
T.O. WALL PLATE T.O. WALL PLATE
2650 CJ CJ 2650
9 9
W1 A603 W1 W2 1 A603 W1

W1 W1 W2 W1
FIRST FLOOR FIRST FLOOR
0 0
W1 W1 3

CONTROL JOINT w/ 'J'

HEAT PUMP (TYP) PREFINISHED ALUM. RWL. w/
MOULDING CONT. (TYP)
REFER TO MECH DWGS. PRECAST CONC. SPLASH
PADS (TYP) REFER TO SPEC.

ERCA
3 SOUTH ELEVATION 4 WEST ELEVATION
Drawn By Checked By
SCALE: 1 : 100 SCALE: 1 : 100
Ai Ai
6/1/2020 8:37:38 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

180 Eugenie Street West

Windsor, ON N8X 2X6
519.258.1390

ALL EXPOSED WOOD AND

TRUSSES TO BE PAINTED
This drawing is not to be used for
PT-2 (TYP) construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

TENDER 2020.06.01

ATTIC AREA MECH. ROOM ALL EXPOSED SURFACES

118 117 INCLUDING CEILING, GYPSUM
6 Sim TO BE PAINTED PT-1 (TYP)
A603

MEZZANINE
2910

T.O. WALL PLATE

2650

CREATIVE COMMONS
13 108
A603
VESTIBULE WOMEN W/R COMMON HALLWAY MEN W/R SERVERY
101 113 112 111 109

6
A1201

Date
FIRST FLOOR
0
12
A603 100mm TILE BASE CONT. (TYP) 100mm RUBBER BASE CONT. (TYP)

Revision Schedule

Description
1 BUILDING SECTION
A201 SCALE: 1 : 50

No.
1 2 3 4 5 6 7 8 9 10 11 12 13

BUILDING SECTIONS
ALL EXPOSED SURFACES
INCLUDING CEILING, GYPSUM
TO BE PAINTED PT-1 (TYP) 19mm SOLID PINE WOOD SILL, HEAD & JAMB
EXTENSION TO SUIT DEPTH (MATCH GYPSUM
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
MEZZ. (OPEN) FOUR SIDES (TYP) BY DIVISION 06 10 00
115

TECTUM PANEL

John R. Park Homestead Heritage Centre

MEZZANINE

915 County Road 50, Essex, Ontario N0R 1G0

2910
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

T.O. WALL PLATE

2650

ALL EXPOSED WOOD AND

TRUSSES TO BE PAINTED PT-2 CREATIVE COMMONS
(TYP) WELCOME CENTRE OFFICE 108
102 104 UNIVERSAL WR ELECT. ROOM
2450

105 106

FIRST FLOOR
0
100mm RUBBER BASE CONT.
100mm RUBBER BASE CONT. ON 13mm EXTERIOR 100mm TILE BASE CONT. (TYP)
(TYP) 100mm RUBBER BASE CONT. (TYP)
GRADE PLYWOOD BACKER CONT. (TYP)

ERCA
Drawn By Checked By

2 BUILDING SECTION Ai Ai
6/1/2020 8:37:42 AM

Project No
A201 SCALE: 1 : 50
2020
THIS LINE IS 4" LONG
Sheet No

180 Eugenie Street West

ALL EXPOSED WOOD AND Windsor, ON N8X 2X6
180 4 TRUSSES TO BE PAINTED 519.258.1390
0 A601 PT-2 (TYP)
AP
PR
OX 12 12
.
ALL EXPOSED SURFACES 00 .
42 8 8
INCLUDING CEILING, GYPSUM OX
TO BE PAINTED PT-1 (TYP) PPR ALL EXPOSED DUCTWORK
A
TO HAVE PAINT FIN.
12
TECTUM ACOUSTIC PANELS FASTENED
TO U/S OF ROOF, REFER TO SPECS & ALL EXPOSED SURFACES
8 This drawing is not to be used for
REFLECTED CEILING PLAN INCLUDING ROOF DECK, construction unless it is countersigned

PROVIDE ATTIC ACCESS GYPSUM TO BE PAINTED PT-1 by the Project Architect

EXPOSED PRE-ENGINEERED (TYP)
WD TRUSSES W/ PAINT FIN.
DOOR MADE OF 19mm
ALL EXPOSED DUCTWORK INSTALL 38mm x 184mm WOOD Issued For (YYMMDD)
PLYWOOD ON 38mm x
TO HAVE PAINT FIN. FRAMING MIN. 2 - LOCATIONS 750 STAIN & VARNISH WOOD TENDER 2020.06.01
89mm WOOD FRAMING,
AS SHOWN FASTENED TOP PLATE, BOTTOM PLATE
12 MEZZ. BRIDGE INCLUDING HARDWARE
BETWEEN TRUSSES (TYP.) DOOR & SPINDLE BALUSTRADES @
116 MEZZ. BRIDGE
100mm O.C. MAX. (TYP)
1
8
A 116
F G H
A603
A F G H

DOOR
1000

GUARDRAIL
MEZZ. (OPEN)

1120
MECH. ROOM 115
117
MEZZANINE

300
2910
T.O. WALL PLATE
2650

STAIN & VARNISH WOOD SPINDLE INSTALL 38mm x 184mm WOOD

BALUSTRADES @ 100mm O.C. FRAMING MIN. 2 - LOCATIONS
CREATIVE COMMONS MAX. GUARDRAIL (TYP) AS SHOWN FASTENED INSTALL 38mm x 184mm WOOD
108 BETWEEN TRUSSES (TYP.) FRAMING MIN. 2 - LOCATIONS
7 SERVERY
CREATIVE COMMONS ELECT. ROOM STORAGE AS SHOWN FASTENED
A1201 109
108 106 107 BETWEEN TRUSSES (TYP.)

Date
POLY SPLASH
PAD SIDING TYPE S-1
SIDING TYPE S-1

FIRST FLOOR
0
100mm TILE BASE CONT. (TYP)
100mm RUBBER BASE CONT. ON 13mm EXTERIOR 100mm RUBBER BASE CONT. (TYP)

Revision Schedule
GRADE PLYWOOD BACKER CONT. (TYP)

Description
2 BUILDING SECTION 1 BUILDING SECTION
A201 SCALE: 1 : 50 A201 SCALE: 1 : 50

No.
19
27

B D CL E
B C D 12
CL E
ALL EXPOSED WOOD AND
TRUSSES TO BE PAINTED 8 T/O RIDGE BEAM
PT-2 w/ ACCENT PT-4 (TYP) 8392

BUILDING SECTIONS
ALL EXPOSED WOOD AND
12 12 TRUSSES TO BE PAINTED PT-2
12
ALL EXPOSED SURFACES 8 8 66
00 ALL EXPOSED SURFACES
INCLUDING CEILING, GYPSUM 8 AP INCLUDING CEILING, GYPSUM
PR
TO BE PAINTED PT1 OX TO BE PAINTED PT-1 (TYP)
.

2
A901
TECTUM ACOUSTIC PANELS FASTENED
F
TO U/S OF ROOF, REFER TO SPECS &
REFLECTED CEILING PLAN

ALL EXPOSED DUCTWORK

TO HAVE PAINT FIN. 19mm SOLID PINE WOOD SILL, HEAD & JAMB
EXTENSION TO SUIT DEPTH (MATCH GYPSUM
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
ATTIC AREA FOUR SIDES (TYP) BY DIVISION 06 10 00
118
G H

John R. Park Homestead Heritage Centre

A INSTALL 38mm x 184mm WOOD
F G H

915 County Road 50, Essex, Ontario N0R 1G0

FRAMING MIN. 2 - LOCATIONS
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

AS SHOWN FASTENED
BETWEEN TRUSSES (TYP.) MEZZANINE
1632 2910
T.O. WALL PLATE
2650
STAIR NO.1
114

CREATIVE COMMONS OFFICE TV

COMMON HALLWAY VESTIBULE WELCOME CENTRE
108 104
112 101 102

POLY
SPLASH
PAD FIRST FLOOR
0

100mm TILE BASE CONT. (TYP) 100mm RUBBER BASE CONT. (TYP)
100mm RUBBER BASE CONT. (TYP)

ERCA
Drawn By Checked By
Ai Ai
6/1/2020 8:37:48 AM

1
A602 Project No
4 BUILDING SECTION
3 BUILDING SECTION 2020
A201 SCALE: 1 : 50
THIS LINE IS 4" LONG
A201 SCALE: 1 : 50 Sheet No

ALL EXPOSED SURFACES

INSTALL 38mm x 184mm WOOD FRAMING INCLUDING CEILING, GYPSUM
MIN. 2 - LOCATIONS AS SHOWN TO BE PAINTED PT-1 (TYP)
FASTENED BETWEEN TRUSSES (TYP.)
This drawing is not to be used for
construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

TENDER 2020.06.01

H F A

MEZZANINE
2910
T.O. CANOPY T.O. WALL PLATE
WD. JOISTS
2650

19mm SOLID PINE WOOD SILL, HEAD & JAMB

EXTENSION TO SUIT DEPTH (MATCH GYPSUM
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
CREATIVE COMMONS
FOUR SIDES (TYP) BY DIVISION 06 10 00

2756
108

Date
SIDING TYPE S-1
A603

POLY SPLASH PAD

FIRST FLOOR
0
100mm RUBBER BASE CONT. (TYP) 100mm RUBBER BASE CONT. ON 13mm EXTERIOR
GRADE PLYWOOD BACKER CONT. (TYP)

Revision Schedule

Description
1 BUILDING SECTION
A201 SCALE: 1 : 50

No.
E D C B
T/O RIDGE BEAM
8392
12 12

8 8

BUILDING SECTIONS
ALL EXPOSED SURFACES
INCLUDING CEILING, GYPSUM
TO BE PAINTED PT-1 (TYP)

MEZZ. (OPEN) STAIN & VARNISH WOOD

115 TOP PLATE, BOTTOM PLATE
& SPINDLE BALUSTRADES @
HG F 100mm O.C. MAX. (TYP)
A

HALF WALL
MECH. ROOM

1120
117
P2c
P2c MEZZANINE
2910

John R. Park Homestead Heritage Centre

T.O. WALL PLATE
2650

915 County Road 50, Essex, Ontario N0R 1G0

P2c
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

P2c

UNIVERSAL WR F2c CREATIVE COMMONS CLOSET

105 108 110 7
A1201
DF.

1605

300
FIRST FLOOR
0
100mm TILE BASE CONT. (TYP) 19mm EXTERIOR GRADE
100mm TILE BASE
PLYWOOD ON 2 - 38mm x 89mm

200
CONT. (TYP)
WOOD PLATES CONT. ON
VAPOUR BARRIER (TYP)

LEVEL w/ FIN. FL. - 19mm

EXTERIOR GRADE PLYWOOD 100mm RUBBER BASE CONT. (TYP)
SHEATHING ON 38mm X 184mm
WOOD FLOOR JOISTS @ 16" O.C.

ERCA
Drawn By Checked By
2 BUILDING SECTION Ai Ai
6/1/2020 8:37:51 AM

A201 SCALE: 1 : 50 Project No

2020
THIS LINE IS 4" LONG
Sheet No

STUD TO SIP

19mm x 38mm PERIMETER WOOD

CLOSURE TRIM CONT. (TYP)
180 Eugenie Street West
Windsor, ON N8X 2X6
519.258.1390

F
This drawing is not to be used for
construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

TENDER 2020.06.01

2 Sim
A603

1270 ±

1203
STUD FACE TO SIP FACE

9 Sim
A603
12
19mm x 38mm PERIMETER WOOD
CLOSURE TRIM CONT. (TYP) 8
H

77
TAPERED BLOCKING ON TOP
PLATES CONT. TO MATCH

Date
SLOPE OF PANEL (TYP)

1203

Revision Schedule
804

9 Sim
1800 ±
A603
2 Sim
A603 STUD FACE TO SIP FACE

Description
INSTALL 38mm x 184mm WOOD FRAMING
MIN. 2 - LOCATIONS AS SHOWN

76
FASTENED BETWEEN TRUSSES (TYP.)
STAIN & VARNISH WOOD SPINDLE
BALUSTRADES @ 100mm O.C. 12
MAX. GUARDRAIL (TYP) 8 19mm x 38mm PERIMETER WOOD
CLOSURE TRIM CONT. (TYP) NOTE: FINAL COORDINATION TO BE
COORDINATED w/ ARCHITECT & SELECTED
WINDOW MANUFACTURER (TYP)

1120
MEZZ. BRIDGE TAPERED BLOCKING ON TOP

1070

MIN.
1203

1203
116 PLATES CONT. TO MATCH
PREFINISHED ALUM. RWL. w/ SLOPE OF PANEL (TYP)

6556
1 Sim
POLY VINYL SPLASH PAD A603 8

No.
(TYP) REFER TO SPEC. A603
STAIN & VARNISH WOOD
15 Sim TRIM CONT. (TYP)
A603 MEZZANINE
STAIN & VARNISH WOOD 2910

260
T.O. CANOPY TRIM CONT. (TYP)
WD. JOISTS
236

236
T.O. WALL PLATE
U/S OF H.S.S. U/S OF H.S.S. 2650

875
516
7 Sim
A603

493
INSTALL 38mm x 184mm WOOD FRAMING
MIN. 2 - LOCATIONS AS SHOWN
FASTENED BETWEEN TRUSSES (TYP.)
4013

NOTE: FINAL COORDINATION TO BE

1203

1203
COORDINATED w/ ARCHITECT & SELECTED

WALL SECTIONS
PREFINISHED VENTED SOFFIT
WINDOW MANUFACTURER (TYP)
CONT. (TYP) REFER TO SPECS.

9 Sim 9
A603
WELCOME CENTRE
A603 2
CREATIVE COMMONS 102
A603
2756

108

1203
CORRIDOR OFFICE
2578

2578
CREATIVE COMMONS 104
108 103

2134
3

1957
A603

WATER FOUNTAIN (TYP)

REFER TO MECH. DWGS.
1203

1203

John R. Park Homestead Heritage Centre

914

10 Sim

754

915 County Road 50, Essex, Ontario N0R 1G0

A603 10
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

A603
112

76
FIRST FLOOR
90

ERCA
Drawn By Checked By
Ai Ai
6/1/2020 8:37:54 AM

Project No
4 WALL SECTION 3 WALL SECTION 2 WALL SECTION 1 WALL SECTION 2020
A502 SCALE: 1 : 20 A201 SCALE: 1 : 20 A201 SCALE: 1 : 20 A201 SCALE: 1 : 20 THIS LINE IS 4" LONG
Sheet No

12 180 Eugenie Street West

400 ± Windsor, ON N8X 2X6
8 519.258.1390
STUD TO SIP
1 Sim
A603
19mm x 38mm PERIMETER WOOD
CLOSURE TRIM CONT. (TYP)

TAPERED BLOCKING ON TOP

PLATES CONT. TO MATCH This drawing is not to be used for
construction unless it is countersigned
SLOPE OF PANEL (TYP) by the Project Architect

784
Issued For (YYMMDD)
TENDER 2020.06.01

F
2 Sim
A603

1270 ±

1203
STUD FACE TO SIP FACE

19mm x 38mm PERIMETER WOOD

CLOSURE TRIM CONT. (TYP)
9 Sim
12 A603
8
TAPERED BLOCKING ON TOP

77
1 Sim PLATES CONT. TO MATCH

Date
A603
SLOPE OF PANEL (TYP)

1491

1203

Revision Schedule
INSTALL 38mm x 184mm WOOD FRAMING
MIN. 2 - LOCATIONS AS SHOWN
2 Sim FASTENED BETWEEN TRUSSES (TYP.)

803
A603 2 Sim

Description
A603

NOTE: FINAL COORDINATION TO BE

COORDINATED w/ ARCHITECT & SELECTED

7340
WINDOW MANUFACTURER (TYP)

1201
6

No.
A603

1515
15
A603 7
5
7 Sim A603
A603
A603

T.O. CANOPY T.O. CANOPY

5486

343
WD. JOISTS WD. JOISTS

236
U/S OF H.S.S.
U/S OF H.S.S.

425

WALL SECTIONS
3995
WELCOME CENTRE
CREATIVE COMMONS 102
108 VESTIBULE
101
2795
2756

2756
2578

2578
2538
2134

2134

2134
PREFINISHED ALUMINUM WINDOW
SYSTEM (TYP.) w/ PERIMETER
CAULKING ON BOTH SIDES CONT.

John R. Park Homestead Heritage Centre

4
14 A603 SEPARATE PRICE NO.1

915 County Road 50, Essex, Ontario N0R 1G0

A603 FOOT GRILLE W/ EDGE TRIM AND DRAIN PAN
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

MATCH TO INTERIOR FLOOR FINISH ELEVATION

REFER TO SPEC (TYP)

FIRST FLOORFIRST FLOOR

ERCA
Drawn By Checked By
2 WALL SECTION 1 WALL SECTION
Ai Ai
6/1/2020 8:37:55 AM

A201 SCALE: 1 : 20 A502 SCALE: 1 : 20

Project No
2020
THIS LINE IS 4" LONG
Sheet No

75
SHEATHING CONT. (TYP) WOOD STRAPPING @ 610mm O.C. 6mil POLY VAPOUR BARRIER (TYP) 180 Eugenie Street West
PLYWOOD CONT. (TYP) REFER TO STRUC. DWGS. Windsor, ON N8X 2X6

75 40
ON 51mm GALV. METAL HORIZ. 'Z'

75 40
519.258.1390
13mm EXT. GRADE PLYWOOD
PREFINISHED (LARGE) 6mil POLY VAPOUR BARRIER ON 13mm & 6mm GIRTS @1220mm O.C. MAX. (TYP) SHEATHING CONT. (TYP)

268 ±
ALUM. GUTTER CONT. (TYP) PREFINISHED METAL EXTERIOR PLYWOOD SHEATHING CONT. (TYP)
PREFINISHED METAL 130

268 ±
REFER TO SPEC. AIR BARRIER CONT. (TYP)
FASCIA CONT. (TYP) FASCIA TUCKED INTO 19mm x 38mm WOOD H.S.S. LINTEL CONT.
19mm x 38mm PERIMETER WOOD PLATE CONT. ACROSS 50mm RIGID INSULATION (TYP)

152
ACROSS OPENING (TYP)

153
WINDOW FRAME (TYP)
PEEL & STICK MEMBRANE ON CLOSURE TRIM CONT. (TYP) LOOKOUTS (TYP) REFER TO STRUC. DWGS.
38mm x 286mm WOOD FASCIA 13mm EXTERIOR GRADE FILL VOID w/ RIGID WEEP VENTS (TYP)
PLYWOOD SHEATHING ON H.S.S. LINTEL (TYP) 12.7mm GYPSUM BOARD HEAD & JAMBS
BOARD CONT. w/ BEVELED ENDS TAPERED BLOCKING ON TOP 75mm SOLID WOOD CANT INSULATION (TYP) PEEL & STICK MEMBRANE AROUND
38mm x 184mm WOOD FRAMING REFER TO STRUC. DWGS.
TO SUIT ROOF SLOPE (TYP) PLATES CONT. TO MATCH STRIP ON 38mm x 89mm ALL OPENINGS CONT. (TYP)
SLOPE OF PANEL (TYP) REFER TO STRUC. DWGS. (TYP) 13mm EXTERIOR GRADE PREFINISHED ALUMINUM WINDOW
WOOD PLATE CONT. (TYP) 113 19mm EXTERIOR PLYWOOD
PLYWOOD SHEATHING ON PREFINISHED METAL BASE SYSTEM (TYP.) w/ PERIMETER
This drawing is not to be used for
PREFINISHED METAL PREFINISHED VENTED SOFFIT SHEATHING CONT. (TYP) construction unless it is countersigned
38mm x 184mm WOOD FLASHING CONT. (TYP) CAULKING ON BOTH SIDES CONT. by the Project Architect
FASCIA CONT. (TYP) CONT. (TYP) REFER TO SPECS.
ALL PREFINISHED WOOD PANELS LOOKOUTS @ 400mm O.C. (TYP) 3 - 38mm x 235mm
PREFINISHED ALUM. RWL. MUST HAVE PERIMETER 'J' MOULDING 7 TYP. CANOPY PARAPET DETAIL WOOD HEADER (TYP) 19mm EXT. GRADE PLYWOOD Issued For (YYMMDD)
BEYOND (TYP) REFER TO BY PANEL SUPPLIER (TYP) SHEATHING CONT. (TYP) TENDER 2020.06.01
SPEC. & ELEVATIONS A601 SCALE: 1 : 10 114 127 25

PREFINISHED VENTED SOFFIT PREFINISHED WOOD VENEER

PANELS ON 13mm EXT. GRADE 8 TYP. WINDOW LARGE MID SECTION DETAIL
CONT. (TYP) REFER TO SPECS.
PLYWOOD SHEATHING ON COMPOSITE HORIZ. WOOD
C A601 SCALE: 1 : 10
15 TYP. EXTERIOR DOOR HEAD DETAIL
COMPOSITE HORIZ. WOOD 38mmx140mm WD. STUDS @ SIDING ON 19mm x 89mm VERT. A601 SCALE: 1 : 10
CLEAR AIR SPACE (TYP)
SIDING ON 19mm x 89mm VERT. 400mm O.C. (TYP) WOOD STRAPPING @ 610mm O.C.
WOOD STRAPPING @ 610mm O.C. ON 65mm GALV. METAL HORIZ. 'Z' 50mm RIGID INSULATION (TYP) PREFINISHED ALUMINUM DOOR
ON 51mm GALV. METAL HORIZ. 'Z' GIRTS @1220mm O.C. MAX. (TYP) SYSTEM (TYP.) w/ PERIMETER
6mil POLY VAPOUR BARRIER (TYP) 12.7mm GYPSUM BOARD
GIRTS @1220mm O.C. MAX. (TYP)
AIR BARRIER CONT. (TYP) ON 38mmx140mm WD. 1 SLOPED POURED 100mm
CAULKING ON BOTH SIDES CONT.
STUDS @ 400mm O.C. (TYP) CONCRETE SILL (TYP.)
AIR BARRIER CONT. (TYP) FILL VOID w/ R20 BATT INSULATION (TYP) 102mm CONCRETE SLAB w/ W.W.M.
PEEL & STICK MEMBRANE CONT.
OVER BASE GIRT (TYP) 6mil POLY VAPOUR BARRIER (TYP) REINFORCING ON COMPACTED
PEEL & STICK MEMBRANE CONT. (TYP)
CLEAR AIR SPACE (TYP) 13mm EXT. GRADE PLYWOOD FIBREGLASS/WOOD WINDOW GRANULAR FILL - REFER TO STRUCTURAL
SHEATHING CONT. (TYP) 19mm EXT. GRADE PLYWOOD SYSTEM w/ PERIMETER 19mm SOLID PINE WOOD SILL, HEAD & JAMB DRAWINGS FOR TYPE & DEPTH (TYP.)
SHEATHING CONT. ON 38mm x 64mm FILL VOID w/ R20 BATT INSULATION (TYP) EXTENSION TO SUIT DEPTH (MATCH GYPSUM FROSTED SLAB CONSTRUCTION: 300
50mm RIGID INSULATION (TYP) CAULKING ON BOTH SIDES (TYP)
WOOD STUDS @ 400mm O.C. (TYP) BOARD FACE) w/ STAIN/VARNISH FINISH ALL 102mm CONC SLAB w/ 152mm x FIRST FLOOR

MIN.
REFER TO SPEC

305
FILL VOID w/ RIGID INSULATION (TYP) FOUR SIDES (TYP) BY DIVISION 06 10 00 152mm - M.W. 13.3 x M.W. 13.3 W.W.M. 0
1 TYP. SOFFIT DETAIL - SLOPED ROOF PREFINISHED METAL BASE PREFINISHED METAL @ MID DEPTH ON 2 - 38mm LAYERS
FLASHING CONT. (TYP) 13mm EXTERIOR GRADE

200
H.S.S. LINTEL CONT. CLADDING CONT. (TYP) OF HD STYROFOAM ON 200mm
A502 SCALE: 1 : 10

Date
ACROSS OPENING (TYP) PLYWOOD SHEATHING (TYP) COMPACTED GRANULAR 'A' FILL (TYP)

76 ±
FILL VOID w/ R20 BATT REFER TO STRUC. DWGS.
INSULATION (TYP) 2 - 38mm x 184mm WOOD PLATES 15M DOWELS @ 300mm O.C. (TYP)
PEEL & STICK MEMBRANE ON REFER TO STRUC. DWGS. 10 mil POLY VAPOUR BARRIER
FASTENED TO VERTICAL 2 - 38mm
12.7mm GYPSUM BOARD BUILT-UP WOOD LINTEL CONT. 75mm SOLID WOOD CANT 19mm x 64mm WOOD FASCIA ON COMP. GRANULAR FILL
STRIP ON 38mm x 89mm x 184mm WOOD POSTS @ EACH 7525 100
ON 38mmx140mm WD. TYP. FLOOR CONSTRUCTION ACROSS OPENING (TYP) BOARD CONT. FASTEN THRU REFER TO STRUC. DWGS (TYP)

410
WOOD PLATE CONT. (TYP) END w/ 3 - SCREWS (TYP) TYP. FOUNDATION WALL CONST.
STUDS @ 400mm O.C. (TYP) 19mm T&G SUBFLOOR SHEATHING REFER TO STRUC. DWGS. TO STUDS (TYP)
ON PRE-ENGINEERED WOOD JOISTS REINF. POURED CONCRETE WALL w/ 38mm
w/ 12.7mm GYPSUM BOARD 6mil POLY VAPOUR BARRIER (TYP) PERIMETER RIGID INSULATION TO TOP OF FILL VOID w/ HIGH DENSITY
13mm EXTERIOR GRADE

Revision Schedule
FOOTING (REFER TO STRUCTURAL RIGID INSULATION (TYP.)
PLYWOOD SHEATHING (TYP) FILL VOID WITH RIGID
MEZZANINE TYP. CANOPY ROOF CONSTRUCTION DRAWINGS FOR REINFORCEMENT TYPE.)
INSULATION (TYP)
2910 SINGLE PLY ROOF MEMBRANE ON 38mm RIGID INSULATION (TYP.)
13mm FIBERBOARD ON 25mm PREFINISHED ALUMINUM DOOR 136 64

Description
COMPOSITE HORIZ. WOOD POLYISOCYANURATE INSULATION SYSTEM (TYP.) w/ PERIMETER
SIDING ON 19mm x 89mm VERT. CAULKING CONT. (TYP) CAULKING ON BOTH SIDES CONT. 200
ON VAPOUR RETARDER ON 19mm
WOOD STRAPPING @ 610mm O.C. EXTERIOR GRADE T&G PLYWOOD PREFINSHED SOFFIT w/ 9 TYP. WINDOW SMALL MID SECTION DETAIL 14 TYP. EXTERIOR DOOR SILL DETAIL
ON 51mm GALV. METAL HORIZ. 'Z' SHEATHING ON 38mm x 184mm ROOF PERIMETER TRIM CONT. (TYP) A602 SCALE: 1 : 10
GIRTS @1220mm O.C. MAX. (TYP) JOIST @ 300mm O.C. w/ VENTED REFER TO SPEC. A401 SCALE: 1 : 10
PREFINISHED METAL SOFFIT(TYP)
AIR BARRIER CONT. (TYP)
SUSPENDED ACOUSTIC 6 TYP. CANOPY WALL TRANSITION DETAIL 1
TILE CEILING SYSTEM (TYP)
CLEAR AIR SPACE (TYP) A501 SCALE: 1 : 10
1 NOTE: RUBBER BASE ON 13mm
PREFINISHED METAL COPING
TYP. CANOPY ROOF CONSTRUCTION
EXTERIOR GRADE PLYWOOD SINGLE PLY ROOF MEMBRANE ON
50mm RIGID INSULATION (TYP) FIBREGLASS/WOOD WINDOW 200 BACKER CONT. BELOW WOOD OVER CANT STRIP CONT. (TYP) 13mm FIBERBOARD ON 25mm
TYP. CANOPY ROOF CONSTRUCTION SYSTEM w/ PERIMETER PANELS ONLY (TYP) POLYISOCYANURATE INSULATION ON
ACT-1 B

No.
13mm EXT. GRADE PLYWOOD SINGLE PLY ROOF MEMBRANE ON CAULKING ON BOTH SIDES (TYP) CARRY ROOF MEMBRANE VAPOUR RETARDER ON 19mm
SHEATHING CONT. (TYP) 2450 13mm FIBERBOARD ON 25mm OVER CANT FACE CONT. (TYP)
W1 REFER TO SPEC 19mm SOLID PINE WOOD SILL, HEAD & JAMB EXTERIOR GRADE T&G PLYWOOD
38mm x 38mm WOOD FURRING POLYISOCYANURATE INSULATION SHEATHING ON 38mm x 184mm ROOF
EXTENSION TO SUIT DEPTH (MATCH GYPSUM
CONT. ACROSS OPENING (TYP) 6mil POLY VAPOUR BARRIER (TYP) ON VAPOUR RETARDER ON 19mm 2 - 38mmx184mm WD. BOTTOM PEEL & STICK MEMBRANE JOIST @ 300mm O.C. (TYP)
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
EXTERIOR GRADE T&G PLYWOOD PLATE ON GASKET CONT. (TYP) ON 13mm EXTERIOR
FILL VOID w/ R20 BATT INSULATION (TYP) FOUR SIDES (TYP) BY DIVISION 06 10 00
PEEL & STICK MEMBRANE AROUND SHEATHING ON 38mm x 184mm ROOF GRADE PLYWOOD
ALL OPENINGS CONT. (TYP) 75mm SOLID WOOD CANT
FILL VOID w/ BATT INSULATION (TYP) JOIST @ 300mm O.C. w/ VENTED RUBBER BASE CONT. (TYP) SHEATHING CONT. (TYP)
PEEL & STICK MEMBRANE ON STRIP ON 38mm x 89mm
PREFINISHED METAL SOFFIT (TYP)
BOX LINTEL CONT. 19mm x 64mm WOOD FASCIA WOOD PLATE CONT. (TYP)
WEEP VENTS (TYP) 6mil POLY VAPOUR 102mm CONCRETE SLAB w/ W.W.M.
ACROSS OPENING (TYP) BOARD CONT. FASTEN THRU REINFORCING ON COMPACTED
BARRIER CONT. (TYP)
13

REFER TO STRUC. DWGS. TO STUDS (TYP)

WALL SECTION DETAILS

GRANULAR FILL - REFER TO STRUCTURAL FILL VOID w/ BATT INSULATION (TYP)

102
PREFINISHED METAL BASE AIR BARRIER CONT.TIED INTO PREFINISHED METAL
FLASHING CONT. (TYP) FIRST FLOOR DRAWINGS FOR TYPE & DEPTH (TYP.)
PROVIDE PERIMETER SHADOW WINDOW FRAME CONT. (TYP) FASCIA CONT. (TYP)
BEAD TO FINISH GYPSUM 0

MIN.
203
FIBREGLASS/WOOD WINDOW 6mil POLY VAPOUR BARRIER (TYP)
7 Sim
BOARD TO 13mm FROM WOOD PREFINISHED BENT METAL BASE
SYSTEM w/ PERIMETER PREFINSHED SOFFIT w/ 6mil POLY VAPOUR BARRIER 13mm EXTERIOR GRADE
A201 (TYP) REFER TO SPEC FLASHING CONT. ON PEEL &
CAULKING ON BOTH SIDES (TYP) PERIMETER TRIM CONT. (TYP) LAP & TIED INTO WINDOW PLYWOOD SHEATHING ON 12.7mm GYPSUM BOARD (TYP)
STICK MEMBRANE ON 2 - 38mm x 10 mil POLY VAPOUR BARRIER
REFER TO SPEC 19mm SOLID PINE WOOD SILL, HEAD & JAMB REFER TO SPEC. FRAME CONT. (TYP) 38mm x 184mm WOOD FRAMING
38mm WD. FURRING (TYP) ON COMP. GRANULAR FILL
EXTENSION TO SUIT DEPTH (MATCH GYPSUM REFER TO STRUC. DWGS. (TYP) 13mm EXTERIOR GRADE
BOARD FACE) w/ STAIN/VARNISH FINISH ALL REFER TO STRUC. DWGS (TYP) PLYWOOD SHEATHING (TYP)
PREFINISHED ALUMINUM DOOR 13mm EXT. GRADE PLYWOOD TYP. FOUNDATION WALL CONST.
FOUR SIDES (TYP) BY DIVISION 06 10 00 REINF. POURED CONCRETE WALL w/ 38mm 13mm PREMOULDED PREFINISHED VENTED SOFFIT
SYSTEM (TYP.) w/ PERIMETER ON WOOD LINTEL CONT. PREFINISHED ALUMINUM WINDOW
PERIMETER RIGID INSULATION TO TOP OF EXPANSION JOINT CONT. (TYP) CONT. (TYP) REFER TO SPECS.
2 TYP. WINDOW HEAD DETAIL CAULKING ON BOTH SIDES CONT. ACROSS OPENING (TYP) SYSTEM (TYP.) w/ PERIMETER
REFER TO STRUC. DWGS. FOOTING (REFER TO STRUCTURAL CAULKING ON BOTH SIDES CONT.
A601 SCALE: 1 : 10 DRAWINGS FOR REINFORCEMENT TYPE.) 38mm RIGID INSULATION (TYP.)
138 62

200 112 151 127

FIBREGLASS/WOOD WINDOW 10 TYP. WALL BASE DETAIL @ WINDOW

SYSTEM w/ PERIMETER 13 TYP. WINDOW HEAD DETAIL - ALUM.
CAULKING ON BOTH SIDES (TYP) 19mm SOLID PINE WOOD SILL, HEAD & JAMB A601 SCALE: 1 : 10
REFER TO SPEC EXTENSION TO SUIT DEPTH (MATCH GYPSUM A501 SCALE: 1 : 10
BOARD FACE) w/ STAIN/VARNISH FINISH ALL
38mm x 38mm WOOD FURRING FOUR SIDES (TYP) BY DIVISION 06 10 00 5 TYP. DOOR HEAD DETAIL - ALUMINUM
CONT. ACROSS OPENING (TYP) 7 Sim
A602

John R. Park Homestead Heritage Centre

SCALE: 1 : 10
PEEL & STICK MEMBRANE AROUND
A201 PROVIDE PERIMETER SHADOW
BEAD TO FINISH GYPSUM
H PREFINISHED ALUMINUM DOOR 1 WINDOW FRAME w/ SILL GASKET &

915 County Road 50, Essex, Ontario N0R 1G0

ALL OPENINGS CONT. (TYP) BOARD TO 13mm FROM WOOD SYSTEM (TYP.) w/ PERIMETER PERIMETER CAULKING CONT. (TYP)
100
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

(TYP) REFER TO SPEC CAULKING ON BOTH SIDES CONT.

COMPOSITE HORIZ. WOOD APPLY DAMPROOFING TO
SIDING ON 19mm x 89mm VERT. COLUMN BASE PRIOR TO 152mm CONCRETE SLAB w/ W.W.M.
13

WOOD STRAPPING @ 610mm O.C. 2- 38mmx140mm WD. SILL PLATES

CONT. ACROSS OPENING (TYP)
PREFINISHED ALUMINUM DOOR
SYSTEM (TYP.) w/ PERIMETER B EXTRUDED ALUM. SILL ON
A FULL BED OF MASTIC POURING SLAB (TYP)
H.S.S. COLUMN (TYP)
GALVANIZED METAL ANGLE
25mm x 75mm x 12ga. LLV (TYP.)
REINFORCING ON COMPACTED
GRANULAR FILL - REFER TO STRUCTURAL
ON 51mm GALV. METAL HORIZ. 'Z' CAULKING ON BOTH SIDES CONT. 100 w/ CAULKING CONT. (TYP.)
GIRTS @1220mm O.C. MAX. (TYP) 12.7mm GYPSUM BOARD REFER TO STRUC. DWGS. EMBEDDED IN CONC. TYP. DRAWINGS FOR TYPE & DEPTH (TYP.)
ON 38mmx140mm WD. 152mm CONCRETE SLAB w/ W.W.M. 102mm CONCRETE SLAB w/ W.W.M.
REINFORCING ON COMPACTED 13mm PREMOULD PERIMETER SLOPED POURED 102mm FOOT GRILLE W/ EDGE TRIM AND
STUDS @ 400mm O.C. (TYP) REINFORCING ON COMPACTED
GRANULAR FILL - REFER TO STRUCTURAL EXPANSION JOINT (TYP) CONCRETE SILL (TYP.) DRAIN PAN MATCH TO INTERIOR
AIR BARRIER CONT. (TYP) GRANULAR FILL - REFER TO STRUCTURAL
DRAWINGS FOR TYPE & DEPTH (TYP) FLOOR FINISH ELEVATION
6mil POLY VAPOUR BARRIER (TYP) DRAWINGS FOR TYPE & DEPTH (TYP.)
SLOPED POURED 102mm
FIRST FLOOR PREFINISHED METAL BASE FIRST FLOOR
CONCRETE SILL (TYP.)
754

CLEAR AIR SPACE (TYP) FILL VOID w/ R20 BATT INSULATION (TYP) FOOT GRILLE W/ EDGE TRIM AND FLASHING ON PEEL & STICK
0 0

50
300 DRAIN PAN MATCH TO INTERIOR MEMBRANE CONT. (TYP)
50mm RIGID INSULATION (TYP) 38mmx140mm WD. BOTTOM PEEL & STICK MEMBRANE CONT. (TYP)
FLOOR FINISH ELEVATION

200
203
PLATE ON GASKET CONT. (TYP)

102
200
13mm EXT. GRADE PLYWOOD RUBBER BASE CONT. (TYP) FIRST FLOOR
FROSTED SLAB CONSTRUCTION: FIN. GRADE
SHEATHING CONT. (TYP) 0
50

102mm CONC SLAB w/ 152mm x 152mm - M.W.

PEEL & STICK MEMBRANE ON 102mm CONCRETE SLAB w/ W.W.M. 10 mil POLY VAPOUR BARRIER
13.3 x M.W. 13.3 W.W.M. @ MID DEPTH ON 2 -
200

102

PREFINISHED BENT METAL BASE REINFORCING ON COMPACTED 75 25 100 ON COMP. GRANULAR FILL
38mm LAYERS OF HD STYROFOAM ON 200mm
FLASHING CONT. (TYP) GRANULAR FILL - REFER TO STRUCTURAL REFER TO STRUC. DWGS (TYP)
COMPACTED GRANULAR 'A' FILL (TYP)
FIRST FLOOR DRAWINGS FOR TYPE & DEPTH (TYP.)
15M DOWELS @ 300mm O.C. (TYP)
0 10 mil POLY VAPOUR BARRIER
REFER TO STRUC. DWGS. 25 100 TYP. FOUNDATION WALL CONST.
NOTE: RUBBER BASE ON 13mm
410

13mm PREMOULDED ON COMP. GRANULAR FILL

ERCA
POURED CONCRETE PIER (TYP) REINF. POURED CONCRETE WALL w/ 38mm FILL VOID w/ HIGH DENSITY
EXPANSION JOINT CONT. (TYP) EXTERIOR GRADE PLYWOOD REFER TO STRUC. DWGS (TYP) REFER TO STRUC. DWGS. PERIMETER RIGID INSULATION TO TOP OF RIGID INSULATION (TYP.)
BACKER CONT. BELOW WOOD TYP. FOUNDATION WALL CONST.
REINF. POURED CONCRETE WALL w/ 38mm FOOTING (REFER TO STRUCTURAL
PANELS ONLY (TYP)
TYP. FOUNDATION WALL CONST. PERIMETER RIGID INSULATION TO TOP OF DRAWINGS FOR REINFORCEMENT TYPE.) 38mm RIGID INSULATION (TYP.)
FILL VOID w/ HIGH DENSITY
REINF. POURED CONCRETE WALL w/ 38mm FOOTING (REFER TO STRUCTURAL RIGID INSULATION (TYP.)
10 mil POLY VAPOUR BARRIER 200
PERIMETER RIGID INSULATION TO TOP OF DRAWINGS FOR REINFORCEMENT TYPE.) Drawn By Checked By
ON COMP. GRANULAR FILL
FOOTING (REFER TO STRUCTURAL 38mm RIGID INSULATION (TYP.)
REFER TO STRUC. DWGS (TYP)
11 TYP. EXTERIOR COLUMN BASE DETAIL 12 TYP. WALL BASE DETAIL - ALUM. Ai Ai
6/1/2020 8:38:00 AM

DRAWINGS FOR REINFORCEMENT TYPE.)

38mm RIGID INSULATION (TYP.) Project No
200 A201 SCALE: 1 : 10 A501 SCALE: 1 : 10
3 TYP. WINDOW SILL DETAIL 2020
A601 SCALE: 1 : 10 4 TYP. DOOR SILL DETAIL - ALUMINUM THIS LINE IS 4" LONG
Sheet No
A602 SCALE: 1 : 10
THE INFORMATION INCLUDED IN THIS ELECTRONIC DRAWING FILE IS PROTECTED BY COPYRIGHT. UNAUTHORIZED USE OF THIS FILE WITHOUT THE WRITTEN PERMISSION OF ARCHITECTTURA INC. ARCHITECTS IS PROHIBITED.
ARCHITECTTURA INC. ARCHITECTS IS RESPONSIBLE ONLY FOR INFORMATION SHOWN ON A MECHANICAL REPRODUCTION OF THIS DRAWING FILE THAT HAS BEEN SIGNED AND SEALED BY A REGISTERED ARCHITECT EMPLOYED BY THE FIRM.
THIS DRAWING SHEET IS 36"X24" IN SIZE. IT IS RECOMMENDED THAT ANY REPRODUCTION, ELECTRONIC OR OTHERWISE, BE TO THE SAME SHEET SIZE
TO ENSURE THE ACCURACY OF DRAWING SCALES DEPICTED ON THIS SHEET. THIS DRAWING IS NOT TO BE SCALED - USE FIGURED DIMENSIONS ONLY.
A603
LEGEND

FM FIXED MIRROR
TM TILTED MIRROR
FM & TM
HD HAND DRYER
2' - 6" PTD PAPER TOWEL DISPENSER
SD SOAP DISPENSER
PROVIDE MIN. ONE SND SANITARY NAPKIN DISPOSAL
TILTED MIRROR IN ALL PTD CH COAT HOOK
BARRIER FREE CH
BCH BARRIER FREE COAT HOOK
WASHROOMS (TYP.) SSS STAINLESS STEEL SHELF
HD TP TOILET PAPER DISPENSER
SD GB1 762 x 762mm GRAB BAR
370 1 1/2" DIA. GRAB 610 BCH GB2 610mm GRAB BAR
485mm FAUCET - REFER BARS (TYP) UNIVERSAL WASHROOM - GENERAL NOTES
GB3 FOLD DOWN GRAB BAR 180 Eugenie Street West

760
TO SPECS. SSS Windsor, ON N8X 2X6
150 EQ EQ BDF BARRIER FREE DRINKING FOUNTAIN 519.258.1390
INSULATE ALL EXPOSED DF DRINKING FOUNTAIN 1. PROVIDE AUTOMATIC DOOR OPERATORS (ADO) AND DOOR ACTUATORS (DA) WHERE
PIPING AT LAVATORIES ADO AUTOMATIC DOOR OPERATOR WALL SWITCH INDICATED ON PLAN.
(TYP.) TOILET TISSUE PTL PUSH TO LOCK DOOR BUTTON
DISPENSER 2. PROVIDE PUSH TO LOCK BUTTON (LB) WHERE INDICATED IN PLAN.

