Packet Tracer - Use LLDP to Map a Network

Addressing Table
Local Interface and
Device Interface IP Address Subnet Mask
Connected Neighbor
Blank

Edge G0/0 192.168.1.1 255.255.255.0

Blank

Edge
S0/0/0 Blank S0/0/0 - ISP
Blank blank

SVI 192.168.1.2 Blank

Blank

G0/0 209.165.200.10 Blank G0/0 - ISP

Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank
Blank Blank Blank Blank

Blank

Objectives
Map a network using LLDP and SSH remote access.

Background / Scenario
A senior network administrator requires you to map the Remote Branch Office network and discover
information about all of the devices in the network. You must record all of the network device names, IP
addresses and subnet masks, and physical interfaces interconnecting the network devices.
To map the network, you will use SSH for remote access and the Link Layer Discovery Protocol (LLDP) to
discover information about neighboring network devices. Because LLDP is a Layer 2 protocol, it can be used
to discover information about devices that do not have Layer 3 connectivity. You will record the information
that you gather to complete the Addressing Table and provide a topology diagram of the Remote Branch
Office network.

© 2016 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 5 www.netacad.com
Packet Tracer - Use LLDP to Map a Network

You will need the IP address for the remote branch office, which is 209.165.200.10. The local and remote
administrative usernames and passwords are:
Local Network
Username: admin01
Password: S3cre7P@55
Remote Branch Office Network
Username: RBOadmin
Password: S3cre7P@55

Instructions

Part 1: Use SSH to Remotely Access Network Devices

In Part 1, you will use the Admin-PC to remotely access the Edge gateway router. Next, from the Edge router
you will SSH into the Remote RBO Office.
a. On the Admin-PC, open a command prompt.
b. SSH into the gateway router at 192.168.1.1 using the username admin01 and the password
S3cre7P@55.
PC> ssh –l admin01 192.168.1.1
Open
Password:

Edge#
Note: Notice that you are placed directly into privileged EXEC mode. This is because the admin01 user
account is set to privilege level 15.
c. The Edge router was previously configured to use CDP. Switch S1 has already been configured to use
LLDP. Issue the show cdp command to verify CDP is currently active. Disable CDP by issuing the
following command:
Edge(config)# no cdp run
d. LLDP can be configured to both transmit and receive on a specific interface. Configure Edge so that it
receives LLDP messages from S1 but does not send messages to S1 for security purposes Enable
LLDP.
Edge(config)# lldp run
Edge(config)# int g0/0
Edge(config-if)# no lldp transmit
Edge(config-if)# exit
e. Use the show lldp neighbors command to verify that Edge is receiving messages from S1.
f. Connect to S1 with SSH from Edge router using the admin01 credentials. Issue the show lldp
neighbors command. Notice that S1 did not receive information from Edge.
Edge# ssh –l admin01 192.168.1.2
Password:

S1> show lldp neighbors

S1> exit

© 2016 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 5 www.netacad.com
Packet Tracer - Use LLDP to Map a Network

g. Exit from the connection with S1 to return to the Edge router CLI. Use the show ip interface brief and
show interfaces commands to document the Edge router’s physical interfaces, IP addresses, and
subnet masks in the Addressing Table.
Edge# show ip interface brief
Edge# show interfaces
h. From your session with Edge router, connect with SSH to the Remote RBO Office at 209.165.200.10 with
the username RBOadmin and the same password used for admin01.
Edge# ssh –l RBOadmin 209.165.200.10
Password:

RBO-Edge#
Question:

After connecting to the Remote RBO Office at 209.165.200.10 what piece of previously missing
information can now be added to the Addressing Table above?
Type your answers here.

