Scribd
Upload
104 views2 pages

One Little Remote 4 Quick Start Guide

The One Little Remote 4 is a remote control for Micro cameras that allows control of focus, iris, record status, and more features. It includes a remote, cables, and mounting bolt. Basic usage instructions explain how to control focus stops and auto focus from the main screen. The document also provides directions for configuring settings like lens selection, SBUS channels, and display for different camera models. It concludes by thanking the user and previewing upcoming features.

Uploaded by

Julien Camera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
104 views2 pages

One Little Remote 4 Quick Start Guide

The One Little Remote 4 is a remote control for Micro cameras that allows control of focus, iris, record status, and more features. It includes a remote, cables, and mounting bolt. Basic usage instructions explain how to control focus stops and auto focus from the main screen. The document also provides directions for configuring settings like lens selection, SBUS channels, and display for different camera models. It concludes by thanking the user and previewing upcoming features.

Uploaded by

Julien Camera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

One Little Remote 4

Quick start guide


The full user manual and video tutorials can be found at http://onelittlegoat.com/support.

If you have any questions or need support, email [email protected].


Config menu options
What’s included
• 1 x remote
Camera cinema or studio
• 1 x 30cm cable Dial rec turn record activation
• 1 x 10cm 3.5mm to dual rca cable via dial on or off.
• 1 x 30mm mounting bolt
• 2 x tiny jack screws for attaching cable to camera Dial focus turn focus control via
dial on or off.
Basic usage – main screen
Check rec yes or no to polling
camera continually for record
status (best to leave yes unless
you notice focus control is jerky)

Flip oled flip the screen 180


degrees for mounting remote
upside down.

Lanc on yes or no to internally


generated lanc commands

Show help hide or show the


context sensitive help in the
remote.

Focus stops OLR name used for Bluetooth


Enter focus stop mode by double tapping the dial. identification

By default, focus stops are set to the extremities of focus.

Press a slider 1 (left) to go to focus stop A, and slider 2 (right) to go to focus stop B. Turn dial or press same slider a
second time to stop movement.

You can adjust speed and ramp with the sliders while moving towards a focus stop.

Select a lens
1) From main screen hold
dial to open Setup
Menu,
2) Left slider to select
LENS, press left slider
3) Use left slider to select
lens by name,
4) Press left slider to set
active lens

More lens will be added to


firmware over time. If your
lens is not listed, use default
(no fstop value displayed).
Bounce mode
While in focus stop mode, double press the dial to start bounce mode. When you activate a focus stop (press slider)
the remote will move between focus stops continuously until you double press dial again or turn the dial.

Hold dial to return to previous screen.

Auto-focus and auto-iris


Auto focus activates the centre point focus feature of your micro camera. Auto-iris sets auto exposure. Please note
that auto iris is not linked to setting the iris; using the slider to adjust iris after using auto-iris will reset the iris to the
last used iris setting before auto-iris was activated. Auto iris is only good for getting a ‘optimal’ iris setting from the
camera.

Set sbus channels


To set sbus channels:

1) From the main screen, hold dial to open Setup Menu,


2) Use left slider to select SBUS and press left slider to open SBUS Menu,
3) Use left slider to select camera function, use right slider to select sbus channel for selected function,
4) Press right slider to save,
5) Hold dial to return to previous menu.

Ensure the sbus channels in the remote menu on your camera match those on the remote.

Micro Studio Camera (4k)


To display settings correctly on a Micro Studio, do the following;

1) From the main screen, hold dial to open Setup Menu,


2) Use left slider to select CONFIG and press left slider to open CONFIG Menu,
3) Use left slider to select ‘Camera=’ option,
4) Use right slider to select ‘Camera=studio’, press right slider to save,
5) Hold dial to return to previous menu.

Sleep mode (restart remote)


If the camera and remote lose sync, or you want to switch the remote off (if it is being powered by DC input), hold
the dial until the sleep message appears.

To turn a remote on that is asleep, hold dial until wake up message appears.

Back of the remote

Thanks!
I really appreciate you trying my remote
and I hope it helps you have more fun
using your Micro Camera. Any
suggestions, please email
[email protected].

PTZ and zoom/focus servo for manual


lens coming soon! Plus an updated app.

You might also like