6 5 4 3 2 1

PARTS LIST
ITEM QTY NAME OF ITEM DESCRIPTION
1 4 NUT FOR SHAFT SLIDER HEX NUT M16
2 1 SUPPORT
D D
11 7 SLIDER-RIGHT
3 4 BASE HOLDER SLIDER
A 4 2 HOLDER SHAFT OD 70
6 MM
5
5 2 CLAMP SHAFT OD 70
MM
4
6 1 SHAFT PUMP 11 IMP OD MAX 70 MM
7 1 SLIDER HOLLOW L100 X W100
3 8 3 NUT FOR TYING Hex Nut M10
IMPELLER
2 9 1 HOLDER B IMPELLER
C 10 1 IMP OD 242 MM X 105 C
16 MM X 101 MM
11 1 SUPPORT SLIDER-LEFT
1 12 1 HOLDER A IMPELLER
13 3 BOLT FOR TYING HEX HEAD BOLT M10 X
IMPELLER L120
A ( 0,15 : 1 ) 17 14 6 HANDLE
15 9 BOLT FOR ADJUSTER Hex-Head Bolt
HOLDER M10XL120
10
16 2 SHAFT SLIDER
17 1 FRAME HOLLOW 100X100X5
12
B B
9

13
STAMP AT LOCATION SHOWN ON TECH. SPEC. PROCEDURE (TSP) DIM. TOL UNLESS OTHERWISE SPECIFIED TITTLE :
DRAWING
IF IN DOUBT PLEASE ASK
1. JOB LOT TRACEBILITY : .................
RADIUS = .30"/.60" [0.76/1.52]
14 2. MATERIAL : BRASS
3. DIMENSION VERIFY : .............
FRACTION
X.X
= 1/16" [1,6]
= .2" CONCENTRICITY = .10" FIM [.25]
COMPONENTS OF JIG ASSY IMPELLER DRAWN BY DATE
X.XX = .05" PARALLELISM = .01"/1" [0.25/25.4]
15 4. NDT : ..............
5. HARDNESS : ................
X.XXX = .002" SQUARENESS = .01"/1"[0.25/25.4]
PUMP RASDATE
A 6. COATING : ................
7. PAINTING : ................
ANGLE
CORNERS
= .1/2"
= .010" / 0.030" [0,25/0,76"]
SURFACE = 250 [6.3] N9
DIMENSION IN [ ] ARE MM
REVIEWED BY
HS DATE A
8. COLOR : ................. DIMENSION ARE IN : M.C : T.C : PSI : PR : REF : APPVD BY
9. STAMP (--) MONOGRAM MARKING INDICATED THUS
REVISION INDICATED THUS INCHES
PRODUCT [Y] [N] THIRD ANGLE PROJECTION IIII MM RELEASED DATE SCALE :
(IF YES STAMP API LOGO & LICENCE)
DUAL (INCHES & MM)
PT. FUJII IRONWORKS TEKNOLOGI
SPECIAL PROCESS
BEYOND OF EXPECTATION DWG NO :

c 2018. PT FUJII IRONWORKS TEKNOLOGI : THE INFORMATION CONTAINED ON THIS DRAWING IS COPYRIGHT & THE SOLE SIZE : WEIGHT : SHEET :
PROPERTY OF FUJITEK-CIKARANG. THIS INFORMATION SHALL NOT BE RELEASED, DISCLOSED OR DUPLICATED FOR
REPRODUCTION IN PART OR WHOLE WITHOUT WRITTEN PERMISSION.

6 5 4 3 2 1
 6 5 4 3 2 1

D D

1220,00
C C
2890,00

3000,00
500,00
225,00

B B

STAMP AT LOCATION SHOWN ON TECH. SPEC. PROCEDURE (TSP) DIM. TOL UNLESS OTHERWISE SPECIFIED TITTLE :
DRAWING
IF IN DOUBT PLEASE ASK
1. JOB LOT TRACEBILITY : .................
FRACTION = 1/16" [1,6] RADIUS = .30"/.60" [0.76/1.52]
2. MATERIAL : BRASS
CONCENTRICITY = .10" FIM [.25]
3. DIMENSION VERIFY : .............
X.X
X.XX
= .2"
= .05" PARALLELISM = .01"/1" [0.25/25.4] DIMENSION OF JIG ASSY IMPELLER DRAWN BY DATE
4. NDT : ..............
5. HARDNESS : ................
X.XXX = .002" SQUARENESS = .01"/1"[0.25/25.4]
PUMP RASDATE
A 6. COATING : ................
7. PAINTING : ................
ANGLE
CORNERS
= .1/2"
= .010" / 0.030" [0,25/0,76"]
SURFACE = 250 [6.3] N9
DIMENSION IN [ ] ARE MM
REVIEWED BY
HS DATE A
8. COLOR : ................. DIMENSION ARE IN : M.C : T.C : PSI : PR : REF : APPVD BY
9. STAMP (--) MONOGRAM MARKING INDICATED THUS
REVISION INDICATED THUS INCHES
PRODUCT [Y] [N] THIRD ANGLE PROJECTION IIII MM RELEASED DATE SCALE :
(IF YES STAMP API LOGO & LICENCE)
DUAL (INCHES & MM)
PT. FUJII IRONWORKS TEKNOLOGI
SPECIAL PROCESS
BEYOND OF EXPECTATION DWG NO :

c 2018. PT FUJII IRONWORKS TEKNOLOGI : THE INFORMATION CONTAINED ON THIS DRAWING IS COPYRIGHT & THE SOLE SIZE : WEIGHT : SHEET :
PROPERTY OF FUJITEK-CIKARANG. THIS INFORMATION SHALL NOT BE RELEASED, DISCLOSED OR DUPLICATED FOR
REPRODUCTION IN PART OR WHOLE WITHOUT WRITTEN PERMISSION.

6 5 4 3 2 1