1500
U.N.O. UNLESS NOTED OTHERWISE

1200 U.N.O.

1200 U.N.O.
SND FDS FOLD DOWN SHOWER SEAT

NOTED OTHERWISE

1030 U.N.O.
3. REFER TO HARDWARE SCHEDULE FOR COMPLETE LIST OF REQUIRED DOOR HARDWARE

1200

1000 U.N.O.
ES EMERGENCY SIGN

840 MAX. UNLESS

210

1100
EPB EMERGENCY PUSH BUTTON ITEMS.

1000

901
AVS AUDIBLE VISUAL SIGNAL
735mm
690 MIN.

4. PROVIDE AN EMERGENCY CALL BUTTON (EB) WITH AN EMERGENCY SIGN THAT CONTAINS

750
685mm
770

430 FCT FOLDING CHANGE TABLE

CL THE WORDS "IN THE EVENT OF AN EMERGENCY PUSH EMERGENCY BUTTON AND AN

1' - 7" MAX

600
This drawing is not to be used for

430 MIN.
610
457 230 construction unless it is countersigned
280 * REFER TO SPECIFICATIONS FOR PRODUCT SPECIFIC AUDIBLE AND VISUAL SIGNAL WILL ACTIVATE" IN LETTERS AT LEAST 1" (25mm) HIGH AND 1/4" by the Project Architect
INFORMATION (6mm) STROKE. POST ABOVE THE EMERGENCY BUTTON - REFER TO ELECTRICAL DRAWINGS.
MIN.
230

430-460
FIN. FLOOR FIN. FLR. FINISHED FLOOR Issued For (YYMMDD)
TENDER 2020.06.01
SIDE ELEVATION FRONT ELEVATION

TYPICAL BARRIER FREE SINK DIMENSIONS TYPICAL BARRIER FREE TOILET DIMENSIONS TYPICAL WASHROOM FIXTURE MOUNTING HEIGHTS
SCALE: 1 : 20 SCALE: 1 : 20 SCALE: 1 : 20

E UNIVERSAL WR
105

ø1700mm TURNING CIRCLE

HD 810mm x 1830mm CLEAR SPACE FOR AN

ADULT SIZED CHANGE TABLE

Date
0
70 A A701
ø1 760mm x 1500mm CLEAR FLOOR AREA
TM B
PTD 900mm x 1500mm TRANSFER SPACE
PTL

SD
8 ADO ADO
920mm x 1370mm LAVATORY APPROACH SPACE

PTD
ES

SND
TP

Revision Schedule
EB AVS
3 - 38mm x 160mm BUILT UP WOOD POST

Description
TP
@ FOLDING BARS LOCATIONS (TYP)
ADO PTL
SND

900

900
B C
1 ENLARGED UNIVERSAL WASHROOM PLAN
A201 SCALE: 1 : 50

No.
SOUND ATTENUATION
3 BLANKET (TYP)

B UNIVERSAL WC ELEV B A UNIVERSAL WC ELEV A

4 F2b

A202 SCALE: 1 : 24 A202 SCALE: 1 : 24

ø
15

1600
00 ø1500mm TURNING CIRCLE

WASHROOM PLANS &

920mm x 1370mm LAVATORY
925 925 925 2244 APPROACH SPACE
5 FCT
PROVIDE SOLID WOOD BLOCKING

PTD

1555
FOR ALL PLUMBING FIXTURES

ELEVATIONS
WOMEN W/R F2b HD HD ACCESSORIES & PARTITIONS (TYP)
460
113
1100 F2b

P2c
F2b

1100
P2c
F2c F2b
6

1712
2650 1100 1269
COMMON HALLWAY
TM 112

John R. Park Homestead Heritage Centre

HD,
1100 F2c

915 County Road 50, Essex, Ontario N0R 1G0

SEE ELEC. F2b
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

P2c

1100
P2c
1100

360
460
7 HD HD
F2b
E
MEN W/R

1555

PTD
111
A701 F2b
460
F2b
D

2244 925 1850 920mm x 1370mm LAVATORY

APPROACH SPACE
ø1500mm TURNING CIRCLE
ø

1600
15 SOUND ATTENUATION
00
BLANKET (TYP)

F2b
8

ERCA
P2c
.

Drawn By Checked By

E TYPICAL WC ELEVATION E D TYPICAL WC ELEVATION D Ai Ai

6/1/2020 8:38:05 AM

A202 SCALE: 1 : 24 A202 SCALE: 1 : 24 2 ENLARGED WASHROOM PLAN Project No

A201 SCALE: 1 : 50 2020

THIS LINE IS 4" LONG
Sheet No

SOLID WOOD HANDRAIL G G

STAINED & VARNISH (TYP)
180 Eugenie Street West
6 6 Windsor, ON N8X 2X6
519.258.1390

EXTEND HANDRAIL 300mm FROM

1 - TREAD DEPTH PAST THE LAST STAIR NO.1
STAIR NO.1 TREAD & WRAP CORNER 114

1032
114 UP UP
2 2
This drawing is not to be used for
A901 A901 construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

TENDER 2020.06.01

OFFICE MEZZ. (OPEN)

104 115

1140

1 FIRST FLOOR PLAN - STAIR NO. 1 4 MEZZANINE PLAN - STAIR NO. 1

A201 SCALE: 1 : 25 A201 SCALE: 1 : 25

286

Date
26 NOSING 260
12.7mm PLYWOOD
RISER

5mm RUBBER TREAD & RISER (TYP)

ø38mm SOLID WOOD HANDRAIL

171
STAINED & VARNISH (TYP) 38mm x 380mm

Revision Schedule
WOOD TREAD

Description
38
ø13mm ROD SUPPORTS @
1200mm o.c. MAX. (TYP)

3 COUNTER-SUNK SCREWS
38mm x 380mm
PER METAL MOUNTING PLATE
WOOD STRINGERS
2 - 38mm x 150mm WOOD
BLOCKING BLOCKING
BETWEEN STUDS (TYP)

No.
6 TYP. HANDRAIL DETAIL 5 TYP. STAIR TREAD DETAIL
A901 SCALE: 1 : 5 A901 SCALE: 1 : 10

STAIR PLAN, SECTION, AND

EXTEND HANDRAIL 300mm FROM 1 - MEZZ. (OPEN)
TREAD DEPTH PAST THE LAST TREAD 115
BUILT-UP GUARD BEYOND

MEZZ. (OPEN)

HALF WALL (BEYOND)

115
F GH
1120

1120
1140 4160 P2c
1 Sim
16 TREADS @ 260mm ea. A603

MEZZANINE MEZZANINE

DETAILS
2910 2910
6
A901

SOLID WOOD HANDRAIL

STAINED & VARNISH (TYP)
1/2" GYPSUM @ UNDERSIDE OF
STAIRS STAIR NO.1
114
5

John R. Park Homestead Heritage Centre

A901 P2c
17 RISERS @ 171mm ea.

OFFICE

915 County Road 50, Essex, Ontario N0R 1G0

104 WELCOME CENTRE
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

102
2910

OFFICE
104
EXTEND HANDRAIL 300mm FROM
1 - TREAD DEPTH PAST THE LAST
TREAD & WRAP CORNER

PLATFORM SEATING (TYP)

REFER TO MILLWORK DWG. A1201
HANDRAIL

P2c
920

FIRST FLOOR FIRST FLOOR

0 0

ERCA
Drawn By Checked By
2 STAIR NO. 1 - SECTION 3 STAIR NO. 1 - CROSS SECTION
Ai Ai
6/1/2020 8:38:08 AM

A502 SCALE: 1 : 25 A901 SCALE: 1 : 25

Project No
2020
THIS LINE IS 4" LONG
Sheet No

538
44
. ACT-1 F2b 231
2450

875
7
A1201
1 Sim 38 mm x 89 mm WOOD BLOCKING

174
SERVERY A301

875
3 109
BUILT-UP WOOD LINTEL (TYP) 180 Eugenie Street West
REFER TO STRUC. DWGS. WELCOME CENTRE
Windsor, ON N8X 2X6
19mm MELAMINE PANEL DOOR,

3700
200
WOMEN W/R 102 519.258.1390
2 A1201 GABLES, BOTTOM, TOP w/ P.V.C.
LED RECESSED PUCK LIGHTING 113
6 19mm MELAMINE PANEL DOOR, ON ALL EXPOSED EDGES SIM
GABLES, BOTTOM, TOP w/ P.V.C. (TYP) REFER TO ELEC. DWGS.

875
A1201
ON ALL EXPOSED EDGES 10
A1201
SHELF SUPPORTS - REFER TO

610
SPEC VINYL TACKBOARD MOUNTED

875
TO REAR OF GLASS DISPLAY

762
SHELF SUPPORTS - REFER TO 12.7mm MELAMINE PANEL MIRROR, SEE SPECS & TYPICAL
SPEC BACK - TYP. 230 This drawing is not to be used for
1 MWP - SERVERY PLAN - 109 MOUNTING HEIGHT DETAIL
construction unless it is countersigned
by the Project Architect

695
A201 SCALE: 1 : 50 WOOD BLOCKING - TYP. 170
7 12.7mm MELAMINE PANEL Issued For (YYMMDD)
A1201 BACK - TYP.
CREATIVE COMMONS TENDER 2020.06.01
ADJUST
WOOD BLOCKING - TYP. 108
305 19 12 A1201
COMMON HALLWAY
112

305 19 F2b 13 mm TEMPERED GLASS 44

1349

724
629 19 610 SHELF BY THIS DIVISION (TYP)

610
43

458
6mm TEMPERED SLIDING
610 19

875
19mm POST FORMED PLASTIC 19mm POST FORMED PLASTIC GLASS BY THIS DIVISION (TYP)
SINK & FAUCET AS PER MECH.

2134

2134
LAMINATE P.LAM COUNTER TOP & LAMINATE P.LAM COUNTER TOP & ADJUST
BACK/SIDE SPLASH w/ 180° WRAP BACK/SIDE SPLASH w/ 180° WRAP

200
EDGES - TYP. 19mm POST FORMED PLASTIC
EDGES - TYP. PROVIDE CUT OUT FOR LIGHT SWITCH AS

1959
LAMINATE P.LAM COUNTER TOP & 231 CREATIVE COMMONS
BACK/SIDE SPLASH w/ 180° WRAP REQUIRED REFER TO ELEC. DWGS. (TYP)
108

875
EDGES - TYP.
MEN W/R
MWE - SERVERY EAST ELEVATION

3700
2

38
111
SINK 3/4" MELAMINE PANEL w/
A1201 SCALE: 1 : 50 12.7mm MELAMINE PANEL BACK 19 mm BACK PANEL 10
12.7mm MELAMINE PANEL BACK P.LAM ON ALL EXPOSED

152
A1201

Date
& DRAWER CONSTRUCTION

875
EDGES
8 19 mm x 140mm WOOD SUPPORT
A1201 19mm MELAMINE PANEL DOOR, FALSE
19mm MELAMINE PANEL DOOR, DRAWER FRONT, BOTTOM & GABLES & WOOD BLOCKING - TYP.

875
DRAWER FRONT, BOTTOM, GABLES & w/ P.V.C. ON ALL EXPOSED EDGES
SHELF w/ P.V.C. ON ALL EXPOSED 3/4" MELAMINE GUSSET 38 mm x 89 mm WOOD BLOCKING
EDGES (2) C/W P.LAM ON ALL

849
812

812

Revision Schedule
EXPOSED EDGES
SOLID WD BLOCKING AS
SHELF SUPPORTS -
REQUIRED

610

Description
REFER TO SPEC.
WOOD BLOCKING - TYP. WOOD BLOCKING - TYP.
13 MWP - TYP. DISPLAY CASE PLAN
A201 SCALE: 1 : 50
19mm FIR PLYWD. BASE FRONT, 19mm FIR PLYWD. BASE FRONT,

102

102
BACK & SIDES - TYP. BACK & SIDES - TYP.

7 MWS - TYP. UPPER & LOWER CABINET 8 MWS - TYP. BASE CABINET w/ SINK SECTION 17 MWS - TYP. WASHROOM VANITY
3 MWE - SERVERY SOUTH ELEVATION 10 MWS - TYP. DISPLAY CASE SECTION
A502 SCALE: 1 : 10 A1201

No.
SCALE: 1 : 10 SCALE: 1 : 10
A1201 SCALE: 1 : 50 A1201 SCALE: 1 : 10

9
38mm x 89mm WOOD A1201
5755 TYP. FLOOR CONSTRUCTION STUDS @ 400mm O.C. WELCOME CENTRE
CARPET FINISH ON 19mm 19mm T&G SUBFLOOR SHEATHING 9 SPACE FROM EXTERIOR 102
EXTERIOR GRADE PLYWOOD ON PRE-ENGINEERED WOOD JOISTS WALL AS REQUIRED (TYP)
SHEATHING ON 38mm x 184mm 5 w/ 12.7mm GYPSUM BOARD
WOOD FLOOR JOISTS @ 400mm A1201 13mm PLYWOOD
O.C. (TYP) REFER TO SPEC. MECH. ROOM BACKER (TYP)
P2c
117
MEZZANINE 13mm FINISHED PLYWOOD A1201 11
750

STAINED & VARNISHED (TYP) 9

2910
A1201

594
SUSPENDED ACOUSTIC T.O. WALL PLATE ELECTRIC FIREPLACE
2008

TILE CEILING SYSTEM (TYP) INSERT (TYP)

750

2650

560
WELCOME CENTRE
13mm FINISHED PLYWOOD
102

2650
STAINED & VARNISHED (TYP)

560
508

MILLWORK
A1201
ACT-1
2450 ELECTRIC

676
16 MWP - TYP. FIREPLACE HEAD DETAIL FIREPLACE
ROLLING SHUTTER DOOR
(TYP) REFER TO SPECS. A1201 SCALE: 1 : 10

260
12.7mm GYPSUM BOARD (TYP)
ELECTRIC FIREPLACE 1150 1150 1150 404
1201

INSERT (TYP)
4 MWP - TYP. PLATFORM SEATING PLAN
38mm x 89mm PERIMETER
A201 SCALE: 1 : 50 P. LAM COUNTER (TYP) 410 WOOD FRAME (TYP) 11 MWE - TYP. FIREPLACE ELEVATION 14 MWP - TYP. FIREPLACE PLAN
REFER TO MILLWORK PLAN

John R. Park Homestead Heritage Centre

A1201 SCALE: 1 : 50 A201 SCALE: 1 : 50
SERVERY CREATIVE COMMONS
13mm FINISHED PLYWOOD
2200

109 108

915 County Road 50, Essex, Ontario N0R 1G0

STAINED & VARNISHED (TYP)
BIM 360://2020 JRPH Heritage Centre/2020 ARCH-360-OPT1.rvt

38mm x 140mm PERIMETER

WOOD FRAMING (TYP)
WELCOME CENTRE P2c STAIR NO.1
102 114
RUBBER BASE CONT. (TYP)
P2c 15 MWP - TYP. FIREPLACE JAMB
999

CARPET FINISH ON 19mm A1201 SCALE: 1 : 10

102mm CONCRETE SLAB w/ W.W.M.
EXTERIOR GRADE PLYWOOD SIDING TYPE S-2
REINFORCING ON COMPACTED 16
SHEATHING ON 38mm x 184mm A1201
GRANULAR FILL - REFER TO STRUCTURAL 38mm x 89mm WOOD
WOOD FLOOR JOISTS @ 400mm
203

DRAWINGS FOR TYPE & DEPTH (TYP.) STUDS @ 400mm O.C.

O.C. (TYP) REFER TO SPEC.
SPACE FROM EXTERIOR
FIRST FLOOR WALL AS REQUIRED (TYP)

150
750 750 508 SOLID WOOD BATTEN-CEDAR
609

203

466
13mm FINISHED PLYWOOD
10 mil POLY VAPOUR BARRIER STAINED & VARNISHED (TYP) SIDING TYPE S-1
203

ON COMP. GRANULAR FILL

13mm PLYWOOD
REFER TO STRUC. DWGS (TYP)
BACKER (TYP)
PROVIDE RECESSED LED
676

PUCK LIGHTING FOR EACH

2184
TYP. FOUNDATION WALL CONST. DISPLAY CABINET (TYP)
REINF. POURED CONCRETE WALL REFER TO ELEC. DWGS.

(REFER TO STRUCTURAL DRAWINGS 375 695

ERCA
ELECTRIC FIREPLACE
FOR REINFORCEMENT TYPE.)
INSERT (TYP)
100mm CONCRETE SLAB w/ W.W.M. SEPARATE PRICE NO.3 & NO.4
260

10 mil POLY VAPOUR BARRIER REINFORCING ON COMPACTED RUBBER BASE CONT. (TYP) DELETE CANEXEL SIDING & REPLACE w/
ON COMP. GRANULAR FILL GRANULAR FILL - REFER TO STRUCTURAL SAGIPER NORTH AMERICA SIDING (TYP)
REFER TO STRUC. DWGS (TYP) DRAWINGS FOR TYPE & DEPTH (TYP.) REFER TO SPEC. Drawn By Checked By
NOTE: RUBBER BASE ON 13mm TACKBOARD ON BACK PANEL
EXTERIOR GRADE PLYWOOD 10 OF EACH DISPLAY CASE (TYP) Ai Ai
6/1/2020 8:38:13 AM

BACKER CONT. BELOW WOOD A1201

Project No
PANELS ONLY (TYP)
5 MWS - TYP. PLATFORM SEATING SECTION 6 WALL SECTION 12 MWE - TYP. DISPLAY CASE ELEVATION 2020
A1201 SCALE: 1 : 20 A201 SCALE: 1 : 20
MWS - TYP. FIREPLACE SECTION A1201 SCALE: 1 : 50
9 THIS LINE IS 4" LONG
Sheet No
A1201 SCALE: 1 : 20
THE INFORMATION INCLUDED IN THIS ELECTRONIC DRAWING FILE IS PROTECTED BY COPYRIGHT. UNAUTHORIZED USE OF THIS FILE WITHOUT THE WRITTEN PERMISSION OF ARCHITECTTURA INC. ARCHITECTS IS PROHIBITED.
ARCHITECTTURA INC. ARCHITECTS IS RESPONSIBLE ONLY FOR INFORMATION SHOWN ON A MECHANICAL REPRODUCTION OF THIS DRAWING FILE THAT HAS BEEN SIGNED AND SEALED BY A REGISTERED ARCHITECT EMPLOYED BY THE FIRM.
THIS DRAWING SHEET IS 36"X24" IN SIZE. IT IS RECOMMENDED THAT ANY REPRODUCTION, ELECTRONIC OR OTHERWISE, BE TO THE SAME SHEET SIZE
TO ENSURE THE ACCURACY OF DRAWING SCALES DEPICTED ON THIS SHEET. THIS DRAWING IS NOT TO BE SCALED - USE FIGURED DIMENSIONS ONLY.
A1201
FOUNDATION NOTES
FOUNDATION WALL TYPES LEGEND FOOTING SCHEDULE CONCRETE SCHEDULE (U.N.O) (CSA A 23.1/A 23.2: TABLES 1 TO 5)

1. REFER TO FOUNDATION NOTES IN STRUCTURAL NOTES SECTION FOR ADDITIONAL INFO. FOOTING SIZE CONCRETE
TYPE DESCRIPTION REMARKS DESCRIPTION MIX REMARKS
MARK
LENGTH WIDTH DEPTH REINFORCEMENT STRENGTH
2. FOOTINGS SHALL BE PLACED ON NATURAL UNDISTURBED SOIL CAPABLE OF SUSTAINING
ALLOWABLE BEARING PRESSURE OF 100 kPa (ULS) FOR SQUARE FOOTINGS AND 90 kPa 8-15M BARS MUD MATS 15 MPa
(ULS) FOR STRIP FOOTINGS. REFER GEO TECH REPORT BY SOILS & MATERIALS 200MM WIDE POURED CONCRETE FOUNDATION WALL F1 1.6M 1.6M 0.41M T & B E.W.
ENGINEERING INC DATED APRIL 28 2020. FW-1 COMPLETE WITH 15M VERTICAL DOWELS SPACED AT 1.2M (4'-0") O.C. FILL CONCRETE FOR
WITH CONTINUOUS 15M TOP BAR 8-15M BARS
20 MPa
F2 1.6M 1.6M 0.41M MASONRY WALLS
3. THE BEARING CAPACITIES IN NOTE 2, ARE GENERALLY AVAILABLE AT DEPTHS OF >1.0M. B.E.W.
HOWEVER SOME LOCATIONS MAY REQUIRE ADDITIONAL SUBEXCAVATION. BEFORE FOOTINGS, PIERS, FOUNDATION WALLS FOR
25 MPa F2 MIX (**)
POURING CONCRETE THE BEARING CAPACITY SHALL BE VERIFIED BY THE GEO TECH FOUNDATION WALLS SHEAR WALLS SHALL BE 30 MPa 180 Eugenie Street West
CONSULTANT 6-15M BARS Windsor, ON N8X 2X6
F3 1.25M 1.25M 0.41M
T & B E.W. RETAINING WALLS 25 MPa F2 MIX (**) 519.258.1390

4. DEWATERING MAY BE REQUIRED FOR CONSTRUCTION OF FOOTINGS BECAUSE OF THE STRIP FOOTING TYPES LEGEND
HIGH GROUND WATER TABLE. THIS HAS TO BE DETERMINED BY GEOTECH CONSULTANT 6-15M BARS GARAGE FLOORS, STEPS,
F4 1.25M 1.25M 0.41M EXTERIOR SLABS 32 MPa C2 MIX
ONSITE.REFER GEO TECH REPORT BY SOILS & MATERIALS ENGINEERING INC DATED APRIL B E.W. PAVEMENTS, SIDEWALKS, CURBS
28 2020.
TYPE DESCRIPTION
INTERIOR CONCRETE FLOORS 25 MPa N-CF MIX INCLUDES SLAB ON GRADE
5. COORDINATE WITH ARCHITECTURAL DRAWINGS FOR ALL ELEVATIONS, RWL LOCATIONS, NOTES:
SLOPES ALL FOOTINGS TO BE EXTENDED TO DEPTH RECOMMENDED IN SOIL REPORT. BEAMS 30 MPa N MIX (*) (**)
SF-1 610MM WIDE x 305MM DEEP CONTINUOUS CONCRETE FOOTING SOIL BEARING CAPCITY BE VERIFIED BEFORE CONCRETE POUR.
6. ALL EXTERIOR FOOTINGS NEED TO BE EXTENDED TO DEPTHS OF A MINIMUM OF 1.2 M FOR COMPLETE WITH 3-15M CONTINOUS BOTTOM BARS FOR COMBINED FOOTINGS REFER PLAN This drawing is not to be used for
FROST PROTECTION AND DEEPER AS LISTED IN GEO TECHNICAL REPORT BORE HOLE COLUMNS 35 MPa N MIX (*) (**) construction unless it is countersigned
by the Project Architect
LOGS TO ACHIEVE SAFE BEARING CAPACITY
WALLS, SHEAR WALLS 35 MPa N MIX (*) (**) Issued For (YYMMDD)
7. ALL FOUNDATION WALLS SHALL HAVE (2) 15M CONT. TOP BARS PLACED 100mm BELOW THE PIER SCHEDULE TENDER 2020.06.01
TOP OF WALL U.N.O. ALL FOUNDATION WALLS SHALL HAVE 15M VERTICAL DOWELS TO
FOOTING AT 1200mm O.C. PIER SIZE * WHEN EXPOSED TO FREEZE THAW OR DEICING SALTS USE 5%-7% AIR ENTRAINMENT
REMARKS
MARK REINFORCEMENT ** WHEN SUBJECTED TO DEICING SALTS/CHLORIDE EXPOSURE USE C1-MIX 35 MPa UNO
LENGTH WIDTH
8. PROVIDE DOWELS w/ SIZE TO MATCH WALL REINFORCEMENT x 1200mm LONG, EMBEDDED 750MM WIDE x 305MM DEEP CONTINUOUS CONCRETE FOOTING FOR OTHER EXPOSURE CLASSES SULPHATES (S-CLASS) & MANURE (A-CLASS),
600mm IN TOP OF FOUNDATION AT WALL REINFORCEMENT LOCATIONS U.N.O. - TYP. SF-2 COMPLETE WITH 4 -15M CONTINUOUS BOTTOM BARS 4-20M VER
P1 0.41M 0.41M REFER TO BASE PLATE DETAIL NOTIFY EOR. R-CLASS MAY BE PERMITTED FOR SMALLER PROJECTS, NOTIFY EOR
C/W 10M TIES @305MM (12") O.C.
9. TOP OF PIERS AND TOP OF FOUNDATION WALLS AT ALL DOORS AND OTHER WALL
OPENINGS THAT EXTEND TO THE FLOOR SHALL BE 200mm BELOW FINISHED FLOOR.

10. PROVIDE WALL CONSTRUCTION JOINTS AS PER DETAILS AT THE START AND STOP OF
WALL POURING AS NECESSARY
COLUMN SCHEDULE
COLUMN DESCRIPTION
11. FOUNDATION CONTRACTOR TO COORDINATE WITH ALL TRADES, THE LOCATION OF ALL (4) ø25MM HOLES FOR CL MARK
PIPE SLEEVES PASSING THROUGH FOUNDATION WALLS. ADDITIONAL 15M REBAR TO BE ø19MM ANCHOR BOLTS
PROVIDED AROUND THE OPENING AS PER DETAILS. PIPING IS NOT TO RUN THROUGH 600MM LG. + 50MM HK. 3-PLY 38x140 BUILT UP SAWN LUMBER
FOOTINGS. FOOTINGS TO BE STEPPED DOWN TO SUIT. REER DETAILS. C1
COLUMN. SPF GRADE No.1/No.2
H.S.S. COLUMN

MIN
40
12. ALL DIMENSIONS TO BE COORDINATED WITH THE LATEST SET OF ARCHITECTURAL AT ALL STEEL COLUMNS
C2 4-PLY 38x140 BUILT UP SAWN LUMBER
DRAWINGS

300
CL COLUMN. SPF GRADE No.1/No.2
BASE PLATE 300MM

Date
13. ALL COLUMNS TO BE SET IN MINIMUM OF 40mm OF GROUT AS SPECIFIED (MASTERFLOW
OR EQUIVALENT). U/S OF B.PL's TO BE 200mm BELOW FINISHED FLOOR UNLESS NOTED x 300MM x 22MM FOR STEEL COLUMNS REFER PLAN
AND 450mm BELOW FINISHED FLOOR AT ALL RAIN WATER LEADER LOCATIONS 16929
100 3961 2889 3009 6869 100 40
14. THE BEARING CAPACITY TO BE SITE VERIFIED BEFORE POURING FOOTING
MIN
1500 2462 12967 300
B C CL E G B C CL E G
GRID 'H' TYP. BEARING PLATE DETAIL
P-1

Revision Schedule
P-1 P-1 CL OF WALL DEPRESSED SLAB
F-1 F-1 F-1 4 REFER TO ARCH DWGS.
FLOOR SLAB ON GRADE NOTES HSS5X5X3/8 SIM
S102
1 FW1 F-4 1

Description
138
HSS3-1/2X3-1/2X3/8

138
1. TYPICAL SLAB-ON-GRADE CONSTRUCTION

C1
200

200
102MM POURED CONCRETE FLOOR SLAB 1514 1495
2 2

176
w/ 152 x 152 - M.W. 13.3 x M.W. 13.3 W.W.M. (AT MID DEPTH)

176
HSS5X5X3/8
ON POLY VAPOUR RETARDER ON
SF-1 200 2451 200
137 2890 6769 100 100

2842
300MM GRANULAR 'A' COMPACTED TO 100% SPMDD ON

2642
2642

2642

2642
6 7 SF-1
GRANULAR 'B' TYPE 1 COMPACTED TO 98% SPMDD IN 250MM LOOSE LIFTS S102 119 S102
AS REQUIRED TO PROOF ROLLED AND APPROVED SUB BASE AS NOTED IN SF-2 SF-1 F-4
THE GEOTECHNICAL REPORT (REMOVE ALL ORGANIC AND FILL MATERIAL -

C1
F-2
3 3

200
TYP.)

196
IN ADDITION, SLAB CONSTRUCTION SHOULD INCORPORATE A CAPILLARY BREAK HSS5X5X3/8 SAWCUTS
CONSISTING OF 100MM CLEARSTONE GRAVEL (GRANULAR 'O' OPSS 1010) WHERE REFER

7486
4 F-4 4 FW1
4
2419
THE TOP OF FLOOR SLAB IS LOCATED BELOW THE GENERAL AREA GRADE TO TYP. SLAB

2223
SF-1 F-2 S102

No.
SF-2 SF-1

8845

9245
SAWCUT

2419
2. FINISHED FLOOR ELEVATION (TOP OF SLAB) = 0.00 MM TO MATCH EXISTING FINISHED DETAIL

C1
SIM
FLOOR
5 5
3. W.W.M. MUST BE SUPPORTED BY CHAIRS OR APPROVED MEANS AT 750MM O.C. EACH F-4
F-4

FOUNDATION PLAN & SAWCUT

2311

2311
WAY TO ENSURE IT IS PROPERLY HELD IN PLACE DURING THE CONCRETE POUR. SF-2 SF-1 3100 3100
FW1 F-2
SF-2 F-2

3540
F-4
4. PROVIDE 13MM THICK PRE-MOULDED JOINT FILLER AGAINST INTERIOR FOUNDATION

C1
8

C2
WALLS AND ALL OTHER VERTICAL SURFACES.
6 CL OF POST S102 6
5. MAINTAIN THE SPECIFIED SLAB THICKNESS AT ALL FLOOR DEPRESSIONS. SF-1 SAWCUTS
F-4 5
SIM S102 FW1 SF-2 REFER
3000

3000
6. PROVIDE TRANSVERSE REINFORCED TCHIKENED SLABS AS PER DETAIL BELOW ALL FW1 TO TYP. SLAB
SF-2
ONE STOREY MASONRY WALLS WITHOUT FOUNDATION WALL BELOW 4 SF-2 SIM SF-1 SAWCUT
F-2
14191

13991
S102 F-4 DETAIL
F-2 4
7. UNO PROVIDE SAWCUTS AS DETAILED AT THE LOCATIONS SHOWN ON PLAN.

C1
C1

C2
S102
8. PROTECT SLAB-ON-GRADE AND BASE AGAINST FREEZING AND FROST ACTION AS
7 SIM 7
REQUIRED AT ALL TIMES DURING CONSTRUCTION. F-4
1500 200 5169 200 2847 200 5112 200 1500 2300 2300 2700 2350 2350
3020

3020
9. PROVIDE SLAB THICKENING UNDER ALL BLOCK PARTITION WALLS
SF-2 SF-2 SF-2 FW1
F-2 F-2
26209

7987

7987
C1

1250
8 8

LAYOUT
F-4 F-4
SF-2 5 1250
SF-2 S102
3550

3550
SF-1 4 P-1
SLAB THICKENING UNDER CMU WALL W/ JOINT REINF. AT
NON- LOAD BEARING EVERY SECOND COURSE (TYP) F-2 F-2 S102 F-1
PARTITION WALLS SF-1 SF-1 SF-1 SF-1 SF-1
SIM
C2

C1
C1

200

200
SAWCUT ON EITHER SIDE
9 HSS5X5X3/8
9
P-1

John R. Park Homestead Heritage Centre

CONCRETE FLOOR SLAB 5
F-4 S102
C/W WWM HSS5X5X3/8

915 County Road 50, Essex, Ontario N0R 1G0

3075

3075
SF-1 1250
STOP INSULATION ON EITHER HSS5X5X3/8 P-1
SIDE OF THICKENED SLAB F-4 F-1
BIM 360://2020 JRPH Heritage Centre/2020 STRUCT-360.rvt

P-1
203 203
C1

F-3
1250

1250
10 HSS5X5X3/8 10
[UNO]
102

SAWCUTS REFER
1250 3 TO TYP. SLAB
2472

2472
9176

8776

S102 8776

8976
1 P-1 SAWCUT
2 SF-1 F-1 DETAIL
3-15M CONT HSS5X5X3/8
C1

F-4
11 1600 11
BASE, SUB BASE
P-1 HSS5X5X3/8
203 BLOCK 203 F-3
4
WIDTH UNDISTRUBED
S102 SF-1 SF-1 1600
SOIL
3092

3092
P-1 2
F-1 S102 F-1 P-1 3000 3000 3000 3000
F-4 P-1 F-1
SF-1 F-1 SF-1 SF-1
C1

1
12 12
133 181

200

S102
5 SAWCUT JOINT
FW1
GREATER (3/16") 10M @ 300
10M @ 300
FOR COVER & FRAME SEE
MECH. & ARCH. DRAWINGS 13 HSS5X5X3/8 HSS5X5X3/8
13
OF t/4 t EACH WAY HSS5X5X3/8 HSS5X5X3/8

ERCA
OR 25.4MM (1") EACH WAY 1-15M CONT. 12906 2522 1500
GRID 'A'
CL OF WALL
900 (36")

t
A D F H
MAX.

t 1
1 2 A D F
2 2t Drawn By Checked By
ai ai
6/1/2020 10:02:46 AM

NOTE:
SAW CUT DETAIL (TYP) WHEN THE GENERAL CONTRACTOR IS LOCATING
Project No
FLOOR TRENCH THE BUILDING THEY SHALL REFERENCE FROM N N
200 STEP THE EXISTING GIFT SHOP DUE TO SPATIAL 2020
(8") DIMENSIONS ARE mm, EXCEPT DIMENSIONS IN BRACKETS ARE INCHES SEPARATION; REFER TO SITE PLAN FOUNDATION PLAN SLAB ON GRADE PLAN
THIS LINE IS 4" LONG
SCALE: 1 : 100 SCALE: 1 : 100 Sheet No

100
REFER TO PLAN REFER TO PLAN

100
180 Eugenie Street West
1ST FLOOR 1ST FLOOR 1ST FLOOR 1ST FLOOR 1ST FLOOR Windsor, ON N8X 2X6
519.258.1390

100
0 0 0 0 0
200

200

200
FIN. GRADE FIN GRADE
200 VAPOUR BARRIER TYP. VAPOUR BARRIER TYP.
100 REFER TO ARCH. REFER TO ARCH.
POURED CONCRETE PIER POURED CONCRETE PIER 100MM SOG C/W/ W.W.M. @
REFER TO SCHEDULE REFER TO SCHEDULE M.H. ON 2 - 38MM LAYERS OF 25 INSULATION TYP. INSULATION TYP.
INSULATION TYP.

915

915
HD STYROFOAM INSULATION REFER TO ARCH. REFER TO ARCH.
(8) - 20M VERT. (8) - 20M VERT. REFER TO ARCH.
715

715

1220

1220
REINF. BARS REINF. BARS 10M L SHAPED DOWELS 200MM POURED CONCRETE INSULATION TYP. 200MM POURED CONCRETE 200MM POURED CONCRETE

1321

1321
300MM x 400MM LLV @ FOUNDATION WALL w/ 15M REFER TO ARCH. FOUNDATION WALL w/ 15M FOUNDATION WALL w/ 15M
10M TIES @ 300MM O.C. 10M TIES @ 300MM O.C. 205 138 62 205 VERT. DOWELS 600MM w/
600MM O.C. TYP. VERT. DOWELS 600MM w/ VERT. DOWELS 600MM w/ INSULATION TYP. This drawing is not to be used for
construction unless it is countersigned
152MM HOOK @ 1220MM 152MM HOOK @ 1220MM REFER TO ARCH. 152MM HOOK @ 1220MM by the Project Architect

INSULATION TYP.
REFER TO ARCH. 610MM x 300MM THK. 610MM x 300MM THK. 610MM x 300MM THK. Issued For (YYMMDD)

305

305
POURED CONC. FOOTING w/
406

406
F-1 F-1 POURED CONC. FOOTING w/ POURED CONC. FOOTING w/ TENDER 2020.06.01
3 - 15M CONT. BOTTOM BARS 3 - 15M CONT. BOTTOM BARS 3 - 15M CONT. BOTTOM BARS

UNDISTURBED SOIL, TYP. UNDISTURBED SOIL, TYP.

610 UNDISTURBED SOIL, TYP. POURED CONCRETE FOOTING
610
UNDISTURBED SOIL, TYP. BEYOND REFER TO SCHEDULE
UNDISTURBED SOIL, TYP. POURED CONCRETE FOOTING POURED CONCRETE FOOTING
REFER TO SCHEDULE REFER TO SCHEDULE
1 SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION
S101 SCALE: 1 : 20 S101 SCALE: 1 : 20 S101 SCALE: 1 : 20 S101 SCALE: 1 : 20 S101 SCALE: 1 : 20

B C

Date
DOOR TYP.
REFER TO ARCH
SAWCUT TYP. H
DOOR TYP. BUILT UP WOOD POST
152MM SOG C/W/ REFER TO ARCH REFER TO FRAMING PLAN
INSULATION TYP. W.W.M. @M.H.
REFER TO ARCH. 2-15M CONT. TOP BARS SAWCUT TYP SIDING TYP. 13MM PREMOULDED
DEPRESSED SLAB REFER TO ARCH. JOINT (TYP)
13MM CHAMFER
REFER TO ARCH DWGS. 152MM SOG C/W/ 100MM SOG C/W/
REFER TO ARCH. TYP.
W.W.M. @M.H. W.W.M. @M.H. 2-15M CONT. TOP BARS 100MM SOG C/W/

Revision Schedule
W.W.M. @M.H.

200
13

1ST FLOOR 1ST FLOOR 1ST FLOOR

102 50

100
0 0 0
200
200

Description
FIN GRADE
75 100 15M BAR AROUND VAPOUR BARRIER TYP.
DEPRESSED SLAB PERIMETER REFER TO ARCH.
2-15M CONT. TOP BARS 25 INSULATION TYP.
INSULATION TYP. 200 137
915

915

915
REFER TO ARCH. REFER TO ARCH.
100MM SOG C/W/ W.W.M. @ 46 154
1220

1220
M.H. ON 2 - 38MM LAYERS OF 200MM POURED CONCRETE 200MM POURED CONCRETE INSULATION TYP. 200MM POURED CONCRETE

1321
HD STYROFOAM INSULATION FOUNDATION WALL w/ 15M FOUNDATION WALL w/ 15M REFER TO ARCH. 200 FOUNDATION WALL C/W/ 15M
205 100 100 205 205 205
10M L SHAPED DOWELS VERT. DOWELS 600MM w/ 10M L SHAPED DOWELS VERT. DOWELS 600MM w/ VERT. DOWELS @ 1220MM
300MM x 400MM LLV @ 152MM HOOK @ 1220MM 300MM x 400MM LLV @ 152MM HOOK @ 1220MM
600MM O.C. TYP. 600MM O.C. TYP.
610MM x 300MM THK. 610MM x 300MM THK.
305

305

No.
INSULATION TYP.

406
REFER TO ARCH. POURED CONC. FOOTING w/ POURED CONC. FOOTING w/ F-4
3 - 15M CONT. BOTTOM BARS 3 - 15M CONT. BOTTOM BARS
UNDISTURBED SOIL, TYP. UNDISTURBED SOIL, TYP.
610 610 UNDISTURBED SOIL, TYP. POURED CONCRETE FOOTING
REFER TO SCHEDULE

6 SECTION 7 SECTION 8 SECTION

S101 SCALE: 1 : 20 S101 SCALE: 1 : 20 S101 SCALE: 1 : 20

FOUNDATION SECTIONS
John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 STRUCT-360.rvt

ERCA
Drawn By Checked By
ai ai
6/1/2020 10:02:48 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

3.0 SEISMIC LOAD PARAMETERS

Issued For (YYMMDD)

Ie = 1.0 TENDER 2020.06.01

Sa(0.2) = 0.114g, Sa(0.5) = 0.07g, Sa(1.0) = 0.038g, Sa(2.0) = 0.018g, PGA = 0.069g 3 HSS TO LVL (U-BRACKET) CONNECTION DETAIL AT VESTIBULE 4 HSS TO LVL (U-BRACKET) CONNECTION DETAIL-1 (TYP) 5 HSS TO LVL (U-BRACKET) CONNECTION DETAIL-1 (TYP) 6 CANOPY FRAMING
SITE RESPONSE CLASS = 'E' [Refer Soils Report By Soils & Materials Engineering Inc]
Rd = 3.0, Ro = 1.7 (Nailed Shear Walls Wood Based Panels) S201 SCALE: 1 : 20 S201 SCALE: 1 : 20 S201 SCALE: 1 : 20 S201 SCALE: 1 : 20
Ta = 0.25 s Mv = 1.0
W used = 533.35 kN [1.0 Dead + 0.25 Snow]
Vx = 18.08 kN
Vy = 18.08 kN

4.0 WIND LOAD PARAMETERS

q(1/50) = 0.47 kPa

Building Exposure: Open
Building Openings: Category 2
Building Importance: Normal
Vx = 176 kN
Vy = 62 kN

GROSS WIND UPLIFT DIAGRAM CL CL

DESIGN OF TRUSSES LABELLED AS G01, G02, G03, BEAM LABEL BOTTOM PLATE SIZE IN U-BRACKET
G04, FG01 & FG02 AND TWO MORE ARE BY (DETAIL 3,4&5 OF S201)
END ZONE WIDTH (TYP)

CORNER OTHERS.SUBMIT STAMPED SHOP DRAWINGS.

Date
ZONE
-1.7 kPa RB - 2-2x10 No.1&2 SPF NA
Z=1.3M

BM1 - 4-2x8 LVL PLATE 2 TO BE 250mm X 214mm X12.7mm

EXTENT OF LOW ROOF BM2 - 3-2x8 LVL PLATE 2 TO BE 250mm X 170mm X12.7mm
B C E F G AT VESTIBULE B C E F G BM3 - 2-2x8 LVL PLATE 2 TO BE 250mm X 120mm X12.7mm
3 6
S201 S201
3 6 2"x8" No. 1&2 SPF

Revision Schedule
S201 DIMENSIONAL
1
S201
1 LUMBER JOISTS @
1289 2889
300mm O.C. HSS5X5X3/8
.
INTERIOR EDGE

Description
INTERIOR
ZONE
-1.4 kPa
ZONE
-1.4 kPa
ZONE
-1.7 kPa
2 2 BM2
G04 SW1 G01

3261
3 SW2

RB
S701 3
S701
3 HSS5X5X3/8 3

3 S601
3 G04 G01
S601

G01 SW1
4 4

FG01
RB
2223
TIE 2x8 JOISTS
INTO PERIMETER

No.
STUD WALL
Z = 1.3 M 5 BEAM TO BE
5 G01 G03 G01
END ZONE WIDTH (TYP) SUPPORTED ON

2311

RB
STUD WALL AT THIS
SW2
END

ROOF & MEZZANINE FRAMING

2X12 SPF LUMBER G01 G03 G01
6 JOISTS @ 305mm O.C.
@ STAIR LANDING 6

RB
3000
2X10 SPF LUMBER
BLOCKING @ 305mm
O.C. (TYP)

7 SOLID WD 2"x6" COL'S

BEARING ON FLOOR
7
TRUSS TO BE SIZED BY TRUSS TYPE STRUCTURE REFER 2/601
JOISTS
OTHERS
BUILT-UP 3PLY - 1 3/4" X

3020

RB
1 3/4" X 9 1/2" AJS 25 DBL - 1 3/4" X 9 1/2" AJS 9 1/2" AJS 25 PRE-ENG
PRE-ENG JOIST OR 25 PRE-ENG JOIST OR JOIST OR EQUIV.

