Machine Translated by Google

Version : AVRIL 2017

FTP_FR_MT26_18_30_3X150_MM2_Al_PE_NOR_NR

Cables Moyennes Tension NFC 33-226

MV cables NFC 33-226
MT
26 6/10 kV to 18/30 insulated
NF C 33-226
The cable MT 26 is a cable intended for the distribution of public medium tension from 6/10 kV to 18/30 kV. It
responds to the norm NF C 33-226.
This type of product is made up of three phase conductors, assembled in a torsade for the underground version, assembled
around a steel porter for the aerial version.

The MT 26 cable is a cable for the public power distribution 6/10 kV to 18/30 kV. It
meets the NF C 33-226 standard.
This type of product has three phase conductors, assembled twisted to the underground version assembled around a
steel support for aerial release.

Constitution / Design
1-Ame:

Aluminum or copper, round,

To install Classe 2 retreinte.

2 - Screen semi-conductor extruded :

Polyéthylène reticulé.
3 - Isolant extruded :

Polyéthylène reticulé.
4 - Screen semi-conductor extruded tubular peelable :
Elastomer.

Poudre gonflante sur semi

conductor to assure the
waterproofness.

5 - Screen metallic :
ruban aluminum

longitudinal collé à la gaine

exterior.

6- Gain de protection:
PE

General characteristics / General characteristics

Norm / Standard : NFC 33-226

Rayon of curvature / Bending factor when laying : 6,5

times the outer diameter of the cable for 3X and 13 times the outer diameter of the cable for 1X / 6,5
times external diameter of the cable for 3X and 13 times external diameter of the cable for 1X.

Modes of laying currents / Installation :

,
A l'air libre : fixation on support / Open air : mounting supports
* Enterré : avec protection mécanique / Buried : with mechanical protection

SERVICE METHODS SIM*** Page : 1/5 Bd Ahl Loghlam Ain Sebaa Route de Tit Mellil BP 2551 CASABLANCA
Machine Translated by Google

Version : AVRIL 2017

FTP_FR_MT26_18_30_3X150_MM2_Al_PE_NOR_NR

FICHE TECHNIQUE PRODUCT

1 - IDENTIFICATION OF THE PRODUCT :

Cable Type: tripolar

Code article: 57275150500

Designation Product : NFC33-226 18/30KV 3x150 AL 18/30

Current tension : kV

Tension minimum (U0) : kV 18

Tension nominal (Unom) : kV 30

Tension maximum (Umax) : kV 36

Norms of Fabrication: NFC 33-226

Number of conductors (phase) : 3

Section nominal of the soul (Phase) : mm² 150

Material conductor (phase) : ALUMINUM

Screen semi-conductor extruded (Internal) : XLPE

Type Isolant Conductor (phase) : Polyethylene reticule (PR)

Screen semi-conductor extruded (External) : XLPE

Section (Porter) : mm² SANS PORTEUR

Porter's material : SANS PORTEUR

Type Screen on Semi-conductor extruded (External) : Poudre gonflante + 1 Ruban Alu/PE

Type Gain External : P.E Normal

Color gain external : Noir

Gain with or without Anti termite : sans

Gain with or without anti rongeur : sans

PROPERTIES:
Cable NFC 33-226 18/30 3X150 mm² ALUMINUM Gaine en : PE
Product:
normal noir

2 - CHARACTERISTICS OF THE L'AME :

Information : PHASE Unity

Metal of the soul …………………………………………………………………. , ALUMINUM

Class of metal……………………………………………………………… : class 2

Type of soul ………………………………………………………………….. : Cables retreint

Form of the soul ………………………………………………………………………… : circular

Composition of the soul ……………………………………………………….. : 19 X 3.15

Section calculated of the soul …………………………………………… : 148.07 mm²

Diamètre mini de l'soul ……………………………………………………. , 14 mmm

Diameter maxi of the soul ………………………………………………………. , 14.1 mmm

DC Resistance linear max sur soul à 20 °C ………………………………. : 0.206 ohm/km

Temperature arm…………………………………………………….. : DC 90 °C
Resistance line max on arm aluminum at 90 °C (current continuous) : AC Resistance 0.264 ohm/km
line max on arm aluminum à 90 °C (Courant Alternative) : Pertes de charge maximum 0.265 ohm/km
(Monophasé) …………………………………. : Maximum charge rates 1.6006 kw/km
(Triphasé) ………………………………….. : 4.8018 kw/km

3 - CHARACTERISTICS ISOLANTS (3 Couches) :

SERVICE METHODS SIM*** Page : 2/5 Bd Ahl Loghlam Ain Sebaa Route de Tit Mellil BP 2551 CASABLANCA
Machine Translated by Google

Version : AVRIL 2017

FTP_FR_MT26_18_30_3X150_MM2_Al_PE_NOR_NR

FICHE TECHNIQUE PRODUCT

1 - IDENTIFICATION OF THE PRODUCT :