Part 2: Use LLDP to Discover Neighboring Devices

You are now remotely connected to the RBO-Edge router. Using LLDP, begin looking for connected network
devices.
a. Issue the show ip interface brief and show interfaces commands to document the RBO-Edge router’s
network interfaces, IP addresses, and subnet masks. Add the missing information to the Addressing
Table.
b. Security best practice recommends only running LLDP when needed, so LLDP may need to be turned on.
Use a show lldp command to test its status.
RBO-Edge# show lldp
% LLDP is not enabled
c. You need to turn on LLDP, but it is a good idea to only send LLDP information to internal network devices
and not to external networks. Discover which interface is connected to the internet by issuing the
command show ip interface brief. Enable the LLDP protocol and completely disable LLDP on the
interface that is connected to the internet.
RBO-Edge# configure terminal
RBO-Edge(config)# lldp run
RBO-Edge(config)# interface g0/0
RBO-Edge(config-if)# no lldp transmit
RBO-Edge(config-if)# no lldp receive
RBO-Edge(config-if)# exit
d. Issue a show lldp neighbors command to find any neighboring network devices.
Note: LLDP will only show connected devices that are also running LLDP.
RBO-Edge# show lldp neighbors
Question:

Is there a neighboring network device? What type of device is it? What is its name? On what interface is it
connected? Is the device’s IP address listed? Record the information in the Addressing Table.
Type your answers here.

© 2016 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 5 www.netacad.com
Packet Tracer - Use LLDP to Map a Network

e. Use the show ip route command to determine the address of the device that you found with the show
lldp neighbors command. Based on the information provided about the local address in the routing table
and the prefix length of the network use that information to determine the neighbor address.
f. To find additional information from the neighboring device, use the show lldp neighbors detail
command:
RBO-Edge# show lldp neighbors detail
Question:

What other piece of potentially sensitive information is listed?

Type your answers here.

Note: The current version of Packet Tracer does not provide the Management Address of the neighbor
device. In this activity several neighbor device addresses have been provided in the Addressing Table.
g. Connect to the neighbor device with SSH to discover other devices that may be its neighbors.
Note: To connect with SSH use the same Remote RBO Office username and password.
RBO-Edge# ssh –l RBOadmin <the ip address of the neighbor device>
Question:

After successfully connecting with SSH, what does the command prompt show?
Type your answers here.

h. You are remotely connected to the next neighbor. Use the show lldp neighbors command, and the
show lldp neighbors detail command, to discover other connected neighbor devices.
Question:

What types of network devices neighbor this device? Record any newly discovered devices in the
Addressing Table. Include their hostname, interfaces, and IP addresses.
Type your answers here.

Add the newly discovered device name next to the SVI entry for address 192.168.4.131.
i. Connect to the SVI for address 192.168.4.131 using SSH and credentials used previously. If prompted for
an enable secret password, use the same password as used for RBOAdmin. Use the show lldp
neighbors command, and the show lldp neighbors detail command, to discover other connected
neighbor devices.
Question:

What types of network devices neighbor this device? Record any newly discovered devices in the
Addressing Table. Include their hostname, interfaces, and IP addresses.
Type your answers here.

Place the newly discovered device name next to the SVI entry for address 192.168.4.132.
j. Connect to the SVI for address 192.168.4.133 using SSH and credentials used previously. Issue the
command show lldp, you should receive a message:
% LLDP is not enabled

Enable lldp globally as in Step C. There is no need to configure transmit or receive options because
they are on by default. Use the show lldp neighbors command, and the show lldp neighbors detail
command, to discover other connected neighbor devices.
Question:

What types of network devices neighbor this device? Record any newly discovered devices in the
Addressing Table. Include their hostname, interfaces, and IP addresses. It may be beneficial to reconnect

© 2016 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 5 www.netacad.com
Packet Tracer - Use LLDP to Map a Network

to the previously discovered devices to display neighbors one more time to complete the entire
addressing table now that all devices are configured for LLDP.
Type your answers here.

k. Draw a topology of the Remote RBO Office network using the information that you have gathered with
LLDP.
End of document

© 2016 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 5 www.netacad.com