25937
EQUIV. @ 305mm O.C. EQUIV. @ 305mm O.C.
2 2
8 S601 8 S601
TRUSS TO BE SIZED
. BY TRUSS TYPE STRUCTURE REFER 2/601
OTHERS

PLANS
5 5

RB
3550
S201 SW2 S201

HSS5X5X3/8 SW1
HSS5X5X3/8
9 2X10 SPF LUMBER
9 G01 G02 BM2
BLOCKING @ 305mm G03

John R. Park Homestead Heritage Centre

O.C. (TYP)
2X12 SPF LUMBER

3075

3075
RB
BLOCKING @ 305mm 5330

915 County Road 50, Essex, Ontario N0R 1G0

O.C. (TYP)
HSS5X5X3/8
BIM 360://2020 JRPH Heritage Centre/2020 STRUCT-360.rvt

4 G01 G03 G02 4

10 S201 10 S201
4114 BM1 1216 2"X8" SPF No. 1&2
HSS5X5X3/8 DIMENSIONAL

FG02

FG02
2472

2472
RB
LUMBER JOISTS @
300mm O.C.

1 G01 G03 G02 1

11 S601 11 BM1
S601
HSS5X5X3/8 HSS5X5X3/8
DOUBLE DIAGONAL

3092

3092
HATCH DENOTES EXTENT OF LOW

RB
EXTENT OF SHEAR SW2 ROOF AT OUTDOOR
WALL 2 (SW2) HSS5X5X3/8 SPACE. REFER ARCH
SW1 FOR COMPOSITION
G01 G03 G02 BM2
12 4 12
181

S701
HSS5X5X3/8
13 13
DIAGONAL HATCH
EXTENT OF LOW
A D 4
H DENOTES EXTENT OF
SHEAR WALL 1 (SW1) 12668
4
S601
ROOF AT
4114
OUTDOOR SPACE

ERCA
S601

2 MEZZANINE FRAMING PLAN

A D H
S201 SCALE: 1 : 100 Drawn By Checked By
ai ai
6/1/2020 10:02:51 AM

Project No
2020
1 ROOF FRAMING PLAN THIS LINE IS 4" LONG
Sheet No
S601 SCALE: 1 : 100

T/O RIDGE BEAM

8392
RAFTER BELOW TO ALIGN
WITH SLOPE OF TRUSS
H G F
REFER ARCHITECTURAL
FOR ROOF COMPOSITION This drawing is not to be used for
T.O.GIRDER TRUSS T.O.GIRDER TRUSS construction unless it is countersigned
6700 6700 by the Project Architect

Issued For (YYMMDD)

TENDER 2020.06.01
3-PLY 44X184 LVL
RAFTER
REFER PLAN FOR
TRUSS LABELS

VERTICAL POST OF 3-
PLY 2x6 SUPPORTED
ON FLOOR JOISTS

REFER PLAN FOR

TRUSS LABELS
BUILTUP WOOD POST
WITHIN WALL

MEZZANINE
MEZZANINE
2910
2910 T/O WALL PLATE
2650

BM1
T.O. CANOPY WD. JOISTS

Date
REFER PLAN BUILT-UP 3PLY - 1 3/4" X
REFER PLAN FOR 9 1/2" AJS 25 PRE-ENG
TRUSS LABELS JOIST OR EQUIV.
2756

HSS5X5X3/8 HSS5X5X3/8 BUILTUP WOOD POST

WITHIN WALL BUILTUP WOOD POST BUILTUP WOOD POST
WITHIN WALL WITHIN WALL

Revision Schedule
1ST FLOOR 1ST FLOOR
0 0

Description
4
S102

1 BUILDING SECTION ALONG GRID LINE - 11 2 BUILDING SECTION ALONG GRID LINE - 8

No.
S201 SCALE: 1 : 50 S201 SCALE: 1 : 50

13 12
H G F E CL D C B A REFER ARCH DRAWINGS
FOR ROOF COMPOSITION
RIDGE BEAM 181

FRAMING SECTIONS
T/O RIDGE BEAM
8392

T.O.GIRDER TRUSS
6700

T.O.GIRDER TRUSS CLIP ANGLE

6700 BRACKET FOR
CONNECTION BY
OTHERS (TYP)

REFER PLAN FOR

TRUSS LABELS

John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

HSS8X4X3/8
MEZZANINE
BIM 360://2020 JRPH Heritage Centre/2020 STRUCT-360.rvt

3 2910
T/O WALL PLATE
S701 2650
MEZZANINE 2X8 CANOPY
2910
T/O WALL PLATE FRAMING CLIP ANGLE
2650 BRACKET FOR
CONNECTION BY
OTHERS (TYP)
HSS5X5X3/8
T.O. WD. JOIST
U/S OF H.S.S.

2756
2578

1ST FLOOR
0

ERCA
REFER FOUNDATION
PLAN FOR DETAILS
Drawn By Checked By
4 SECTION ai ai
6/1/2020 10:02:53 AM

S201 SCALE: 1 : 50 Project No

3 BUILDING SECTION ALONG GRID LINE - 3 2020

S201 SCALE: 1 : 50 THIS LINE IS 4" LONG
Sheet No

T/O RIDGE BEAM T.O.GIRDER TRUSS

8392 6700
REFER PLAN FOR
TRUSS LABELS
180 Eugenie Street West
Windsor, ON N8X 2X6
REFER ARCH DETAILS FOR 519.258.1390
ROOF COMPOSITION

38X140 SPF DIMENSIONAL

T.O.GIRDER TRUSS LUMBER BLOCKING @
6700 38X140 SPF 1200mm O.C. MAX.
DIMENSIONAL LUMBER
DOUBLE TOP PLATE
FG TRUSS
BEYOND.
REFER PLAN
REFER PLAN FOR This drawing is not to be used for
REFER PLAN FOR construction unless it is countersigned
TRUSS LABELS HSS5X5X3/8 by the Project Architect
TRUSS LABELS

Issued For (YYMMDD)

HSS5X5X3/8 TENDER 2020.06.01
MEZZANINE 12.5mm THICK DOUGLAS FIR-
HSS5X5X3/8 2910
T/O WALL PLATE LARCH PLYWOOD ON EACH SIDE
2650 OF STUDS C/W/ 3.25mm NAILS W/
38mm MIN PENETRATION @
BUILT UP WOOD 75mm O.C. AT PANEL EDGES AND
5 COLUMN REFER PLAN @ 150mm O.C. @ INTERMEDIATE
S201 STUDS
MEZZANINE
2910 4-16mm DIA ANCHOR
T/O WALL PLATE 38X140 SPF BOLTS W/ MIN 150mm
2650 DIMENSIONAL LUMBER EMBEDMENT AND
STUDS @ 300mm O.C. 70mm HOOK C/W/
HSS8X4X3/8 HSS8X4X3/8 70mm X 6mm THICK
SQUARE WASHER @
1ST FLOOR EACH END OF SHEAR
HSS5X5X3/8 HSS5X5X3/8 HSS5X5X3/8
HSS5X5X3/8 0 WALL

Date
S102 38X140 SPF
DIMENSIONAL LUMBER ANCHOR BOTTOM
BOTTOM PLATE PLATE TO
FOUNDATION WALL W/
1ST FLOOR 12.7mm ANCHORS @
0 1200mm O.C.
FOR FOUNDATION DETAILS REFER
FOUNDATION PLAN & SECTIONS 4 SW-1 SHEAR WALL ELEVATION

Revision Schedule
S201 SCALE: 1 : 50

Description
12.5mm GYPSUM BOARD 12.5mm GYPSUM BOARD
1 SOUTH ELEVATION
NAIL SHEATHING PANELS TO NAIL SHEATHING PANELS TO
SCALE: 1 : 50 38X140 SPF DIMENSIONAL 38X140 SPF DIMENSIONAL
STUDS W/ 3.25mm DIA. NAILS W STUDS W/ 3.25mm DIA. NAILS W
LUMBER STUDS @ 300mm O.C. LUMBER STUDS @ 300mm O.C.
38mm NAIL PENETRATION MIN. 38mm NAIL PENETRATION MIN.
SPACED @ 75mm O.C. @ SPACED @ 75mm O.C. @
PANEL EDGES PANEL EDGES
12.5mm THICK DOUGLAS FIR- 12.5mm THICK DOUGLAS FIR-
LARCH PLYWOOD ON EACH LARCH PLYWOOD ON EACH
SIDE OF STUDS SIDE OF STUDS

No.
NAIL SHEATHING PANELS TO NAIL SHEATHING PANELS TO
STUDS W/ 3.25mm DIA. NAILS W NAIL SHEATHING PANELS TO STUDS W/ 3.25mm DIA. NAILS W NAIL SHEATHING PANELS TO
38mm NAIL PENETRATION MIN. STUDS W/ 3.25mm DIA. NAILS W 38mm NAIL PENETRATION MIN. STUDS W/ 3.25mm DIA. NAILS W
SPACE@ 150mm O.C. @ 38mm NAIL PENETRATION MIN. SPACE@ 300mm O.C. @ 38mm NAIL PENETRATION MIN.
INTERMEDIATE STUDS
H G F E CL D C B A SPACED @ 75mm O.C. @
PANEL EDGES
INTERMEDIATE STUDS SPACED @ 100mm O.C. @
PANEL EDGES

T/O RIDGE BEAM

SW1-SHEAR WALL PLAN SECTION SW2-SHEAR WALL PLAN SECTION

FRAMING ELEVATIONS
REFER PLAN FOR RIDGE BEAM 8392
TRUSS LABELS SCALE: 1 : 20 SCALE: 1 : 20

T.O.GIRDER TRUSS
6700
MEZZANINE MEZZANINE
REFER PLAN FOR 2910 2910
TRUSS LABELS FG TRUSS
BEYOND. REFER ARCH DETAILS
FOR ROOF COMPOSITION
5482

REFER PLAN

8364
38X140 SPF
12.5mm THICK DOUGLAS FIR-
DIMENSIONAL LUMBER
LARCH PLYWOOD ON EACH SIDE
REFER PLAN FOR DOUBLE TOP PLATE
OF STUDS C/W/ 3.25mm NAILS W/
TRUSS LABELS 38mm MIN PENETRATION @
100mm O.C. AT PANEL EDGES
AND @ 300mm O.C. @

John R. Park Homestead Heritage Centre

5 INTERMEDIATE STUDS
6
3 3

915 County Road 50, Essex, Ontario N0R 1G0

S201 S201
S201 S701 MEZZANINE
2910 BUIL UP WOOD
BIM 360://2020 JRPH Heritage Centre/2020 STRUCT-360.rvt

COLUMN REFER TO
T/O WALL PLATE PLAN
2650
38X140 SPF
HSS8X4X3/8 DIMENSIONAL LUMBER
BLOCKING @ 1200mm
MEZZANINE FRAMING BEYOND MAX.
HSS5X5X3/8 HSS5X5X3/8 REFER PLANS 38X140 SPF
BUILTUP WOOD POST DIMENSIONAL LUMBER
HSS3-1/2X3-1/2X3/8 STUDS @ 300mm O.C.
WITHIN EXTERIOR WALL
5
ANCHOR BOTTOM
S102
PLATE TO 3-12.7mm DIA ANCHOR
FOUNDATION WALL W/ BOLTS W/ MIN 125mm
EMBEDMENT AND
12.5mm DIA ANCHORS
38X140 SPF 60mm HOOK C/W/
1ST FLOOR @ 1200mm O.C.
DIMENSIONAL LUMBER 64mm X 5mm THICK
0 BOTTOM PLATE SQUARE WASHER @
EACH END OF SHEAR
FOR FOUNDATION DETAILS REFER WALL
FOUNDATION PLAN & SECTIONS

ERCA
Drawn By Checked By
ai ai
6/1/2020 10:02:58 AM

3 SW2-SHEAR WALL ELEVATION Project No

S201 SCALE: 1 : 20 2020
2 NORTH ELEVATION THIS LINE IS 4" LONG
Sheet No
SCALE: 1 : 50

T/O RIDGE BEAM

8392
4 180 Eugenie Street West
Windsor, ON N8X 2X6
REFER PLAN FOR S701 519.258.1390
TRUSS LABELS REFER PLAN FOR
TRUSS LABELS

T.O.GIRDER TRUSS
6700

REFER PLAN FOR FG TRUSS REFER PLAN

TRUSS LABELS This drawing is not to be used for
construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

REFER ARCH DETAILS FOR TENDER 2020.06.01
HSS5X5X3/8 ROOF COMPOSITION

MEZZANINE FRAMING
BEYOND REFER PLANS
MEZZANINE
2910
T/O WALL PLATE
2650
HSS8X4X3/8

HSS3-1/2X3-1/2X3/8
HSS5X5X3/8 BUILT UP WOOD BUILT UP WOOD
POST WITHIN POST WITHIN
EXTERIOR WALL EXTERIOR WALL

Date
1ST FLOOR
0
FOR FOUNDATION DETAILS REFER

Revision Schedule
FOUNDATION PLAN & SECTIONS

Description
1 EAST ELEVATION
SCALE: 1 : 50

No.
13 12 11 10 9 8 7 6 5 4 3 2 1

T/O RIDGE BEAM

FRAMING ELEVATIONS
REFER ARCH REFER ARCH 8392
DETAILS FOR ROOF DETAILS FOR ROOF
COMPOSITION COMPOSITION

T.O.GIRDER TRUSS
6700

REFER PLAN FOR

TRUSS LABELS REFER PLAN FOR
TRUSS LIKE
STRUCTURE REFER TRUSS LABELS
3/601

MEZZANINE FRAMING

John R. Park Homestead Heritage Centre

BEYOND REFER PLANS

915 County Road 50, Essex, Ontario N0R 1G0

HSS8X4X3/8 HSS8X4X3/8 HSS8X4X3/8
BEYOND BEYOND BEYOND
BIM 360://2020 JRPH Heritage Centre/2020 STRUCT-360.rvt

MEZZANINE
2910
T/O WALL PLATE
2650
3-PLY JOISTS
REFER PLAN

HSS5X5X3/8 HSS5X5X3/8 HSS5X5X3/8 HSS5X5X3/8

BUILT UP WOOD
POST WITHIN
EXTERIOR WALL

BUILT UP WOOD
POST WITHIN
EXTERIOR WALL
1ST FLOOR
0
FOR FOUNDATION DETAILS REFER
FOUNDATION PLAN & SECTIONS

ERCA
Drawn By Checked By
ai ai
6/1/2020 10:03:01 AM

Project No

2 WEST ELEVATION 2020

THIS LINE IS 4" LONG
SCALE: 1 : 50 Sheet No

DOMESTIC COLD WATER MV MANUAL AIR VENT

FD
DOMESTIC HOT WATER FLOOR DRAIN

DOMESTIC HOT WATER RETURN BACK FLOW PREVENTOR

180 Eugenie Street West
Windsor, ON N8X 2X6
519.258.1390

SAN SANITARY PIPING PRESSURE GAUGE COCK

ST STORM PIPING T THERMOSTAT

CO2
F FIRE PROTECTION STANDPIPE SYSTEM S CARBON DIOXIDE SENSOR

This drawing is not to be used for

construction unless it is countersigned
SP FS FLOW SWITCH by the Project Architect
FIRE PROTECTION SPRINKLER SYSTEM

Issued For (YYMMDD)

G G GAS METER TENDER 2020.06.01

NATURAL GAS M

HWHR HOT WATER HEATING RETURN W WATER METER

HWHS HOT WATER HEATING SUPPLY UPRIGHT SPRINKLER HEAD C/W GUARD

CHWR CHILLED WATER HEATING RETURN CONCEALED SPRINKLER HEAD C/W GUARD

CHWS CHILLED WATER HEATING SUPPLY FIRE DEPARTMENT CONNECTION

RL REFRIGERANT LIQUID FEX FIRE EXTINGUISHER - SURFACE MOUNTED

RS REFRIGERANT SUCTION NEW DUCTWORK

Date
SHUT OFF VALVE FLAT OVAL DUCTWORK

CHECK VALVE ROUND DUCTWORK

Revision Schedule
PRESSURE REDUCING VALVE INTERNALLY INSULATED DUCTWORK

Description
TWO WAY CONTROL VALVE ALUMINUM DUCTWORK

BD
THREE WAY CONTROL VALVE BALANCING DAMPER

TPV RV BDD
TEMPERATURE PRESSURE RELIEF VALVE (TPV) OR
BACKDRAFT DAMPER
PRESSURE RELIEF VALVE (RV)

FD
BALL VALVE FIRE DAMPER

No.
SD-1
FCV FLOW CONTROL VALVE SOUND ATTENUATOR

COMBINATION SHUT OFF & BALANCING VALVE SUPPLY DIFFUSER / GRILLE / REGISTER

SV SUPERVISED VALVE RETURN GRILLE / REGISTER

HOSE BIBB EXHAUST GRILLE / REGISTER

MECHANICAL LEGEND
DRAIN WITH HOSE CONNECTION WALL FIN ENCLOSURE AND ELEMENT

SPRINKLER SYSTEM ALARM CHECK VALVE FORCE FLOW HEATER OR FAN COIL UNIT

GREASE INTERCEPTOR A1 PLUMBING FIXTURE TAG DESIGNATION

0.00
CO CLEANOUT IN WALL VALVE FLOW RATE
GPM

CO CLEANOUT PLUG EF-1 MECHANICAL EQUIPMENT TAG

CO CLEANOUT IN FLOOR
SD-1 TYPE
100 AIR QUANTITY (CFM)

John R. Park Homestead Heritage Centre

UNION

915 County Road 50, Essex, Ontario N0R 1G0

CONCENTRIC REDUCER
SD-1 TYPE
100 ELEMENT LENGTH (INCHES)
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

STRAINER

STRAINER C/W BLOW OFF

PUMP

THERMOMETER

PRESSURE GAUGE

S AIR SEPARATOR

ERCA
FLEXIBLE CONNECTOR

FLANGES
Drawn By Checked By

AV ai ai
6/1/2020 9:20:12 AM

AUTOMATIC AIR VENT

Project No
2020
THIS LINE IS 4" LONG
Sheet No

1. CODES AND STANDARDS 14. FIRE PROOFING 2. FITTINGS

1.1 ALL WORK SHALL CONFORM TO THE MOST RECENT ISSUES OF: 14.1. THE EXISTING CEILING SPACE CONTAINS FIRE PROOFING SPRAY ON THE 2.1. STEEL PIPE FITTINGS, SCREWED, FLANGED OR WELDED: 24. PROVIDE AND INSTALL NEW DISCONNECT SWITCHES AND UNIT MOUNTED OUTDOOR
1.1.1. THE ONTARIO BUILDING CODE STRUCTURAL ELEMENTS. REPAIR/RE-INSTATE ANY FIRE PROOFING IN THE CEILING 2.1.1. MALLEABLE IRON: SCREWED, BANDED, CLASS 150. 120V DUPLEX GFCI RECEPTACLES. DUPLEX GFCI RECEPTACLES ON UNIT SHALL BE ON
1.1.2. THE ONTARIO ELECTRICAL SAFETY CODE SPACE THAT IS DISTURBED AS A RESULT OF THESE DIVISIONS. 2.1.2. STEEL PIPE FLANGES AND FLANGED FITTINGS: TO ANSI/ASME B16.5 SEPARATE ELECTRICAL CIRCUIT THAN UNIT AND HAVE ITS OWN BREAKER.
1.1.3. THE MINISTRY OF THE ENVIRONMENT 2.1.3. WELDING: BUTT-WELDING FITTINGS.
1.1.4. THE NATIONAL ELECTRICAL CODE 15. ELECTRICAL 2.1.4. UNIONS: MALLEABLE IRON, BRASS TO IRON, GROUND SEAT, TO ASTM A47M 25. SUPPLY ELECTRICAL EQUIPMENT AND ACCESSORIES REQUIRED TO HAVING A FULLY
1.1.5. BYLAWS AND REGULATIONS ISSUED BY THE BUILDING AUTHORITY 15.1. ALL LOW VOLTAGE CONTROL WIRING (<50V) SHALL BE BY DIVISION 16, TO ELECTRICAL 2.1.5. BOLTS AND NUTS: TO ANSI B18.2.1. FUNCTIONAL SYSTEM REFER TO DRAWINGS AND SPECIFICATIONS FOR MORE DETAILS.
HAVING JURISDICTION DIVISION STANDARDS. 2.1.6. NIPPLES: SCHEDULE 40, TO ASTM A53. 180 Eugenie Street West
1.1.6. ASHRAE Windsor, ON N8X 2X6
15.2. ALL ELECTRICAL WIRING (+50V) SHALL BE BY DIVISION 16, TO ELECTRICAL DIVISION 2.2. COPPER PIPE FITTINGS, SCREWED, FLANGED OR SOLDERED 26. ALL ABANDONED ELECTRICAL SWITCHES AND PANELS TO BE REMOVED AND DISPOSED. 519.258.1390
1.1.7. ASME STANDARDS. 2.2.1. CAST COPPER FITTINGS: TO ANSI B16.18.
1.1.8. SMACNA 2.2.2. WROUGHT COPPER FITTINGS: TO ANSI/ASME B16.22 27. BALANCE THE AIRFLOW THROUGH ALL EXISTING DIFFUSERS ON THE GROUND FLOOR TO
1.1.9. NFPA 16. AS BUILT DRAWINGS ENSURE REQUIRED CFMIS PROVIDED AS INDICATED ON THE DRAWING. PROVIDE
1.1.10. TSSA 16.1. MAINTAIN A RECORD OF ALL REVISIONS. PREPARE RECORD DRAWINGS IN A NEAT 3. VALVES BALANCING REPORT FOR ENGINEER TO REVIEW AND SIGN-OFF.
1.1.11. CSA MANNER SHOWING ALL DEVIATIONS IN WORK. ON COMPLETION OF WORK, SUBMIT TO 3.1. PROVINCIAL CODE APPROVED, LUBRICATED PLUG TYPE.
1.1.12. CGA THE ENGINEER ONE HARD COPY OF AS BUILT DRAWINGS AND ELECTRONIC FORMAT 28. COMMISSION AND START-UP OF SYSTEM WITH MANUFACTURER SIGN-OFF.
1.1.13. COORDINATE AND PAY FOR ALL TSSA INSPECTIONS. DRAWINGS (IN AUTOCAD). 4. INSTALLATION
4.1. INSTALL IN ACCORDANCE WITH APPLICABLE PROVINCIAL CODES. 29. TEST, COMMISSION AND BALANCE ALL AFFECTED EQUIPMENT AND SYSTEMS.
2. SPECIFICATIONS 17. OPERATION AND MAINTENANCE MANUALS 4.2. INSTALL IN ACCORDANCE WITH CAN/CGA B149.1.
2.1 COMPLY WITH THE GENERAL SECTIONS AND APPLICABLE SECTIONS OF THE 17.1. SUBMIT 5 COPIES OF O&M MANUALS TO ENGINEER FOR REVIEW. ALSO INCLUDE 1 4.3. ASSEMBLE PIPING USING FITTINGS MANUFACTURED TO ANSI STANDARDS. 30. MAKE GOOD ALL SURFACES AFTER COMPLETION OF WORK. This drawing is not to be used for
GENERAL CONTRACT SPECIFICATIONS. COPY IN PDF FORMAT CONTRACTOR RED LINES AND O&M MANUAL. MANUALS SHALL 4.4. CONNECT TO EQUIPMENT IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTION UNLESS construction unless it is countersigned
by the Project Architect
INCLUDE SHOP DRAWINGS OF ALL NEW EQUIPMENT, TEST AND BALANCING REPORTS, OTHERWISE INDICATED. 31. REMOVE AND DISPOSE IMMEDIATELY OF ALL DEBRIS PRODUCED BY THE SCOPE OF
3. WARRANTY COMMISSIONING REPORTS, WARRANTIES, AND OPERATION, MAINTENANCE 4.5. SLOPE PIPING DOWN IN DIRECTION OF FLOW TO LOW POINTS. WORK.
3.1. WARRANT ALL LABOUR AND MATERIALS INCLUDED IN THIS CONTRACT FOR A PROCEDURES AND AS BUILT DRAWINGS. 4.6. INSTALL DRIP POINTS: Issued For (YYMMDD)
PERIOD OF TWO YEARS FROM DATE OF FINAL ACCEPTANCE. ASSUME FULL 4.6.1. AT LOW POINTS IN PIPING SYSTEM. 32. ALL NEW EQUIPMENT SHALL UNDERGO SHOP DRAWING REVIEW BY ENGINEER. TENDER 2020.06.01
RESPONSIBILITY FOR LAYOUT OF ALL WORK AND FOR ANY DAMAGE CAUSED TO 18. TESTING, ADJUSTING AND BALANCING (T.A.B.) 4.6.2. AT EACH CONNECTION TO EQUIPMENT.
OWNER OR OTHERS BY IMPROPER CARRYING OUT OF THE WORK. 18.1. INCLUDE ALL TESTING, ADJUSTING AND BALANCING FOR AIR SYSTEMS INCLUDING, 4.7. USE ECCENTRIC REDUCERS AT PIPE SIZE CHANGE INSTALLED TO PROVIDE POSITIVE 33. PROVIDE TWO (2) SETS OF CLOSEOUT DOCUMENTS (+ SOFT COPY OF THE SAME) I.E.
BUT NOT LIMITED TO, THE FOLLOWING: DRAINAGE. MANUAL, WARRANTY, STARTUP, BALANCING AND DUCT CLEANING REPORTS, SHOP
4. DRAWINGS 19.1.1. NEW EXHAUST FAN UNITS 4.8. PROVIDE CLEARANCE FOR ACCESS AND FOR MAINTENANCE. DRAWINGS ETC. AFTER COMPLETION OF THE WORK AND BEFORE CLOSEOUT MEETING.
4.1. DRAWINGS SHOW GENERAL INTENT OF THE WORK AND PROPOSED ROUTING 19.1.2. RELOCATED BOILER (HB-3) C/W CIRCULATION PUMP (P-18) IN 125 RR NG-02 4.9. REAM PIPES, CLEAN SCALE AND DIRT, INSIDE AND OUT.
ONLY. 19.1.3. BOILER BREECHING 4.10. PROVIDE PRESSURE REGULATORS REQUIRED FOR RELOCATION OF GAS RELIEF VENTS. 34. CONTRACTOR TO CONFIRM ALL VOLTAGES AND GAS PRESSURES AS PER TSSA AND
4.2. DO NOT SCALE DRAWINGS. CONTRACTOR SHALL CONFIRM ALL DIMENSIONS BY 18.2. INCLUDE REPORT IN THE OPERATION AND MAINTENANCE MANUALS 4.11. INSTALL PIPING TO MINIMIZE PIPE DISMANTLING FOR EQUIPMENT REMOVAL. GAS CODE.
FIELD MEASURE BEFORE PROCEEDING WITH THE WORK. 18.3. NOTIFY ENGINEER OF ANY DISCREPANCIES GREATER THAN ±5% OF DESIGN VALUES 4.12. INSTALL VALVES WITH STEMS UPRIGHT OR HORIZONTAL UNLESS OTHERWISE APPROVED
4.3. CONTRACTORS SHALL BE RESPONSIBLE FOR IDENTIFYING POSSIBLE PRIOR OF SUBMISSION OF REPORT. BY ENGINEER.
INTERFERENCES AND INFORMING THE ENGINEER. 18.4. BALANCING SHALL BE PERFORMED BY AN AABC OR NEBB CERTIFIED BALANCER 4.13. INSTALL VALVES AT BRANCH TAKE-OFFS TO ISOLATE EACH PIECE OF EQUIPMENT AND AS
INDICATED.
5. SITE CONDITIONS 19. REMOVE ALL ABANDONED PIPES, HANGERS, INSERTS, CONDUITS, DUCTS AND SERVICES. FIRESTOP
5.1. EXAMINE SITE CONDITIONS TO ENSURE THAT WORK CAN BE SATISFACTORILY AND SEAL ALL AFFECTED AREAS. 5. TESTING
CARRIED OUT AS SHOWN. IF SITE EXAMINATION REVEALS ANY DIFFICULTIES THAT 5.1. TEST SYSTEM IN ACCORDANCE WITH CAN/CGA B149.1 AND REQUIREMENTS OF
WILL PREVENT THE WORK FROM BEING CARRIED OUT AS DESIGNED THESE MUST 20. SEAL AND FIRESTOP ALL WALL, FLOOR AND ROOF PENETRATIONS THROUGH FIRE RATED AUTHORITIES HAVING JURISDICTION.
BE INDICATED IN THE TENDER PRICE, AND BROUGHT TO THE ATTENTION OF THE ASSEMBLIES. 5.2. PURGE AFTER PRESSURE TEST IN ACCORDANCE WITH CAN/CGA B149.1
ENGINEER. 21. ALL NEW EQUIPMENT CONTROL PANELS MUST BE OPEN PROTOCOL TYPE BACNET CERTIFIED.
5.2. THE CONTRACTOR SHALL INFORM THE ENGINEER IN WRITING OF ANY ADDITIONAL
DIFFICULTIES, INTERFERENCES AND SITE CONSTRAINTS THAT MAY BE IDENTIFIED 22. CO-ORDINATE ALL DIMENSIONS WITH EQUIPMENT SHOP DRAWINGS. PERMIT AND FEES:
DURING THE CONSTRUCTION PERIOD.

Date
5.3. ALL NOISY WORK SHALL BE PERFORMED AFTER NORMAL BUSINESS HOURS: 23. THOROUGHLY INSPECT EXISTING STRUCTURE AND CHECK SITE CONDITIONS WITH CONDITION 1. THE CONTRACTOR SHALL APPLY FOR AND OBTAIN IN ITS OWN NAME, PERMITS, LICENSES,
BETWEEN 5PM AND 8AM, MONDAY THROUGH FRIDAY; AND ON WEEKENDS. SHOWN ON CONTRACT DRAWINGS BEFORE PROCEEDING WITH WORK. MAKE ADJUSTMENTS TO APPROVALS AND SHALL PAY FEES AND GIVE NOTICES NECESSARY PRIOR TO COMMENCING WORK
5.4. ALL NOISY WORK REQUIRED ON COTTAGES (1-6) SHALL BE PERFORMED DURING WORK TO SUIT EXISTING CONDITION AND IN CONFORMANCE WITH DESIGN INTENT. REPORT ANY AND INCIDENTAL TO THE DUE AND LAWFUL PERFORMANCE OF THE WORK, IN ACCORDANCE WITH THE
NORMAL BUSINESS HOURS: BETWEEN 8AM AND 7PM, MONDAY THROUGH FRIDAY. DISCREPANCIES TO THE ENGINEER. SPECIFICATIONS.
AFTER HOURS CONSTRUCTION SHALL NOT OCCUR.
5.5. CONTRACTORS SHALL COORDINATE SITE ACCESS, SECURITY ESCORT AND 24. MATERIALS AND WORK WHICH FAILS TO MEET SPECIFIED REQUIREMENTS WILL BE REJECTED BY THE 2. THE CONTRACTOR SHALL ENSURE THAT THE JURISDICTIONAL AUTHORITIES ARE NOTIFIED OF THE
DELIVERIES WITH BASE BUILDING 48 HRS IN ADVANCE. ENGINEER WHENEVER FOUND AT ANY TIME PRIOR TO FINAL ACCEPTANCE AND REGARDLESS OF DATE FOR THE COMMENCEMENT OF THE WORK AND THE DATES OF ACTIVITY OF THE WORK FOR WHICH
PREVIOUS INSPECTIONS. WHEN REJECTED, DEFECTIVE MATERIALS OR WORK SHALL BE PROMPTLY MUNICIPAL INSPECTORS ARE REQUIRED TO BE PRESENT. THE CONTRACTOR SHALL SEND A COPY OF
6. CLEANING REMOVED, REPLACED OR REPAIRED TO THE SATISFACTION OF THE ENGINEER AT NO EXPENSE TO ALL CORRESPONDENCES TO THE ENGINEER.

Revision Schedule
6.1. CLEAN PREMISES DAILY AT THE END OF EACH WORK DAY. THE OWNER
6.2. DO NOT ACCUMULATE EQUIPMENT, TOOLS, DEBRIS AND WASTE MATERIALS ON 3. THE CONTRACTOR SHALL BE RESPONSIBLE SHOULD FAILURE OCCUR.
SITE. REMOVE FROM SITE DAILY. HVAC:

Description
6.3. COMPLETELY REMOVE ALL DEBRIS AND RUBBISH FROM SPACE ONCE WORK IS
COMPLETE. 1. BALANCING GENERAL SCOPE OF WORK:
6.4. ALL MATERIALS TO BE DISPOSED OF CONSTRUCTION SITE IN ACCORDANCE WITH 1.1. SHEET METAL CONTRACTOR SHALL EMPLOY THE SERVICES OF A LICENSED
ALL APPLICABLE REGULATIONS. INDEPENDENT BALANCING COMPANY TO BALANCE THE AIR SYSTEMS TO ACHIEVE 1. FURNISH ALL LABOUR, MATERIALS, EQUIPMENT, TOOLS AND SUPPORTS AS WELL AS SUPERVISION TO
THE AIRFLOW SHOWN. THE BALANCING COMPANY SHALL SUBMIT A COMPLETE PROVIDE A COMPLETE INSTALLATION, TESTED AND IN WORKING ORDER, AS SHOWN ON THE DRAWINGS.
7. EXISTING EQUIPMENT AND SYSTEMS REPORT. ACCEPTANCE OF BALANCING AND REPORT WILL BE SUBJECT TO ON SITE
7.1. DISCONNECT, RECONNECT OR RELOCATE EXISTING EQUIPMENT OR SERVICES MEASUREMENT AND/OR VERIFICATION OF THE REPORT BY THE MECHANICAL 2. THE CONTRACTOR SHALL PERFORM THE WORK STIPULATED IN THE CONTRACT AND ANY OR ALL CONTRACT
WHERE SHOWN OR AS REQUIRED TO PERMIT NEW WORK TO BE INSTALLED ENGINEER. CHANGES AND CHANGE DIRECTIVES, AND SHALL FURNISH, UNLESS OTHERWISE PROVIDED IN THE
WITHOUT INTERFERENCES. ENSURE THAT REQUIRED SERVICES ARE MAINTAINED. CONTRACT, EVERYTHING NECESSARY FOR THE PROPER PERFORMANCE AND COMPLETION OF THE WORK.
7.2. COORDINATE WITH THE OWNER BEFORE INTERRUPTING ANY ESSENTIAL 2. VIBRATION ISOLATION
SERVICES. 2.1. PROVIDE AND INSTALL NEOPRENE HANGERS FOR CEILING SUSPENDED EQUIPMENT, 3. ALL WORK SHALL BE FULLY TESTED, COMMISSIONED AND IN GOOD WORKING ORDER AT TIME OF HAND-
7.3. ROUTING OF NEW SERVICES MAY BE ADJUSTED TO ACCOMMODATE EXISTING DUCTWORK AND ACCESSORIES. OVER TO OWNER.
SERVICES AND CONDITIONS PROVIDED THAT THE INTENT OF THE DRAWINGS IS

No.
MET AND THE ORIGINAL STANDARDS ARE MAINTAINED. 3. LOCAL CONTROLLER 4. MAKE GOOD ANY DAMAGES TO EXISTING EQUIPMENT AND/OR SYSTEM(S). COORDINATE WORK AND
7.4. PROVIDE DRAWINGS OF PROPOSED REVISIONS TO ENGINEER FOR APPROVAL 3.1 COORDINATE INSTALLATION WITH ELECTRICAL DRAWINGS AND MANUFACTURER’S WORKING HOURS WITH THE OWNER AND OTHER TRADES TO MINIMIZE DISRUPTION.
BEFORE BEGINNING ANY WORK. INCORPORATE ALL CHANGES IN AS BUILT RECOMMENDATIONS.
DRAWINGS. 5. NOTIFY AND CO-ORDINATE WITH OWNER, CONSULTANT, AND RESIDENT, WHETHER WORK WILL EFFECT
7.5. COORDINATE ALL ROUTING CHANGES WITH OTHER TRADES THAT MAY BE

MECHANICAL GENERAL NOTES

4. BREECHING AND CHIMNEY FOR BOILER OPERATION OF THE BUILDING.
AFFECTED. 4.4. EACH PART OF THE EQUIPMENT SHALL INCLUDE A FACTORY APPLIED STICKER OR
7.6. ENGINEER TO BE ADVISED PRIOR TO CHANGES WHERE CHANGES COULD BE MARKING INDICATING PRODUCT TYPE. 1. CONTRACTOR TO MAKE ARRANGEMENTS WITH THE OWNER REGARDING GARBAGE RELOCATION DURING
SIGNIFICANT. 4.5. AN RVT OR SILICONE TYPE SEAL WILL NOT BE ACCEPTABLE. THE DURATION OF THE WORK. CONTRACTOR WILL PAY ALL COSTS ASSOCIATED WITH INCREASED PROJECT
7.7. THE CONTRACTOR IS TO TAKE EXTRA CARE DURING THIS INSTALLATION NOT TO 4.6. ALLOW UNOBSTRUCTED DIFFERENTIAL THERMAL EXPANSION OF THE INNER AND OPERATION PHASING TO ENSURE THERE IS NO DISRUPTION OF GARBAGE REMOVAL OPERATIONS.
DISTURB THE OPERATIONS OF THE COMPLEX. IT IS CRITICAL THAT THERE WILL BE OUTER WALLS.
NO UNSCHEDULED SHUTDOWNS OR INTERRUPTIONS OF ANY OPERATIONS. 4.7. VENT SHALL BE CONSTRUCTED OF AN INNER AND OUTER WALL WITH A 1” ANNULAR 2. CONTRACTOR TO ENSURE THERE WILL BE NO OBSTRUCTIONS TO THE FIRE ROUTE DURING THE
7.8. ALL ASSOCIATED COSTS OF SUCH WILL BE PASSED TO THE CONTRACTOR. INSULATED AIR SPACE. CONSTRUCTION WORK.
4.8. INSTALL VENT SYSTEM WITH ½” VERTICAL DROP FOR EVERY FOOT OF HORIZONTAL
8. OPEN FLAMES ABD WELDING BREECHING WITH ALL LONGITUDINAL SEAMS ON TOP. 3. ALL ACCESS TO THE UNITS WILL BE FROM THE EXTERIOR ONLY. NO INTERIOR ACCESS WILL BE PROVIDED.
8.1. NO OPEN FLAMES OR WELDING IS PERMITTED WITHIN THE BUILDING WITHOUT 4.9. ALL PARTS EXPOSED TO THE WEATHER SHALL BE PROTECTED BY ONE COAT OF
WRITTEN PERMISSION BY THE OWNER AND/OR ENGINEER. CORROSION AND HEAT RESISTANT BASE PRIMER AND ONE COAT OF HEAT RESISTANT 4. THERE IS LIMITED STORAGE ON SITE, ALL WASTE MATERIALS TO BE REMOVED FROM THE SITE DAILY.
8.2. HOT WORK PERMIT MUST BE VISIBLE AT ALL TIMES. PAINT.
8.3. ADEQUATE NUMBER OF FIRE EXTINGUISHERS MUST BE PROVIDED DURING THE 4.10. ALL ACCESSORIES (EXIT CONE, CONNECTORS AND DRAIN FITTINGS) WITH DIRECT OR 5. PROVIDE ALL WORK AS INDICATED IN DRAWINGS AND SPECIFICATIONS. INCLUDE ALL MECHANICAL,
OPEN FLAME PROCESS. INDIRECT CONTACT WITH CONDENSATE SHALL BE PROVIDED IN AL29-4C. CONTROLS, AND ELECTRICAL WORK REQUIRED FOR A FULLY FUNCTIONAL SYSTEM.
4.11. ALL ACCESSORIES (SUPPORTS, ROOF OR WALL PENETRATIONS) NOT IN CONTACT
9. MATERIALS WITH CONDENSATE SHALL BE PROVIDED IN 304 STAINLESS STEEL. 6. CONTRACTOR TO EXAMINE SITE PRIOR TO THE COMMENCEMENT OF ANY WORK.
9.1. USE ONLY NEW CSA AND ULC CERTIFIED EQUIPMENT AND MATERIALS UNLESS 4.12. BREECHING SUPPORT DISTANCES SHALL BE AS PE MANUFACTURER
OTHERWISE INDICATED. RECOMMENDATIONS. 7. COORDINATE ALL SITE ACCESS, DELIVERY, AND EQUIPMENT SHUT DOWN WITH OWNER.
9.2. ONLY FIRST CLASS WORKMANSHIP WILL BE ACCEPTED WITH RESPECT TO 4.13. ROOF PENETRATION PIECES SHALL BE ULC LISTED AND PROVIDED BY THE VENT
STANDARD PRACTICES, SAFETY, ACCESSIBILITY, DURABILITY AND NEATNESS OF MANUFACTURER. 13. PROVIDE CRANE SERVICES WITH CITY PERMIT AND POLICE SERVICES IF/AS REQUIRED. COORDINATION
INSTALLATION WORK. 4.14. PROVIDE ROOF CURB/HOUSING FOR EACH VENT/ROOF PENETRATION. AND SAFETY PLAN AS REQUIRED PRIOR TO LIFTING NEW EQUIPMENT ON ROOF.
4.15. WHERE EXPOSED TO WEATHER, THE CASING JOINTS SHALL BE SEALED TO PREVENT
10. SHOP DRAWINGS RAINWATER FROM ENTERING THE SPACE BETWEEN INNER AND OUTER WALLS. 14. PROVIDE AND INSTALL TWO NEW EQUIPMENT, SUPPLY AND RETURN AIR DUCTWORK, AND
10.1. SUBMIT 4 COPIES OF SHOP DRAWINGS, UNLESS OTHERWISE INDICATED, FOR 4.16. VENT SHALL TERMINATE IN ACCORDANCE WITH INSTALLATION INSTRUCTIONS AND CONTROLS. CONTRACTOR TO REPAIR ROOF AFTER WORK IS COMPLETED.
ENGINEER’S REVIEW. LOCAL CODES.
10.2. SUBMIT SHOP DRAWINGS AND PRODUCT DATA FOR ENGINEER’S REVIEW 4.17. STACKS TERMINATING ABOVE A ROOF MUST TERMINATE AS REQUIRED BY CSA B149.1 15. ROVIDE PROFESSIONAL CLEANING AND SANITATION OF ALL EXISTING SUPPLY AIR DUCTS AND GRILLES
COVERING ALL RELEVANT DETAILS, DIMENSIONS AND PERFORMANCE. CODE. SERVING EQUIPMENT. PROVIDE DUCT CLEANING REPORT, PHOTOS OF DUCTS BEFORE AND AFTER
10.3. SHOP DRAWINGS MUST BE REVIEWED, STAMPED AND SIGNED BY THE 4.18. TOTAL STACK HEIGHT SHALL BE 18” HIGH MAXIMUM. CLEANING FOR ENGINEERS REVIEW AND SIGN OFF.
CONTRACTOR AND THE GENERAL CONTRACTOR PRIOR TO SUBMITTING TO 4.19. PROVIDE ENGINEERED SHOP DRAWINGS OF SYSTEM FOR APPROVAL.
CONSULTANT/ENGINEER FOR REVIEW. 4.20. INSTALLATION SHALL BE IN COMPLIANCE WITH MANUFACTURER’S 16. CONTRACTOR TO BE RESPONSIBLE FOR RIGGING, HOISTING, AND ANY ASSEMBLY OF RTUS.

John R. Park Homestead Heritage Centre

RECOMMENDATIONS, CSA B149 AND ALL APPLICABLE CODES.
11. CUTTING, PATCHING AND PAINTING REQUIREMENTS 17. EXISTING SUPPLY AND RETURN DUCTWORK ON THE ROOF TO BE REMOVED AND NEW DUCT AND THERMAL
11.1. PROVIDE CUTTING, PATCHING AND PAINTING FOR ALL OPENINGS. USE QUALIFIED 5. CONTROLS INSULATION TO BE PROVIDED.

