Scribd
Upload
184 views

Structural Calculation Template

This structural analysis and design report is for a proposed building located in an unspecified location. It details project details, reference codes and standards, material specifications, design load criteria, load combinations, building geometry, load calculations, structural analysis, and design of beams, girders, columns, and footings. The building structural system utilizes special reinforced concrete moment frames. Design is based on national structural and building codes for the Philippines. Concrete, reinforcing steel, structural steel, welds and anchor bolts meet specified material strengths. Dead, live, and seismic loads are considered in load combinations for design, drift, and deflection checks.

Uploaded by

Melecio Magbuhos II
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
184 views

Structural Calculation Template

This structural analysis and design report is for a proposed building located in an unspecified location. It details project details, reference codes and standards, material specifications, design load criteria, load combinations, building geometry, load calculations, structural analysis, and design of beams, girders, columns, and footings. The building structural system utilizes special reinforced concrete moment frames. Design is based on national structural and building codes for the Philippines. Concrete, reinforcing steel, structural steel, welds and anchor bolts meet specified material strengths. Dead, live, and seismic loads are considered in load combinations for design, drift, and deflection checks.

Uploaded by

Melecio Magbuhos II
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 19

STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)

& DESIGN REPORT IN (INSERT LOCATION)

STRUCTURAL ANALYSIS
AND DESIGN REPORT
PROPOSED (INSERT TYPE OF BUILDING)
IN (INSERT LOCATION
Location: (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
I. PROJECT DETAILS

Project Name :
Location :
Occupancy Category : Essential Facilities
Building Structural System : Moment Resisting Frame Systems – Special Reinforced Concrete MF’s

II. REFERENCE CODE AND STANDARDS


- National Structural Code of the Philippines
- National Building Code of the Philippines

III. MATERIAL SPECIFICATIONS

Concrete – reinforced concrete design shall be in accordance with NSCP 2015. The specified minimum
compressive strength of the concrete by cylinder test at 28days age shall be as follows:
Foundation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Beams - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Columns - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Suspended Slab - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Slab on Grade - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Lean Concrete - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10.0MPa (1450PSI)

Reinforcing Steel – minimum yield strength of reinforcing bar shall be as follows:

16mmØ and smaller reinforcing bar - - - - - - - - - - - - - - 276MPa (Grade 40)


20mmØ and bigger reinforcing bar - - - - - - - - - - - - - - - 414MPa (Grade 60)

Structural Steel – All structural steel such as wide flange, angles, channels, pipes and plates shall conform to
ASTM A36 or equivalent with minimum yield strength of 248MPa.

Weld – Welding electrode shall be E70XX, minimum welding 6mm. Fu = 480MPa

Anchor Bolt – Anchor Bolt shall conform to ASTM 325 or equivalent. Anchor bolt shall be designed for maximum
tensile stress of 140MPa on the tensile stress area of the bolt.
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
IV. DESIGN LOAD CRITERIA

Dead Loads (DL) – consist of the weight of all materials of construction incorporated into the building or other
structure, including but not limited to walls, floors, roofs, ceilings, stairways, finishes, cladding and other similarly
incorporated architectural and structural items, and fixed service equipment, including the weight of cranes.

Live Loads (LL) – shall be the maximum loads expected by the intended use or occupancy but in no case shall be
less than the loads required by this section.
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
Roof Live Loads (LL) – shall be designed for the unit live loads, Lr, set forth in Table 205-3. The live loads shall be
assumed to act vertically upon the projected area on a horizontal plane.

Earthquake Loads (EQX & EQZ), section 208


STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)
V. LOAD COMBINATIONS
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

LOAD COMBINATION FOR DESIGN


LOAD COMB 16 1.2DL + 0.5LL + 1.0EQX
LOAD COMB 17 1.2DL + 0.5LL - 1.0EQX
LOAD COMB 18 1.2DL + 0.5LL + 1.0EQZ
LOAD COMB 19 1.2DL + 0.5LL - 1.0EQZ
LOAD COMB 20 0.9DL + 1.0EQX
LOAD COMB 21 0.9DL - 1.0EQX
LOAD COMB 22 0.9DL + 1.0EQZ
LOAD COMB 23 0.9DL - 1.0EQZ

LOAD COMBINATION FOR DRIFT CHECK


LOAD COMB 16 1.2DL + 0.5LL + 1.0EQX
LOAD COMB 17 1.2DL + 0.5LL - 1.0EQX
LOAD COMB 18 1.2DL + 0.5LL + 1.0EQZ
LOAD COMB 19 1.2DL + 0.5LL - 1.0EQZ
LOAD COMB 20 0.9DL + 1.0EQX
LOAD COMB 21 0.9DL - 1.0EQX
LOAD COMB 22 0.9DL + 1.0EQZ
LOAD COMB 23 0.9DL - 1.0EQZ

LOAD COMBINATION FOR DEFLECTION CHECK


LOAD COMB 24 1.0DL + 1.0LL + 1.0RL

VI. GEOMETRY
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

3D STRUCTURAL RENDERED VIEW

VII. LOAD CALCULATION


STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

VIII. ANALYSIS
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

IX. DESIGN

DESIGN OF BEAMS AND GIRDERS


STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

DESIGN OF COLUMNS
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

DESIGN OF FOOTINGS
STRUCTURAL ANALYSIS PROPOSED (INSERT TYPE OF BUILDING)
& DESIGN REPORT IN (INSERT LOCATION)

You might also like