Certificado de STD FAME's 37comp Sigma Aldrich RFQ50-217
Certificado de STD FAME's 37comp Sigma Aldrich RFQ50-217
Page 2 of 5
Certiied
Certiicate of Analysis Reference
SUPELCO 37 COMPONENT FAME MIX
Material
Product ID CRM47885
Lot LRAB8645
Expiration Date April 2021
Manufacturing Date May 2018
Storage Conditions Freeze
Solvent/Matrix METHYLENE CHLORIDE
12
6 8 18
4
3 16
21
27 34
2
1 5 7 9 10 11 13 15 19 20 22 24 26 2830 33 35
17 2325 2931 36 37
32
14
Order or Elution
1. Methyl Butyrate
2. Methyl Hexnoate
3. Methyl Octanoate
4. Methyl Decanoate (Caprate)
5. Methyl Undecanoate
6. Methyl Laurate
7. Methyl Tridecanoate
8. Methyl Myristate
9. Myristoleic Acid Methyl Ester
10. Methyl Pentadecanoate
11. Cis-10-Pentadecenoic Acid methyl Ester
12. Methyl palmitate
13. Methyl Palmitoleate (Methyl Cis 9-Hexadecenoate)
14. Mehtyl Heptadecanoate
15. Cis-10-Heptadecenoic Acid Methyl Ester (Methyl cis-10heptad)
16. Methyl Stearate
17. Trans-9-Elaidic Acid Methyl Ester (Methyl elaidate)
18. Cis-9-Oleic Acid Methyl Ester
19. Methyl Linoleate
20. Linolelaidic Acid Methyl Ester (Methyl Linolelaidate)
21. Methyl Arachidate
22. Gamma-LinolenicAcid Methyl Ester (Methyl gamma-linolenate)
23. Methyl Cis-11 Eicosenoate
24. Methyl Linolenate
25. Methyl Heneicosanoate
26. Cis-11,14-Eicosadienoic Acid Methyl Ester
27. Methyl Behenate
28. Cis-8,11,14-Eicosatrienoic Acid Methyl Ester
29. Methyl Erucate (Cis-13-Docosenoate) (Methyl cis-13-docosenoa)
30. Cis-11,14,17-Eicosatrienoic Acid Methyl Ester
31. Methyl Tricosanoate
32. Methyl Cis-5,8,11,14-Eicosatetraenoic (Methyl Arachidonate)
33. Cis-13,16-Docosadienoic Acid Methyl Ester
34. Methyl Lignocerate (Methyl Tetracosanoate)
35. Methyl Cis-5,8,11,14,17-Eicosapentaenoate
36. Methyl Nervonate (Methyl cis-15-tetracosenoate)
37. Cis-4,7,10,13,16,19-Docosahexaenoate
Additional Information:
Analytical Method Parameters:
Page 4 of 5
Certiied
Certiicate of Analysis Reference
SUPELCO 37 COMPONENT FAME MIX
Material
Product ID CRM47885
Lot LRAB8645
Expiration Date April 2021
Manufacturing Date May 2018
Storage Conditions Freeze
Solvent/Matrix METHYLENE CHLORIDE
1 Certified value - based on the gravimetric preparation (corrected by the raw material purity) and analytically verified by RTC with associated uncertainties from the preparation and analytical procedures.
2 The standard deviation is the robust statistical standard deviation from the round robin interlaboratory study.
3 Acceptance limits are based on Interlaboratory Study Results. These ranges are recommendations only.
4 Ucrm - Uncertainty values in this document are expressed as Expanded Uncertainty (Ucrm) corresponding to the 95% confidence interval. Ucrm is derived from the combined standard uncertainty multiplied by
the coverage factor k, which is obtained from a t-distribution and degrees of freedom. The components of combined standard uncertainty include the uncertainties due to characterization, homogeneity, long term
stability, and short term stability (transport). The components due to stability are generally considered to be negligible unless otherwise indicated by stability studies. The mathematical representation of the Ucrm
calculation is as follows:
2 2 2
u CRM = u char + u hom ogeneity + u stability
5 k: Coverage factor derived from a t-distribution table, based on the degrees of freedom of the data set. Confidence interval = 95%
Traceability: The standard was manufactured under an ISO/IEC 17025:2005 certified quality system. The balance used to weigh raw materials is accurate to +/- 0.0001g and calibrated
regularly using mass standards traceable to NIST. All dilutions were preformed gravimetrically. Additionally, individual analytes are traceable to NIST SRMs where available and
specified above.
Homogeneity: Homogeneity was assessed in accordance with ISO Guide 35. Completed units were sampled using a random stratified sampling protocol. The results of chemical
analysis were then compared using a one-way analysis of variance approach as described by TNI EL-V3-2009 Appendix A.2. See Instructions for minimum sub-sample size.
THIS PRODUCT WAS DESIGNED, PRODUCED AND VERIFIED FOR ACCURACY AND STABILITY IN ACCORDANCE WITH ISO/IEC 17025:2005 (ANAB Cert AT-1467) and ISO
GUIDE 34:2009 (ANAB Cert AR-1470).
MSDS reports for components comprising greater than 1.0% of the solution or 0.1% for components known to be carcinogens are available upon request.