915 County Road 50, Essex, Ontario N0R 1G0

TRADES FOR THIS WORK. RESTORE FINISHES TO MATCH EXISTING 5.1. CONTROLS CONTRACTOR SHALL PROVIDE A COMPLETE STAND-ALONE (LOCAL) CONTROL
SURROUNDINGS. SYSTEM; INCLUDING CONTROLLER, PRESSURE SENSORS, 120/24V TRANSFORMERS, 18. PROVIDE AND INSTALL THERMAL INSULATION AS INDICATED ON THE DRAWINGS AND SPECIFICATIONS.
11.2. SUPPLY AND INSTALL APPROVED FIRESTOPS AS REQUIRED TO MAINTAIN FIRE CHIMNEY PROBES AND WIRING/TUBING.
RATING. 5.2. PROVIDE ASSISTANCE TO GENERAL/MECHANICAL CONTRACTOR, COORDINATE SYSTEM TO 19. PROVIDE AND INSTALL FLEXIBLE DUCT CONNECTIONS BETWEEN ROOF AND BUILDING INTERIOR.
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

11.3. PIPING AND VENTS THROUGH WALL AND ROOF SHALL BE BY THE MECHANICAL ENSURE AN ACCURATE OPERATING CONTROL SYSTEM IS ACHIEVED.
DIVISION CONTRACTOR, INCLUDING ALL PATCHING. 5.3. B.A.S. CONTRACTOR SHALL EXTEND BAS GRAPHICS TO INCLUDE FOR SYSTEM MONITORING 20. CONTRACTOR (FROM THE APPROVED VENDORS LIST) SHALL ADD NEW DUCT SMOKE DETECTORS FOR
(OPERATIONAL STATUS) AND HIGH LEVEL ALARMS (FAN, DUCTWORK PRESSURE, AND SUPPLY AIR DUCTWORK AND INTEGRATE ON EXISTING FIRE ALARM PANEL CONTRACTOR TO ADD FIRE
12. CORING REQUIREMENTS OVERALL SYSTEM). ALARM SHUTDOWN TO THE NEW EQUIPMENT. ADD NEW POINTS TO THE EXISTING FIRE CONTROL PANEL. IF
12.1. FOR ALL CORING LESS THEN 3” DIA. CONTRACTOR SHALL BE RESPONSIBLE FOR 5.4. BASE BUILDING CONTROLS VENDOR=NICHOLAS DUMOULIN – PROJECT MANAGER NO CONNECTIONS EXIST, PROVIDE ALL NECESSARY CONNECTIONS FOR CODE COMPLIANCE.
SCANNING AREA PRIOR TO CORING THROUGH FLOORS/CEILINGS. 416-422-0531 EXT. 2406
12.2. FOR ALL CORING GREATER THEN 3” DIA. CONTRACTOR SHALL BE RESPONSIBLE 21. CONTROLS CONTRACTOR TO PROVIDE AND INSTALL NECESSARY RTU CONTROL WORK & SAFETY DEVICES.
FOR X-RAYING AREA PRIOR TO CORING THROUGH FLOORS/CEILINGS. GAS PIPING:
22. PROVIDE PROFESSIONAL CLEANING AND SANITATION OF ALL EXISTING SUPPLY AIR DUCT AND GRILLES
13. PENETRATIONS THROUGH FLOORS AND WALLS 1. PIPE SERVING MAU-1 AND MAU-2. PROVIDE DUCT CLEANING REPORT, PHOTOS OF DUCTS BEFORE AND AFTER
13.1. UNLESS OTHERWISE SPECIFIED ON DRAWINGS, GLASS FIBRE FIRE RETARDANT 1.1. STEEL PIPE: TO ASTM A53, GRADE B, SCHEDULE 40, SEAMLESS AS FOLLOWS: CLEANING FOR ENGINEERS REVIEW AND SIGN OFF.
INSULATION AND FIRESTOP CAULKING SHALL BE PACKED AROUND PIPE 1.1.1. NPS ½ TO 2, SCREWED.
OPENINGS IN FLOORS AND WALLS AT THE TIME OF PIPE INSTALLATION. FIRESTOP 1.1.2. NPS 2 ½ AND OVER, PLAIN END. 23. THE NEW RTUS SHALL COME WITH AN OPEN UNIT CONTROLLER ALLOWING INTEGRATION WITH EXISTING
CAULKING SHALL BE “3M FIRE BARRIER” FIRETEMP CAULK OR EQUIVALENT. 1.1.3. COPPER TUBE: TO ASTM B75M BUILDING AUTOMATION SYSTEM (B.A.S). EXTEND CONTROL WIRING FROM UNIT TO BAS. CONTRACTOR TO
13.2. APPLY FIRESTOP SYSTEMS IN ACCORDANCE WITH 3,’S INSTRUCTIONS. ALL 1.2. JOINING MATERIAL PROVIDE NECESSARY CONTROL DEVICES, PANELS AND B.A.S. PROGRAMMING FOR A FULLY
SYSTEMS SHALL MEET CSA F-SYSTEM RATINGS FOR THE PARTICULAR FIRE 1.2.1. SCREWED FITTINGS: PULVERIZED LEAD PASTE. FUNCTIONAL SYSTEM. CONTRACTOR TO ADD ADDITIONAL POINTS AS INDICATED WHILE MAINTAINING
RATING OF THE PENETRATED SURFACE. 1.2.2. WELDED FITTINGS: TO CSA W47.1. EXISTING POINTS AND ALARMS.
13.3. FIRESTOPPING CONTRACTOR MUST BE A LICENSED 3M CERTIFIED INSTALLER. 1.2.3. FLANGE GASKETS: NONMETALLIC FLAT.
13.4. MATERIALS SHALL BE ASBESTOS-FREE ELASTOMERIC MATERIALS, TESTED, 1.2.4. SOLDERED: TO ASTM B32, TIN ANTIMONY 5/5

ERCA
LISTED AND LABELLED BY ULC IN ACCORDANCE WITH CAN 4-S115-M85, AND
CAN/ULC=S101-M FOR INSTALLATION IN ULC DESIGNATED FIRE STOPPING AND
SMOKE SEAL SYSTEMS, TO PROVIDE A POSITIVE FIRE, WATER AND SMOKE SEAL
AND A FIRE RESISTANCE RATING (FLAME, HOSE STREAM AND TEMPERATURE) NOT
LESS THAN THE FIRE RATING FOR SURROUNDING CONSTRUCTION. MATERIALS
SHALL BE COMPATIBLE WITH ABUTTING DISSIMILAR MATERIAL AND FINISHES.
Drawn By Checked By
ai ai
6/1/2020 9:20:12 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

1. ALL PLUMBING, DRAINAGE AND VENT PIPING SHALL CONFORM TO ONT. REG. 332/12
BUILDING CODE, PART 7.

2. MECHANICAL DRAWINGS SHALL BE READ IN CONJUNCTION WITH ARCHITECTURAL

DRAWINGS AND SPECIFICATIONS.

3. ALL MATERIAL WITHIN THE CEILING SPACE USED AS RETURN AIR PLENUM SHALL HAVE A
MAXIMUM FLAME SPREAD RATING OF 25 AND A MAXIMUM SMOKE DEVELOPED
CLASSIFICATION OF 50.
180 Eugenie Street West
4. DO NOT COVER ANY STORM, SANITARY, VENT AND WATER PIPING PRIOR TO TESTING. Windsor, ON N8X 2X6
INSPECTOR SHALL WITNESS THE TEST. 519.258.1390

5. ALL PLUMBING AND DRAINAGE PIPES PENETRATING FIRE SEPARATIONS SHALL BE FIRE
STOPPED.

6. POTABLE WATER SYSTEM SHALL BE DESIGNED, CONSTRUCTED AND INSTALLED TO

CONFORM TO GOOD ENGINEERING PRACTICE APPROPRIATE TO THE CIRCUMSTANCES,
SUCH AS THAT DESCRIBED IN THE ASHRAE HANDBOOKS AND ASPE DATA BOOKS AND
ARTICLE 7.6.3.4. OF THE BUILDING CODE.
VESTIBULE This drawing is not to be used for
construction unless it is countersigned
101 REMARKS by the Project Architect

1. THE NEW BUILDING SANITARY DRAIN SHOWN ON THIS DRAWING IS FOR DESIGN INTENT Issued For (YYMMDD)
PURPOSES ONLY. PROPOSED SANITARY DRAINAGE LINE SHALL BE SUPPLIED AND TENDER 2020.06.01
INSTALLED BY GC AND COORDINATED WITH LL.CONTRACTO. REPORT TO THE ENGINEER
LAV-1 FOR ANY MAJOR DISCREPANCIES OR CONCERNS THAT CONFLICTS WITH THE DESIGN.

2. PATCH AND SEAL WITH FIRE STOP MATERIALS AT ALL PIPE PENETRATION THROUGH THE
WELCOME CENTRE FLOORS/WALLS THAT ARE DEEMED FIRE RATED. COORDINATE WITH ARCHITECT.
WC-1 WC-1 WC-1 WC-2
3"ø

3"ø
3"ø

102 4. PROPOSED SANITARY LINE DISTRIBUTION SHALL BE COORDINATED WITH LANDLORD.

FD 5. PROVIDE PROPER PLUMBING VENTING AS PER ONTARIO PLUMBING CODE. (TYP.)
4"ø
OPEN AREA
3"ø

WOMEN W/R
CO
113
CO 4" SANITARY DRAIN @ 1% SLOPE
2"ø

4"ø
LAV-1

4" SANITARY DRAIN @ 2% SLOPE

COMMON HALLWAY

Date
112

LAV-2
OFFICE
104
MEN W/R
2"ø

Revision Schedule
111
3"ø

Description
3"ø
4"ø
3"ø

UNIVERSAL WR
4"ø

WC-2 WC-1
UR UR
105
FD
LAV-1 WC-2

.
S-1
2"ø

CORRIDOR WF
3"ø

3"ø
1 1/2"ø

3" SAN. DRAIN CO 103 ? FD ?

SERVERY

No.
FROM MECHANICAL FD
3"ø 4"ø ? ?
ROOM DOWN 109
CO
3"ø

3"ø
MOP

ZONE-02

4" SAN DRAIN

TO SEPTIC TANK
REFER SITE
DRAWING FOR

SANITARY & STORM

EXACT LOCATION
OF SEPTIC TANK

CREATIVE COMMONS
108
OPEN AREA

John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

N N
FIRST FLOOR - SANITARY AND STORM - NEW WORK MEZZANINE - SANITARY AND STORM - NEW
SCALE: 1 : 75 SCALE: 1 : 75
PLUMBING FIXTURE SCHEDULE
DRAIN VENT HW CW
MARK QTY MANUFACTURER DESCRIPTION
Inch mm Inch mm Inch mm Inch mm
WC-1 4 AMERICAN STANDARD OR EQUIVALENT FLOOR MOUNTED TANK TOILET 3.0 75 2.0 50 - - 0.75 20

WC-2 3 AMERICAN STANDARD OR EQUIVALENT BARRIER FREE TANK TOILET 3.0 75 2.0 50 - - 0.75 20

LAV-1 6 AMERICAN STANDARD OR EQUIVALENT SS COUNTERTOP SINK 1.50 37 2.0 50 0.5 12.5 0.5 12.5

ERCA
LAV-2 1 AMERICAN STANDARD OR EQUIVALENT BARRIER FREE SINK 1.50 37 2.0 50 0.5 12.5 0.5 12.5

S-1 1 KINDRED OR EQUIVALENT SS KITCHEN SINGLE SINK 1.50 37.5 1.5 37 0.5 12.5 0.5 12.5

WF 1 ELKAY OR EQUIVALENT WATER FOUNTAIN 1.50 37.5 1.5 37 - - 0.5 12.5

Drawn By Checked By

MOP 1 MOP BASIN SINK 3.0 75 - - - - ai ai

6/1/2020 9:20:15 AM

SWAN OR EQUIVALENT 2.0 50

Project No
UR 2 AMERICAN STANDARD OR EQUIVALENT URINAL 2.0 50 1.5 37 - - 0.75 20 2020
THIS LINE IS 4" LONG
Sheet No

1. ALL PLUMBING, DRAINAGE AND VENT PIPING SHALL CONFORM TO ONT. REG. 332/12
BUILDING CODE, PART 7.

2. MECHANICAL DRAWINGS SHALL BE READ IN CONJUNCTION WITH ARCHITECTURAL

DRAWINGS AND SPECIFICATIONS.

3. ALL MATERIAL WITHIN THE CEILING SPACE USED AS RETURN AIR PLENUM SHALL HAVE A
MAXIMUM FLAME SPREAD RATING OF 25 AND A MAXIMUM SMOKE DEVELOPED
CLASSIFICATION OF 50.
180 Eugenie Street West
Windsor, ON N8X 2X6
4. DO NOT COVER ANY STORM, SANITARY, VENT AND WATER PIPING PRIOR TO TESTING. 519.258.1390
INSPECTOR SHALL WITNESS THE TEST.

5. ALL PLUMBING AND DRAINAGE PIPES PENETRATING FIRE SEPARATIONS SHALL BE FIRE
STOPPED.

6. POTABLE WATER SYSTEM SHALL BE DESIGNED, CONSTRUCTED AND INSTALLED TO

CONFORM TO GOOD ENGINEERING PRACTICE APPROPRIATE TO THE CIRCUMSTANCES,
SUCH AS THAT DESCRIBED IN THE ASHRAE HANDBOOKS AND ASPE DATA BOOKS AND
VESTIBULE ARTICLE 7.6.3.4. OF THE BUILDING CODE.
This drawing is not to be used for
101 construction unless it is countersigned
by the Project Architect
REMARKS
Issued For (YYMMDD)
1. THE NEW BUILDING SANITARY DRAIN SHOWN ON THIS DRAWING IS FOR DESIGN INTENT
TENDER 2020.06.01
PURPOSES ONLY. PROPOSED SANITARY DRAINAGE LINE SHALL BE SUPPLIED AND
INSTALLED BY GC AND COORDINATED WITH LL.CONTRACTO. REPORT TO THE ENGINEER
FOR ANY MAJOR DISCREPANCIES OR CONCERNS THAT CONFLICTS WITH THE DESIGN.
WC-1 WC-1 WC-1 WC-2 2. PATCH AND SEAL WITH FIRE STOP MATERIALS AT ALL PIPE PENETRATION THROUGH THE
WELCOME CENTRE
OPEN AREA FLOORS/WALLS THAT ARE DEEMED FIRE RATED. COORDINATE WITH ARCHITECT.
1 1/4"ø

102 4. PROPOSED SANITARY LINE DISTRIBUTION SHALL BE COORDINATED WITH LANDLORD.

WOMEN W/R ATTIC AREA
5. PROVIDE PROPER PLUMBING VENTING AS PER ONTARIO PLUMBING CODE. (TYP.)
113 118

LAV-1
1"ø

COMMON HALLWAY

Date
112
1 1/2" POTABLE COLD
WATER OUTLET
OFFICE
104 1 1/2" POTABLE COLD
WATER INLET
LAV-1

Revision Schedule
MEN W/R CORRIDOR
111 103

Description
UNIVERSAL WR
WC-2 WC-1 105 CONNECT 1-1/2"Ø TO NEAREST MEZZ. (OPEN)
UR UR 1/2" DCW AIR GAP
UP TO SERVE SUPPLY LINE OF SUFFICIENT 115
WF SIZE.

INSTALL WITH TOP BACKFLOW

LAV-2 CONTRACTOR TO VERIFY
WC-2 EXACT TIE-IN LOCATION ON

1240 @ 48"AFF
. CLOSET
WF SITE.
S-1 TANKLESS
110
3/4"ø

M WATER
1 1/4"ø

3/4"ø

PREVENTER
1 1/2"ø HEATERS
TO BE SUPPLIED &
SERVERY INSTALLED

No.
BY MECHANICAL
1/2"ø

109 STORAGE
CONTRACTOR MEZZ. BRIDGE
107 MOP
116

3/4"ø DRAIN TO FUNNEL FLOOR

1 1/2" DCW PIPE UP TO SUPPLY & INSTALL NEW WATER WH-2 WH-1 DRAIN BELOW
WH-1,2 AND 1" DHW TANKLESS WATER DCW & CHW TO RUN METER c/w ACCESSIBLE REMOTE
HEATER AT MEZZANINE IN JOIST SPACE ABOVE READOUT AND BACK FLOW
DOOR 3/4" DHW FROM
FLOOR PREVENTOR ALONG THE WALL
FIRST FLOOR
AS REQUIRED BY LOCAL 1 1/2" DCW FROM
DOWN TO SERVE
MUNICIPALITY AND OHJ. FIRST FLOOR
PLUMBING FIXTURES BACKFLOW PREVENTOR
WATER METER SHALL BE 1" DHW PIPE
IN SERVERY
ACCESSIBLE AND SHALL DOWN TO SERVE
CONFORM DESIGN GUIDELINES. PLUMBING FIXTURES

DOMESTIC WATER
ON FIRST FLOOR
DOUBLE CHECK VALVE PLUMBING NOTES:
ASSEMBLY BACK FLOW
CREATIVE COMMONS PREVENTER ( ZURN WILKINS 1. COORDINATE VENT STACK THROUGH ROOF ONSITE.
108 MODEL# 350XL OR EQUAL) TO BE
INSTALLED IN VERTICAL
OPEN AREA 2. SINK CONNECTIONS TO BE 1/2"⌀ @ WALL.
ORIENTATION. ENSURE
SUFFICIENT ACCESS AS
3. PATCH & REPAIR ALL FLOORS AND FINNISH TO MATCH REQUIRING
RECOMMENDED BY
MANUFACTURER.
4. WATER SERVICE SHALL BE EQUIPPED WITH AN RP-TYPE BACKFLOW PREVENTER IMMEDIATLY AFTER
WATER SERVICE ENTERS THE BUILDING

5. INSTALL PRESSURE AND TEMPERATURE RELIF VALVES ON ALL WATER HEATERS INSTALLED IN PLUMBING
SYSTEM, PER 7.6.1.12 OF OBC

6. MINIMUM 1" INSULATION FOR DOMESTIC WATER PIPING AND SHALL COMPLY WITH TABLE 6.8.3A OF
ASHRAE 90.1 2013 EDITION

John R. Park Homestead Heritage Centre

7. DOMESTIC WATER LINES SHALL BE TYPE L. COOPER TO ASTM B88-03

8. FIRESTOP ALL PENETRATIONS OF RATED FIRE SEPARATIONS PER 3.1.9.1 OF OBC. REFER TO

915 County Road 50, Essex, Ontario N0R 1G0

ARCHITECTURAL DRAWINGS FOR LOCATIONS AND RATINGS

9. COMBUSTIBLE PIPE MATERIALS SHALL NOT BE LOCATED WITHIN A VERTICAL SHAFT, PER OBC 3.1.9.4(4)(b)
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

N 10. ALL PLUMBING SYSTEM SHALL COMPLY WITH PART 7 OF OBC AND BE TESTED AND INSPECTED PRIOR TO
COVERING. PROVIDE PIPE SYSTEM PRESSURE TO ENGINEER
N
FIRST FLOOR - DOMESTIC WATER - NEW WORK
MEZZANINE - DOMESTIC WATER - NEW 11. ALL PLUMBING MATERIALS SHALL BE SUITABLE FOR USE IN BUILDING OF NON-COMBUSTIBLE
SCALE: 1 : 75 CONSTRUCTION, AS PER 3.1.5.16 OF THE ONTARIO BUILDING CODE
SCALE: 1 : 75
12. INSTALL CLEANOUTS IN SANITARY AND STORM DRAINAGE SYSTEMS IN COMPLIANCE WITH 7.4.7 OF OBC
SUCH THAT ALL PIPING IS ACCESIBLE FOR CLEANING

13. ALL DEVICES REQUIRING A WATER SUPPLY CONNECTION SHALL BE EQUIPPED WITH APPROPRIATE
BACKFLOW PREVENTION DEVICE IN COMPLIANCE WITH CAN/CSA B64.10-11

14. THE MAXIMUM WATER TEMPERATURE DELIVERED BY FIXTURES SHALL BE LIMITED TO 49 DEG.C , EXCEPT
FOR DISHWASHER AND CLOTHES WASHER

15. NEW PLUMBING FIXTURES SHALL COMPLY WITH THE WATER CONSUMPTION REQUIREMENTS OF PART 7
OF OBC

16. EXPOSED PIPING IN FINISHED AREAS SHALL BE CHROME PLATED UNLESS NOTED OTHERWISE

ERCA
17. ALL PIPING SYSTEM SHALL BE IDENTIFIED BY MARKINGS THAT ARE PERMANENT, DISTINCT AND EASILY
RECOGNIZED PER PART 3 AND PART 7 OF OBC

18. ALL TESTABLE BACFLOW PREVENTION DEVICES SHALL BE TESTED BY QUALIFIED PERSONNEL, TAGGED,
AND TEST REPORT SUBMITTED TO INSPECTOR PRIOR TO PUTTING PIPE SYSTEM INTO SERVICE Drawn By Checked By
ai ai
6/1/2020 9:20:17 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

ELECTRIC
RADIANT
HEATER

12 T T
12 DOWN TO
SERVE DIFFUSERS
RH AHU-2 AT FIRST FLOOR
LEVEL (TYP) This drawing is not to be used for
construction unless it is countersigned
ELECTRIC SD
by the Project Architect
275
RADIANT
VESTIBULE HEATER

8"ø
Issued For (YYMMDD)
SD
101 275 TENDER 2020.06.01
EXHAUST

8"ø
AIR DUCT UP
34 TO ERV 34
11"ø 8"ø

FD 8"ø
18"x5" SD SD SD SD
275 275 275 275
WELCOME CENTRE
ATTIC AREA

13"ø
SD4 EG1
205 400 102 12"X12" DUCT 118 OPEN AREA
DOWN C/W FIRE
DAMPER
5 WOMEN W/R 1 5 AT PENETRATION 1

12"ø
10"x5"
113 M305 M305 8"ø

SD
SD 275
275

15"ø
T RH
8"x6"

COMMON HALLWAY
6 112
6
ELECTRIC CORRIDOR

Date
RADIANT TD 200CFM

14"ø
HEATER SD4 103
10"x5"
200 ELECTRIC
RADIANT 12"X12" DUCT SD3

T HEATER DOWN 205 8"ø

DUCT UP TO SERVE
AHU-3 SD4 OFFICE SD4

16"ø
TO AHU-3 100 100 WASHROOMS AND
SD3
10"x8"

205 104 SERVERY IN DUCT DOWN

EG1 FD FD TO SERVE
FIRST FLOOR
7 7

AHU-02

Revision Schedule
400

AHU-03
SD4 WITH FIRE FIRST
10"x5" 8"x5" 17"ø
200 MEN W/R DAMPER AT FLOOR 18"x8"
FLOOR WITH
PENETRATION FIRE DAMPER
111 FD

Description
AT THE
8"x6"
10"x8"

18"x5"

DUCT UP FAL FLOOR

TO AHU-2 900 PENETRATION

10"ø
10"x5" RA-1
8 KW DUCT HEATER 12"ø
DH
6"x5"
UNIVERSAL WR 1725 FD
IN FRESH AIR DUCT
12"x6"

10"ø
4"ø

105 C/W BUILT IN, AIR

EXHAUST AIR
EG2 FLOW SENSOR, MEZZ. (OPEN)
RANGE HOOD TO LOUVRE
8"x6"

150
DUCT DISCHARGE
8 BE SUPPLIER AND PN-WL-10X3 8

14"ø
8"x5" 8"x5"
EAL TEMPERATURE FUTURE 115
6"x5"

INSTALLED BY GC SD4 150 ERV

120 EF-1 SENSOR ELEVATOR AREA
CLOSET

"ø
THERMAL CUTOFF.

12
10"x5"

OD-1 110 6"x5" THERMOLEC

STORAGE
HEAT PN RFC-8-12-208-1-
4"ø

No.
RH B1AG WITH SCR - EAL-2 10"ø
PUMP SD4 107 900
OUTDOOR SD4 100 TD 50CFM MODULATING
MEZZ. BRIDGE
UNIT 200
SERVERY CONTROLLER
AHU-01
116
109 EG2 8"x5"
EAL
150
256 INDOOR UNIT
EF-2 C/W MULTI KIT PN-MW-NP562X3
9 9 AND CHANGE OVER BOX
COB04M132B22S RA-1
DOWN TO
SERVE DIFFUSERS

17"ø
EXHAUST AIR 1725
NOTE: ENSURE 1000MM AT FIRST FLOOR
LOUVRE
CLEARANCE LEVEL (TYP)
PN-WL-10X3
AROUND EQUIPMENT
14"ø
SD
SD
& FUTURE ELEVATOR
295 SHAFT
295
8"ø

14"ø
8"ø
SD
SD

AIR DISTRIBUTION
295
295

14"ø
10 10

12"ø
12"ø
SD SD
295 295
SD 8"ø
SD
295 295

2 CREATIVE COMMONS 2
M305 108 M305 OPEN AREA

8"ø
11 11

8"ø
SD SD
295 295
8"ø 8"ø

SD SD
295 295

John R. Park Homestead Heritage Centre

AHU-1
T
12 12

915 County Road 50, Essex, Ontario N0R 1G0

13 13
THESE TWO DC CEILING FANS TO BE
EQUIPPED WITH ISOLATION SWITCH FOR EACH CEILING
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

A B C
D CL E F A B C
D CL E F
FAN.THIS IS REQUIRED WHEN PROGRAMMING
REMOTE AND RECIEVER TO PAIR TOGETHER
G G

H
H

N
N
MEZZANINE - HVAC - NEW WORK
FIRST FLOOR - HVAC - NEW WORK SCALE: 1 : 75
SCALE: 1 : 75

ERCA
Drawn By Checked By
ai ai
6/1/2020 9:20:20 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

MODEL NECK SIZE / FACE SIZE / 1. PROVIDE NEW SUPPLY AND RETURN AIR DUCT WITH INSULATION. ALL DUCTS SHALL BE SEALED TO A CLASS A SEAL LEVEL
TYPE MARK AIRFLOW MANUFACTURER REMARKS IN ACORDANCE WITH SMACNA STANDARDS.
TBD TBD
2. ALL VOLUME CONTROL DAMPERS, FILTERS AND EQUIPMENT SHALL HAVE ADEQUATE SPACE AND SHALL REMAIN
ROUND THREE CONE DIFFUSER, 3 POSITION ADJSUTABLE,B12 STANDARD ACCESIBLE FOR SERVICE AND MAINTENANCE AFTER INSTALLATION.
SD 275CFM PRICE INDUSTRIES RCDE 08" 14" FINISH 3. ALL PIPE, INSULATION AND MATERIALS EXPOSED TO RETURN AIR CEILING PLENUM SHALL BE NON-COMBUSTIBLE.
4. ALL DUCT PENETRATIONS OF FIRE RATED SEPARATION SHALL BE EQUIPED WITH FIRE DAMPER. REFER TO
SD 250CFM PRICE INDUSTRIES RCDE 08" 12" ROUND THREE CONE DIFFUSER, 3 POSITION ADJSUTABLE,B12 STANDARD ARCHITECTURAL DRAWINGS FOR LOCATION AND RATINGS OF FIRE SEPARATION.
FINISH 5. ALL VOLUME CONTROL DAMPERS SHALL REMAIN ACCESIBLE FOR AIR BALANCING.
6. FLEXIBLE DUCT CONNECTORS CONTAINING COMBUSTIBLE MATERIAL SHALL BE LIMITED TO MAXIMUM 4.0 M LENGHT AND
SD3 SD 12" ROUND THREE CONE DIFFUSER, 3 POSITION ADJSUTABLE,B12 STANDARD SHALL BE USED IN THE HORIZONTAL ONLY. 180 Eugenie Street West
205CFM PRICE INDUSTRIES 08" Windsor, ON N8X 2X6
FINISH 7. ERV SHALL BE INSTALLED AND MAINTANED IN A MANNER THAT WILL PREVENT CONTAMINATION OF FRESH AIR STREAM
519.258.1390
WITH EXHAUST AIR AND WILL BE ADJUSTED AND CONTROLLED TO MAINTAIN ACCEPTABLE INDOOR AIR QUALITY
06" 8. OWNER SHALL BE PROVIDED WITH OPERATING AND MAINTENANCE INSTRUCTION.
SD4 100CFM PRICE INDUSTRIES SD 24"X24" SQUARE DIFFUSER 9. HANGER AND SUPPORTS:
9.1 INSTALL DUCTS IN ACCORDANCE WITH ASHRAE AND SMACNA AND AS INDICATED.
9.2 DO NOT BREAK CONTINUITY OF INSULATION AND VAPOUR BARRIER WITH HANGERS OR RODS.
SD4 120CFM PRICE INDUSTRIES SD 06" 24"X24" SQUARE DIFFUSER 9.3 SUPPORT RISERS IN ACCORDANCE WITH SMACNA.
9.4. SUPPORT FLEXIBLE DUCT IN ACCORDANCE WITH SMACNA.
9.5. STRAP HANGERS SHALL BE OF THE SAME MATERIAL AS THE DUCT BUT ONE SHEET METAL THICKNESS HEAVIER THAN
SD4 200CFM PRICE INDUSTRIES SD 08" 24"X24" SQUARE DIFFUSER DUCT. INSTALL IN ACCORDANCE WITH SMACNA. MAXIMUM SIZE SUPPORTED BY STRAP HANGERS IS 500 MM.
9.6. ANGLE HANGERS SHALL BE GALVANIZED STEEL COMPLETE WITH GALVANIZED RODS, WASHERS AND LOCKING NUTS. This drawing is not to be used for
construction unless it is countersigned
18X8 - FRESH AIR HOODED WALL CAP, BLACK ENAMEL FINISH, BUILT IN BIRD SCREEN SIZES AS FOLLOWS:
FAL 900CFM GREENHECK WC-18X8 by the Project Architect
AND DAMPER DUCT SIZE (IN) ANGLE SIZE (IN) ROD SIZE (IN)
UP TO 30 1X1X3/16 1/4"
Issued For (YYMMDD)
EG2 150CFM PRICE INDUSTRIES 80 12" 24"X24" EXHAUST AIR GRILL, B12 STANDARD WHITE FINISH 30 TO 43 11/2X1/1/2X3/16 1/4"
TENDER 2020.06.01
42 TO 60 11/2X11/2X3/16 3/8"
EXHAUST AIR HOODED WALL CAP, BLACK ENAMEL FINISH, BUILT IN BIRD SCREEN 9.7. HANGER SPACING SHALL BE AS FOLLOWS:
EAL-2 800CFM GREENHECK WC-18X8 18X8 - AND DAMPER DUCT SIZE (IN) SPACING (IN)
UP TO 60 120
- 60 AND OVER 100
EAL 150CFM PRICE INDUSTRIES WL-10X3 10"X03" EXHAUST AIR LOUVRE 9.8. UPPER HANGER ATTACHEMENTS AS FOLLOWS:
- FOR CONCRETE: USE MANUFACTURED CONCRETE INSERTS
RA-1 1640CFM PRICE INDUSTRIES 10 - 48"X12" PERFORATED RETURN GRILLE WITH FIRE DAMPER INBUILT - FOR STEEL JOINTS: USE MANUFACTURED JOIST CLAMP OR STEEL PLATE WASHER
- FOR STEEL BEAMS: USE MANUFACTURED BEAM CLAMPS
10. ROOF MOUNTED CONDENSING UNIT SUPPORTS SHALL BE ANCHORED TO WITHSTAND ANTICIPATED ENVIRONMENTAL WIND
LOADS.
1640CFM PRICE INDUSTRIES - 11. PROVIDE AIR BALANCING REPORT TO ENGINEER.
RA-2 10 48"X14" PERFORATED RETURN GRILLE WITH FIRE DAMPER INBUILT
12. MAXIMUM NUMBER OF PEOPLE 90 PERSONS.

SEQUENCE OF OPERATIONS:

1. THE HVAC SYSTEM CONTROL INCLUDES FOUR (4) WIRELESS PROGRAMABLE THERMOSTATS IN THE CONDITIONED SPACES
IN LOCATIONS SHOWN ON M301.

Date
2. THE THERMOSTATS SHALL ALLOW THE OCCUPANT TO CHOOSE THE HEATING OR COOLING MODE, SET THE OCCUPANCY
SCHEDULE AND THE ROOM TEMPERATURE SET-POINT. MOUNT AT 48" AFF OR AS DIRECTED BY THE OWNER.

3. INDOOR UNIT ID-1, ID-2, ID-3 & ID-4 SHALL RUN AS PER THE SCHEDULE:
• OCCUPIED PERIOD (7:30 AM - 5:00 PM ON WEEKDAYS) (ADJ.)
ROOM TEMPERATURE SET-POINT:
HEATING MODE: 72°F (ADJ.)
COOLING MODE: 75°F (ADJ.)

Revision Schedule
• UNOCCUPIED PERIOD (5:00 PM - 7:30 AM ON WEEKDAYS AND ALL DAY AT WEEKENDS) (ADJ.)
ROOM TEMPERATURE SET-POINT:
HEATING MODE: 65°F (ADJ.)
COOLING MODE: 82°F (ADJ.)

Description
No.
AIR DISTRUBUTION
John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

ERCA
Drawn By Checked By
ai ai
6/1/2020 9:20:36 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

C
D CL E F G
H A B C
D CL E
T/O RIDGE BEAM T/O RIDGE
T/O BEAM
RIDGE BEAM T/O RIDGET/O
BEAM
RIDGE BEAM T/O RIDGE BEAM
8392 8392 8392 8392 8392 8392

180 Eugenie Street West

Windsor, ON N8X 2X6
519.258.1390
T.O.GIRDER TRUSS T.O.GIRDER TRUSS T.O.GIRDER TRUSS T.O.GIRDER TRUSS
6700 6700 6700 6700

This drawing is not to be used for

construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

6247
MEZZANINE MEZZANINE
MEZZANINE MEZZANINE
MEZZANINE MEZZANINE TENDER 2020.06.01
T.O.WALL
T/O
2910 WALLPLATE
PLATE T/O WALL
T.O.PLATE
WALL
2910 PLATE
2910 T.O. WALL
2910 T/O WALL
2910 PLATEPLATE T.O.
T/O WALL PLATE
2910
2650 2650 2650 2650 2650 2650
3810
3116

FIRST
1ST FLOOR
FLOOR 1ST FLOOR
FIRST FLOOR FIRST1ST
FLOOR
FLOOR FIRST
1ST FLOOR
0 0 0 0 0 0

Date
WELCOME CETRE MEP ELEVATION CREATIVE COMMONS MEP ELEVATN

Revision Schedule

Description
No.
SECTIONS
John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

WELCOME CENTRE CORRIDOR CREATIVE COMMONS

ERCA
Drawn By Checked By
ai ai
6/1/2020 9:21:33 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

TOTAL TOTAL MAX

REFERENCE DESCRIPTION COOLING (MBH) HEATING (MBH) MANUFACTURER MODEL # MCA (A) FUSE VOLTAGE PHASE/HZ WEIGHT (LBS) REMARKS
SIZE
YORK OR YVAHR192B32S 76/68 208 3/60 OUTDOOR UNIT COMPLETE WITH REFRIGERANT PIPING, R410A REFRIGERANT
OD-1 HEAT PUMP / OUTDOOR UNIT 192 216 90 860
APPROVED EQUAL AND COMPLETE ACCESSORIES. TO BE MOUNTED ABOVE SNOW LEVEL
C/W MW-NP562X3 ONE MULTI KIT, COB04M132B22S 2 CHANGE OVER BOXES

180 Eugenie Street West

Windsor, ON N8X 2X6
INDOOR UNIT FOR MULTI-ZONE PUMP SYSTEM SCHEDULE 519.258.1390

AIR TOTAL TOTAL

REFERENCE DESCRIPTION FLOW HEATING (MBH) COOLING MANUFACTURER MODEL # CONDENSATE VOLTAGE PHASE/HZ WEIGHT (LBS) REMARKS
(CFM) (MBH) DRAIN (OD)

AHU-1 INDOOR UNIT 1765 81 72 YORK OR YIDH072B21S 1-1/4 208 1/60 170 INDOOR UNIT C/W WIRED REMOTE CONTROLLER CIW01 AND RETURN DUCT SMOKE
APPROVED EQUAL DETECTOR
This drawing is not to be used for
AHU-2 INDOOR UNIT YORK OR INDOOR UNIT C/W WIRED REMOTE CONTROLLER CIW01 AND RETURN DUCT SMOKE construction unless it is countersigned
1765 81 72 YIDH072B21S 1-1/4 208 1/60 170
APPROVED EQUAL DETECTOR
by the Project Architect

AHU-3 INDOOR UNIT 812 34 30 YORK OR INDOOR UNIT C/W WIRED REMOTE CONTROLLER, CIW01 Issued For (YYMMDD)
APPROVED EQUAL YIDH030B22S 1-1/4 208 1/60 113
TENDER 2020.06.01

EXHAUST FAN SCHEDULE (GREENHECK OR APPROVED EQUAL)

PERFORMANCE ELECTRICAL
REFERENCE SERVES MANUFACTURER MODEL RPM FLA WEIGHT REMARKS
HP/WATTS CFM ESP (" W.G) (A) (lbs)
VOLTAGE PHASE CYCLE (HZ)
C/W BIRD SCREEN, DISCONNECT SWITCH & BACKDRAFT DAMPER AND TO RUN CONTINOUSLY DURING
EF-01 UNIVERSAL GREENHECK CSP-B150 1050 141 150 0.25 115 1 60 1.70 16 WORKING HOURS, MOTOR RATED FOR CONTINUOUS USE, WALL LOUVERED DISCHARGE PN-10X3 (SHIPPED
WC
LOOSE)
C/W BIRD SCREEN, DISCONNECT SWITCH & BACKDRAFT DAMPER AND TO RUN CONTINOUSLY DURING
EF-02 STORAGE GREENHECK CSP-B150 1050 141 150 0.25 115 1 60 1.70 16 WORKING HOURS, MOTOR RATED FOR CONTINUOUS USE, WALL LOUVERED DISCHARGE PN-10X3 (SHIPPED
LOOSE)

ENERGY RECOVERY VENTILATOR (ERV) SCHEDULE

Date
WATER REFILLING STATION-ELKAY AIRFLOW STATIC
REFERENCE DESCRIPTION (CFM) PRESSURE MANUFACTURER MODEL # MOP FLA MCA VOLTAGE PHASE/HZ WEIGHT (LBS) REMARKS

ENERGY RECOVERY VENTILATOR 795 0.75" JOHNSON CONTROLS TERV060 208 1/60 ERV WITH DIGITAL WALL CONTROLLER, VARIABLE SPEED CONTROLLER, ECM
ERV 15 4.9-5.1 10.1 211
RANGE: 250-925 OR APPROVED EQUAL MOTORS-VARIABLE VELOCITY OPTION
OPTIONS: ELECTRICAL DUCT HEATER, THERMOLEC # RFC-8-12-208-1-B1AG

Revision Schedule

Description
ELECTRIC TANKLESS WATER HEATER SCHEDULE

MODEL WATTAGE (KW) VOLTAGE AMPEREAGE ACTIVATION GPM WEIGHT (LB) LOCATION
TYPE MARK MANUFACTURER (A)
WH 1 C4MA-280X 28 208 135 0.25 20
AO SMITH OR APPROVED EQUAL MEZZANINE
WH 2 C2VA-140X 14 208 67 0.25 13
RANGE HOOD

No.
WATER REFILLING STATION

TYPE MARK MANUFACTURER MODEL COLOR FILTER RATED WATTS AMP VOLTAGE GPH REMARKS
FINISH
LIGHT INSTALLATION TO BE WALL MOUNTED AND STATION TO BE ADA
ELKAY OR APPROVED GREY - 360 COMPLAINT, CHILLED WATER, HANDS FREE, HIGH
WF EZSG8WSLK 6 115 8
EQUAL GRANITE EFFICIENCY,DRAIN

EQUIPMENT SCHEDULE
FIRE DAMPER SCHEDULE

MODEL MOUNTING WIDTH,

TYPE MARK DESCRIPTION MANUFACTURER REMARKS
POSITION HEIGHT
PRICE INDUSTRIES OR HORIZONTAL SQUARE DYNAMIC FIRE DAMPER, 1.5HR FIRE RATING, ROLL FORMED
FD FIRE DAMPER APPROVED EQUAL FDD-A 12"X12" GALVANISED STEEL, U.L LISTED 165'F
PRICE INDUSTRIES OR ROUND DYNAMIC FIRE DAMPER, 1.5HR FIRE RATING, ROLL FORMED
FD FIRE DAMPER APPROVED EQUAL FD-RD HORIZONTAL 12" DIA GALVANISED STEEL, U.L LISTED 165'F
PRICE INDUSTRIES OR ROUND DYNAMIC FIRE DAMPER, 1.5HR FIRE RATING, ROLL FORMED
FD FIRE DAMPER FD-RD HORIZONTAL 18" DIA
APPROVED EQUAL GALVANISED STEEL, U.L LISTED 165'F

PRICE INDUSTRIESOR ROUND DYNAMIC FIRE DAMPER, 1.5HR FIRE RATING, ROLL FORMED
FD FIRE DAMPER FD-RD HORIZONTAL 10" DIA
APPROVED EQUAL GALVANISED STEEL, U.L LISTED 165'F

RADIANT PANEL-ELECTRIC SCHEDULE

INSTALLATION HEIGHT

John R. Park Homestead Heritage Centre

MODEL VOLTAGE WATTAGE REMARKS
TYPE MARK MANUFACTURER MIN FROM FFL MIN FROM CEILING

915 County Road 50, Essex, Ontario N0R 1G0

C/W PROGRAMMABLE ELECTRONIC WALL THERMOSTAT,
OUELLET / THERMA RAY OR AS2424-375-120
RP 8 FEET 2" 120V 375 SERIES OTH4000P
APPROVED EQUAL 23-3/4"X23-3/4" PANEL
MINIMUM INSTALLATION FROM FLOOR: 8ft. (2.4m)
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

ERCA
Drawn By Checked By
ai ai
6/1/2020 9:21:33 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

ROOF/ FLOOR STRUCTURE

ALL FLEXIBLE TO SOLID DUCT
CONNECTIONS TO BE MADE
WITH SELF LOCKING PLASTIC
TIE STRAP FOR A DISTANCE 1" WIDE BAND AS PER SMACNA
OF 3" MIN. 1" WIDE BAND AS
ROOF OR FLOOR STRUCTURE
PER SMACNA
This drawing is not to be used for
construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

VARIES

VARIES
TENDER 2020.06.01
VARIES

ALL SUPPLY AIR DIFFUSERES TO

BE PROVIDED WITH E.H. PRICE
MODEL VCR-7 RADIAL OPPOSED
FLEXIBLE DUCT BADE DAMPER
ALL SUPPLY AIR DIFFUSERS TO BE PROVIDED WITH E.H. PRICE
MODEL EG EQUALIZING GRID.

.
ALL SUPPLY AIR DIFFUSERS TO BE PROVIDED WITH E.H. PRICE DIFFUSER TO BE BALANCED
MODEL VCR-7 RADIAL OPPOSED BLADE DAMPER. SO THAT AIR LEAVES ALL
NOTE: WHERE CEILING SPACE AND/ OR
SIDES EQUALLY
305

OBSTRUCTIONS WILL NOT ALLOW 90o ELBOW &

MIN. 12" OF STRAIGHT DUCT OFF TOP
DIFFUSER TO BE BALANCED SO THAT AIR LEAVES SIDES EQUALLY. DIFFUSER

TYPICAL DUCT & DIFFUSER CONNECTION

Date
TYPICAL FLEXIBLE DUCT CONNECTION TYPICAL FIRE DAMPER INSTALLATION DETAIL

Revision Schedule

Description
CLEANOUT COVER
FLOOR DRAIN
SCREENED INLET
CONCRETE FLOOR SLAB FLOOR
GOOSENECK DUCT

CURB CAP THREADED CLEANOUT PLUG

30.00

No.
DRIP EDGE
°

VARIES
CLEANOUT TO BE FULL SIZE VENT (IF REQUIRED)
CHROME PLATED ACCESS 3/8" THREADED RODS WITH NUTS
OF DRAIN PIPE FOR UP TO 4"
ROOF CURB BY GENERAL COVER ON FINISHED WALL ON BOTH SIDES OF CHANNEL
3/8" CW
CONTRACTOR - WOOD FRAMING
30" MIN.

TO BE MIN. 2" X 12" UNISTRUT P1000 (LENGTH TO SUIT)

DRILL HOLES TO SUIT 3/8" DIA.
ROOF MEMBRANE FINISHED WALL SURFACE
CANT STRIP BOLTS AS REQUIRED. OPEN FACE
OF UNISTRUT DOWN. FLOW

FLOW
2 - 2" X 6" BLOCK
MOTORIZED DAMPER WHERE TRAP SEAL PRIMER

TYPICAL DETAILS
INDICATED ON FLOOR PLANS FIL FACED DUCT INSULATION

'Y' FITTING
N N WASTE DRAIN
TYPICAL GOOSENECK DETAIL WALL CLEANOUT DETAIL FLOOR DRAIN DETAIL
SCALE: 1:2 SCALE: 1 : 8
FLOOR CLEANOUT DETAIL

John R. Park Homestead Heritage Centre

WHERE REQUIRED PROVIDE FIRE DAMPER AT WALL PENETRATION AS

915 County Road 50, Essex, Ontario N0R 1G0

NOTES: DETAILED IN TYPICALLY FIRE DAMPER INSTALLATION

1. PROVIDE THERMOSTATIC TEMPERING MIXING VALVE IN CEILING SPACE ON ALL SINK &
LAVATORY HW SUPPLIES. SET TEMPERATURE TO 105°F (40.5°C). REFER TO DETAIL BELOW. PROVIDE SHEET METAL RETAINING ANGLES ON BOTH SIDES OF WALL
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

2. CONFIRM ALL EXISTING PIPE SIZES ONSITE & CEASE WORK AND REPORT TO ENGINEER PENETRATION
IMMEDIATELY IF VARIANCES IN THE SIZES DESCRIBED ON THE DRAWINGS ARE FOUND.
3. CONFIRM EXISTING WATER PRESSURE ON ALL EXISTING DOMESTIC WATER PIPES PRIOR TO
COMMENCING WATER HOOK UP & REPORT RESULTS TO ENGINEER.

THERMOSTATIC TEMPERING VALVE 13 13 CW UP TO VANITY

UNDER COUNTER - ADJUST
DISCHARGE TEMP. TO 105°F (40.5°C). 13 T.H.W (105°F/40.5°C) UP TO
LAVATORY OR COUNTER SINK

DUCTWORK - DOUBLE ELBOW

INTERNALLY LINED WITH ACOUSTIC

ERCA
13 HW & CW DN FROM CEILING SPACE INSULATION
IN WALL TO BELOW LAVATORY OR
COUNTER TOP.

RETURN OR TRANSFER GRILLE AT

CEILING OR WALL WHERE REQUIRED -
Drawn By Checked By
N REFER TO FLOOR PLANS
ai ai
6/1/2020 9:21:34 AM

THERMOSTATIC VALVE PIPING DETAIL Project No

SCALE: 1:1 DIMENSIONS TO SUIT
DUCT/DIFFUSER SIZE RETURN AIR BOOT / TRANSFER DUCT DETAILS 2020
THIS LINE IS 4" LONG
Sheet No
TYPICAL SIDE TAKEOFF w/ DAMPER
THE INFORMATION INCLUDED IN THIS ELECTRONIC DRAWING FILE IS PROTECTED BY COPYRIGHT. UNAUTHORIZED USE OF THIS FILE WITHOUT THE WRITTEN PERMISSION OF ARCHITECTTURA INC. ARCHITECTS IS PROHIBITED.
ARCHITECTTURA INC. ARCHITECTS IS RESPONSIBLE ONLY FOR INFORMATION SHOWN ON A MECHANICAL REPRODUCTION OF THIS DRAWING FILE THAT HAS BEEN SIGNED AND SEALED BY A REGISTERED ARCHITECT EMPLOYED BY THE FIRM.
THIS DRAWING SHEET IS 36"X24" IN SIZE. IT IS RECOMMENDED THAT ANY REPRODUCTION, ELECTRONIC OR OTHERWISE, BE TO THE SAME SHEET SIZE
TO ENSURE THE ACCURACY OF DRAWING SCALES DEPICTED ON THIS SHEET. THIS DRAWING IS NOT TO BE SCALED - USE FIGURED DIMENSIONS ONLY.
M401
ELECTRICAL SPECIFICATIONS
11. RECORD DRAWINGS
PART A - GENERAL 11.1. KEEP A RECORD SET OF DRAWINGS ON THE SITE ON WHICH SHALL BE CLEARLY INDICATED, THE 1.2. PERFORM DEMOLITION WORK IN SUCH A MANNER AS TO AVOID HAZARDS TO PERSONS PR 11. LOCATION OF OUTLETS AND MOUNTING HEIGHTS 20. GROUNDING
EXACT LOCATION OF ALL OUTLETS, FIXTURES, FEEDER RUNS, PANELS, CONDUCTS, JUNCTION PROPERTY. WORK SHALL BE PERFORMED IN STRICT ACCORDANCE WITH ALL APPLICABLE 11.1. LOCATION OF OUTLETS SHOWN ON ELECTRICAL DRAWINGS IS TO BE CONSIDERED AS 20.1. GROUND ALL ELECTRICAL AND NON-ELECTRICAL EQUIPMENT BEING PART OF THIS PROJECT’S
1. CODES & REGULATIONS BOXES, PULL BOXES ETC. INFORMATION ON THESE DRAWINGS SHALL BE INCORPORATED IN THE CODES, REGULATIONS, BY—LAWS, AND STANDARDS. DEMOLISH AND REMOVE OF ALL EXISTING APPROXIMATE. DETERMINE THE EXACT MOUNTING HEIGHTS (AND LOCATIONS) OF OUTLETS IN SCOPE OF WORK WITH APPROVED FITTINGS AND GROUND CONDUCTORS AS REQUIRED BY ALL
1.1. COMPLETE THE INSTALLATION OF THE WORK IN ACCORDANCE WITH LATEST ADDITIONS OF THE AS-BUILT DRAWINGS UPON COMPLETION OF THE PROJECT ELECTRICAL AND TELECOMMUNICATION SYSTEMS WHERE SHOWN FOR DEMOLITION. NO THE FIELD WITH RELATION TO ARCHITECTURAL DRAWINGS AND EQUIPMENT BEING SERVED. IF PERTINENT CODES. DO NOT USE EMT CONDUITS AS MEANS OF GROUNDING. PROVIDE WITHIN
NATIONAL BUILDING CODE, ONTARIO ELECTRICAL SAFETY CODE, C.S.A. STANDARDS, U.L.C., PORTION OF THE SYSTEMS SHOWN FOR DEMOLITION MAY BE ABANDONED IN PLACE. CUT BACK MOUNTING HEIGHTS OR LOCATIONS OF OUTLETS IS NOT INDICATED OR CONFLICTING, CONFIRM ALL RACEWAYS SEPARATE GREEN INSULATION GROUNDING CONDUCTOR.
N.F.P.A., O.S.H.A. AND ALL OTHER CODES BY AUTHORITIES HAVING JURISDICTION AS REQUIRED. 11.2. PROVIDE DIMENSIONS AND ROUTING OF BELOW—GRADE OR BELOW—SLAB OR RAISED FLOOR T0 FLOOR, WALL, OR CEILING AND PLUG ENDS OF CONCEALED CONDUITS MADE OBSOLETE BY WITH CONSULTANT BEFORE PROCEEDING WITH ROUGH-IN. 20.2. CLEAN GROUNDING METAL CONTACT POINTS OF PAINT, RUST AND OTHER CONTAMINANTS.
COMPLY WITH ELECTRICAL AND BUILDING CODE BULLETINS IN FORCE AT TIME OF BID SERVICES. ALTERATIONS TO PERMIT REFURNISHING SURFACE. REMOVE EQUIPMENT, DEVICES, FIXTURES, 11.2. CHANGE LOCATION OF OUTLETS AT NO EXTRA COST OR CREDIT, PROVIDING DISTANCE DOES PROTECT EXPOSED GROUNDING CONDUCTORS FROM MECHANICAL DAMAGE WITH RIGID PVC
SUBMISSION. THESE CODES AND REGULATIONS CONSTITUTE AN INTEGRAL PART OF THE 11.3. ALL CIRCUITING AS INSTALLED AND POWER AND SYSTEM JUNCTION BOX LOCATIONS, AS WELL EXPOSED RACEWAYS, BOXES AND HANGERS MADE OBSOLETE BY THIS WORK UNLESS NOT EXCEED 3000 MM, AND INFORMATION IS GIVEN BEFORE INSTALLATION. DO NOT CONDUIT.
SPECIFICATIONS. AS CONDUIT ROUTES SHALL BE UPDATED. DESIGNATED SPECIFICALLY TO REMAIN. PROVIDE BLANK PLATES ON ALL UNUSED OUTLET INSTALL OUTLETS BACK-TO-BACK IN WALL; ALLOW 150 MM HORIZONTAL CLEARENCE BETWEEN 20.3. ALL GROUNDING SHALL CONFORM TO THE ELECTRICAL SAFETY CODE AND LOCAL AUTHORITY
1.2. THE ENGINEER HAS NOT SUBMITTED THE CONTRACT DRAWINGS TO THE ELECTRICAL SAFETY BOXES. EXISTING CONCEALED CONDUITS NOT INTERFERING WITH THE WORK OF THIS OR ANY BOXES. LOCATE LIGHT SWITCHES ON LATCH SIDE OF DOORS WHERE POSSIBLE. REQUIREMENTS.
AUTHORITY FOR APPROVAL. ESA COMMENTS SHALL BE INCORPORATED IN THE PROJECT USING 12. EXTRA WORK OTHER GRADE MAY REMAIN, BUT CONDUCTORS SHALL BE REMOVED BACK TO POWER SOURCE. 11.3. PRIOR TO ROUGH-IN, COORDINATE FINAL MOUNTING HEIGHTS OF SYSTEM OUTLET BOXES IN 20.4. PROVIDE SEPARATE GREEN INSULATED GROUND CONDUCTOR IN EVERY POWER CONDUIT TO
NORMAL CONTRACT PROCEDURES. CO-ORDINATE WITH THE AUTHORITIES AND PROVE 12.1. IN CASES WHERE EXTRA WORK OF ANY KIND IS REQUIRED, OBTAIN WRITTEN INSTRUCTIONS NO LIVE UNUSED LIVE CONDUCTORS SHALL BE LEFT IN PLACE. FIELD WITH OWNER’S REPRESENTATIVE. MOUNTING HEIGHT OF OUTLETS IS FROM FINISHED ALL DEVICES, LUMINAIRES, EQUIPMENT, AND WITH ALL FEEDERS.
180 Eugenie Street West
ADDITIONAL INFORMATION AS REQUIRED. FROM THE ARCHITECT/DESIGN CONSULTANT BEFORE PROCEEDING. PAYMENTS WILL BE MADE 1.3. EXISTING INSTALLATIONS ALTERED DURING THE DEMOLITION WORK SHALL BE PLACED IN SAFE FLOOR TO CENTERLINE OF OUTLET. INSTALL OUTLETS GENERALLY AT FOLLOWING HEIGHTS Windsor, ON N8X 2X6
1.3. THE ELECTRICAL CONTRACTOR SHALL ACT AS THE OWNER’S AGENT IN ACCORDANCE WITH FOR AUTHORIZED CHANGES ONLY OPERATING CONDITION AND SHALL REMAIN IN SERVICE, UNLESS OTHERWISE NOTED, AND UNLESS INDICATED OTHERWISE: 21. DIRECTORY 519.258.1390
SECTION 2 OF THE O.E.S.C. AND SHALL IMMEDIATELY UPON REWARD IF THE CONTRACT, SUBMIT 12.2. QUOTATION WITH BREAK DOWN OE MATERIAL, LABOR, OVERHEAD, PROFIT, ETC. SHALL BE SHALL BE RESTORED 70 SATISFACTORY OPERATING CONDITION. REROUTE EXISTING WIRING • LOCAL SWITCHES: 1400 MM 21.1. PROVIDE TYPEWRITTEN DIRECTORIES FOR NEW AND EXISTING PANELBOARDS WITHIN THE AREA
TO THE ELECTRICAL INSPECTION DEPARTMENT, THE NECESSARY NUMBER OF DOCUMENTATION FOR SUBMITTED FOR EACH CHANCE. LABOR UNITS SHALL BE BASED ON THE LATEST NATIONAL AND RACEWAYS THAT BECOME EXPOSED DUE TO REMOVAL OF EXISTING CONSTRUCTIONS. • WALL OUTLETS (RECEPTACLES, TELEPHONE, DATA, TV) OF WORK, TO REFLECT THE LATEST REVISIONS. LABELLING TO BE BASED ON ROOM NUMBERS
EXAMINATION, INSPECTION AND APPROVAL PRIOR TO THE COMMENCEMENT OF WORK. PAY ALL COSTS ELECTRICAL CONTRACTORS ASSOCIATION (NECA) LABOR UNITS COLUMN ONE FOR THE SUCH INSTALLATIONS ARE T0 BE REROUTED T0 LOCATIONS WHERE IT MAY BE CONCEALED AND • GENERAL: 400 MM AND/OR LOCATION AND LOAD TYPES.
AND ASSOCIATED FEES. COMPLETE DURATION OF THE PROJECT. MATERIAL PRICES SHALL BE BASED ON THE CURRENT CIRCUITS AFFECTED WHICH ARE T0 REMAIN IN OPERATION SHALL BE REWIRED AS REQUIRED TO • ABOVE TOP OF COUNTER SPLASH BACK: 175 mm
1.4. PROVIDE CERTIFICATE(S) OF ACCEPTANCE FROM THE AUTHORITY HAVING JURISDICTION, UPON NATIONAL PRICE SYSTEM WITH TRADE DISCOUNTS. HOURLY LABOR RATE SHALL INCLUDE ALL MAINTAIN ADEQUATE OPERATION. • HANDICAP PUSH BUTTONS: 1050 MM 22. INTERRUPTION OF SERVICES
COMPLETION OF WORK. RELATED CHARGES FOR SUPERVISION, HYDRO lNSPECl0N, HAND TOOLS, PARKING, CLEAN-UP, 1.4. WHERE CONDUITS OR OUTLETS ARE REMOVED, REMAINING RUNS OF RACEWAYS SHALL BE 11.4. EXACT LOCATIONS OF OUTLETS SHALL BE VERIFIED PRIOR TO INSTALLATION. THERE WILL BE 22.1. THE CONTRACTOR SHALL ASSUME FULL RESPONSIBILITY FOR ANY DISRUPTION TO THE EXISTING
1.5. THESE DRAWINGS SHALL BE READ IN CONJUNCTION WITH ARCHITECT / DESIGNERS’ AS-BULK DRAWINGS AND ADDITIONAL BONDING. RECONNECTED TO FORM CONTINUOUS RACEWAYS WITH NEY/ CONDUCTORS INSTALLED FROM EAST NO CREDITS OR EXTRAS FOR CHANGES IN OUTLET LOCATIONS WITHIN 10FT (3M) OF ORIGINAL SERVICES. THE EXISTING BUILDING MUST BE KEPT IN OPERATION AT ALL TIMES. ARRANGE WORK
DRAWINGS FOR DIMENSIONS. MOUNTING HEIGHTS, CONSTRUCTION DETAILS, FINISHES AND REMAINING OUTLET BOX. WHEREVER EXTENSIONS OR EXISTING WIRING AND CABLES ARE LAYOUT, IF INFORMATION IS GIVEN OUT BEFORE ROUGH-IN. IN SUCH A MANNER THAT INTERRUPTIONS IN SERVICES OCCUR ONLY AT SCHEDULED TIMES.
COLORS. 13. REVIEW BY CONSULTANT REQUIRED, CHECK AND VERIFY THE STATUS OF THE EXISTING WIRE AND CABLES AND THEIR 11.5. DO NOT INSTALL OUTLETS BACK TO BACK. STAGGER TO PREVENT SOUND TRANSFER. INTERRUPTIONS SHALL BE SCHEDULED WITH THE ARCHITECT/DESIGN CONSULTANT PRIOR TO
1.6. COORDINATION WITH MECHANICAL TRADE IS THE RESPONSIBILITY OF THE ELECTRICAL 13.1. CONSULTANT MAY ORDER ANY PART OF THE WORK TO BE REVIEWED, IF SUBMITTED CAPACITIES. SECURE THE ENGINEERS ACCEPTANCE OF THIS DATA PRIOR TO ORDER ANY NEW 11.6. ALL WALL MOUNTED ELECTRICAL POWER AND COMMUNICATION OUTLETS AND PLATES ARE TO COMMENCING WORK. OVERTIME WORK THAT MAY BE REQUIRED TO TIE-IN SERVICES AT NIGHT OR This drawing is not to be used for
construction unless it is countersigned
CONTRACTOR. NO EXTRA SHALL BE PROVIDED FOR FAILING TO COORDINATE AND CONFIRM PERFORMANCE DOCUMENTS (TEST AND INSPECTIONS REPORTS) ARE NOT ACCEPTABLE AND IF WIRING OR CABLES. WHENEVER IT IS NECESSARY TO WITHDRAW CONDUCTORS FROM EXISTING BE MOUNTED AS DIMENSIONED BY ARCHITECTURAL TRADE, UNLESS OTHERWISE NOTED AND ON WEEKENDS SHALL BE INCLUDED IN THE TENDER AMOUNT. by the Project Architect
INSTALLATIONS RELATED TO THE MECHANICAL TRADE. THE WORD IS SUSPECTED TO BE NOT IN ACCORDANCE WITH CONTRACT DOCUMENTS. IF, UPON RACEWAYS, NEW CONDUCTORS SHALL BE INSTALLED. CONFIRMED BY ARCHITECT PRIOR TO COMMENCING WORK.
REVIEW SUCH WORK IS FOUND NOT IN ACCORDANCE WITH CONTRACT DOCUMENTS OR DOES 1.5. VISIT THE SITE. EXAMINE THE EXISTING CONDITIONS AND BECOME FAMILIAR WITH THE EXTENT OF 11.7. UPON COMPLETION OF THE PROJECT, THE CONTRACTOR SHALL ENSURE THAT ALL OUTLETS, 23. DEFECT OR INTERFERENCE
Issued For (YYMMDD)
2. QUALIFICATIONS N0T SATISFY PERFORMANCE STANDARDS, CORRECT SUCH WORD AND PAY COSTS OF THE NECESSARY REMOVAL, RELOCATION, RECONNECTING, AND REROUTING OF THE ELECTRICAL SWITCHES, ETC. ARE IN GOOD WORKING ORDER. THIS SHALL INCLUDE ALL EXISTING 23.1. EXAMINE THE WORK OF THE OTHER TRADES, AS THEY AFFECT THIS DIVISION. REPORT AT ONCE
TENDER 2020.06.01
2.1. ELECTRICAL WORK IS TO BE CARRIED OUT BY ELECTRICAL CONTRACTORS LICENSED BY UB ADDITIONAL REVIEW AND CORRECTION. EQUIPMENT AND WIRING AS NECESSARY FOR THE COMPLETION OF THE PROJECT. RECEPTACLES AND FURNITURE FEEDS. TO THE ARCHITECT/DESIGN CONSULTANT ANY DEFECT OR INTERFERENCE THAT MAY AFFECT THE
ACCORDANCE WITH ONTARIO REGULATION 570/05 (LICENSING OF ELECTRICAL CONTRACTORS 11.8. COORDINATE INSTALLATION OF WALL-MOUNTED FIXTURES, OUTLETS, SWITCH PLATES AND WORK OF THIS DIVISION OR THE GUARANTEE OF THIS WORK.
AND MASTER ELECTRICIANS) MADE UNDER THE ELECTRICITY ACT. 14. SHUT DOWNS AND CONTINUITY OF EXISTING SERVICES AND SYSTEMS 2. BASIC INSTALLATION METHODOLOGY AND POWER EQUIPMENT VERIFY WALL FINISHES, SPECIAL MILLWORK CONDITIONS WITH ARCHITECT PRIOR TO
2.2. ALL ELECTRICAL EMPLOYEES SHALL HAVE A VALID CERTIFICATE OF QUALIFICATION AS 14.1. MAINTAIN CONTINUOUS SERVICES ON FEEDERS, CIRCUITS OR PARTIAL CIRCUITS, AND OUTLETS 2.1. ALL EQUIPMENT VOLTAGE RATING SHALL BE IN CONFORMANCE WITH CAN3-C235, PREFERRED ROUGH-INS. 24. MODIFICATIONS TO EXISTING ELECTRICAL SERVICES
ELECTRICIAN OR SHALL BE REGISTERED APPRENTICE IN CONFORMANCE WITH THE ONTARIO AND EQUIPMENT AFFECTED BY THIS WORK. EXCEPT WHERE OWNER GIVES WRITTEN VOLTAGE LEVELS FOR AC SYSTEMS, 0 TO 50,000V. 11.9. WHERE MORE THAN ONE FACE PLATE OCCURS, GANG TOGETHER WITH A COMMON FACE PLATE 24.1. VISIT THE SITE, EXAMINE THE EXISTING CONDITIONS AND BECOME FAMILIAR WITH THE EXTENT OF
COLLEGE OF TRADES AMD APPRENTICE ACT. EMPLOYEES REGISTERED IN PROVINCIAL PERMISSION FOR OUTAGE FOR SPECIFIED TIME. NOTIFY OWNER AND UTILITY COMPANIES OF 2.2. INSTALLATION OF EQUIPMENT SHALL BE MADE AS PER MANUFACTURER’S INSTRUCTIONS AND ALL OF THE SAME MANUFACTURER. THE NECESSARY REMOVAL, RELOCATION, RECONNECTING AND RE-ROUTING OF ELECTRICAL
APPRENTICE PROGRAM: PERMITTED, UNDER DIRECT SUPERVISION OF QUALIFIED LICENSED INTENDED INTERRUPTION MAIN SERVICES AND OBTAIN REQUIRED PERMISSION. WHERE WORK APPLICABLE CODES. ATTACH ELECTRICAL EQUIPMENT, COMPONENTS, AND DEVICES DIRECTLY TO EQUIPMENT AND WIRING AS REQUIRED FOR THE COMPLETION OF THE PROJECT. REVIEW AND
ELECTRICIAN, TO PERFORM SPECIFIC TASKS. PERMITTED ACTIVITIES: DETERMINED BASED ON INVOLVES BREAKING INTO OR CONNECTING TO EXISTING BUILDING SYSTEMS, GIVE THE OWNER STRUCTURE OR STRUCTURAL SUPPORTING ELEMENTS AS REQUIRED TO MEET THE SEISMIC 12. CLEANING CONFIRM WITH THE ARCHITECT’S DRAWINGS FOR THE COMPLETE EXTENT OF DEMOLITION AND
TRAINING LEVEL ATTAINED AND DEMONSTRATED OF ABILITY TO PERFORM SPECIFIC DUTIES 72 HOURS NOTICE FOR NECESSARY INTERRUPTION OF MECHANICAL OR ELECTRICAL SYSTEMS RESTRAINT REQUIREMENTS. SET EQUIPMENT AND COMPONENTS PLUMB AND LEVEL, ACCURATE TO 12.1. CLEAN AND TOUCH UP SURFACES OF SHOP-PAINTED EQUIPMENT SCRATCHED OF MARRED ALTERATION
THROUGHOUT COUSE OF WORK. KEEP DURATIONS OF INTERRUPTIONS, MINIMUM. WHEN POSITION INTENDED. DURING SHIPMENT OR INSTALLATION, TO MATCH ORIGINAL PAINT. CLEAN AND PRIME EXPOSED 24.2. THE CONTRACTOR SHALL BE RESPONSIBLE FOR DISCONNECTING AND REMOVING ALL ELECTRICAL
3. BUILDING STANDARDS REQUESTED, CARRY OUT INTERRUPTIONS AFTER NORMAL WORKING HOURS OR IN WEEKEND 2.3. INSTALL CABLES, CONDUITS AND FITTINGS EMBEDDED OR PLASTERED OVER, CLOSE TO NON-GALVANIZED HANGERS, RACKS AND FASTENINGS TO PREVENT RUSTING. REMOVE STAINS, EQUIPMENT FROM AREAS BEING ALTERED OR DEMOLISHED. WIRING, CONDUIT AND EQUIPMENT
3.1. COMPLETE ALL ELECTRICAL WORK IN ACCORDANCE WITH THE RELEVANT SECTIONS OF THE PERIOD AT NO ADDITIONAL COST TO OWNER BUILDING INTERFERENCE TO MAINTENANCE AND OPERATIONS STAFF BY ALLOWING A CLEAR PATH SPOTS, MARKS AND DIRT FROM ELECTRICAL EQUIPMENT AND DEVICES. CLEAN LIGHTING WHICH IS REQUIRED TO MAINTAIN SERVICE IN OTHER PARTS OF THE BUILDING SHALL BE
BASE BUILDING SPECIFICATIONS, DRAWINGS, AND STANDARDS TO THE SATISFACTION OF THE 14.2. ENSURE THAT ALL ACTIVE SYSTEMS TO AREAS OUTSIDE OF SCOPE OF WORK REMAIN AROUND EQUIPMENT. IN FINISHED AREAS CONCEAL CONDUITS, DUCTS AND WIRING IN FLOORS, REFLECTORS, LENSES, AND OTHER LIGHTING SURFACES. TEMPORARILY SUPPORTED, REROUTED, SERVICED OR RELOCATED AS REQUIRED.
CONSULTANT AND/OR THE BUILDING OWNER. THE AVAILABLE BASE BUILDING DOCUMENTS WILL OPERATIONAL AND IN SAFE AND SECURE MANOR DURING CONSTRUCTION PERIOD. WALLS AND CEILINGS, EXCEPT WHERE INDICATED OTHERWISE. BEFORE INSTALLATION INFORM 12.2. REMOVE WASTE PRODUCTS AND DEBRIS OTHER THAN THAT CAUSED BY OWNER OR OTHER 24.3. EQUIPMENT TO BE RELOCATED SHALL BE VERIFIED FOR WORKING CONDITION. PROVIDE NEW IF
BE MADE AVAILABLE FOR REVIEW BY THE BUILDING OWNER IF SO REQUIRED 14.3. RETAIN COMMUNITY OF SERVICE OF THE FIRE ALARM SYSTEM AND ANY OTHER SAFETY OR CONSULTANT IF THERE IS INTERFERENCE. INSTALL AS DIRECTED BY CONSULTANT. CONTRACTORS AT REGULARLY SCHEDULED TIMES. PRIOR TO FINAL REVIEW, REMOVE NECESSARY AND FEASIBLE. EXTEND WIRING/CONDUIT AND RECONNECT TO SUIT.
SECURITY SYSTEMS TO ALL OCCUPIED AREAS OF THE BUILDING THROUGHOUT THE 2.4. WHEREVER EXTENSIONS OF EXISTING WIRES OR CABLES ARE SHOWN ON DRAWINGS, CHECK AND SURPLUS PRODUCTS, TOOLS, CONSTRUCTION MACHINERY AND EQUIPMENT, AND LEAVE WORK 24.4. OBSOLETE CONDUITS AND CABLES SHALL BE DISCONNECTED FROM THEIR SOURCE OF SUPPLY,
4. SITE VISIT— EXAMINATION OF PROJECT DOCUMENTS AND EXISTING SITE CONDITIONS. CONSTRUCTION PERIOD. VERIFY WIRE AND CABLE SIZES, STATUS, AND CAPACITIES. OBTAIN THE DESIGN ENGINEER CLEAN AND SUITABLE FOR OCCUPANCY. CUT BACK AS FAR AS POSSIBLE, AND SHALL BE REMOVED. ALL EXISTING WIRING NOT REMOVED
4.1. PRIOR TO SUBMITTING ANY TENDER, CONTRACTORS SHALL CAREFULLY EXAMINE THE 14.4. REINSTATE ANY EXISTING SERVICES DISRUPTED DURING WORK NOT INTENDED TO BE ALTERED ACCEPTANCE OF THIS DATA BEFORE NEW WIRES OR CABLES ARE ORDERED OR INSTALLATION SHALL BE DISCONNECTED, BLANKED-OFF AND MADE SAFE.
DRAWINGS AND SPECIFICATIONS TO UNDERSTAND EXACTLY THE PROJECT SCOPE OF WORK AS PART OF THIS CONTRACT. COMMENCED. INSTALL LIGHTING FIXTURES, OUTLETS, PLATES, AND OTHER VISIBLE ITEMS 13. ROUTING OF EQUIPMENT 24.5. UNLESS OTHERWISE ADVISED, ALL BASE BUILDING LUMINAIRES, TRANSFORMERS, PANELBOARDS
AND THEY SHALL VISIT AND EXAMINE THE WORK SITE AND FULLY INFORM THEMSELVES OF ALL 14.5. PROVIDE RECONNECTIONS AND TEMPORARY INSTALLATIONS AS REQUIRED TO PERMIT THE PARALLEL TO BUILDING LINES UNLESS OTHERWISE NOTED. 13.1. NEW CONDUITS AND OTHER NEW SERVICES SHALL BE CAREFULLY ROUTED SO THAT THEY DO AND DISCONNECT SWITCHES WHICH ARE REMOVED SHALL BE HANDED OVER TO THE BUILDING
THE EXISTING CONDITIONS, LIMITATIONS AND DIFFICULTIES WHICH MAY ARISE. OWNER TO OCCUPY AREAS OF THE BUILDING DURING THE VARIOUS CONSTRUCTION PHASES. NOT INTERFERE WITH ANY EXISTING INSTALLATIONS. ROUTING OF EQUIPMENT IN BUILDING OWNER.

Date
4.2. THE CONTRACTORS SHALL INCLUDE IN THEIR TENDERS THE COST OF ALL LABOR, MATERIALS, REMOVE TEMPORARY INSTALLATIONS AT THE WORK COMPLETION. 3. WORKMANSHIP COMMON AREAS AND RISER ROOMS SHALL BE REVIEWED AND APPROVED BY BUILDING OWNER 24.6. ALL REMOVED EQUIPMENT AND MATERIALS WHICH ARE NO LONGER REQUIRED, UNLESS
EQUIPMENT AND SPECIALIZED SERVICES REQUIRED TO FULLY COMPLETE THE WORK 3.1. ALL WORK SHALL BE CARRIED OUT AND PERFORMED IN A WORKMANLIKE MANNER TO THE PRIOR TO INSTALLATION. ANY EXISTING CONDUITS, CABLE TRAYS, BUS DUCTS OR OTHER OTHERWISE NOTED, SHALL BECOME THE PROPERTY OF THE CONTRACTOR AND SHALL BE
4.3. NO EXTRAS WILL BE ACCEPTED FOR WORK WHICH COULD HAVE BEEN DETERMINED THROUGH A 15. WARRANTY SATISFACTION OF THE ARCHITECT/DESIGN CONSULTANT. ANY UNSATISFACTORY WORK BY THIS SERVICES THAT INTERFERE WITH THE NEW INSTALLATION SHALL BE RELOCATED UNDER THIS REMOVED FROM THE SITE UPON COMPLETION OF THE WORK.
CAREFUL EXAMINATION OF THE EXISTING SITE CONDITIONS BY AN EXPERIENCED PERSON. 15.1. THE CONTRACTOR SHALL PROVIDE THE OWNER WITH A WRITTEN ONE-YEAR WARRANTY, DIVISION SHALL BE REPLACED WITHOUT EXTRA COST TO THE OWNER. CONTRACT.
CONNECTING ON THE DATE OF ACCEPTANCE. THE WARRANTY SHALL COVER THE COMPLETE 3.2. THE CONSTRUCTION SITE SHALL BE KEPT CLEAN AND ANY DEBRIS AND CONSTRUCTION MATERIAL 13.2. ALL WIRING, CABLES ETC., IN CEILING SPACE ARE TO BE SECURED WITH INDEPENDENT CEILING 25. WORK IN AREAS WITHOUT CEILINGS / EXPOSED CEILING STRUCTURAL.
5. PERMITS & INSPECTIONS ELECTRICAL INSTALLATION. THE ELECTRICAL CONTRACTORS SHALL REPAIR AND / OR REPLACE SHALL BE REMOVED FROM THE SITE THROUGHOUT THE CONSTRUCTION PERIOD AND ON HANGERS. 25.1. DO NOT USE BX(AC-90) CABLES IN CEILING SPACE. ALL CONDUITS AND RACEWAYS MUST BE
5.1. THE ELECTRICAL C0NTRACT SHALL BE RESPONSIBLE TO OBTAIN AND PAY FOR ALL NECESSARY ANY DEFECTS IN MATERIALS DURING THE WARRANTY PERIOD AT THE TIME CONVENIENT O THE COMPLETION OF THE WORK. 13.3. CONTRACTOR TO SUPPLY AND INSTALL 90 DEGREE ANGLE, SEAL TIGHT FLEX CONNECTORS INSTALLED NEATLY IN APPEARANCE, RUNNING PARALLEL TO BUILDING LINES, AND AS HIGH AS
PERMITS AND INSPECTIONS AS REQUIRED OR REQUESTED. TENANT/BUILDING OWNER AND AT NO EXTRA COST. 3.3. PROVIDE TOOLS AND CLEAN UP EQUIPMENT. OBTAIN OWNER’S PERMISSION FOR THE USE OF BASE BETWEEN WALL FURNITURE FEEDS AND SYSTEM FURNITURE TO PREVENT THE POWER FEED POSSIBLE. PROVIDE PROPER BENDS AND/OR FITTINGS WHERE EQUIPMENT CROSSES BEAMS,

Revision Schedule
5.2. ONCE THE ELECTRICAL WORK HAS BEEN COMPLETED AMD ACCEPTED BY THE OWNER, TH BUILDING’S ELECTRICAL PLUMBING AND DRAINAGE OUTLETS. PROVIDE DAILY CLEAN UP AND PROPER FROM UNNECESSARY BENDS, TWISTS OR KINKS. DUCTWORKS, PIPES, ETC.
ELECTRICAL CONTRACTOR SHALL PROVIDE THE OWNER WITH CERTIFICATES VERIFYING THAT 16. RECORD AS-BUILT DRAWINGS DISPOSAL OF DEBRIS GENERATED BY THIS DAILY OPERATION. 25.2. MOUNTING HEIGHT OF SUSPENDED LUMINAIRES TO BE COORDINATED WITH ARCHITECT/DESIGN
THE WORK HAS BEEN COMPLETED IN ACCORDANCE WITH ALL CODES, BUILDING STANDARDS 16.1. PROVIDE AS: 14. FLOOR PENETRATION CONSULTANT, SITE CONDITIONS, AND ALL TRADES PRIOR TO ORDERING LUMINAIRES AND WORK.
AND ALL AUTHORITIES HAVE JURISDICTION. • BUILT DRAWINGS OF THE ACTUAL INSTALLATION AS SCANNED COPIES OF RED 4. COMPLETION OF CONTRACT 14.1. X-RAY AND OBTAIN WRITTEN APPROVAL FROM BUILDING OWNER PRIOR TO PENETRATING ANY MOUNTING HEIGHT OF EXIT SIGNS SHALL BE AS HIGH AS POSSIBLE AND TO MEET CODE. PROVIDE

Description
5.3. PRIOR TO REQUESTING THE CONSULTANTS LETTER *REVIEW OF GENERAL CONFORMANCE* FOR • LINE MARK UPS. 4.1. ALL THE INSTALLED EQUIPMENT MUST BE CLEANED AND TESTED BEFORE FINAL ACCEPTANCE BY STRUCTURAL SURFACES OR FLOOR SLABS AND CARRY OUT THE WORK IN ACCORDANCE WITH CONDUIT STEM MOUNT AS REQUIRED. EXIT SIGNS ARE TO BE VISIBLE FROM THE EXIT APPROACH
SUBMISSION TO THE MUNICIPAL BUILDING DEPARTMENT TO ALLOW OCCUPANCY, THE 16.2. AS-BUILT DRAWINGS SHALL INCORPORATE ALL CHANGES AND DEVIATIONS FROM TENDER OWNER. PROVIDE WRITTEN WARRANTY FOR ONE YEAR FOR ALL SYSTEMS AS REQUIRED. THE BUILDING STANDARDS. THE CONTRACTOR SHALL REPLACE OR REPAIR ANY ITEMS WHICH AND NOT OBSTRUCTED BY ANY ELEMENTS, INCLUDING LUMINAIRES, SIGNAGES, BULKHEADS,
FOLLOWING ITEMS MUST BE COMPLETED AND SUBMITTED TO THE CONSULTANTS, AS DRAWINGS, INCLUDING ALL MAIN CONDUIT RUNS, CABLE TRAYS, JUNCTION BOXES, AND 4.2. PROVIDE AS-BUILT DRAWINGS OF THE INSTALLATION TO THE ENGINEER FOR REVIEW. DRAWING FILES ARE DAMAGED DUE TO THIS WORK AT NO EXTRA COST TO THE BUILDING OWNER DUCTWORK, ETC. MOUNTING HEIGHT OF EMERGENCY HEADS SHALL BE MAXIMUM 9’-0” A.F.F.
APPLICABLE: INFORMATION RECORDED ON RECORD DRAWINGS DURING CONSTRUCTION. CAN BE OBTAINED FROM THE CONSULTANT. 14.2. ALL NEW SERVICES THAT PENETRATE THE FLOOR SLAB OR FIRE RATED WALLS OR CEILINGS PROVIDE CONDUIT STEM MOUNT AS REQUIRED. ENSURE HEADS ARE FREE FROM OBSTRUCTION
• SUBMIT ALL APPLICABLE INSPECTION REPORTS FROM AUTHORIZES HAVING JURISDICTION. 16.3. ENGINEER'S STAMP AND COMPANY LOGO SHALL BE REMOVED FROM DRAWINGS. DRAWINGS 4.3. INCORPORATE ALL CHANGES AND DEVIATIONS FROM THE TENDER DRAWINGS, SUBMIT A SET OF SHALL BE IN CONDUIT AND SHALL BE SEALED WITH AN APPROVED, NON-SHRINK, WATERPROOF AND ILLUMINATION INTERFERENCE.
• CONTINUALLY OF FIRE SEPARATIONS AT SERVICE PENETRATES MUST BE COMPLETE SHALL BE MARKED "AS —BUILT" ALONG WITH ELECTRICAL CONTRACTOR'S NAME. PRINTS TO THE CONSULTANT FOR REVIEW AND APPROVAL. MODIFY THE AS-BUILT DRAWINGS AS PER AND FIREPROOF SEALANT. 25.3. ENSURE THAT ALL EXISTING AND NEW CEILING MOUNTED EQUIPMENT, INCLUDING JUNCTION
• ALL SEISMIC RESTRAINT REQUIREMENTS MUST BE COMPLETE COMMENTS FROM ENGINEERS FOR PRESENTATION TO OWNER. BOXES, RECEPTACLES, SPEAKERS, FIRE ALARM DEVICES, ETC. ARE PROPERLY SUPPORTED AND
• PROVIDING CERTIFICATE OF ACCEPTANCE FROM ELECTRICAL SAFETY AUTHORITY 17. CLOSE-OUT DOCUMENTS 15. CUTTING, PATCHING AND FIRE STOPPING SECURED TO THE STRUCTURE. PROVIDE NEW BLANK COVER PLATE TO EXISTING JUNCTION
• ANY DEVICES NOT INSTALLED MUST HAVE THE WIRING MADE SAFE AND TERMINATED IN AN 17.1. AFTER COMPLETION OF THE PROJECT. PROVIDE THE FOLLOWING DOCUMENTS TO THE BUILDING 5. SCHEDULING 15.1. ELECTRICAL CONTRACTORS IS RESPONSIBLE FOR CUT OUT OR DRILL HOLES IN EXISTING BOXES AS REQUIRED.
OUTLET BOX COMPLETE WITH COVER OWNER, THE TENANT, AND THE ENGINEER 5.1. ALL WORK SHALL BE SCHEDULED AND COORDINATED TO AVOID ANY CONFLICTS WITH OTHER CONSTRUCTION (THROUGH WALL, CEILING, OR FLOOR) NEEDED TO ACCOMMODATE CABLE,
• ALL OUTLETS MUST HAVE COVER PLATES INSTALLED. ALL ELECTRICAL EQUIPMENT NOT • FULL SIZE AS-BUILD DRAWINGS ALONG WITH DISK(S) TRADES, BUILDING OWNER AND TENNANT(S) DURING OR AFTER CONSTRUCTION. ALLOW FOR ALL CABLE TRAY, CONDUIT, PIPING, RACEWAYS OR DUCTWORK. THE CONTRACTOR SHALL PROVIDE 26. FINISHES
LOCATED IN SERVICE ROOMS MUST HAVE COVERS AND / OR DOORS INSTALLED • HYDRO / ESA ELECTRICAL INSPECTION REPORT NECESSARY PREMIUM TIME, ALL ALLOWANCE FOR THIS SHALL BE INCLUDED IN THE TENDER SCANNING PRIOR TO PERFORMING ANY NEW OPENINGS THROUGH A STRUCTURAL ELEMENT 26.1. ALL FITTINGS SUPPORTS HANGER RODS, PULL BOXES, CHANNEL FRAMES, CONDUIT RACKS,

No.
• EMERGENCY LIGHTING SYSTEM MUST BE OPERATIONAL AND TESTED. PROVIDE • FIRE ALARM VERIFICATION REPORT AND CERTIFICATE PRICE. AND ENSURE THAT NO REINFORCING BAR IS CUT OUT WITHOUT APPROVAL OF A LICENSED OUTLET BOXES, BRACKETS, CLAMPS, ETC., TO HAVE GALVANIZED FINISH OR PAINT FINISH OVER
CERTIFICATION LETTER FROM EQUIPMENT MANUFACTURE INDICATING THE SYSTEM MEETS • WRITTEN WARRANTY STRUCTURAL ENGINEER AND THE BUILDING OWNER. ALL VOIDS AT FIRE RATED PENETRATIONS CORROSION-RESISTANT PRIMER.
CODE REQUIREMENTS. • OPERATION AND MAINTENANCE MANUALS 6. DELIVERY OF EQUIPMENT SHALL BE COMPLETELY SEALED WITH ULC APPROVED AND CERTIFIED FIRESTOPPING MATERIAL 26.2. ALL PANELBOARDS, MOTOR STARTERS, ETC., TO BE FACTORY FINISHED WITH BAKED ON ENAMEL.
• ALL EXIT LIGHTS MUST BE INSTALLED AND OPERATIONAL. 17.2. CLOSE OUT DOCUMENTS SHALL BE PROVIDED PRIOR TO APPLICATION FOR SUBSTANTIAL 6.1. DELIVERY SCHEDULE OF ALL MAJOR ITEMS OF EQUIPMENT SUPPLIED UNDER THIS CONTRACT IN STRICT ACCORDANCE WITH THE MATERIAL MANUFACTURER’S INSTRUCTIONS. ALL ENAMEL TO BE BAKED ON GLOSS OVER CORROSION RESISTANT PRIMER. PROVIDE TOUCH-UP

GENERAL ELECTRICAL NOTES -1

• FIRE ALARM SYSTEM AND DEVICES MUST BE OPERATIONAL. SUBMIT FIRE ALARM COMPLETION. SHALL BE SUBMITTED IN WRITING TO THE GENERAL CONTRACTOR AT THE START OF THE 15.2. ARRANGE FOR HOLES THROUGH EXTERIOR WALLS AND ROOF TO BE FLASHED AND MADE PAINT FOR MINOR DAMAGE TO FINISH ON FACTORY FINISHED EQUIPMENT. ITEMS SUFFERING
VERIFICATION REPORT PER CAN/ULC-S537 PROJECT. FAILURE TO IDENTIFY DELIVERY PROBLEMS MAY RESULT IN DELAY CLAIMS. WEATHERPROOF. MAJOR DAMAGE TO FINISH SHALL BE REPLACED AT THE DIRECTION OF THE CONSULTANT.
• IF ANY OF THE ABOVE ITEMS HAVE NOT BEEN COMPLETED AT THE TIME OF CONSULTANTS 18. OPERATION AND MAINTENANCE (O&A) MANUALS 6.2. CONTRACTOR SHALL ASSUME FULL RESPONSIBILITY TO RECEIVE, STORE AND HANDLE EQUIPMENT, 15.3. ELECTRICAL CONTRACTOR SHALL BEAR ALL COSTS OF CUTTING, PATCHING, INSULATION AND 26.3. PROTECT WORK SO THAT FINISHES WILL NOT BE DAMAGED OR MARRED DURING CONSTRUCTION.
INSPECTION. AND THE LETTER OF *ASSURANCE OF PROFESSIONAL 18.1. PROVIDE TWO (2) BINDER COPIES PLUS ELECTRONIC COPY THE OPERATION AND MAINTENANCE FIXTURES AND MATERIALS COVERED UNDER THIS CONTRACT. FIRE STOPPING RESULTING FROM THE ELECTRICAL WORK. CLEAN AND PRIME EXPOSED NON-GALVANIZED HANGERS, RACKS AND FASTENINGS TO PREVENT
• FIELD REVIEW AND COMPLIANCE* CANNOT BE ISSUED, ANY COSTS FOR SUBSEQUENT DATA MANUAL THAT SHALL INCLUDE PRODUCT DATA, MANUFACTURER’S CERTIFICATES AND 6.3. PROTECT EQUIPMENT AND MATERIALS IN STORAGE ON SITE, DURING AND AFTER INSTALLATION 15.4. ALL CUTTING AND PATCHING REQUIRED TO THE BUILDING STRUCTURE FOR THE WORK SHALL RUSTING.
INSPECTIONS WILL BE CHARGED TO THE CONTRACTOR. INSTRUCTIONS FOR INSTALLATION, MAINTENANCE AND OPERATION, TECHNICAL DESCRIPTIONS UNTIL FINAL ACCEPTANCE. PROVIDE POLYETHYLENE COVERS AND CRATES TO ADEQUATELY BE INCLUDED AS PART OF THIS CONTRACT, UNLESS OTHERWISE ADVISED BY THE GENERAL
AND PARTS LIST, WIRING AND SCHEMATIC DIAGRAMS, TEST AND VERIFICATION REPORTS, PROTECT EQUIPMENT. CONTRACTOR. OBTAIN APPROVAL FROM OWNER PRIOR TO ANY CUTTING. PART C – MATERIAL 1
6. INSURANCE SERVICE DEPOT LOCATIONS AND TELEPHONE NUMBERS, lNSPECT0N REPORTS AND 6.4. PROTECT EQUIPMENT AND MATERIALS OR LEAVE FACTORY COVERS IN PLACE. TAKE SPECIAL 15.5. WHERE CONDUITS PASS THROUGH FIRE RATED WALLS OR FLOORS, PROVIDE PROPER FIRE
6.1. PROVIDE INSURANCE FOR THE DURATION OF THE PROJECT TO PROJECT THE BUILDING OWNER, CERTIFICATES OE ACCEPTANCE FROM AUTHORITIES HAVING JURISDICTION, PANEL SCHEDULES, PRECAUTIONS TO PREVENT ENTRY OF ANY FOREIGN MATERIAL INTO WORKING PARTS OF STOPPING MATERIAL THAT BEARS LABEL OF CSA AND ULC, AND MAINTAIN FIRE RATING. ALL 1. GENERAL
TENANT, AND TRADES FROM ALL CLAIMS. SUBMIT AT THE TIME OF THE BID. PROOF OF AN AND WARRANTY LETTERS EQUIPMENT. SEALANT SHALL BE OF RE-ENTRANT TYPE WHERE APPLICABLE. 1.1. ALL MATERIALS AND EQUIPMENT SHALL BE NEW, CSA CERTIFIED AND MANUFACTURED TO THE
AMOUNT ACCEPTABLE TO BUILDING OWNER AND TENANT IN ACCORDANCE WITH FRONT END 18.2. O&M MANUALS SHALL INCLUDE: 15.6. SUPPORTING MEMBERS OF ANY FLOOR, WALL OR THE BUILDING STRUCTURE SHALL BE CUT STANDARDS SPECIFIED. WHERE THERE IS NO ALTERNATIVE TO SUPPLYING EQUIPMENT WHICH IS
REQUIREMENTS OF THE SPECIFICATIONS. • AS-BUILT DRAWINGS. 7. MATERIALS AND EQUIPMENT ONLY IN SUCH A LOCATION AND MANNER AS APPROVED BY THE BUILDING OWNER AND NOT CSA CERTIFIED, OBTAIN SPECIAL APPROVAL FROM LOCAL ELECTRICAL SAFETY AUTHORITY.
• TESTING AND COMMISSION REPORTS. 7.1. IMMEDIATELY UPON SIGNING CONTRACT, REVIEW PRODUCT DELIVERY REQUIREMENTS AND ARCHITECT.
7. CO-OPERATION AND CO-ORDINATION WITH OTHER CONTRACTORS. • INSPECTION CERTIFICATE ANTICIPATE FORESEEABLE SUPPLY DELAYS FOR ITEMS. IF DELAYS IN SUPPLY OF PRODUCTS ARE 15.7. ALL CUTS SHALL BE CLEAN, TRUE WITH SOME SMOOTH EDGES. WORK SHALL BE PERFORMED 2. WIRE AND CABLE
7.1. CO-OPERATE WITH OTHER CONTRACTORS IN CARRYING OUT THEIR RESPECTIVE WORKS AND • VERIFICATION REPORTS AND CERTIFICATES FOR ALL SAFETY SYSTEMS FORESEEABLE, NOTIFY CONSULTANT OF SUCH, IN ORDER THAT SUBSTITUTIONS OR OTHER WITHIN TOLERANCES ESTABLISHED IN CONFORMANCE WITH THE BEST STANDARD PRACTICE 2.1. ALL WIRE AND CABLES SHALL BE COPPER, MINIMUM #12 GAUGE. #12 AND #10 SOLID, #8 AND
CARRY OUT INSTRUCTIONS FROM THE GENERAL CONTRACTOR. • PANEL BOARD SCHEDULES REMEDIAL ACTION MAY BE AUTHORIZED IN AMPLE TIME TO PREVENT DELAY IN PERFORMANCE OF FOR THE APPLICABLE CLASS OF WORK. LARGER STRANDED, WITH RW90 INSULATION, 600 VOLT RATING UNLESS OTHERWISE NOTED. BX
7.2. CO-ORDINATE WORK WITH THAT OF OTHER CONTRACTORS. IF ANY PART OF WORK UNDER THIS • WARRANTIES WORK. CABLES ARE NOT ALLOWED TO BE USED TO PANELBOARDS OR EXPOSED.
CONTRACT DEPENDS FOR ITS PROPER EXECUTIONER RESULT OF ANOTHER CONTRACTOR, • TRAINING RECORDS 7.2. IN EVENT OF FAILURE TO NOTIFY CONSULTANT AT COMMENCEMENT OF WORK AND SHOULD IT 16. SEISMIC RESTRAINT 2.2. AC90 (BX) CABLE MAXIMUM WIRE SIZE TO BE #12 AWG UNLESS OTHERWISE NOTED. BX TO BE USED
REPORT PROMPTLY TO CONSULTANT, IN WRITING, ANY DEFECTS WHICH MAY INTERFERE WITH • OPERATION AND MAINTENANCE PROCEDURES SUBSEQUENTLY APPEAR THAT WORK MAY BE DELAYED FOR SUCH REASON, CONSULTANT 16.1. FURNISH SEISMIC RESTRAINT OF ELECTRICAL SYSTEMS IN CONFORMANCE WITH THE ONTARIO ONLY AS DROP TO LIGHTING FIXTURES AND AS DROP TO WIRING DEVICES IN PARTITIONS FROM
PROPER EXACTION OF WORK. • REVIEWED SHOP DRAWINGS OF ALL NEW EQUIPMENT RESERVES RIGHT TO SUBSTITUTE MORE READILY AVAILABLE PRODUCTS OF SIMILAR CHARACTER BUILDING CODE’S REQUIREMENTS. ENGAGE A LICENSED STRUCTURAL ENGINEER, WHO CEILING JUNCTION BOX / CONDUIT COMBINATION. MAXIMUM RUN OF BX TO BE 10 FEET WHERE
7.3. ELECTRICAL CONTRACTOR SHALL ASSUME FULL RESPONSIBILITY FOR LAYING OUT WORK AND 19. COMMISSIONING AT NO INCREASE IN CONTRACT PRICE OR CONTRACT TIME. PRACTICES UNDER VALID CERTIFICATE OF AUTHORIZATION ISSUED BY PEO, PROVIDE WRITTEN EXPOSED IN LAY-IN SUSPENDED CEILING SPACE ONLY. DO NOT INSTALL EXPOSED BX. DO NOT
FOR ANY DAMAGE TO THE OWNER OR OTHER TRADES CAUSED BY IMPROPER LAYOUT. 19.1. STARTUP EQUIPMENT TO NETA STANDARDS 7.3. MATERIAL AND EQUIPMENT SHALL BE NEW AND QUALITY SPECIFIED, CSA APPROVED AND/OR CONFIRMATION (SIGNED AND STAMPED) THAT NEW ELECTRICAL WORK HAS BEEN COMPLETED DAISY CHAIN BX BETWEEN LUMINAIRES.
19.2. MEGGER CIRCUITS, FEEDERS AND EQUIPMENT UP TO 350V WITH A 500V INSTRUMENT ULC CERTIFIED. MAINTAIN UNIFORMITY OF MANUFACTURE FOR ANY PARTICULAR OR LIKE ITEM IN GENERAL COMPLIANCE WITH THE OBC’S SEISMIC REQUIREMENTS. 2.3. ALL CONDUCTORS USED OUTDOOR OR IN WET LOCATIONS SHALL BE RWU90 COPPER.
8. ALTERATIONS, ADDITIONS OR REPAIRS TO EXISTING BUILDING 19.3. MEGGER 350V-600V CIRCUITS, FEEDERS AND EQUIPMENT WITH A 1000V INSTRUMENT. THROUGHOUT BUILDING EXCEPT WHERE SPECIFIED OTHERWISE. DEFECTIVE PRODUCTS 2.4. WIRE AND BOX CONNECTIONS – WIRE CONNECTORS: PVC INSULATION, STEEL SHALL BE SPRING
8.1. EXECUTE WORK WORTH LEAST POSSIBLE INTERFERENCE OR DISTURBANCE TO BUILDING 19.4. CHECK RESISTANCE TO GROUND BEFORE ENERGIZING = WHENEVER IDENTIFIED, WILL BE REJECTED REGARDLESS OF PREVIOUS INSPECTIONS. 17. ACCESS DOORS AND PANEL PRESSURE TYPE, CURRENT CARRYING PARTS COPPER OR COPPER ALLOY SIZED TO SUIT COPPER
OPERATIONS, OCCUPANTS AND NORMAL US OF PREMISES. ARRANGE WITH THE OWNER TO 19.5. LIGHTING CONTROL DEVICES AND CONTROL SYSTEMS SHALL BE TESTED T0 ENSURE THAT INSPECTION DOES NOT RELIEVE RESPONSIBILITY, BUT IS PRECAUTION AGAINST OVERSIGHT OR 17.1. ACCESS PANELS SHALL BE PROVIDED IN CEILINGS WHERE JUNCTION BOXES AND OTHER CONDUCTORS TO CSA C22.2 NO 64-1980.
FACILITATE EXECUTION OF WORK AS REQUIRED CONTROL HARDWARE AND S0FTWARE ARE CALIBRATED, ADJUSTED, PROGRAMMED, AND IN ERROR. REMOVE AND REPLACE DEFECTIVE PRODUCTS AT OWN EXPENSE AND BE ELECTRICAL EQUIPMENT CAN NOT BE LOCATED IN ACCESSIBLE LOCATIONS PROVIDED THAT 2.5. SPLICING CONNECTORS: FIXTURE TYPE CURRENT CARRYING PARTS COPPER OR COPPER ALLOY
8.2. REPAIR OR REPLACE PORTIONS OF EXISTING WORK WHICH HAVE BEEN ACCIDENTLY ALTERED PROPER W0RKINC CONDITION IN ACCORDANCE WITH THE CONSTRUCTION DOCUMENTS AND RESPONSIBLE FOR DELAYS AND EXPENSES CAUSED BY REJECTION. APPROVAL HAS BEEN OBTAINED FROM THE ARCHITECT/DESIGN CONSULTANT. SIZED TO FIT COPPER CONDUCTORS #12 AWG WITH INSULATING MATERIALS OF THERMOPLASTIC
DURING CONSTRUCTION OPERATIONS TO MATCH EXISTING OR ADJOINING WORK. MANUFACTURES INSTALLATION INSTRUCTIONS 17.2. PROVIDE ACCESS DOORS FOR NEW AND EXISTING CONCEALED VALVES, DAMPERS JUNCTION MATERIAL TO CSA C22.2 NO 75MM-83.
19.6. WHEN OCCUPANT SENSORS, TIME SWITCHES, PROGRAMABLE SCHEDULE CONTROLS, OR PHOTO 7.3. MATERIAL AND EQUIPMENT SHALL BE NEW AND QUALITY SPECIFIED, CSA APPROVED AND/OR BOXES, EQUIPMENT ETC. 2.6. CLAMPS TO CONNECTORS: TO CSA C22.2 NO 18-M1987 FOR FLEXIBLE CIRCUIT.
9. CONTRACT DOCUMENTS SENSORS ARE INSTALLED AT A MINIMUM THE FLOWING PROCEDURE SHALL BE PERFORMED: ULC CERTIFIED. MAINTAIN UNIFORMITY OF MANUFACTURE FOR ANY PARTICULAR OR LIKE ITEM 17.3. ACCESS DOORS SHALL MATCH WALL AND CEILING FINISHES. 2.7. LUGS, TERMINALS, OR SCREWS USED FOR TERMINATION OF WIRING TO BE SUITABLE FOR COPPER
9.1. THE DRAWINGS ARE DIAGRAMMATIC ONLY. DO NOT SCALE OR MEASURE DRAWINGS, BUT • CONFIRM THAT THE PLACEMENT, SENSITIVITY AND TIME OUT ADJUSTMENTS FOR OCCUPANT THROUGHOUT BUILDING EXCEPT WHERE SPECIFIED OTHERWISE. DEFECTIVE PRODUCTS 17.4. ACCESS DOORS IN GYPSUM CEILING SHALL BE RECESSED TYPE. CONDUCTORS.

John R. Park Homestead Heritage Centre

OBTAIN INFORMATION REGARDING ACCURATE DIMENSIONS, LENGTHS, ETC. BY SITE SENSORS YIELD ACCEPTABLE PERFORMANCE, LIGHTS THAT TURN OFF ONLY AFTER SPACE IS WHENEVER IDENTIFIED, WILL BE REJECTED REGARDLESS OF PREVIOUS INSPECTIONS. 17.5. ACCESS DOORS SHALL BE FLUSH TO EDGE OF FRAME, CONCEALED CONTINUOUS HINGE WITH 2.8. VOLTAGE DROP – FEEDER CONDUCTORS SHALL HAVE A MAX VOLTAGE DROP OF 2%. BRANCH
MEASUREMENTS. VACATED AND DO NOT TURN ON UNLESS SPACE IS OCCUPIED. INSPECTION DOES NOT RELIEVE RESPONSIBILITY, BUT IS PRECAUTION AGAINST OVERSIGHT OR SCREWDRIVER OPERATED CAM LATCH. DOOR CONSTRUCTION TO BE MINIMUM 14 GAUGE WITH CIRCUIT CONDUCTORS SHALL HAVE A MAX VOLTAGE DROP OF 3%
• CONFIRM THAT THE SWITCHES AND PROGRAMMABLE SCHEDULE CONTROLS ARE ERROR. REMOVE AND REPLACE DEFECTIVE PRODUCTS AT OWN EXPENSE AND BE RESPONSIBLE 16 GAUGE FRAME. INSULATION THICKNESS TO PROVIDE REQUIRED RATING. 2.9. PROVIDE FIRE RATED WIRING FOR ALL NEW FIRE ALARM CONNECTIONS IN ACCORDANCE WITH

915 County Road 50, Essex, Ontario N0R 1G0

9.2. CROSS REFERENCE THESE PLANS WITH THE MECHANICAL AND ARCHITECTURAL TRADES
THROUGHOUT THE COURSE OF THE PROJECT AND REPORT ANY DISCREPANCIES T0 THE PROGRAMED TO TURN THE LIGHTS OFF. FOR DELAYS AND EXPENSES CAUSED BY REJECTION. 17.6. SIZE DOORS TO ALLOW FOR ADEQUATE OPERATING/ MAINTENANCE CLEARANCE FOR DEVICES. THE LATEST BUILDING CODE REQUIREMENTS AND AS REQUIRED BY THE LOCAL AUTHORITIES
DESIGN TEAM BEFORE PROCEEDING WITH THE AFFECTED WORK. • CONFIRM THAT PHOTO SENSOR CONTROLS REDUCE ELECTRIC LIGHT LEVELS BASED ON THE • BODY ENTRY: 24”X 24”. HAVING JURISDICTION.
9.3. REPORT ANY DISCREPANCIES BETWEEN THE ARCHITECTURAL DRAWINGS, ELECTRICAL AMOUNT OF USEABLE DAYLIGHT IN THE SPACE AS SPECIFIED. 8. IDENTIFICATION • HAND ENTRY:12” X 12” 2.10. VOLTAGE DROP SHALL NOT EXCEED 3% IN A FEEDER OR BRANCH CIRCUIT. WHERE A CIRCUIT IS
8.1. IDENTIFY WITH LAMICOID NAMEPLATES ELECTRICAL EQUIPMENT SHOWN ON THE DRAWINGS 17.7. ACCEPTABLE DOORS SHALL BE ACUDOR MODEL AS PER ASSEMBLY, OR EQUAL BY LEHAGE: DEDICATED PROVIDE SEPARATE NEUTRAL CONDUCTOR WITH THE SAME SIZE AS PHASE
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

DRAWINGS AND BUILDING CONDITIONS AFFECTING PRICE OR INSTALLATION 70 THE ENGINEER

PRIOR T0 SUBMITTING BID. 20. LOAD BALANCING AND/OR MENTIONED IN THE SPECIFICATION SUCH AS PANELBOARDS, TRANSFORMERS, • CONCEALED PLASTER: PS-5015 CONDUCTOR. DO NOT SHARE NEUTRAL IN BRANCH CIRCUITS FEEDING RECEPTACLE LOADS.
9.4. CO-OPERATE WITH OTHER TRADES, CONTRACTORS IN LAYING OUT OF WORK SO AS NOT TO 20.1. MEASURE PHASE CURRENT TO PANELBOARDS WITH NORMAL LOADS (LIGHTNING) OPERATING AT MOTORS, DISCONNECT SWITCHES, TERMINAL CABINETS, AND SPECIAL RECEPTACLES. PROVIDE • CONCEALED DRYWALL: DW-5015 2.11. PROVIDE COPPER CONDUCTORS RW90XLPE TYPE, RATED AT 600 V, RUN WITHIN MINIMUM 21MM
CONFLICT WITH THE WORK OF OTHERS TIME OF ACCEPTANCE; ADJUST BRANCH CIRCUIT CONNECTIONS AS REQUIRED TO OBTAIN BEST NEATLY TYPED UPDATED PANEL SCHEDULES IN A PLASTIC HOLDER ON THE INSIDE DOOR OF • EXISTING DRYWALL: DW-5015 EMT CONDUITS. RUN CONDUITS EXPOSED IN UNFINISHED AREAS AND SERVICE ROOMS AND
9.5. THESE PLANS ARE TO BE USED IN CONJUNCTION WITH THE FURNITURE PLAN AND FURNITURE BALANCE OF CURRENT BETWEEN PHASES AND RECORD CHANGES. PANELBOARD, WITH COPY IN MANUAL. • FIRE RATED: FW-5050 / FB-5060 TO MATCH ASSEMBLY CONCEALED IN FINISHED AREAS PARALLEL TO BUILDINGS LINES, AND MAINTAIN MAXIMUM
INSTALLATION PLANS. 20.2. MEASURE PHASE VOLTAGE AT LOADS AND ADJUST TRANSFORMER TAPS TO WITHIN 2% OF 8.2. IDENTIFY WIRING WIRING WITH PERMANENT INDELIBLE IDENTIFYING MARKINGS ON BOTH ENDS HEADROOM. USE STEEL FITTINGS FOR EMT. MINIMUM CONDUCTOR SIZE #12 AWG FOR LIGHTING
9.6. IT IS THE INTENT OF THESE DRAWINGS AND SPECIFICATIONS THAT TH CONTRACTOR PROVIDES RATED VOLTAGE OF EQUIPMENT. OF PHASE CONDUCTORS AND FEEDERS AND BRANCH CIRCUIT WIRING. MAINTAIN PHASE 18. NOISE & VIBRATION AND POWER CIRCUITS AND #14 FOR CONTROLS EXCEPT AS OTHERWISE NOTED. WIRE
COMPLETE AND OPERATIONAL SYSTEMS AS REQUIRED. WHERE DIFFERENCES OCCUR, THE 20.3. PROVIDE UPON COMPLETION OR WORK, LOAD BALANCE REPORT: PHASE AND NEUTRAL SEQUENCE AND COLOUR CODING THROUGHOUT. IDENTIFY ALL PULL AND JUNCTION BOXES, 18.1. CARRY OUT THE WORK WITH A MINIMUM OF NOISE, DUST AND DISTURBANCE. ALL ELECTRICAL CONNECTORS SHALL BE ULC-LISTED FACTORY FABRICATED, SOLDERLESS METAL CONNECTORS
MAXIMUM CONDITIONS SHALL GOVERN. CURRENTS ON PANEL BOARDS, DRY TYPE TRANSFORMERS AND MOTOR CONTROL CENTER, WITH PERMANENT MARKER IDENTIFICATION INDICATING SOURCE PANELS AND CIRCUIT EQUIPMENT SHALL OPERATE WITHOUT OBJECTIONABLE NOISE OR VIBRATION TO THE OWNER’S (TWIST-ON PRESSURE) OF SIZES, AMPACITY RATINGS, MATERIALS, TYPES AND CLASSES FOR THE
9.7. ANY MISCELLANEOUS ITEMS, HARDWARE DEVICES, FIRE ALARM TESTING OR FACTORY OPERATING UNDER NORMAL LOAD, AS WELL AS HOUR AND DATE ON WHICH EACH LOAD WAS NUMBERS. IDENTIFY ALL RECEPTACLES AND LIGHTING SWITCHES WITH P-TOUCH LABELS SATISFACTION. INTENDED APPLICATIONS, AND TO FIT COPPER CONDUCTORS 10AWG AND LESS. WIRE
PROGRAMMING, CIRCUIT CONTROL, RELAY MODULES, POWER OFF RELAY, WIRING WTC NOT MEASURED, AND VOLTAGE AT TIME OF TEST. INDICATING SOURCE PANEL AND CIRCUIT NUMBERS. 18.2. PROVIDE VIBRATION ISOLATORS IF REQUIRED. CONNECTORS SHALL HAVE THE TEMPERATURE RATINGS EQUAL TO OR GREATER THAN THOSE OF
SPECIFICALLY DESCRIBED BUT REQUIRED FOR THE OPERATION OF THE SYSTEM, MUST BE THE WIRES UPON WHICH USED. USE TYPE AC90 ARMOURED CABLE (BX) OR FLEXIBLE METAL
PROVIDED AND INCLUDED AS PART OF THE BID PRICE. PART B – EXECUTION 9. TEMPORARY POWER 19. MECHANICAL WIRING CONDUIT FOR CONNECTION FROM CEILING BOXES TO LUMINARIES IN ACCESSIBLE CEILINGS AND
9.8. WHENEVER DIFFERENCES OCCUR BETWEEN PLANS AND DIAGRAMS, SCHEMATICS, AND 9.1. PROVIDE TEMPORARY ELECTRICAL POWER FOR THE WORK OF THIS TRADE AND OTHER TRADES 19.1. CONTROL WIRING FOR ALL MECHANICAL EQUIPMENT TO BE SUPPLIED AND INSTALLED BY DIV.15. TO IN STUD PARTITION WALL DEVICES.
BETWEEN SPECIFICATIONS AND DRAWINGS, THE MAXIMUM CONDITION SHALL GOVERN AND THE 1. DEMOLITION WORK AS REQUIRED BY THE GENERAL CONTRACTOR OR THE TENNANT. ALL STARTERS, INCLUDING FAN SWITCHES TO BE SUPPLIED BY DIV.15 AND INSTALLED BY DIV.16 2.12. PROVIDE TECK CABLES WITH COPPER CONDUCTORS, SIZE AS INDICATED. INSULATION: CROSS-
TENDER SHALL BR BASED ON WHICHEVER IS THE GREATER AMOUNT. 1.1. CONTRACTOR TO INCLUDE TENDER PRICE ALL LABOR, MATERIALS, EQUIPMENT AND SERVICES UNLESS OTHERWISE NOTED. DIV.16 TO PROVIDE ALL POWER WIRING AND REQUIRED LINKED POLYETHYLENE XLPE 600V RATING. ARMOUR: GALVANIZED STEEL. OVERALL COVERING:
9.9. CONTRACTOR TO ENSURE THAT ALL ELECTRICAL INSTALLATIONS ARE IN COMPLIANCE WITH ALL NECESSARY AND INDICATE TO COMPLETE ALL THE DEMOLITION AND REMOVAL WORK AS SHOWN 10. LOCATION OF EQUIPMENT AND DISTRIBUTION SYSTEMS DISCONNECT SWITCHES. • THERMOPLASTIC POLYVINYL CHLORIDE COMPLIANT TO BUILDING CODE CLASSIFICATION FOR
AUTHORITIES HAVING JURISDICTION PRIOR TO HANDING WORK OVER TO OWNER. ON DRAWINGS AND AS REQUIRED. DEMOLITION DRAWINGS DO NOT NECESSARILY INDICATE ALL 10.1. LOCATION OF EQUIPMENT AND DISTRIBUTION SYSTEMS INDICATED OR SPECIFIED IS TO BE THIS PROJECT. FASTENINGS: ONE HOLE STEEL STRAPS TO SECURE CABLES 50MM AND
THE CONDITIONS, DETAILS OR WORK REQUIRED. CONTRACTORS SHALL EXAMINE CAREFULLY CONSIDERED AS APPROXIMATE. LOCATE EQUIPMENT AND DISTRIBUTION SYSTEMS TO PROVIDE SMALLER, AND
10. SHOP DRAWINGS THE WORK SITE TO DETERMINE THE ACTUAL CONDITIONS AND EXTENT OF WORK REQUIRED. MINIMUM INTERFERENCE AND MAXIMUM USABLE SPACE AND IN ACCORDANCE WITH PERTINENT • TWO HOLE STEEL STRAPS FOR CABLES LARGER THAN 50MM, CHANNEL TYPE SUPPORTS FOR

ERCA
10.1. SUBMIT SHOP DRAWINGS OF LUMINAIRES, PANELBOARDS AND OTHER MAJOR ELECTRICAL THE CONTRACTORS SHALL REFER 70 THE DESIGN ENGINEER FOR CLARIFICATIONS IF THEY HAVE CODES AND MANUFACTURER’S RECOMMENDATIONS FOR SAFETY, ACCESS AND MAINTENANCE. TWO OR MORE CABLES AT 1.5M CENTERS, AND THREADED RODS 6MM DIAMETER TO SUPPORT
EQUIPMENT, AS REQUESTED BY ENGINEER, UNLESS OTHERWISE NOTED. EACH SHOP DRAWING ANY DETAILS NOT CLEAR PRIOR TO BIDDING, NO ALLOWANCES, WILL BE MADE LATER FOR ANY INFORM THE CONSULTANT OF IMPEDING INSTALLATION AND OBTAIN APPROVAL FOR ACTUAL SUSPENDED CHANNELS. CONNECTORS: WATERTIGHT APPROVED FOR TECK CABLES.
SHALL BE CHECKED AND STAMPED AS BEING CORRECT BY THE GENERAL CONTRACTOR AND EXPENSE INCURRED BY THE CONTRACTOR THROUGH THEIR FAILURE TO MAKE THIS LOCATION.
THE APPROPRIATE TRADE BEFORE SUBMISSION TO THE ENGINEER FOR APPROVAL. EXAMINATION. BEGINNING OF DEMOLITION WORK MEANS CONTRACTOR ACCEPTS EXISTING 10.2. ENSURE MANUFACTURER’S NAMEPLATES, CSA AND/OR ULC LABELS, AND IDENTIFICATION
CONDITIONS. NAMEPLATES ARE VISIBLE AND LEGIBLE AFTER MATERIALS AND EQUIPMENT ARE INSTALLED.
Drawn By Checked By
ai ai
6/1/2020 9:14:52 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

THE INFORMATION INCLUDED IN THIS ELECTRONIC DRAWING FILE IS PROTECTED BY COPYRIGHT. UNAUTHORIZED USE OF THIS FILE WITHOUT THE WRITTEN PERMISSION OF ARCHITECTTURA INC. ARCHITECTS IS PROHIBITED.
ARCHITECTTURA INC. ARCHITECTS IS RESPONSIBLE ONLY FOR INFORMATION SHOWN ON A MECHANICAL REPRODUCTION OF THIS DRAWING FILE THAT HAS BEEN SIGNED AND SEALED BY A REGISTERED ARCHITECT EMPLOYED BY THE FIRM.
THIS DRAWING SHEET IS 36"X24" IN SIZE. IT IS RECOMMENDED THAT ANY REPRODUCTION, ELECTRONIC OR OTHERWISE, BE TO THE SAME SHEET SIZE
TO ENSURE THE ACCURACY OF DRAWING SCALES DEPICTED ON THIS SHEET. THIS DRAWING IS NOT TO BE SCALED - USE FIGURED DIMENSIONS ONLY.
E001
9.11. COMMON TRIP BREAKERS WITH SINGLE HANDLE FOR MULTI-POLE APPLICATIONS
14.8. POWER SUPPLY: UNIVERSAL AC INPUT 120V TO 347V AND DC INPUT 6V TO 24V. EXIT SIGNS
9.12. ALL PANELS TO BE FLUSH OR SURFACE MOUNTED AD INDICATED.
3. CONDUIT AND FITTINGS SHALL BE CONNECTED TO AC NORMAL POWER AND DC POWER SUPPLY FROM AN EMERGENCY
9.13. LOCK-ON DEVICES ON EMERGENCY LIGHTING, NIGHT LIGHTS, SECURITY AND EXIT
3.1. CONDUITS SHALL BE EMT UNLESS NOTED OTHERWISE. BATTERY UNIT.
LIGHT CIRCUITS.
3.2. USE EMT FOR BRANCH CIRCUITS UNLESS NOTED OTHERWISE. 14.9. INSTALLATION: UNIVERSAL MOUNTING TYPE, DIRECTIONAL ARROW(S) AND SINGLE AND/OR
9.14. BREAKERS FOR MOTORS SHOULD BE MOTOR RATED.
3.3. USE PVC CONDUIT FOR EXTERIOR WORK UNLESS NOTED OTHERWISE. DOUBLE FACE AS SHOWN ON DRAWINGS.
9.15. BREAKERS FOR LIGHTING CIRCUITS SHALL BE SWITCH RATED.
3.4. USE LIQUID TIGHT FLEXIBLE CONDUIT FO CONNECTION TO MOTORS. 14.10. SELF-POWERED UNIT IS NOT ACCEPTABLE UNLESS OTHERWISE NOTED.
9.16. BREAKERS FOR TRANSFORMERS SHALL BE TRANSFORMER RATED.
3.5. PROVIDE FLEXIBLE METAL CONDUIT FOR CONNECTION TO TRANSFORMERS, MINIMUM 14.11. ENSURE THAT THE EXIT SIGN CIRCUIT BREAKER IS LOCKED IN “ON” POSITION.
9.17. MANUFACTURER: - FEDERAL PIONEER, SIEMENS, SQUARE D, CUTLER-HAMMER,
1M (3’) LENGTH. 14.12. ALLOW FOR 10% ADDITIONAL EXIT SIGNS TO SUIT THE NEW LAYOUT. SUPPLY AND INSTALL EXIT
WESTINGHOUSE
3.6. USE FLEXIBLE METAL CONDUIT FOR CONNECTION TO RECESSED INCANDESCENT SIGNS IN ACCORDANCE WITH SPECIFICATIONS. CONNECT EXIT SIGNS TO NEAREST AVAILABLE
FIXTURES WITHOUT A PRE-WIRED OUTLET BOX, CONNECTION TO SURFACE FIXTURES, EXIT SIGN CIRCUIT.
10. LUMINAIRES
WORK IN MOVABLE METAL PARTITIONS, OR TRANSFORMERS. 14.13. ALLOW FOR 3 ADDITIONAL EXIT SIGNS AS PART OF PROJECT COMPLETE WITH WIRING BACK TO
10.1. LUMINAIRES GENERAL: INTERNAL LUMINAIRE WIRING, TYPE 105 DEGREE C TEMPERATURE
3.7. FLEXIBLE METAL CONDUIT SHALL BE USED FOR FIXTURES IN FINISHED AREAS ONLY BREAKER / BATTERY AS NOTED ON DRAWINGS. PROVIDE CREDIT IF NOT USED DURING
RATING, MINIMUM CONDUCTOR SIZE OF NO.18 AWG, GREEN GROUND WIRE TO GROUNDING
WHERE CHAIN HANGING IS SPECIFIED. IN THIS CASE THE FLEXIBLE CONDUIT SHALL BE CONSTRUCTION.
SCREW AT FIXTURES. ACCESSORIES: MOUNTING HARDWARE, CEILING TRIM RINGS AND
TIE WRAPPED TO THE CHAIN. 180 Eugenie Street West
PERIMETER FRAMES, END CLOSURE PLATES OR GASKETS, FITTINGS TO ENSURE FIXTURE
3.8. INSTALL CONDUIT AND SLEEVES PRIOR TO POURING OF CONCRETE. SLEEVE 15. FIRE ALARM SYSTEMS Windsor, ON N8X 2X6
CLOSURE, FOR SECURE, ACCURATE AND FLUSH FIT INSTALLATION. 519.258.1390
THROUGH CONCRETE: SCHEDULE 40 STEEL PIPE SIZED FO FREE PASSING OF 15.1. INSTALL FIRE ALARM SYSTEM / COMPONENTS IN ACCORDANCE WITH CSA/ULC-524. ALL NEW
10.2. LOCATE AND INSTALL LUMINAIRES AS INDICATED. ALIGN LUMINAIRES MOUNTED IN CONTINUOUS
CONDUIT, AND PROTRUDING 2” DEVICES SHALL BE FULLY COMPATIBLE WITH AND MATCH THE EXISTING BUILDING’S FIRE
ROWS TO FORM STRAIGHT LINE. ALIGN LUMINAIRES MOUNTED INDIVIDUALLY PARALLEL OR
3.9. IF PLASTIC SLEEVES ARE USED IN FIRE RATED WALLS OF FLOORS, REMOVE BEFORE ALARM SYSTEM. WIRING METHOD SHALL BE AS REQUIRED ON SECTION 32 OF THE ONTARIO
PERPENDICULAR TO BUILDING GRID LINES.
CONDUIT INSTALLATION. ELECTRICAL SAFETY CODE.
10.3. FOR SUSPENDED CEILING INSTALLATIONS, SUPPORT LUMINAIRES INDEPENDENTLY OF CEILING
3.10. INSTALL CABLES, CONDUITS AND FITTINGS TO BE EMBEDDED OR PLASTERED OVER, 15.2. FOR NEW SYSTEMS – PROVIDE UPDATED BATTERY CALCULATIONS AND BATTERY SET AS
IN ACCORDANCE WITH THE ESA’S REQUIREMENTS. INSTALL CABLE DROPS (POWER AND
NEATLY AND CLOSE TO BUILD STRUCTURE SO FURRING CAN BE KEPT TO MINIMUM. REQUIRED PER NEW SIGNAL DEVICES. EMERGENCY POWER BATTERY SET SHALL BE CAPABLE
CONTROL) FOR LUMINAIRES OF SUFFICIENT LENGTH TO ALLOW LUMINAIRE TO BE RELOCATED
3.11. ALL CONDUITS FOR COMMUNICATION WIRING SHALL BE INSTALLED WITH BUSHINGS AT OF PROVIDING SUPERVISORY POWER FOR NOT LESS THAN 24 HOURS AND IMMEDIATELY
TO ANY LOCATION WITHIN 3000 MM RADIUS.
EACH END. CONDUITS SHALL BE TERMINATED ON EQUIPMENT RACK, BACKBOARD OR FOLLOWING, EMERGENCY POWER UNDER FULL LOAD FOR NOT LESS THAN 30 MINUTES.
10.4. ALL LUMINAIRES INSTALLED IN OR ON BASE BUILDING CEILINGS SHALL BE INDEPENDENTLY
CABLE TRAY WITHIN THE ROOM. 15.3. PERFORM VERIFICATION OF NEW INSTALLED AND/OR ALTERED WIRING AND DEVICES IN
SUPPORTED FROM BUILDING STRUCTURE WITH CHAIN UNLESS OTHERWISE NOTED.
3.12. PROVIDE FIRE-PROOFING / SOUND ATTENUATION INSULATION WHEN RUNNING ACCORDANCE WITH REQUIREMENTS OF CSA/ULC-537 AND PROVIDE THE SUBSEQUENT
10.5. ALL EXISTING TO REMAIN AND RELOCATED LUMINAIRES SHALL BE CLEANED OF DUST AND This drawing is not to be used for
CONDUITS CROSSING FIRE-RATED WALL / SOUND BARRIER LOCATIONS. VERIFICATION REPORT. construction unless it is countersigned
DEBRIS AND RELAMPED WITH NEW. PROVIDE 3" MIN. GAP BETWEEN
3.13. PROVIDE VAPOUR SEALING WHEN RUNNING CONDUITS CROSSING FIRE SUPPRESSION 15.4. THE REPORT SHALL ALSO INCLUDE, IF APPLICABLE, DBA LEVELS WITHIN ALL ENCLOSED ROOMS by the Project Architect
10.6. LED LUMINAIRES – PERFORMANCE TESTED IN ACCORDANCE WITH IES LM-79, LM -80, AND L70 CEILING GRID AND BOTTOM OF
BARRIER WALLS / PARTITIONS. AND OPEN AREAS BEING PART OF THIS PROJECT’S SCOPE OF WORK. THE VERIFICATION
LUMEN MAINTENANCE AT 50,000 HOURS OR GREATER CALCULATED PER IES TM-21 HANGERS
3.14. INSTALL CONDUITS TO CONSERVE HEADROOM, PARALLEL AND PERPENDICULAR TO REPORT SHALL BE COMPLETED AND SIGNED BY A CERTIFIED FIRE ALARM TECHNICIAN. Issued For (YYMMDD)
EXTRAPOLATION.
BUILDING LINES. DO NOT CADDIE CLIP CONDUITS TO CEILING HANGERS. PROVIDE 15.5. ALL NEW DEVICES SHALL BE COMPATIBLE WITH EXISTING FIRE ALARM MAIN PANEL AND TENDER 2020.06.01
10.7. DRIVERS MINIMUM 0.9 POWER FACTOR, THD LESS THAN OR EQUAL TO 20%, 0-10 VOLT DIMMING
SEPARATE INDEPENDENT SUPPORTS. ALL EMPTY CONDUITS SHALL BE COMPLETE SYSTEM. ALL DEVICES SHALL BE NEW UNLESS NOTED OTHERWISE.
STANDARD OR ALTERNATIVE PROTOCOL TO SUIT CONTROLS. 5 YEAR WARRANTY, 80 CRI MIN,
WITH NYLON PULL STRING. CAST FITTINGS ARE NOT PERMITTED TO BE USED. 15.6. RETAIN THE SERVICES OF THE EXISTING FIRE ALARM BASE BUILDING CONTRACTOR FOR
LUMINAIRE EFFICIENCY IN ACCORDANCE WITH DLC OR ENERGY STAR.
TESTING/VERIFICATION.
4. DEVICE, PULL AND JUNCTION BOXES 15.7. ALL SMOKE ALARMS NOT CONNECTED TO THE FIRE ALARM SYSTEM SHALL CONFORM TO
11. LAMPS
4.1. ONLY MAIN JUNCTION AND PULL BOXES ARE INDICATED. INSTALL ADDITIONAL PULL LATEST OBC AND ULC REQUIREMENTS, SHALL BE HARD WIRED AND INTERCONNECTED WITHIN
11.1. ALL LUMINAIRES SHALL BE COMPLETE WITH SUITABLE LAMPS AS RECOMMENDED BY
BOXES AND SIZE BOXES IN ACCORDANCE WITH CSA C22.1 SUPPORT BOXES THE SPACE SUCH DETECTION OF SMOKE FOR ONE UNIT WILL CAUSE ALL UNITS WITHIN THE NOTES:
MANUFACTURER. COLOUR TEMPERATURE, BEAM ANGLE, CRI, FROSTED/CLEAR, ETC. SHALL BE
INDEPENDENTLY OF CONNECTING CONDUITS. JUNCTION ANS PULL BOXES SHALL BE SPACE TO ALARM. 1. PROVIDE A DOUBLE 4" DIAMETER J HOOK FOR INSTALLATION OF DATA AND
CONFIRMED WITH ENGINEER AND ARCHITECT/DESIGN CONSULTANT PRIOR TO ORDERING
GALVANIZED SHEET STEEL BOXES COMPLETE WITH CONDUIT KNOCK-OUT TO SUIT 15.8. ALL SMOKE ALARMS SHALL BE INSTALLED COMPLETE WITH VISUAL STROBE NOTIFICATION. TELEPHONE WIRING. J HOOK SHALL BE MOUNTED THROUGH WALL OR WHERE WALL
LAMPS.
INSTALLATION AND SCREW-ON FLAT COVERS. STROBES SHALL BE SYNCHRONIZED IN ACCORDANCE WITH LATEST OBC REQUIREMENTS. IS NOT AVAILABLE HUNG FROM 1/4" ROD TO OWSJ ABOVE. HOOKS SHALL BE ERICO
11.2. LED, COMPACT FLUORESCENT, FLUORESCENT, AND H.I.D. LAMPS SHALL BE GUARANTEED FOR
4.2. PROVIDE ACCESS DOORS, FIRE RATED IF REQUIRED, IN CEILINGS WHERE DEVICE, CADDY CAT64 (OR AS REQUIRED) WITH APPLICABLE MOUNTING ARRANGEMENT.
A PERIOD OF TWELVE MONTHS FROM THE DATE OF ACCEPTANCE.
PULL OR JUNCTION BOXES ARE NOT READILY ACCESSIBLE. 16. COMMUNICATION, TV, DATA, TELEPHONE AND SECURITY SYSTEMS 2. COORDINATE INSTALLATION WITH LOCATION OF OTHER DEVICES WITHIN CEILING
4.3. GANG DEVICE BOXES WHERE WIRING DEVICES ARE GROUPED. PROVIDE 16.1. INSTALL EMPTY COMPLETE RACEWAY SYSTEM FOR COMMUNICATION, TV, DATA, TELEPHONE SPACE.
12. EMERGENCY LIGHTING
COMBINATION BOXES WITH BARRIERS WHERE OUTLETS FOR MORE THAN ONE AND SECURITY AS REQUIRED AND INDICATED. THE RACEWAY SYSTEM TO INCLUDE TERMINAL
12.1. SUPPLY AND INSTALL NEW EMERGENCY LIGHTING COMPLETE WITH BATTERY BACKUP AS
SYSTEM ARE GROUPED. PROVIDE BLANK COVER. CABINETS, OUTLET BOXES, PULL BOXES, COVER PLATES, CONDUIT, SERVICE POLES,
SHOWN.
4.4. PLATES FOR BOXES WITHOUT WIRING DEVICES. POLYPROPYLENE FISH WIRE, AND PLASTIC BUSHING AT EACH CONDUIT END.
12.2. EMERGENCY LIGHTING UNITS SHALL MEET OR EXCEED CSA C22.2 NO 141.
4.5. JUNCTION BOXES AND PULL BOXES SHALL BE SUITABLE FOR SURFACE MOUNTING 16.2. SUPPLY AND INSTALL ALL TELECOMMUNICATION OUTLETS, CABLING AND TERMINATIONS IN
12.3. EMERGENCY LIGHTING UNIT SHALL BE A STANDBY SUPPLY CONSISTING OF A STORAGE
AND BE OF WELDED STEEL CONSTRUCTION WITH SCREW-ON FLAT COVERS. LOCATIONS SHOWN ON DRAWINGS.
BATTERY, CHARGER, AND INTEGRAL ON UNIT LAMPS. THE UNIT SHALL AUTOMATICALLY
4.6. COVERS WITH 1” MINIMUM EXTENSIONS ALL AROUND, FOR FLUSH MOUNTED PULL AND 16.3. ALL IT INSTALLATIONS SHALL BE IN ACCORDANCE WITH THE FOLLOWING STANDARDS:
TRANSFER EMERGENCY LIGHTING LOADS TO THE BATTERY POWER SUPPLY ON AC POWER
JUNCTION BOXES. ONLY MAIN JUNCTION AND PULL BOXES ARE INDICATED. PROVIDE • TORONTO CORPORATE SERVICES INFORMATION & TECHNOLOGY: STANDARDS AND
FAILURE. THE BATTERY SHALL BE RECHARGEABLE HAVING SUFFICIENT CAPACITY TO SUPPLY
BOXES SO AS NOT TO EXCEED 100 FEET OF CONDUIT RUN BETWEEN PULL BOXES. NO PROCEDURES – CABLING STANDARD. ISSUED BY: IT NETWORK SERVICES – VERSION 4.3 –
AND MAINTAIN AT NOT LESS THAN 91% OF FULL VOLTAGE THE TOTAL LOAD OF THE
MORE THAN TWO (2) 90 DEG. BENDS SHALL BE INSTALLED BETWEEN ANY TWO AUG. 25. 2014.

Date
EMERGENCY LIGHTING FOR A SPECIFIED PERIOD OF TIME, BUT IN ANY CASE, NOT LESS THAN 30
ADJACENT PULL BOXES. 17. NAMEPLATE
MINUTES. THE UNIT SHALL SELF-TEST FOR 1 MINUTE EVERY 30 DAYS, 10 MINUTES EVERY SIX
4.7. OUTLET BOXES, CONDUIT BOXES TO CSA C22.2 NO 18-M1987. 17.1. PROVIDE ENGRAVED LAMICOID NAMEPLATE ON ALL MAJOR ELECTRICAL EQUIPMENT IDENTIFYING
MONTHS, AND 30 MINUTES EVERY 12 MONTHS.
4.8. CAST BOXES FOR SURFACE WORK IN FINISHED AREAS. NAME, VOLTAGE, PHASE, CURRENT RATING, “FED FROM__” AND USE. LETTERING SHALL BE
• SUPPLY VOLTAGE: UNIVERSAL AC INPUT 120V TO 347 V, 60HZ.
4.9. INSTALL JUNCTION BOXES AND PULL BOXES IN INCONSPICUOUS BUT ACCESSIBLE MINIMUM ¼” HIGH, WHITE ON BLACK BACKGROUND.
• OUTPUT VOLTAGE: 6 OR 12 OR 24V DC.
LOCATIONS.
• CAPACITY: 36 OR 50 OR 70 WATTS AS REQUIRED FOR NEW AND EXISTING EMERGENCY
4.10. OUTLET BOXES SHALL BE ELECTRO-GALVANIZED STEEL, SIZED AS REQUIRED BY 18. FIRE STOPPING
LIGHTING LOADS.
CODE. PROVIDE EACH LIGHTSWITCH, RECEPTACLE, FIRE ALARM DEVICE AND OTHER 18.1. PROVIDE APPROVED FIRE STOPPING MATERIAL TO MAINTAIN INTEGRITY OF FIRE SEPARATIONS.
• BATTERY: SEALED, MAINTENANCE FREE OR REPLACEMENT FOR 10 YEARS UNDER NORMAL

2134 mm

2134 mm
ELECTRICAL DEVICE WITH AN OUTLET BOX. INSTALL PLUMB AND TRUE. 18.2. MANUFACTURERS: 3M, AD FIRE PROTECTION, HILTI, OR APPROVED EQUAL.
CONDITIONS.

Revision Schedule
84"

84"

84"
4.11. PROVIDE BLANK COVERPLATES FOR BOXES WITHOUT WIRING DEVICES.
• CHARGER: SOLID STATE, MULTI-RATE, VOLTAGE/CURRENT REGULATED, INVERSE
4.12. TWO OR MORE OUTLET BOXES THAT INSTALLED AT THE SAME LOCATION SHALL BE 19. WIRING DEVICES
TEMPERATURE COMPENSATED, SHORT CIRCUIT PROTECTED WITH REGULATED OUTPUT.
GANGED TOGETHER IN THE SAME COVERPLATE UNLESS NOTED OTHERWISE. 19.1. SWITCHES – MANUALLY OPERATED AC SWITCHES TO CSA C22.2 NO 55-M1986. SNAP SWITCHES TO

1194 mm
• UNIT HOUSING: STEEL WITH WHITE FINISH.

1092 mm

Description
1067 mm
• SIGNAL INDICATOR LIGHTS: SOLID STATE, FOR ‘AC POWER ON’ AND ‘HIGH CHARGE’. CSA C22.2 NO 55-M1986.

47"

914 mm
5. HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS 19.2. 15A AND 20A 120V, SINGLE POLE, DOUBLE POLE, THREE-WAY, AND FOUR WAY SWITCHES WITH

43"
42"
• TEST SWITCH: SOLID STATE TRANSFER CIRCUIT TO BATTERY SUPPLY.

36"
5.1. SUPPORT CHANNELS: LENGTH AS INDICATED, U-SHAPED, SIZE 1-3/4” X 1-1/3” BY 1/8” PILOT LIGHTS AND/OR KEY OPERATION AS INDICATED.
• ELECTRICAL CONNECTION: 2M CORD PLUG, TYPE 5-15P. KNOCKOUT FOR CONDUIT

457 mm
THICK, SURFACE MOUNTED OR SUSPENDED AS REQUIRED. 19.3. SWITCHES SHALL BE OF ONE MANUFACTURER THROUGHOUT PROJECT.
CONNECTION.

18"
5.2. ALL SUPPORTING DEVICES, STRUT CHANNEL, THREADED ROD, ANCHORS, SHALL BE 19.4. FINISH COLOUR AS SELECTED BY ARCHITECT. CONFIRM PRIOR TO ORDERING.
• AUTO TEST: INTEGRAL, AUTOMATIC LOAD TEST FOR 1 MIN EVERY MONTH.
OF THE “HOT DIPPED” GALVANIZED TYPE. ELECTROGALVANIZED COMPONENTS WILL 19.5. PROVIDE SPECIFICATION GRADE LOCAL 20A, 120V AND 20A, 347V SWITCHES, AC TYPE WITH
12.4. RECEPTACLE TO WHICH EMERGENCY UNIT IS TO BE CONNECTED SHALL BE NOT MORE THAN
NOT BE ACCEPTED. MATCHING OVER PLATE.
1.5M FROM THE LOCATION OF THE UNIT.
5.3. ALL CONDUITS, PANELS ETC. TO BE SECURELY AND ADEQUATELY SUPPORTED. • 120V – P&S #26021 SERIES, HUBBLE #2121 SERIES
12.5. LAMP HEADS: INTEGRAL ON UNIT DOUBLE HEADS, AND REMOTE DOUBLE HEADS AS INDICATED, MANUAL FIRE ALARM FIRE STROBE AND ABOVE DESK ABOVE COUNTER TYP. ELEC OR DATA THERMOSTAT OUTLETS CLOCK WALL WIRELESS
5.4. WHERE MORE THAN 3 CONDUITS RUN TOGETHER, CONDUIT RACKS TO BE USED. • 347V – P&S #2601 – 347 SERIES
345 DEGREES HORIZONTAL AND 180 DEGREES VERTICAL ADJUSTMENT, SWIVEL TYPE, GLARE PULL STATIONS HORN RECEPTACLES AND RECEPTACLES OUTLET ACCESS POINT
5.5. SINGLE RUNS OF CONDUIT TO BE SUPPORTED BY GALVANIZED CONDUIT STRAPS OR
FREE, SEALED BEAM. LAMPS: LED 4W, MR 16, 200 LUMEN MINIMUM OUTPUT, AND MINIMUM DATA OUTLETS
RING BOLT TYPE HANGERS. 20. TESTING
20, 000 HOURS OF OPERATIONAL LIFE.
5.6. TIE WIRE OR PERFORATED METAL STRAP HANGERS WILL NOT BE ACCEPTED. 20.1. PRIOR TO ENERGIZING ANY NEW WIRING, CONDUCT AN INSULATION RESISTANCE TESTING
12.6. REMOTE LAMP UNITS SHALL BE SUITABLE FOR REMOTE CONNECTION AND SHALL BE INCLUDED
5.7. SUPPORT ALL LUMINAIRES INDEPENDENTLY OF CEILING STRUCTURE. (MEGGER CIRCUITS, FEEDERS AND EQUIPMENT UP TO 350V WITH A 500V INSTRUMENT AND UP TO
IN THE LIST OF LAMP UNITS PROVIDED WITH THE EMERGENCY BATTERY UNIT. THE SIZE OF

No.
5.8. PROVIDE 4” HIGH CONCRETE HOUSEKEEPING PAD FOR FLOOR MOUNTED ELECTRICAL 350-600V WITH A 1000V INSTRUMENT) ON ALL NEW AND EXISTING WIRING AND EQUIPMENT PART OF
CIRCUIT CONDUCTORS FEEDING REMOTE LAMPS SHALL BE SUCH THAT THE VOLTAGE DROPS
DISTRIBUTION EQUIPMENT. THIS PROJECT. TEST AND CHECK THE ELECTRICAL SYSTEMS PERTAINING TO THIS PROJECTOR
DOES NOT EXCEED 5% OF THE UNIT’S OUTPUT VOLTAGE. IDENTIFY CONDUCTORS FOR
THEIR CORRECT OPERATION. PROVIDE TESTING OF NEW EQUIPMENT AND DEVICES, INCLUDING
POLARITY AND VOLTAGE.
6. RECEPTACLES

GENERAL ELECTRICAL NOTES -2

JOG OR PHASE ROTATION TEST AND OTHER TESTS AS RECOMMENDED BY EQUIPMENT
12.7. DIRECT LIGHT HEADS AS REQUIRED.
6.1. DUPLEX RECEPTACLES SHALL BE 120 VOLT, 15 AMP, 5-15R AND SPECIFICATION GRADE MANUFACTURERS TO ENSURE ADEQUATE CONNECTION AND PROPER OPERATION.
UNLESS OTHERWISE NOTED. VERIFY EXACT LOCATION, MOUNTING HEIGHT AND

1829 mm

1829 mm
13. LIGHTING CONTROL DEVICES
COLOUR WITH ARCHITECT/DESIGN CONSULTANT PRIOR TO INSTALLATION.

72"

72"
13.1. SWITCHES AND CONTACTORS SHALL BE SUITABLE FOR LIGHTING LOADS. SWITCHED OF ONE

1524 mm
6.2. RECEPTACLES, PLUGS AND SIMILAR WIRING DEVICES TO CSA C22.2 NO 42-M1984
MANUFACTURER THROUGHOUT PROJECT.

60"
SPECIFICATIONS GRADE.

1092 mm

1092 mm
13.2. SINGLE POLE SWITCHES TO CSA C22.2 NO.111, 120-347 VAC, 15A, TO ACCEPT 10 AWG WIRE
6.3. DUPLEX OR SINGLE RECEPTACLES, CSA TYPE 5-115R, 120V, 15A, U-GROUND WITH THE
SOLID SILVER CONTACTS, AND SUITABLE FOR BACK AND SIDE WIRING.

43"

43"
FOLLOWING FEATURES:
13.3. EXTERIOR LIGHTING CONTROL: PHOTOELECTRIC, SUITABLE FOR WALL OR LUMINAIRE
• SUITABLE FOR #10 AWG FOR BACK AND SIDE WIRING.
MOUNTING AS REQUIRED, CAPABLE OF SWITCHING 1800 WATTS OF LIGHTING LOADS WITH
6.4. BREAK-OFF LINKS FOR USE AS SPLIT RECEPTACLES.
VOLTAGE VARIATIONS OF +/- 10%, ADJUSTABLE SWITCHING TIME DELAY, RATED FOR 5,000
6.5. EIGHT (8) BACK WIRED ENTRANCES, FOUR (4) SIDE WIRING SCREWS.
OPERATIONS, AND PROVISION FOR MANUAL OVERRIDE.
6.6. DOUBLE WIPE CONTACTS, AND RIVETED GROUNDING CONTACTS.
13.4. OCCUPANCY SENSOR: COLOUR WHITE, CEILING OR WALL MOUNT WITH LINE VOLTAGE
6.7. PROVIDE SPECIFICATION GRADE 15A, 120V, “U” GROUND RECEPTACLES, DUPLEX TYPE
CONNECTIONS AND STANDARD RANGE 360 DEGREE OCCUPANCY SENSOR, DUAL-DETECTION
WITH MATCHING COVER PLATES, COLOURED BY ARCHITECT: CIRCUIT BREAKER INDIVIDUAL SAFETY WALL MOUNTED LIGHT SWITCHES INTERCOM WALL PHONE
TECHNOLOGIES BOTH PASSIVE INFRARED (PIR) AND ULTRASONIC, MINIMUM 5M RADIAL
• LEGRAND P&S #26252 SERIES PANEL SWITCHES INDIRECT LIGHT FIXTURE
COVERAGE, TIMER SETTING 30 SECONDS TO 30 MINUTES, LIGHT SENSOR SETTING 20 TO 3000
• HUBBEL #2152 SERIES
LUX, AUTO-ADAPTING AND WALK-THROUGH MODE CAPABILITIES EQUIPPED WITH ADVANCED
• OTHER RECEPTACLES WITH AMPACITY AND VOLTAGE AS INDICATED.
FILTERING TO PREVENT ACTUATION BY NON-OCCUPANT NOISES, AND FULLY COMPATIBLE WITH
6.8. RECEPTACLES OF ONE MANUFACTURER THROUGHOUT PROJECT.
OTHER LIGHTING CONTROL COMPONENTS; FIVE-YEAR WARRANTY.
6.9. INCLUDE FOR 5 ADDITIONAL RECEPTACLES COMPLETE WITH WIRING BACK TO PANEL
13.5. POSITION OCCUPANCY SENSOR TO A MINIMUM 4 FEET FROM NEAREST AIR DIFFUSER, HVAC
AS PART OF THIS PROJECT. CREDIT TO BE PROVIDED IF ADDITIONAL RECEPTACLES ARE NOT USED.
OUTLET, HEATING BLOWERS, ETC.
7. GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS
13.6. CONFIRM INSTALLATION WITH OCCUPANCY SENSOR AND PHOTOSENSOR MANUFACTURER. TYPICAL HEIGHTS
13.7. SUBMIT SHOP DRAWINGS FOR APPROVAL PRIOR TO PLACING ORDER.
7.1. PROVIDE ALL EQUIPMENT GROUNDING AS REQUIRED, REGARDLESS OF WHETHER IT
13.8. PROVIDE STEP DOWN TRANSFORMER AND/OR LOW VOLTAGE CONTROLLER WHERE SENSOR
HAS BEEN SHOWN ON DRAWINGS OR CALLED FOR IN THIS SPECIFICATION.
CONTROLS 347V CIRCUIT.
7.2. ARRANGE GROUNDS SO THAT UNDER NORMAL OPERATING CONDITIONS, NO
13.9. CEILING MOUNTED SENSORS – DUAL TECHNOLOGY – PASSIVE INFRARED (PIR)/ULTRASONIC –
INJURIOUS AMOUNT OF CURRENT WILL FLOW IN ANY GROUNDING CONDUCTOR.
OCCUPANCY SENSOR C/W POWER PACK.
7.3. PROVIDE A GROUND WIRE IN EVERY CONDUIT.
13.10. WALL MOUNTED SENSORS – DUAL TECHNOLOGY – PASSIVE INFRARED (PIR)/ULTRASONIC –
OCCUPANCY SENSOR C/W PUSH BUTTON OVERRIDE.
8. COVERPLATES
13.11. MANUFACTURERS:
8.1. EXPOSED COVERPLATES SHALL BE MADE OF UNBREAKABLE NYLON AND INSTALLED
• WATTSTOPPER DT-355 SERIES OR DW-100 SERIES AS APPLICABLE
AFTER FINAL PAINTING, FLUSH WITH THE WALL. COLOUR TO MATCH DEVICES UNLESS
• HUBBEL EQUAL
OTHERWISE NOTED.
• SENSORSWITCH EQUAL
8.2. COVER PLATES FOR WIRING DEVICES SHALL BE TO SUIT DEVICES.

John R. Park Homestead Heritage Centre

• EATON EQUAL
8.3. COVER PLATES FROM ONE MANUFACTURER THROUGHOUT PROJECT.
• ENSURE VOLTAGE CONTROL MATCHES FIXTURE AS NOTED DRAWINGS.
8.4. SHEET STEEL UTILITY BOX COVER FOR WIRING DEVICES INSTALLED IN SURFACE
13.12. DIMMING SWITCHES – PROVIDE DIMMERS WITH LINEAR SLIDE CONTROLS, AND SIZE TO SUIT

915 County Road 50, Essex, Ontario N0R 1G0

MOUNTED UTILITY BOXES IN SERVICE AREAS.
LOADS CONTROLLED FOR FLUORESCENT, LED, INCANDESCENT, ETC. AS INDICATED.
8.5. STAINLESS STEEL COVER PLATES FOR ALL FLUSH MOUNT BOXES.
13.13. ALL DIMMERS SHALL INCORPORATE AN AIR GAP WHICH SHALL BE ACCESSIBLE WITHOUT
8.6. STAINLESS STEEL COVER PLATES FOR ALL SURFACE MOUNT CAST BASES IN FINISHED
REMOVING THE FACEPLATE.
AREAS.
13.14. DIMMER SHALL MEET UL20 AND UL1472 LIMITED SHORT CIRCUIT TEST REQUIREMENTS FOR
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

8.7. WHERE EXPOSED TO THE WEATHER, COVER PLATES SUITABLE FOR WET LOCATIONS
SNAP SWITCHES.
WHETHER OR NOT A PLUG IS INSERTED INTO THE RECEPTACLE.
13.15. DIMMERS SHOWN SIDE BY SIDE SHALL BE GANGED UNDER ONE SEAMLESS, MULTI-GANG
8.8. MANUFACTURER: - P&S TP 26 SERIES (UNLESS OTHERWISE NOTED)
FACEPLATE.
13.16. DIMMERS SHALL BE RATED 1000W, UNLESS OTHERWISE NOTED.
9. SERVICE EQUIPMENT
13.17. FINISH COLOURED BY ARCHITECT.
9.1. ALL NEW PANELBOARDS, DISCONNECT SWITCHES, BREAKERS, SPLITTERS, ETC. TO BE
13.18. MANUFACTURERS: LUTRON NOVA T SERIES OR APPROVED EQUAL.
OF THE SAME MANUFACTURER. RATING AND TYPE TO COMPLY WITH BASE BUILDING
EQUIPMENT WHERE POSSIBLE. MOLDED CIRCUIT BREAKERS SHALL BE BOLT-ON TYPE.
14. EXIT SIGNS
ALL PANELBOARDS SHALL HAVE LOADS BALANCED ON THE FEEDERS (OPERATIONAL
14.1. EXIT LIGHTS SHALL MEET OR EXCEED CSA C22.2 NO.141-10 AND CSA C860.
AT NORMAL BUSINESS HOURS), ADJUST BRANCH CIRCUITS AS REQUIRED.
14.2. EXIT SIGNS SHALL BE VISIBLE FROM THE EXIT APPROACH AND BE ILLUMINATED
DISCONNECT SWITCHES SHALL BE OF QUICK-MAKE/QUICK-BREAK TYPE.
CONTINUOUSLY.
9.2. PANELBOARDS SHALL BE BUILT TO CSA 22.1NO 29-M1983. 250V PANELBOARDS, BUS
14.3. EXIT SIGNAGE SHALL CONSIST OF A GREEN PICTOGRAM AND WHITE GRAPHIC SYMBOL
AND BREAKERS RATED FOR 10KA ASYMMETRICAL INTERRUPTING CAPACITY, OR AS
MEETING THE VISIBILITY SPECIFICATIONS REFERRED TO IN ISO 3864-1 AND SHALL CONFORM TO
INDICATED.
THE DIMENSIONS INDICATED IN ISO 7010.
9.3. SEQUENCE PHASE BUSSING WITH ODD NUMBERED BREAKERS ON THE LEFT AND EVEN
14.4. ACCEPTABLE PRODUCT: ENERGY STAR QUALIFIED PRODUCT.
ON THE RIGHT, WITH EACH BREAKER IDENTIFIED BY PERMANENT NUMBER
14.5. FRAME AND HOUSING: EXTRUDED OR CAST ALUMINUM WITH BAKED ENAMEL FINISH.
IDENTIFICATION AS TO CIRCUIT NUMBER.
14.6. FACE AND BACKPLATE: MATERIAL AND FINISH TO MATCH HOUSING, AND FACE COMPLETE WITH
9.4. PANELBOARDS: MAINS, NUMBER OF CIRCUITS, AND NUMBER AND SIZE OF BRANCH
ARROWS AS SHOWN ON DRAWINGS.
CIRCUIT BREAKERS AS INDICATED.
14.7. LAMPS: LED TYPE, MINIMUM 50,000 HOURS OF CONTINUOUS OPERATION, AND INPUT POWER OF
9.5. TWO KEYS FOR EACH PANELBOARD AND KEY PANELBOARDS ALIKE.

ERCA
3W OR LESS PER SIGN.
9.6. COPPER BUS WITH FULL SIZE NEUTRAL.
9.7. MAINS SUITABLE FOR BOLT ON BREAKERS.
9.8. FINISH TRIM AND DOOR BAKED GREY ENAMEL.
9.9. MOLDED CASE CIRCUIT BREAKER TO CSA C22.2 NO 5-M1986.
9.10. BOLT-ON MOLDED CASE CIRCUIT BREAKER, QUICK MAKE, QUICK BREAK TYPE FOR
MANUAL AND AUTOMATIC OPERATION WITH TEMP COMPENSATION FOR 40 DEGREE C Drawn By Checked By
AMBIENT.
ai ai
6/1/2020 9:14:53 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0

0.1 0.1 0.1 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.1 fc
0.2 fc 0.1 fc 0.2 fc
0.7 0.7 0.3 0.1 0.1 0.2 0.5 0.6 0.7 0.3 0.1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
180 Eugenie Street West
Windsor, ON N8X 2X6
519.258.1390
8.0 5.6 0.6 0.1 0.1 0.2 1.7 8.0 4.8 0.5 0.1 0.1 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.0 0.0 0.0 0.0 0.0

3 2
16.1
B 6.5 0.6 0.1 0.1 0.2 1.6 17.5
B B 5.2 0.6 0.1 0.1 0.1 0.1 0.1
0.1 0.1 0.2
fc 0.2 0.2 0.2 0.1 0.1 0.1 0.1 0.0 0.0 0.0 0.0

MH: 3.2 MH: 3.2 fc

1.2 1.3 0.5 0.1 0.1 0.3 1.0 1.2 1.4 0.6 0.3 0.2 0.2 0.2 0.2 0.2 0.4 0.5 0.5 0.4 0.2 0.1 0.1 0.1 0.0 0.0 0.0

1.4 1.5 0.5 0.1 0.1 0.3 1.0 1.4 1.6 0.7 0.6 0.6 0.6 0.6 0.4 0.5 0.9 1.6 1.7 1.0 0.4 0.2 0.2 0.1 0.1 0.0 0.0
0.1 fc This drawing is not to be used for
construction unless it is countersigned
19.6 6.1 0.6 0.1 0.1 0.2 1.6 21.7 B
5.3 0.9 1.2 2.9 4.4 1.8 0.2 0.6 1.7 4.0W2 4.1 2.0 0.7 0.4 0.3 0.2 0.1 0.1 0.0 by the Project Architect

4 1 Issued For (YYMMDD)

6.7 B 5.0 0.6 0.1 0.1 0.2 1.7 6.7B 4.8 1.2 2.2 7.5
D13 13
16 0.5 0.4 0.3 0.1 0.1 0.0
11 W1 TENDER 2020.06.01
MH: 3.2 MH: 3.2 Vestibule
15
D15 MH: 7.5
0.6 0.6 0.3
0.1 0.1fc
0.1 0.2 0.6 0.7 1.0 1.1 2.5 8.2 D 1.4 1.1 0.5 0.2
12 MH:
12
12
8 0.20.1fc0.1
D RECEPTION
0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.3 0.5 1.0 2.1 3.7 2.7 0.9 0.3 0.1 0.1
MH: 8
FEMALE W/R
W2
0.0 0.0 0.0 0.0 0.1 0.1 0.1 0.2 0.5 1.2 2.5 4.5
18 3.4 1.1 0.4 0.1 0.1
0.1 fc
W1
0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.6 1.6 4.3W2
MH: 2.0
2.6
7.5 0.8 0.3 0.1 0.1
14
W1 COMMON
0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.6 1.5 3.5 STAIRS TO MEZZANINE 0.9 0.9 0.5 0.2 0.1 0.1
0.2 fc HALLWAY
MH: 7.5

0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.5 1.2 2.2 Office 1.0 1.2 0.7 0.4 0.2 0.1 0.1

0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.5 1.3 2.9 MALE W/R Circulation 2.6 2.2 0.9 0.4 0.2 0.1 0.1

UN WR

Date
0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.6 1.7 4.4W2 4.6
W2 3.7 1.3 0.5 0.2 0.1 0.1
19
0.1 fc
13
W1 ELECT W1 3.0
0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.5 1.4 3.3 CLOSET 4.0 1.2 0.5 0.3 0.1 0.1
MH: 7.5 MH: 7.5

0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.4 0.9 1.4 Servery Storage 2.0 2.0 1.2 0.6 0.3 0.2 0.1

Revision Schedule
0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.5 0.8 0.8 0.4 0.2 0.1
6.8 7.7 7.1 7.3 5.7 3.2 1.8

10.4 11.8 12.0 11.4 8.9 4.9 2.4

0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.3 0.7 1.4 D D 1.2 0.5 0.2
0.20.1fc

Description
11.5 513.2 13.2 12.66 9.9 5.6 2.8

D D
0.0 0.0 0.0 0.0 0.0 0.1
0.10.2fc0.4 1.2 3.3 1.3 0.5 0.2 0.1
11.8 13.4 12.6 12.9 10.1 5.5 3.0
MH: 8 MH: 8
CREATIVE 12.1 13.9 14.0 13.3 10.4 6.0 3.0
W2 COMMONS D D
0.0 0.0 0.0 0.0 0.0 0.1 0.2 0.4 1.4 3.9 15 1.4 0.5 0.2 0.1
12.1 713.8 13.9 13.38 10.4 6.0 3.0
W1
D13.3 12.5 D 10.0 5.5
MH: 7.5 11.7 12.8 2.9
0.0 0.0 0.0 0.0 0.0 0.1 0.1 MH: 8 MH: 8
0.20.3 fc0.9 2.1
11.3 13.0 13.0 12.4 9.7 5.5 2.7
1.3 0.5 0.2 0.1

D D
0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.4 0.8 9.9 911.3 11.4 10.9108.6 4.7 2.2 1.0 0.4 0.2 0.1

5.9
D6.7 6.3 6.5
D 5.1 2.8 1.6
MH: 8 MH: 8

No.
0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.3 0.1 0.3 1.0 2.9 4.8 3.5 1.3 0.4 0.4 3.6 3.7 3.0 1.5 0.6 0.3 0.1 0.1
W2 17
W1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.2 0.1 0.3 0.8 1.9 MH: 2.2
3.1 7.5 1.0 0.4 0.6 0.7 0.7 0.6 0.5 0.3 0.2 0.1 0.1

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.1 0.2 0.4 0.7 1.0 0.8 0.5 0.3 0.2 0.2 0.2 0.2 0.2 0.1 0.1 0.1 0.0

0.2 fc
0.1 fc

SITE PLAN - PHOTOMETRIC

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.1 0.2 0.3 0.3 0.3 0.2 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.0

John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

ERCA
Drawn By Checked By
ai ai
6/1/2020 9:14:54 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

180 Eugenie Street West

Windsor, ON N8X 2X6
B B 519.258.1390

E015 E015 - TELEPHONE CABLE - U6 PAIR PE-89 POWER CABLE

OR EQUICALENT INSIDE 21MM PVC
CONDUIT SCHEDULE 80.
CHECK WITH SERVICE PROVIDER LIGHTING CABLE
BEFORE ORDERING THE CABLE.
- TO TELPHONE DISTRIBUTION BOX
CABLE SIZE: 4 # 3/0 AWG COPPER RW90 -XLPE IN THE PARKING ENTRANCE TELEPHONE CABLE This drawing is not to be used for
IN 53MM (2") PVC CONDUIT SCHEDULE 80. construction unless it is countersigned
LP : 9
LP : 9
FROM HYDRO-1 POLE TO THE STORAGE ROOM by the Project Architect
CABLE TRENCH DEPTH 600 MM
Issued For (YYMMDD)
TENDER 2020.06.01

TO HYDRO-1 POLE

LP : 9

B LP : 9 B LP : 9 LP : 9
W2
WP/GFCI
E015 E015

LP : 9

LP : 9
WP/GFCI

Date
W2

Revision Schedule

Description
W2

LP : 9
TO TELEPHONE BOX (TB)

FROM HYDRO-1 POLE TO THE STORAGE ROOM

IN MEZZANINE

Cable Size: 4 # 3/0 AWG COPPER RW90 -XLPE

LP : 9

WP/GFCI

IN 53MM (2") PVC CONDUIT SCHEDULE 80.

No.
CABLE TRENCH DEPTH 600 MM.
LP : 9

SITE PLAN - POWER & LIGHTING

W2 W2

WP/GFCI
REFER TO KEY NOTES
ON SHEET E301 GROUND ROD

E011
E014
E013 Tr
LP

E012
WP/GFCI

LP : 9
4 # 3/0 AWG COPPER RW90 -XLPE
IN 53MM (2") PVC CONDUIT SCHEDULE 80.

D D

John R. Park Homestead Heritage Centre

LP : 9

915 County Road 50, Essex, Ontario N0R 1G0

W2 D D
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

LP : 9
LP : 9

D D
LP : 9

WP/GFCI LP : 9
LP : 9
W2

ERCA
Drawn By Checked By
N ai ai
6/1/2020 9:14:55 AM

Project No
SITE PLAN - LIGHTING & POWER & TELEPHONE
SCALE: 1 : 75 2020
THIS LINE IS 4" LONG
Sheet No

W2
1 180 Eugenie Street West
Windsor, ON N8X 2X6
1 8TN
LP : 9 519.258.1390

D OS
C
D
AP16

EM2
LP : 9 NOTE: -- OS LP : 6

LP : 1 MH: 12FT
D
D
LP : 15
This drawing is not to be used for
construction unless it is countersigned
LP : 10 LP : 10 3 by the Project Architect

R R AP16 EM1

EM1
LP : 19
Issued For (YYMMDD)
LP : 19 TENDER 2020.06.01
MH: 12FT
LP : 9 W2
OS 5S LP : 15
LP : 10 LP : 10
EM1
R R LP : 19
2

OS AP16
W1
W2 LP : 9 MH: 12FT
LP : 10 EM1 LP : 15
LP : 19
LP : 14 8TN
S8
R

5S
EM3
LP : 6

EM3
LP : 14

LP : 6
LP : 6 EM3 MH: 17FT
R OS
LP : 8
3 EM1
2 LP : 19
W1 LP : 3 AP4
MH: 17FT
2 LP : 14
AP4 R R
LP : 3

Date
LP : 3
MH: 12FT 3 8TN
LP : 14 LP : 14 LP : 3
LP : 8
EM1 OS
OS R R R LPR: 3
LP : 19 S8
5S OS EM1 LP : 19 AP4
MH: 17FT
LP : 15
LP : 19 EM1 2S
MH: 17FT
LP : 19 LP : 18
LP : 14 LP : 14 LP : 18
EM1

Revision Schedule
LP : 19

W2 LP : 9
R R R R LP : 9 W2 LP : 8
LP : 8
2S

Description
AP4
8TN
. LP : 18
W1
AP4 MH: 17FT
LP : 4 LP : 4
LP : 19 EM1 S8
R R EM1 MH: 12FT LP : 19
MH: 17FT
E023 LP : 18 2S

T
3 3 2S
LP : 4 OS LP : 4 S S S
LP : 8
R R LP : 18 LP : 18 EM1 LP : 8

EM3 LP
EM1 LP : 19

No.
LP : 6
3 LP : 9
OS LP : 19 OS
C C
8TN
AP26
MH: 12FT D D
EM1 LP : 19

LP : 20
LP : 9 LP : 9

LIGHTING FLOOR PLAN

EM2

W2 LP : 9
AP26 LP : 6
D D
MH: 12FT

LP : 20
LP : 9 LP : 9

AP26
MH: 12FT D D

EM1
LP : 19
LP : 9
N
W2 MEZZANINE - LIGHTING - NEW

John R. Park Homestead Heritage Centre

N SCALE: 1 : 75

FIRST FLOOR - LIGHTING - NEW

915 County Road 50, Essex, Ontario N0R 1G0

SCALE: 1 : 75

H
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

LIGHTING NOTES - NEW WORK:

1. PROVIDE LED LIGHT FIXTURES & CONTROL SWITCHES AS SHOWN ON THE DRAWING AND LIGHTING FIXTURE
SCHEDULE.

2. CONNECT ALL EXTERIOR WALL LIGHTS, EXTERIOR CANOPY LIGHTS, AND EXTERIOR BOLLARD LIGHTS TO THE SAME CIRCUIT
AS SHOWN ON SHEET E102 . PROVIDE NEW ELECTRONIC ASTRONOMIC 7 DAY TIME SWITCH. INTERMATIC MN: ET8000.

3. PROVIDE SURFACE MOUNTED CONDUITS FOR PENDANT LIGHTING AND CEILING FANS. CONDUITS AND CONDUIT SADDLES SHALL
BE PAINTED PRIOR INSTALLATION WITH THE SAME COLOUR OF THE WOODEN TRUSSES AND BEAMS.
PAINTING OF THE CONDUITS & SADDLES BY GENERAL CONTRACTOR. ELECTRICAL CONTRACTOR TO COORDINATE THIS WORK
WITH GENERAL CONTRACTOR

ERCA
4. ALL AFOREMENTIONED WORKS ARE FULLY INCLUSIVE IN THE SCOPE OF WORK
WITHOUT ANY EXTRA COST TO THE OWNER.

Drawn By Checked By
ai ai
6/1/2020 9:14:58 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

TYPE DESCRIPTION & MODEL NO. THUMBNAIL MANUFACTURER LED OUTPUTS MOUNTING LOCATION
120 V, 2 A Maestro switch with XCT, PIR occupancy
2S and vacancy sensor, no neutral wire, single-pole.
S1 S Toggle on and off with auto on/off. One gang backbox
2X2 LED RECESSED LIGHT FIXTURE COOPER OR 26.7 WATT LED RECESSED 1ST FLOOR
R 120V, 3000K VERIFY EXACT MS-OPS2-WH This drawing is not to be used for
APPROVED EQUIVALENT OFFICE -WASHROOMS Manufacturer : LUTRON or equivalent
22CZ2-32-UNV-L830-CD1-U 3261 LUMEN HEIGHT SURVERY
construction unless it is countersigned
by the Project Architect

Issued For (YYMMDD)

2 Button with Light Icon - Pico Keypad
2 TENDER 2020.06.01
S2 S
LED 4FT STRIP LIGHT FIXTURE 32.9 WATT LED SURFACE, STRIP
120V, 3000K CEILING MOUNT 1ST FLOOR PJ2-2B-GWH-L01 (CW-1-WH)
COOPER OR STORAGE ROOM Manufacturer : LUTRON or equivalent
S 4SNLED-LD5-33SL-LW-UNV-L830-CD1-U 3290 LUMEN VERIFY EXACT
APPROVED EQUIVALENT
HEIGHT
61.16 WATT LED PENDANT, STRIP
S8 8TSNLED-LD5-74SL-LW-UNV-L830-CD1-U 120V, 3000K CEILING MOUNT MEZZANINE
7164 LUMEN @ 17FT AFF
3 Button with Raise/Lower and Light Icon - Pico Keypad
S3 3S
LED VANITY LIGHT FIXTURE PJ2-3BRL-GWH-L01 (CW-1-WH)
31.7 WATT LED WALL MOUNT Manufacturer : LUTRON or equivalent
W1 DALS OR WASHROOMS
120V, 3000K @ 6FT AFF
LEDVAN002-36 APPROVED EQUIVALENT 2063 LUMEN

LED LINEAR PENDANT LIGHT FIXTURE

Electronic 7 Day Astronomical In Wall Timer - White
S8 S
AP4 APCxDD30x04x[F1_F2_E1_E2_E3_E4]M 34.11W/120V/4438L/3000K PENDANT, LINEAR T Part Number: EI600WC

Date
CEILING MOUNT. Manufacturer : Intermatic or equivalent
FLUXWERX OR RECEPTION, CLASSROOM
REFER TO
APPROVED EQUIVALENT 137W/120V/4438L/3000K & MEZZANINE
AP16 APCxDD30x16x[F1_F2_E1_E2_E3_E4]M MOUNTING
HEIGHT ON THE
DRAWING
AP26 APCxDD30x26x[F1_F2_E1_E2_E3_E4]M 222W/120V/4438L/3000K

Radio Powr Savr Wireless Ceiling Occupancy Sensor

Revision Schedule
S4 OS
LRF2-OCR2B-P
LED RECESSED LIGHT FIXTURE Manufacturer : LUTRON or equivalent
D 14.39 WATT LED RECESSED EXTERIOR CANOPYS

Description
COOPER OR 120V, 3000K VERIFY EXACT
LD4B15D010-EU4B10208030-4LBDW1H AND VESTIBULE
APPROVED EQUIVALENT 1291 LUMEN HEIGHT

Radio Powr Savr Wireless Corner Occupancy Sensor

C
S5 OS
LRF2-OKLB-P-WH
Manufacturer : LUTRON or equivalent
LED EXTERIOR WALL LIGHT FIXTURE 15.5 WATT LED WALL MOUNT
W2 COOPER OR 120V, 3000K @ 7.5FT AFF EXTERIOR WALLS
303-W1-LEDB2-3000-UNV-T2-DIM10-CS APPROVED EQUIVALENT 1069 LUMEN

120/277-Volt AC Energi TriPak® PowPak®

No.
S6 5S
RMJS-5R-DV-B
Manufacturer : LUTRON or equivalent

LED BOLLARD LIGHT 23 WATT LED CONCRETE

B BEGA OR 120V, 3000K BASE MOUNT EXTERIOR WALLWAY
BEGA 84_061_K3 APPROVED EQUIVALENT 1374 LUMEN
Vive PowPak 120/277V, 8A, 0-10V Dimming Module

LIGHT FIXTURES & LIGHT

S7 8TN
RMJS-8TN-DV-B
Manufacturer : LUTRON or equivalent

CONTROL SCHEDULES
EMERGENCY BATTERY UNIT C/W 6V, 36W WATT
WALL MOUNT AS INDICATED ON THE
EM1 DOUBLE LED HEADS BEGHELLY-GALAXY BATTERY: 120V INPUT
@ 8FT AFF LIGHTING PLAN
OR EQUIVALENT AND TWO 7W, MR16,
G6-BTMR2-7W-NC LED LAMPS TYPICAL LIGHTING CONTROL NOTES

1. LIGHTING CONTROL SYSTEM SHOWN ON THE LIGHTING PLAN IS PROVIDED FOR CONCEPTIONAL PURPOSE ONLY, AND IS NOT
INTENDED FOR CONSTRUCTION. EXACT EQUIPMENT REQUIREMENTS, INCLUDING LOCATIONS AND QUANTITIES SHOULD BE
VERIFIED IN ACCORDANCE WITH THE MOST UP-TO-DATE LIGHTING & POWER PLANS, LIGHT FIXTURE SCHEDULES, PANEL
COMBO EXIT SIGN WITH LED DOUBLE SCHEDULES AND SPECIFICATIONS.
6V, 36W WATT WALL MOUNT
HEAD EMERGENCY LIGHT C/W BEGHELLI OR BATTERY: 120V INPUT AS INDICATED ON THE
RUNNING MAN FACE VERIFY EXACT 2. CONTRACTOR SHALL COORDINATE THE LIGHTING CONTROL INSTALLATION WITH THE MANUFACTURER SPECIALIST PRIOR
EM2 EQUIVALENT AND TWO 7W, MR16, LIGHTING PLAN
HEIGHT STARTING THE WORK.
LED LAMPS
SL-RM-6-36-L-1-OLR-M-2BTMR-LEDMR16-7W
3. CONTRACTOR SHALL LOCATE, INSTALL AND WIRE THE EQUIPMENT ACCORDING TO MANUFACTURER INSTALLATION
AND SPECIFICATION DOCUMENTS.

RUNNING MAN LED SIGN 4. CONTRACTOR TO UTILIZE THE SAME WIRING AND MOUNTING DEVICES ACCORDING TO THE MANUFACTURER REQUIREMENT.
EMERGENY LIGHT FIXTURE WITH WALL MOUNT. AS INDICATED ON THE
EM3 120MIN BATTERY BACK-UP AMILITE OR 2 WATT LED VERIFY EXACT 5. CONTRACTOR SHALL EMPLOY THE PROGRAMMING AND COMMISSIONING OF THE LIGHTING CONTROL SYSTEM TO THE
LIGHTING PLAN
APPROVED EQUIVALENT 120V LOCATION MANUFACTURER AND ENSURE THAT THE SYSTEM FUNCTIONALITY MEETS THE DESIGN INTENT.
RPST1MWHT-BAT1/AT/K5
6. CONTRACTOR SHALL PROVIDE TRAINING DEMO TO THE OWNER.

John R. Park Homestead Heritage Centre

7. CONTRACTOR SHALL PROVIDE 2-YEAR SYSTEM WARRANTY PROVIDING 100% REPLACEMENT PARTS & LABORS.

915 County Road 50, Essex, Ontario N0R 1G0

NOTES:
8. ALL AFOREMENTIONED WORKS ARE FULLY INCLUSIVE IN THE SCOPE OF WORK WITHOUT ANY EXTRA COST TO THE OWNER.
1. ALL LIGHT FIXTURES SHALL BE APPROVED BY OWNER/CONSULTANT PRIOR ORDERING.
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

2. FOR EXACT LOCATIONS OF RECESSED LIGHTING FIXTURES, SEE ARCHITECTURAL REFLECTED CEILING PLANS. COORDINATE INSTALLATION OF LIGHTING FIXTURES WITH LOCATION OF
EQUIPMENT, PIPING & DUCT WORKS.

3. REFER TO MANUFACTURER FOR INSTALLATION METHODS PRIOR QUOTING.

4. CONTRACTOR SHALL PROVIDE AND INSTALL ALL HANGING HARDWARE MATERIAL, AIRCRAFT CABLES, CONNECTORS, ACCESSORIES, GRID LOCKING CLIPS, AND SUSPENSION CLIPS
REQUIRED FOR THE LIGHT FIXTURES, AS PER MANUFACTURER REQUIREMENT AND COMPLETE THE WORK AT THE SATISFACTION OF OWNER.

5. EQUIVALENT MANUFACTURERS ARE ACCEPTABLE, PROVIDED THAT SUGGESTED MODELS WILL MAINTAIN THE MINIMUM LUX REQUIREMENTS, AS PER ILLUMINATING ENGINEERING
SOCIETY ( IES) RECOMMENDATIONS.

ERCA
Drawn By Checked By
ai ai
6/1/2020 9:14:59 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No

RF RF
RF LRF2-OCR2B-P-WH (S4) LRF2-OCR2B-P-WH (S4)
RF LRF2-OKLB-P-WH (S5) 1ST FLOOR - MALE WASHROOM 1ST FLOOR - FEMALE WASHROOM
LRF2-OKLB-P-WH (S5) 1ST FLOOR - RECEPTION RF CEILING OCCUPANCY SENSOR RF CEILING OCCUPANCY SENSOR
180 Eugenie Street West
1ST FLOOR - CREATIVE COMMONS RF WALL CORNER OCCUPANCY SENSOR Windsor, ON N8X 2X6
RF WALL CORNER OCCUPANCY SENSOR 519.258.1390

RF
LRF2-OKLB-P-WH (S5)
1ST FLOOR - RECEPTION
RF WALL CORNER OCCUPANCY SENSOR

RF RF
LRF2-OCR2B-P-WH (S4) LRF2-OCR2B-P-WH (S4)
RF 1ST FLOOR - MALE WASHROOM 1ST FLOOR - FEMALE WASHROOM This drawing is not to be used for
LRF2-OKLB-P-WH (S5) RF RF CEILING OCCUPANCY SENSOR RF CEILING OCCUPANCY SENSOR construction unless it is countersigned
by the Project Architect
1ST FLOOR - CREATIVE COMMONS
PJ2-3BRL-GWH-L01 | CW-1-WH (S3)
RF WALL CORNER OCCUPANCY SENSOR
1ST FLOOR - RECEPTION Issued For (YYMMDD)
3 BUTTON WITH RAISE/LOWER AND LIGHT ICON - PICO KEYPAD TENDER 2020.06.01
SCENES 1-2 + OFF WITH RAISE/LOWER
1 GANG BACKBOX

RF
PJ2-3BRL-GWH-L01 | CW-1-WH (S3)
RF 1ST FLOOR - RECEPTION RF
PJ2-3BRL-GWH-L01 | CW-1-WH (S3) 3 BUTTON WITH RAISE/LOWER AND LIGHT ICON - PICO KEYPAD PJ2-2B-GWH-L01 | CW-1-WH (S2) RF
1ST FLOOR - CREATIVE COMMONS SCENES 1-2 + OFF WITH RAISE/LOWER 1ST FLOOR - MALE WASHROOM PJ2-2B-GWH-L01 | CW-1-WH (S2)
3 BUTTON WITH RAISE/LOWER AND LIGHT ICON - PICO KEYPAD 1 GANG BACKBOX 2 BUTTON WITH LIGHT ICON - PICO KEYPAD 1ST FLOOR - FEMALE WASHROOM
SCENES 1-2 + OFF WITH RAISE/LOWER SCENE 1 + OFF 2 BUTTON WITH LIGHT ICON - PICO KEYPAD
1 GANG BACKBOX 1 GANG BACKBOX SCENE 1 + OFF
RF 1 GANG BACKBOX
LRF2-OKLB-P-WH (S5)
1ST FLOOR - CORRIDOR
RF WALL CORNER OCCUPANCY SENSOR
120V 120V 120V 120V

Date
RF RF RF RF

RMJS-8TN-DV-B (S7) RMJS-8TN-DV-B (S7) RMJS-5R-DV-B (S6) RMJS-5R-DV-B (S6)

1ST FLOOR - CREATIVE COMMONS 1ST FLOOR - RECEPTION 1ST FLOOR - MALE WASHROOM 1ST FLOOR - FEMALE WASHROOM
PowPak DIMMING MODULE WITH PowPak DIMMING MODULE WITH PowPak RELAY MODULE PowPak RELAY MODULE
0-10 V CONTROL 0-10 V CONTROL

Revision Schedule

Description
1ST FLOOR - COMMON HALLWAY 1ST FLOOR - OFFICE 1ST FLOOR - SURVERY 1ST FLOOR - VESTIBULE

RF RF RF RF
LRF2-OCR2B-P-WH (S4) LRF2-OCR2B-P-WH (S4) LRF2-OKLB-P-WH (S5) LRF2-OCR2B-P-WH (S4)
1ST FLOOR - COMMON HALLWAY 1ST FLOOR - OFFICE 1ST FLOOR - SURVERY 1ST FLOOR - VESTIBULE
RF CEILING OCCUPANCY SENSOR RF CEILING OCCUPANCY SENSOR RF CEILING OCCUPANCY SENSOR

No.
RF WALL CORNER OCCUPANCY SENSOR

RF
PJ2-2B-GWH-L01 | CW-1-WH (S2) RF RF
1ST FLOOR - COMMON HALLWAY PJ2-3BRL-GWH-L01 | CW-1-WH (S3) PJ2-3BRL-GWH-L01 | CW-1-WH (S3)
2 BUTTON WITH LIGHT ICON - PICO KEYPAD 1ST FLOOR - OFFICE 1ST FLOOR - SURVERY
SCENE 1 + OFF 3 BUTTON WITH RAISE/LOWER AND LIGHT ICON - PICO KEYPAD 3 BUTTON WITH RAISE/LOWER AND LIGHT ICON - PICO KEYPAD

LIGHTING CONTROL
1 GANG BACKBOX SCENES 1-2 + OFF WITH RAISE/LOWER SCENES 1-2 + OFF WITH RAISE/LOWER
1 GANG BACKBOX 1 GANG BACKBOX

120V 120V 120V 120V

SCHEMATICS
RF RF RF RF

RMJS-5R-DV-B (S6) RMJS-8TN-DV-B (S7) RMJS-8TN-DV-B (S7) RMJS-8TN-DV-B (S7)

1ST FLOOR - COMMON HALLWAY 1ST FLOOR - OFFICE 1ST FLOOR - SURVERY 1ST FLOOR - VESTIBULE
PowPak RELAY MODULE PowPak DIMMING MODULE WITH PowPak DIMMING MODULE WITH PowPak DIMMING MODULE WITH
0-10 V CONTROL 0-10 V CONTROL 0-10 V CONTROL

John R. Park Homestead Heritage Centre

915 County Road 50, Essex, Ontario N0R 1G0

1ST FLOOR - STORAGE 1ST FLOOR - UN WASHROOM MEZZANINE OPEN MEZZANINE MECH RM
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

RF
LRF2-OKLB-P-WH (S5)
1ST FLOOR - MEZZANINE WIRED CONNECTION
RF WALL CORNER OCCUPANCY SENSOR

120V 120V 120V 120V

MS-OPS2-WH | CW-1-WH (S1) MS-OPS2-WH | CW-1-WH (S1) MS-OPS2-WH | CW-1-WH (S1)

1ST FLOOR - STORAGE. 1ST FLOOR - UN WASHROOM. 1ST FLOOR - MEZZANINE MECH RM.
120 V, 2 A MAESTRO SWITCH 120 V, 2 A MAESTRO SWITCH 120 V, 2 A MAESTRO SWITCH RF CONNECTION
WITH XCT, PIR OCCUPANCY WITH XCT, PIR OCCUPANCY WITH XCT, PIR OCCUPANCY
AND VACANCY SENSOR, AND VACANCY SENSOR, AND VACANCY SENSOR,
RF
NO NEUTRAL WIRE, NO NEUTRAL WIRE, NO NEUTRAL WIRE,
SINGLE-POLE. SINGLE-POLE. PJ2-3BRL-GWH-L01 | CW-1-WH (S3) SINGLE-POLE.

ERCA
TOGGLE ON AND OFF WITH TOGGLE ON AND OFF WITH 1ST FLOOR - MEZZANINE TOGGLE ON AND OFF WITH
AUTO ON/OFF. ONE GANG AUTO ON/OFF. ONE GANG 120V 3 BUTTON WITH RAISE/LOWER AND LIGHT ICON - PICO KEYPAD AUTO ON/OFF. ONE GANG
BACKBOX BACKBOX SCENES 1-2 + OFF WITH RAISE/LOWER BACKBOX
1 GANG BACKBOX
RF
Drawn By Checked By

RMJS-8TN-DV-B (S7) ai ai
6/1/2020 9:14:59 AM

1ST FLOOR - MEZZANINE Project No

PowPak DIMMING MODULE WITH
0-10 V CONTROL 2020
THIS LINE IS 4" LONG
Sheet No

LP- 24
E001

LP- 24
E005
E019 E019
LP- 34 E003 PROVIDE ROUGH-IN AND WIRING FOR THE HVAC THERMOSTAT. COORDINATE THE REQUIREMENT WITH MECHANICAL
CONTRACTOR. THERMOSTAT PROVIDED BY MECHANICAL CONTRACTOR. Tr 112.5 KAV, 3PH, 600/208V, 60HZ, 4W DRY POWER TRANSFORMER
LP- 13 1
E004 CONNECT THE EXHAUST FAN THROUGH THE LIGHTING SENSOR SWITCH. COORDINATE THE POWER CONNECTION WITH 180 Eugenie Street West
Windsor, ON N8X 2X6
MECHANICAL CONTRACTOR. M 519.258.1390
E005 PROVIDE HDMI CONNECTION CABLE FROM FLOOR BOX NUMBER-1 TO THE WALL HDMI OUTLET NEXT TO THE LED TV. 7-JAW KWH METER - HYDRO STANDARD
LP- 22 E009
PTO PTO PTO E006 PROVIDE TWO HDMI CONNECTION CABLES FROM FLOOR BOXES NUMBER 2&3 TO THE WALL HDMI OUTLET NEXT TO THE
LED TV.
WP/GFCI

PTO
MH: 20FT 20 AMP 120V-3 WIRE GROUNDED DUPLEX
LP- 2 E007 PROVIDE TYPICAL BARRIER FREE RESTROOM CONTROL KIT C/W DOOR OPERATOR AS INDICATED ON SHEET E303. RECEPTACLE CSA 5-20R - TAMPER RESISTANT
LP- 10 E002
LP- 26 E008 FUTURE ELEVATOR. PROVIDE ROUGH-IN CONDUITS & BOX WITH BLANK COVER PLATE FROM ELECTRICAL PANEL TO
E004 THE JUNCTION BOX. USE CONDUIT SIZE 21 MM. 20 AMP 120V-3 WIRE GROUNDED DUPLEX RECEPTACLE
LP- 28
E009 PROVIDE INDOOR COMMERCIAL CEILING FAN. REFER TO THE TECHNICAL DETAILS ON THE ELECTRICAL LEGEND. CSA 5-20R-GROUND FAULT CIRCUIT INTERRUPTED DEVICE
GFCI
LP- 28 TYPICAL HEIGHT IS 20 FT.
OPEN AREA E011 PROVIDE 112.5 KAV, 3PH, 600/208V, 60HZ, 4W DRY POWER TRANSFORMER. 20 AMP, GFCI, DUPLEX RECEPTACLE, WEATHER PROOF, This drawing is not to be used for
construction unless it is countersigned
E012 PROVIDE 200A, 7-JAW SOCKET FOR KWH METER. WITH IN-USE COVER, AS SHOWN ON THE DRAWING. by the Project Architect
WP/GFCI
E013 PROVIDE 100A SAFETY DISCONNECT SWITCH WITH 70A FUSES, 600V, 3P, 3 FUSES, 4W,TYPE 1. MODEL NO. HFC363.
LP- 32 LP- 33
BRAND: SIEMENS OR APPROVED EQUIVALENT. Issued For (YYMMDD)
D D E014 PROVIDE GROUNDING SYSTEM/GROUNDING ELECTRODES AS INDICATED ON SHEET E303. 50 AMP 240 VOLTS 4 WIRE STOVE RECEPTACLERECEPTACLE
S TENDER 2020.06.01
E015 PROVIDE CONCRETE FOUNDATION FOR EACH BOLLARD LIGHT. REFER TO BOLLARD LIGHT MOUNTING DETAIL ON SHEED
E303.
DISHWASHER - 20 AMP 120V-3 WIRE GROUNDED DUPLEX
ELECTRIC RADIANT HEATERS E016 PROVIDE IT ENCLOSURE RACK C/W COOLING FAN & LOCKABLE LATCH HANDLE & 8WAY PDU. BRAND: SYSRACKS, RECEPTACLE CSA 5-20R - TAMPER RESISTANT
LP- 28
DIMENSIONS: 12U 24"X35"X25". D
E017 PROVIDE 24 GIGABIT POE PORTS ETHERNET SWITCH MOUNTED INSIDE THE IT ENCLOSUER RACK. ALL DATA &
TELEPHONE CABLES SHALL BE CAT6 ROUTED IN 21MM CONDUITS. THE CONTRACTOR TO FASTEN AND TERMINATE THE MICROWAVE - 20 AMP 120V-3 WIRE GROUNDED DUPLEX
LP- 21 LP- 21
CABLES FROM BOTH END AND COMMISSION THE DATA & TELEPHONE SYSTEM AT THE SATISFACTORY OF THE OWNER. M RECEPTACLE CSA 5-20R - TAMPER RESISTANT
E017
LP- 27 E018 PROVIDE TELEPHONE CABINET. BRAND: EATON, TYPE 3R OR APPROVED EQUIVALENT. FLOOR MOUNTED BOX CONTAINS QUAD POWER RECEPTACLE,
LP- 5 LP- 54 TC E019 PROVIDE TYPICAL BARRIER FREE DOOR ACCESS CONTROL KIT C/W DOOR OPERATOR AND PUSH TO OPEN BUTTONS AS DUPLEX DATA OUTLET AND DUPLEX HDMI OUTLET
SHOWN ON SHEET E301. CONNECTED TO THE TV'S
E018
LP- 27
E020 DIRECT POWER CONNECTION POINT FOR THE ERV.REFER TO HVAC DRAWING. COORDINATE THE POWER CONNECTION
LP- 26 E016
WITH MECHANICAL CONTRACTOR.

WP/GFCI
LP- 27 AHU-2 IT RACK 1P, 120V - DIRECT CONNECTION TO AN ELECTRICAL DEVICE
LP- 27 AHU-3 LP- 54
E022 PROVIDE SINGLE DATA OUTLET FOR WIRELESS ACCESS POINT CONNECTION.
D D
E023 PROVIDE INTERMATIC ELECTRONIC 7 DAY ASTRONOMICAL IN WALL TIMER FOR THE EXHAUST FAN IN STORAGE ROOM.
WAP

LP- 56 LP- 46 E022 LP- 17 SET THE TIMER ON/OFF EVERY 6 HOURS. 1P, 120/208V - DIRECT CONNECTION TO AN ELECTRICAL DEVICE
LP- 22 E009 E024 CONNECT THE EXHAUST FAN TO A DEDICATED ELECTRONIC 7 DAY ASTRONOMICAL IN WALL TIMER. THE TIMER SWITCH
LP- 28
LP- 27 LP- 27 LP- 38,39 IS SHOWN ON THE LIGHTING PLAN. REFER TO SHEET E201.
LP- 38,39
E025 GFCI RECEPTACLE FOR WATER REFILLING STATION. WEATHER PROOF 3P, 100A DISCONNECT SWITCH
MH: 20FT E026 PROVIDE POWER CONNECTION FOR ELECTRICAL DUCT HEATER.COORDINATE WITH MECHANICAL CONTRACTOR.

Date
D E026
ELECTRICAL
LP- 24

ESS
LP- 38,39
LP- 57 DUCT LP- 47,48
LP- 17 2P, 30A DISCONNECT SWITCH
ESS HEATER E020

PTO
E007 EF-1 ERV LP- 36,37
LP- 31 PTO
PTL LP- 18 HAND DRYER - BRAND: XLERATOR, STAINLESS STEEL 120V
GFCI

D
MODEL NO. XL-SB-110-120
WP/GFCI

GFCI D F PTC
PTR

LP- 11
LP- 25
. LP- 54
GFCI

LP- 11 E025 E004

Revision Schedule
LP- 26 LP- 16
LP- 35 HV POWER POINT JUNCTION BOX FOR HOOD VENTILATOR
M

LP- 16
LP- 7 E008 GENERAL NOTES - NEW WORK :
E003 LP- 28

Description
HV 3PH JUNCTION BOX, SURFACE MOUNTED FOR FUTURE
LP- 40,41
AHU-1 LP- 38,39 1- ELECTRICAL DRAWINGS SHALL BE READ IN CONJUNCTION WITH ARCHITECTURAL AND MECHANICAL DRAWINGS. J
ELEVATOR. PROVIDE ROUGH-IN FROM THE
S

E011
EF-2
LP- 18
LP- 17 LP- 54
ELECTRICAL PANEL TO THE JUNCTION BOX.
LP- 12 E012 2- OBTAIN AND PAY FOR PERMITS REQUIRED BY THE ELECTRICAL SAFETY AUTHORITY AND LOCAL INSPECTION AUTHORITIES FOR
LP- 61,62,63 LP- 16 Tr WH-2 WH-1 THIS WORK. PRESENT FINAL CERTIFICATES TO CONSULTANT AND/OR OWNER.
LP- 12
LP M SINGLE DATA OUTLET COMBINED WITH HDMI OUTLET
AS NOTED.

LP- 42,43
LP- 44,45

LP- 49,50
LP- 51,52
E024
3- CARRY OUT ALL WORK IN ACCORDANCE WITH OESC (ONTARIO ELECTRICAL SAFETY CODE) REGULATIONS INCLUDING BULLETINS,
E013
LP- 53
AND ELECTRICAL SAFETY AUTHORITY INSPECTION REQUIREMENTS.
LP- 53 WP/GFCI DATA AND IP TELEPHONE OUTLET C/W TWO RJ45
LP- 26
4- ALL EQUIPMENT SHALL BE NEW AND CSA (OR EQUIVALENT PER OESC) APPROVED UNLESS OTHERWISE NOTED. KEYSTONES & FACEPLATE

5- VISIT THE SITE OF THE PROJECT AND BECOME FAMILIAR WITH THE SITE CONDITIONS AND UNDERSTAND THE EXTENT OF THE WORK. IP TELEPHONE OUTLET
LP- 53
LP- 23

No.
6- ON COMPLETION OF PROJECT AND BEFORE FINAL PAYMENT SUBMIT ONE (1) SET OF AS-BUILT DRAWINGS WITH ALL
CHANGES AND BURIED SERVICES EXACT LOCATIONS NOTED THEREON. PROVIDE AS-BUILT DRAWINGS IN AUTOCAD FORMAT.
2 LP- 29 SINGLE DATA OUTLET
LP- 22 E009
7- GUARANTEE ALL MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE YEAR FROM DATE OF ACCEPTANCE BY OWNER/CONSULTANT.
PTO
PTO

PROVIDE WRITTEN GUARANTEE.

MH: 20FT LED TV PROVIDED BY THE OWNER
LED SCREEN

8- PROVIDE ALL CUTTING, PATCHING, AND PAINTING FOR ELECTRICAL WORK, UNLESS NOTED OTHERWISE.
OPEN AREA

POWER & SYSTEMS FLOOR

9- PROVIDE FIREPROOFING WHERE CABLES PASS THROUGH FLOORS OR FIRE RATED WALLS. PLUG AND PROVIDE APPROVED WALL MOUNTED BUSINESS POE WIRELESS ACCESS POINT
FIRE STOP AND SEAL WITH BAULKING COMPOUND ANY HOLES AND OPENINGS LEFT DUE TO DEMOLITION WORK. WAP
BRAND: CISCO OR LINKSYS
LP- 24

E019

LP- 23 10- WIRING SHALL BE CONCEALED IN WALLS OR ABOVE CEILINGS UNLESS OTHERWISE APPROVED.
LP- 22 E009 24 GIGABIT POE PORTS, STACKABLE ETHERNET SWITCH
3 11- DEFINITIONS: FOLLOWING ARE DEFINITIONS OF WORDS FOUND IN THIS SPECIFICATION AND ON ASSOCIATED
LP- 29 MH: 20FT
E006 DRAWINGS.
A. "CONCEALED" - HIDDEN FROM NORMAL SIGHT IN FURRED - SPACES, SHAFTS, CEILING SPACES, WALLS, UNDERFLOOR, TELEPHONE TERMINAL BOX
AND PARTITIONS.
TB
LP- 23 B. "EXPOSED" - ALL ELECTRICAL WORK VISIBLE TO BUILDING OCCUPANTS.
C. "PROVIDE" - (AND ALL TENSES OF "PROVIDE"] SUPPLY INSTALL, WIRE AND CONNECT COMPLETE. DIGITAL WALL THERMOSTAT - PROVIDED & INSTALLED BY
LP- 53
D. "INSTALL" - (AND ALL TENSES OF "INSTALL")-INSTALL. WIRE AND CONNECT COMPLETE, PRODUCTS AND SERVICES SPECIFIED. T MECHANICAL CONTRACTOR.
E. ”SUPPLY”-SUPPLY ONLY. ROUGH-IN AND WIRED BY ELECTRICAL CONTRACTOR.
F. "OR APPROVED EQUAL" - MATERIAL OR EQUIPMENT PROPOSED BY CONTRACTOR, IN LIEU OF THAT SPECIFIED, AS APPROVED
LP- 23 E022
LP- 23 E003 BY CONSULTANT.
G. "AS INDICATED" - AS SHOWN ON DRAWINGS AND/OR NOTED IN SPECIFICATIONS. INDOOR COMMERCIAL CEILING FAN. PROVIDED & INSTALLED
T
WAP BY ELECTRICAL CONTRACTOR.
12- ALL WIRING SHALL BE COLOUR CODED AS PER OESC AND BE IDENTIFIED WITH BRADY OR EQUIVALENT SELF-STICKING PERMACODE BRAND: GLOBAL INDUSTRIAL
E006
WIRE MARKERS. ALL JUNCTION BOXES IN CONCEALED CEILING SPACES SHALL BE LABELED WITH PEN MARKER AS TO CIRCUITS MODEL # 292700 - SIZE: 72", C/W REMOTE CONTROL
WP/GFCI LED SCREEN

PLAN
CONTAINED THEREIN.
LP- 26

13- FASTENINGS AND SUPPORTS:

a. SUPPORT EQUIPMENT, CONDUIT OR CABLES USING CLIPS, SPRING LOADED BOLTS, CLAMPS DESIGNED AS ACCESSORIES GROUNDING ROD SYSTEM
N N TO BASIC CHANNEL MEMBERS.
b. INSTALL FASTENINGS AND SUPPORT AS REQUIRED FOR EACH TYPE OF EQUIPMENT, CONDUIT AND CABLES AND IN
FIRST FLOOR - POWER & SYSTEMS - NEW WORK MEZZANINE - POWER & SYSTEMS - NEW ACCORDANCE WITH MANUFACTURERS RECOMMENDATION.
TC TELEPHONE CABINET, WALL MOUNTED
SCALE: 1 : 75 SCALE: 1 : 75
14- GROUNDING: GROUND ALL EQUIPMENT IN ACCORDANCE WITH CODE REQUIREMENTS. REFER TO GROUNDING ROD DETAILS

John R. Park Homestead Heritage Centre

ON SHEET E303

915 County Road 50, Essex, Ontario N0R 1G0

15- ON THE COMLETION OF THE WORK UPDATE THE PANEL SCHEDULE AS REQUIRED WITH THE LOAD NAME AND CIRCUIT NUMBER.
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

STORAGE ROOM
TO EXTERIOR LIGHTS

200 A LP-A
7 - JAW METER
125 A
600V
3P, 4W
M 350 A,
120/208V
3P, 4W
ELECTRONIC
ASTRONOMIC
7-DAY TIME SWITCH
INTERMATIC MN:ET8000

ERCA
DRY TRANSFORMER SPD 120 KA
112.5KVA, 600/208V, 3PH, 60 HZ

FROM HYDRO-1

Cable Size: 4 # 3/0 AWG COPPER RW90 -XLPE Drawn By Checked By

IN 53MM (2") PVC CONDUIT SCHEDULE 80.
ai ai
6/1/2020 9:15:03 AM

FROM HYDRO-1 POLE TO THE STORAGE ROOM

Project No
2020
POWER DISTRIBUTION SYSTEM THIS LINE IS 4" LONG
Sheet No

MIN. 3 M
1 Lighting - Vestibule 15 A 1 29 VA 1080... -- -- -- 37
2 LED Tape Millwork - Reception & Corridor (102 &... 15 A 1 100 VA 1250... 2 30 A AHU1, AHU2, & AHU3 - Mezzanine 38
3 Lighting - Office 15 A 1 112 VA 1250... -- -- -- 39
AT LEAST GROUND ROD
4 Lighting - Survery 15 A 1 112 VA 3000... 2 40 A Stove - Survery (108) 40
3M 3/4" x 10'
5 Receptacles - Common Hallway 20 A 1 180 VA 3000... -- -- -- 41 3/4" x 10' COPPER CLAD COPPER CLAD This drawing is not to be used for
construction unless it is countersigned
6 Emergency Exit Lights 15 A 1 209 VA 3500... 2 40 A Tankless WH2 - CKT-1 42 GROUND ROD by the Project Architect
7 Hood Ventilator - Survery (108) 20 A 1 250 VA 3500... -- -- -- 43
8 Lighting - Mezzanine 15 A 1 286 VA 3500... 2 40 A Tankless WH2 - CKT-2 44 Issued For (YYMMDD)
9 Exterior Lights Astronomic Switch 15 A 1 308 VA 3500... -- -- -- 45 TENDER 2020.06.01
10 Lighting & Exhaust Fan - Female Washroom 15 A 1 343 VA 1725... 1 20 A Hand Dryer - Male WR (112) 46
11 GFCI Receptacles - Survery (108) 20 A 1 360 VA 4000... 2 50 A Electrical Duct Heater - Mezzanine 47
12 Receptacles - Survery (108) & Closet 20 A 1 360 VA 4000... -- -- -- 48
13 Electric Radiant Heater - Vestibule 15 A 1 375 VA 7000... 2 80 A Tankless WH1 - CKT-1 49
14 Lighting & Exhaust Fan- M. Washroom & Hallway 15 A 1 200 VA 7000... -- -- -- 50
15 Lighting - Reception & Corridor 15 A 1 479 VA 7000... 2 80 A Tankless WH1 - CKT-2 51
16 Receptacle - Storage (106) & Water Station (GFCI) 20 A 1 540 VA 7000... -- -- -- 52
17 Receptacles - Mezzanine Storage (116) & Attic... 20 A 1 540 VA 720 VA 1 20 A Receptacles - Creative Commons (107) 53
18 Lighting & Exhaust Fans - Storage & Universal WR 15 A 1 570 VA 720 VA 1 20 A Receptacles - Mezzanine Open (114) 54
19 Emergency Lights 15 A 1 576 VA 55
20 Lighting - Creative Commons (107) 15 A 1 615 VA 1725... 1 20 A Hand Dryer - Male WR (112) 56
21 Electric Radiant Heaters - Common Hallway (110) 15 A 1 750 VA 1725... 1 20 A Hand Dryer - Universal WR (105) 57 BOLLARD LIGHT MOUNTING DETAIL GROUNDING ELECTRODES
22 Ceiling Fans - Reception & Creative Common 20 A 1 800 VA 1200... 3 20 A Future Elevator 58
23 Receptacles - Creative Commons (107) 20 A 1 900 VA 1200... -- -- -- 59
24 Door Operators - Vestibule(101) & Universal WR... 15 A 1 1000... 1200... -- -- -- 60
25 Fridge - Survery (108) 20 A 1 1000... 7300... 3 90 A Outdoor Heat Pump 61 BRAND: KUEFLER (KLP) OR APPROVED EQUIVALENT
26 GFCI Receptacles - Exterior Walls 20 A 1 1080... 7300... -- -- -- 62 PART NO. P650X8-8" DIAX18" LENGHT
27 Receptacles - Office (104) 20 A 1 1260... 7300... -- -- -- 63 WEB ADDRESS: www.kuefler-lightning.com

Date
28 Receptacles - Reception & Corridor (102 & 103) 20 A 1 1260... 64
29 Floor Receptacles - Creative Commons (107) 20 A 1 1440... 0 VA 1 20 A Spare 65 112.5KVA, 3PH, 600V/208V DRY DISTRIBUTION TRANSFORMER
30 Fire Place - Reception (102) 20 A 1 1500... 0 VA 1 20 A Spare 66
31 GFCI Receptacle Dishwasher - Survery (108) 20 A 1 1500... 0 VA 1 20 A Spare 67 BRAND: HAMMOND POWER SOLUTIONS (HPS)
32 Hand Dryer - Female WR (111) 20 A 1 1725... 0 VA 1 20 A Spare 68 PART NO. SG3A0112PB0C
33 Hand Dryer - Female WR (111) 20 A 1 1725... 0 VA 1 15 A Spare 69
34 Floor Receptacles - Reception (102) 20 A 1 720 VA 0 VA 1 15 A Spare 70
35 Microwave - Survery (108) 20 A 1 1800... 0 VA -- -- Space 71

Revision Schedule
36 ERV - Mezzanine 15 A 2 1080... 0 VA -- -- Space 72 FRONT VIEW SIDE VIEW
Total Load: 39107 VA 38575 VA 39191 VA
Total Amps: 327 A 321 A 327 A PATCH PANEL IDENTIFICATION

Description
RACK IDENTIFICATION
Legend: 718.82 MM 685.8 MM CIRCUIT NUMBER (TYPICAL)
- Copper Busbars. 28.3 IN 27 IN
PORT NUMBER

304.8 MM
TYPICAL PANEL NOTES 12 IN 1-A-10
IP TELEPHONE
1. ALL CONDUCTORS SHALL BE COPPER. LP-1F1-1
2. THE CONTRACTOR SHALL VERIFY ADEQUATE SPACE ONSITE FOR ALL EQUIPMENT PRIOR ORDERING. 558.8 MM
3. CONTRACTOR TO VERIFY ALL REQUIREMENTS AS PER MANUFACTURERS SPECIFICATION PRIOR TO ORDERING. 22 IN
4. 120KA, SURGE PROTECTION DEVICE (SPD) SHALL BE PROVIDED. 2.00" x 3.00"

No.
5. PANELS SHALL BE COMPLETE WITH LOCKABLE DOORS AND LOCKABLE BREAKERS. 914.4 MM TYPICAL PER SIDE
6. PANELS SHALL BE COMPLETE WITH MAIN BREAKER. 36 IN (CABLE ENTRY / EXIT) DATA
7. REFER TO PANEL SCHEDULES FOR QUANTITY AND SIZE OF BREAKERS.
GROUND LUG
8. ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR THE MOUNTING AND SUPPORTING OF THE PANEL.

ELECTRICAL PANEL SCHEDULE

1-A-11

718.82 MM 609.6 MM
21.50 IN 24 IN
DATA OUTLET RECEPTACLE IDENTIFICATION

ENCLOSURE COLOR : ANSI 61 GREY

& DETAILS
POWER DISTRIBUTION TRANSFORMER

EMERGENCY ALARM EMERGENCY ALARM

John R. Park Homestead Heritage Centre

PROVIDE LAMACOID
DOOR OPERATOR IDENTIFICATION NAMEPLATE

915 County Road 50, Essex, Ontario N0R 1G0

SIREN & STROBE SIREN & STROBE MC

LEGEND LP
BIM 360://2020 JRPH Heritage Centre/2020 MEP-360.rvt

IN THE EVENT OF AN EMERGENCY

PUSH EMERGENCY BUTTON LED ILLUMINATED CONTROL KIT - FLUSH MOUNTED
DOOR STRIKE TO BE RELEASED
AND AUDIBLE AND VISUAL SIGNAL BRAND: CAMDEN - CX-WC SERIES
WILL ACTIVATE
IN CASE OF EMERGENCY
DC DOOR CONTROLLER LOCKABLE
DOOR LOCKED WHEN RED DOOR LOCKED WHEN RED TO BE LOCATED PTO PUSH TO OPEN BUTTON
UNLOCKED WHEN GREEN UNLOCKED WHEN GREEN NEAR TOILET SEAT
LED INDICATOR DS DOOR STRIKE
DS
PTL PUSH TO LOCK BUTTON

LOCK PUSH PUSH LOCK PUSH DOOR PUSH TO CALL BUTTON LI LOCK INDICATOR
STRIKE PUSH BUTTON
HAND DRYER
PTC PUSH TO CALL BUTTON FOR ASSISTANCE
INDICATOR TO TO INDICATOR TO FOR ASSISTANCE
TO RESET
1067 MM

OPEN OPEN LOCK INDICATOR (PTC)

1067 MM

(PTR)
(PTO) (PTL) PTR PUSH TO RESET BUTTON MC MAGNETIC CONTACT
EMERGENCY SIREN & STROBE
ESS ANNOUNCIATOR FOR ASSISTANCE

ERCA
PANEL BOARD IDENTIFICATION

OUTSIDE WASHROOM INSIDE WASHROOM Drawn By Checked By

ai ai
6/1/2020 9:15:04 AM

Project No
2020
THIS LINE IS 4" LONG
Sheet No
BARRIER FREE RESTROOM CONTROL KITS
THE INFORMATION INCLUDED IN THIS ELECTRONIC DRAWING FILE IS PROTECTED BY COPYRIGHT. UNAUTHORIZED USE OF THIS FILE WITHOUT THE WRITTEN PERMISSION OF ARCHITECTTURA INC. ARCHITECTS IS PROHIBITED.
ARCHITECTTURA INC. ARCHITECTS IS RESPONSIBLE ONLY FOR INFORMATION SHOWN ON A MECHANICAL REPRODUCTION OF THIS DRAWING FILE THAT HAS BEEN SIGNED AND SEALED BY A REGISTERED ARCHITECT EMPLOYED BY THE FIRM.
THIS DRAWING SHEET IS 36"X24" IN SIZE. IT IS RECOMMENDED THAT ANY REPRODUCTION, ELECTRONIC OR OTHERWISE, BE TO THE SAME SHEET SIZE
TO ENSURE THE ACCURACY OF DRAWING SCALES DEPICTED ON THIS SHEET. THIS DRAWING IS NOT TO BE SCALED - USE FIGURED DIMENSIONS ONLY.
E302

(Approved) 2 Storey Residential
90% (60)
(Approved) 2 Storey Residential
10 pages
2 Storey Residential House
94% (33)
2 Storey Residential House
8 pages
Proposed One-Storey Residential House (Complete Set of Plans) - To Be Printed
100% (10)
Proposed One-Storey Residential House (Complete Set of Plans) - To Be Printed
5 pages
2 Storey House Plan
75% (4)
2 Storey House Plan
7 pages
Philippine Electrical Code
96% (26)
Philippine Electrical Code
37 pages
Complete Construction Drawing
67% (9)
Complete Construction Drawing
22 pages
Compilation of ARCHITECTURAL STRUCTURAL PLUMBING ELECTRICAL PLAN Edolmo Liwanag Jr. Sangalang VIno CE 302
92% (13)
Compilation of ARCHITECTURAL STRUCTURAL PLUMBING ELECTRICAL PLAN Edolmo Liwanag Jr. Sangalang VIno CE 302
12 pages
Electrical Load Schedule
88% (8)
Electrical Load Schedule
11 pages
Electrical Plans
90% (10)
Electrical Plans
2 pages
Substation Design Manual PDF
100% (25)
Substation Design Manual PDF
445 pages
Proposed 2 Storey Residential BLDG - BT3 1 PDF
75% (4)
Proposed 2 Storey Residential BLDG - BT3 1 PDF
13 pages
Table of Ampacities For Wire Sizes, Conversion of AWG To Metric Sizes and Number of Conductors in A Conduit
73% (11)
Table of Ampacities For Wire Sizes, Conversion of AWG To Metric Sizes and Number of Conductors in A Conduit
17 pages
Two Storey Commercial Building Electrical Layout Plan PDF
94% (18)
Two Storey Commercial Building Electrical Layout Plan PDF
15 pages
Soriano Residence: A 3-Storey RESIDENTIAL BUILDING W/ Basement
100% (1)
Soriano Residence: A 3-Storey RESIDENTIAL BUILDING W/ Basement
32 pages
Electrical Project Design
86% (14)
Electrical Project Design
225 pages
Electrical Layout and Estimate 2nd Edition by Max B. Fajardo JR., Leo R. Fajardo
92% (140)
Electrical Layout and Estimate 2nd Edition by Max B. Fajardo JR., Leo R. Fajardo
349 pages
Electrical All Sizing Calculation
96% (26)
Electrical All Sizing Calculation
123 pages
IPASOLINK 400 - Operation PDF
No ratings yet
IPASOLINK 400 - Operation PDF
544 pages
Load Schedule
83% (6)
Load Schedule
1 page
12 Electrical Design Basis PDF
79% (39)
12 Electrical Design Basis PDF
32 pages
Elevator Calculations
100% (13)
Elevator Calculations
10 pages
Electrical Design Criteria
100% (6)
Electrical Design Criteria
533 pages
Electrical Design Analysis
88% (8)
Electrical Design Analysis
12 pages
Riser Diagram 1 Single Line Diagram 2: General Notes and Specification
100% (2)
Riser Diagram 1 Single Line Diagram 2: General Notes and Specification
11 pages
710 Edge 2
No ratings yet
710 Edge 2
52 pages
24 Harman St. - DOB SUBMISSION PLANS PDF
No ratings yet
24 Harman St. - DOB SUBMISSION PLANS PDF
18 pages
C Users PC Desktop 2 Storey Residential House Architectural Template
No ratings yet
C Users PC Desktop 2 Storey Residential House Architectural Template
1 page
AMLI Wynwood
No ratings yet
AMLI Wynwood
79 pages
Plans
No ratings yet
Plans
59 pages
Electrical Design Calculations Book
67% (6)
Electrical Design Calculations Book
121 pages
Kasturi Furnace & CCM Shed Drawing
No ratings yet
Kasturi Furnace & CCM Shed Drawing
1 page
467 Monroe Street - Dob Approval Plans - 2014.07.10 PDF
No ratings yet
467 Monroe Street - Dob Approval Plans - 2014.07.10 PDF
24 pages
Riverside Bid Set
No ratings yet
Riverside Bid Set
106 pages
2 Storey Apartment BLDG
No ratings yet
2 Storey Apartment BLDG
16 pages
313 WEST 117th STREET New York, Ny
100% (1)
313 WEST 117th STREET New York, Ny
17 pages
AHA Condominium Project in Phnom Penh - Tenant Work0331
No ratings yet
AHA Condominium Project in Phnom Penh - Tenant Work0331
82 pages
Friar Project Combine Architectural Plans
No ratings yet
Friar Project Combine Architectural Plans
16 pages
Alfond Inn - Set For Portfolio - Part 6
No ratings yet
Alfond Inn - Set For Portfolio - Part 6
27 pages
Architectural Layout1
No ratings yet
Architectural Layout1
1 page
Richview Square: Re-Issued For Zoning MARCH 22, 2019
No ratings yet
Richview Square: Re-Issued For Zoning MARCH 22, 2019
35 pages
19LG0121 PLAN - Part1
No ratings yet
19LG0121 PLAN - Part1
31 pages
A.Ebal Cand - Zamb.pg1of14
No ratings yet
A.Ebal Cand - Zamb.pg1of14
1 page
Reflected Ceiling Plan G
No ratings yet
Reflected Ceiling Plan G
1 page
Crizaldo - Construction Drawings
No ratings yet
Crizaldo - Construction Drawings
28 pages
Alfond Inn - Set For Portfolio - Part 1
0% (1)
Alfond Inn - Set For Portfolio - Part 1
20 pages
BD2 Floor Plan PDF
100% (1)
BD2 Floor Plan PDF
1 page
Perspective: Site Development Plan Vicinity Map
No ratings yet
Perspective: Site Development Plan Vicinity Map
5 pages
Caroline Hofer Suarez: Vicinity Map Facade Perimeter Fence
No ratings yet
Caroline Hofer Suarez: Vicinity Map Facade Perimeter Fence
1 page
Section 206 Hofmann Dam Phase Ii: Solicitation Set
No ratings yet
Section 206 Hofmann Dam Phase Ii: Solicitation Set
24 pages
AR1
No ratings yet
AR1
1 page
Republic of The Philippines Province of La Union Municipality of Naguilian
No ratings yet
Republic of The Philippines Province of La Union Municipality of Naguilian
1 page
A-308 - BKH - Roof - Floor - Ceiling Plan - Rev02
No ratings yet
A-308 - BKH - Roof - Floor - Ceiling Plan - Rev02
1 page
Revised 1
100% (1)
Revised 1
1 page
For Permit - AR - STJ-BATANGAS
No ratings yet
For Permit - AR - STJ-BATANGAS
6 pages
230 E 63Rd Associates, LLC 230 East 63Rd Street NEW YORK, NY 10021
No ratings yet
230 E 63Rd Associates, LLC 230 East 63Rd Street NEW YORK, NY 10021
10 pages
M-1006 - Sixth Floor Mvac Layout
No ratings yet
M-1006 - Sixth Floor Mvac Layout
1 page
Dela Cruz For Blueprint Checking 12-05-2022
No ratings yet
Dela Cruz For Blueprint Checking 12-05-2022
14 pages
Yc Pergola Amepfs (Asbuilt)
No ratings yet
Yc Pergola Amepfs (Asbuilt)
21 pages
Floor Plan W/ Furniture Layout Floor Pattern Layout: D C B A
No ratings yet
Floor Plan W/ Furniture Layout Floor Pattern Layout: D C B A
7 pages
A1-Camella Alora Blk.13 Lot 8
No ratings yet
A1-Camella Alora Blk.13 Lot 8
1 page
A House Design Drawings in Victoria, Australia
No ratings yet
A House Design Drawings in Victoria, Australia
22 pages
Maqueta Mariel PDF
No ratings yet
Maqueta Mariel PDF
17 pages
Tatytute Luyahan for Building Permit 1
No ratings yet
Tatytute Luyahan for Building Permit 1
8 pages
BT 3 Finals
No ratings yet
BT 3 Finals
15 pages
2-18-2020 - GAC MSC - Acworth - Add2 Full Set
No ratings yet
2-18-2020 - GAC MSC - Acworth - Add2 Full Set
21 pages
Alfond Inn - Set For Portfolio - Part 3
No ratings yet
Alfond Inn - Set For Portfolio - Part 3
18 pages
06 13025 - S - Torrance Transit Center - Backcheck 1 - Structural - 2017-04-10 PDF
No ratings yet
06 13025 - S - Torrance Transit Center - Backcheck 1 - Structural - 2017-04-10 PDF
49 pages
Permit Submittal Set: Tenant Improvement
No ratings yet
Permit Submittal Set: Tenant Improvement
9 pages
2021.01.15 - Bid Set - CMH - Ortho Renovation and Addition - 0200707.00
No ratings yet
2021.01.15 - Bid Set - CMH - Ortho Renovation and Addition - 0200707.00
67 pages
Detail of Floor Drain Detail of Floor Cleanout Vent Thru Roof Detail
No ratings yet
Detail of Floor Drain Detail of Floor Cleanout Vent Thru Roof Detail
1 page
Item 2.2 - 2005 Rock Street
No ratings yet
Item 2.2 - 2005 Rock Street
39 pages
2sty 10cl
No ratings yet
2sty 10cl
67 pages
09-28-2018 Architectural Plans and Exhibits
No ratings yet
09-28-2018 Architectural Plans and Exhibits
55 pages
Kitchen Detail
No ratings yet
Kitchen Detail
1 page
3 Storey Building Final Plan
100% (1)
3 Storey Building Final Plan
15 pages
11th Floor Plan 09102019 FCD PDF
No ratings yet
11th Floor Plan 09102019 FCD PDF
10 pages
A06-02 Bay Sections
No ratings yet
A06-02 Bay Sections
1 page
Architectural Structural Plumbing Electrical
No ratings yet
Architectural Structural Plumbing Electrical
24 pages
Proposed 2Bhk Flats: First Floor Plan
No ratings yet
Proposed 2Bhk Flats: First Floor Plan
1 page
Building Laws-Compiled - READ
No ratings yet
Building Laws-Compiled - READ
46 pages
Parlade Family Memoir
From Everand
Parlade Family Memoir
Bob Parlade
No ratings yet
I'M STILL HEALING: A poetry collection of love and trauma.
From Everand
I'M STILL HEALING: A poetry collection of love and trauma.
Koko Escoto
No ratings yet
Biblical Lessons from Grandpa: Preparing the Next Generations
From Everand
Biblical Lessons from Grandpa: Preparing the Next Generations
Michael F. Schmidt
No ratings yet
Growing Up on the Farm
From Everand
Growing Up on the Farm
Pamela Ingram May
No ratings yet
Violet Rose #0
From Everand
Violet Rose #0
Emma Davis
No ratings yet
Special and Different: The Autistic Traveler: Judgment, Redemption, & Victory
From Everand
Special and Different: The Autistic Traveler: Judgment, Redemption, & Victory
Steven Tomasino
No ratings yet
Basic Electrical Design Calculations
100% (11)
Basic Electrical Design Calculations
591 pages
Stadium Plans A1 Size
No ratings yet
Stadium Plans A1 Size
21 pages
Rogelio Singca - Building Permit Plans v3
No ratings yet
Rogelio Singca - Building Permit Plans v3
9 pages
Electrical Design Calculations
92% (12)
Electrical Design Calculations
34 pages
Typical HT & LT Power Cable Sizing Calculation
100% (6)
Typical HT & LT Power Cable Sizing Calculation
13 pages
Electrical Design & Detailed Engineering 1
100% (6)
Electrical Design & Detailed Engineering 1
391 pages
Log
No ratings yet
Log
25 pages
Nonsite Org Why Architecture Matters As Art As Never Before
No ratings yet
Nonsite Org Why Architecture Matters As Art As Never Before
15 pages
The Forgotten Forge
No ratings yet
The Forgotten Forge
9 pages
Ethiopia Double Leach Pit With Concrete Slab
No ratings yet
Ethiopia Double Leach Pit With Concrete Slab
18 pages
CE6603-Design of Steel Structures
No ratings yet
CE6603-Design of Steel Structures
12 pages
Adams Rite Electromagnetic Locks: Also See Securitron On Page 212
No ratings yet
Adams Rite Electromagnetic Locks: Also See Securitron On Page 212
9 pages
Intro To VLSI System Design
100% (1)
Intro To VLSI System Design
46 pages
Practice Profiles
No ratings yet
Practice Profiles
59 pages
Five Lessons Life Has Taught Me
No ratings yet
Five Lessons Life Has Taught Me
263 pages
Cover Pages of The Monograph, "Didactic Design of Imageable Architecture" WWW - amazon/Didactic-Design-Imageable-Architecture-Maringa/dp/1479309702ISBN-139781479309702 ISBN-10:1479309702
No ratings yet
Cover Pages of The Monograph, "Didactic Design of Imageable Architecture" WWW - amazon/Didactic-Design-Imageable-Architecture-Maringa/dp/1479309702ISBN-139781479309702 ISBN-10:1479309702
2 pages
8.T-ProofCrete 709 13-03-28
No ratings yet
8.T-ProofCrete 709 13-03-28
2 pages
Documentation Fabric Compensators
No ratings yet
Documentation Fabric Compensators
8 pages
Stm32 Embedded Software Offering
No ratings yet
Stm32 Embedded Software Offering
12 pages
Extended Abstract - Empirical Formula Generation For Preliminary Ship Design
No ratings yet
Extended Abstract - Empirical Formula Generation For Preliminary Ship Design
3 pages
Operating System Question Bank Final
No ratings yet
Operating System Question Bank Final
22 pages
STS Bahasa Inggris K-4 SEM 1
No ratings yet
STS Bahasa Inggris K-4 SEM 1
3 pages
AC701 Ethernet Design Creation: June 2014
No ratings yet
AC701 Ethernet Design Creation: June 2014
49 pages
Buses
No ratings yet
Buses
19 pages
Architects in Banaglore, Delhi A'bad, Pune
100% (1)
Architects in Banaglore, Delhi A'bad, Pune
14 pages
H Furniture 2014 Catalogue Corner en PDF
No ratings yet
H Furniture 2014 Catalogue Corner en PDF
23 pages
NUMed Accommodation - Eco Nest Apartment, Iskandar Puteri
No ratings yet
NUMed Accommodation - Eco Nest Apartment, Iskandar Puteri
4 pages
Tib Gi Developer Guide
No ratings yet
Tib Gi Developer Guide
318 pages
EM - 1110!2!2102 Waterstops and Other Preformed Joint Materials For Civil Works Structures
No ratings yet
EM - 1110!2!2102 Waterstops and Other Preformed Joint Materials For Civil Works Structures
23 pages
Villa - BOQ - Medows With Price
No ratings yet
Villa - BOQ - Medows With Price
4 pages
14.summary Sheet A2
No ratings yet
14.summary Sheet A2
1 page
Secenic Design: Scenic Design in General
No ratings yet
Secenic Design: Scenic Design in General
4 pages
Chapter 10: Planning and Cabling Networks
No ratings yet
Chapter 10: Planning and Cabling Networks
5 pages
2008 04 04 SNMP On ERS 8600 TCG NN48500564
No ratings yet
2008 04 04 SNMP On ERS 8600 TCG NN48500564
44 pages