Information : A°/ value Unity

Semi conductor interne :

Epaisseur Mini Ecran Semi Conducteur INTERNE ( en tout point ) …………… : 0.45 mmm

Epaisseur Mini Ecran Semi Conducteur INTERNE ( en 1 point ) …………… : 0.35 mmm

Epaisseur Nominale Ecran Semi Conducteur extrudé … ………………………... : 0.5 mmm

Epasseur Maxi Screen Semi Conductor INTERNE , , 0.55 mmm

Diameter approximative sur Semi Conductor INTERNE ………………………………….. : 15.2 mmm

Electrical Resistivity of the screen at (90° +/- 2°) C ……………………… <= 1000 Ohm.m

…………………. : B°/ Isolant : Epaisseur Mini Isolant ( en tout 6.45 mmm

point )……………………………………………………………….. : Epaisseur Mini 5.75 mmm

6.5 mmm
Isolant ( en 1 point ) ………… …………………………………………………….. : Epaisseur Nominale Isolant ………………………………………………………
Epaisseur Maxi Isolant ………………………………………………………………………………… : 6.55 mmm

Approximate Diameter on Isolant……………………………………………………………….. : 28.3 mmm

Resistance to traction ……………………………………………………………………………………….. : >= 12.5 MPa

Lengthening at the rupture ……………………………………………………………………………. : >= 200 ,
C°/ Semi conductor extèrne :
Epaisseur Mini Ecran Semi Conducteur EXTERNE ( en tout point) 0.45 mmm

…………… : Epaisseur Mini Ecran Semi Conducteur EXTERNE ( en 1 point) 0.35 mmm

………………………... : Epaisseur Nominale Ecran , 0.5 mmm

Semi Conducteur EXTERNE Epaisseur Maxi ,, 0.55 mmm

Ecran Semi Conducteur EXTERNE Diamètre ………………………………….. : 29.4 mmm

approximatif sur Semi Conducteur EXTERNE Height Mini des Cannelures sur 0.45 mmm

,,
Semi Conducteur EXTERNE ( en tout point) … : Height Nominale des Cannelures 0.5
sur Ecran Semi Conducteur EXTERNE mmm

Hauteur Maxi des Cannelures sur Ecran Semi Conducteur EXTERNE …………………. , 0.55 mmm

Approximate Diameter on Cannelures …………………………………………………………………... : 30.5 mmm

Resistance to traction ……………………………………………………………………………………….. : >= 7 MPa

Lengthening at the rupture ……………………………………………………………………………. : >= 150 ,
Electrical resistivity of the screen at (90° +/- 2°) C …………………………………………. : <= 500 Ohm.m
Gradient to the level of the screen on the soul ……………………………………………………… : 3.81 kv/mm
Gradient to the level of the screen on env. isolation………………………………………….. : 2.05 kv/mm

4 - CHARACTERISTICS SCREEN METALLIC :

Information : value Unity

Number of rubs ……………………………………………………………………………………… : 1

Epaiseur Ruban ……………………………………………………………………………………… : 0.2 mmm

Face in Aluminum on the inside and on the other face

Matériaux ruban…………………………………………………………………………………….. :
outdoor polyethylene
Methode d'utilisation ………..……………………..……………………………………………………………… : en long
Approximate diameter of ribbon ………………………………………………………………… : 31 mmm

Electrical resistance of the metallic screen …………………………………………… ……. , <= 2 ohm/km

5 - CHARACTERISTICS OF THE GAIN OF PROTECTION :

SERVICE METHODS SIM*** Page : 3/5 Bd Ahl Loghlam Ain Sebaa Route de Tit Mellil BP 2551 CASABLANCA
Machine Translated by Google

Version : AVRIL 2017

FTP_FR_MT26_18_30_3X150_MM2_Al_PE_NOR_NR

FICHE TECHNIQUE PRODUCT

Information : 1 - IDENTIFICATION OF PRODUCT : Epaisseur Mini de gain ( en 1 point) value Unity
………………………..………………………………………… : Epaisseur Nominale de gain 1.77 mmm

…… …………………………………………………………………………….. : 2.2 mmm

Epressor Maxi de gaine …………………………………………………………………………….. : 2.25 mmm

Approximate diameter on gain ………………………………………………………………… : 35.42 mmm

Resistance to traction …………………………………………… …………………………………………… : >= 12.5 MPa

Lengthening to rupture …………………………………………………………………………… : >= 300 ,

Nexans - NFC 33-226 - 150 mm² Al - 18/30 (36) kV - W Numéro_de_semaine et

Marquage sur Gaine:
Année_de_Fabrication - POPY - EI=6.5 mm - EC=0.2 mm - EG=2.2 mm

Nature of marqueage: Mollettes Relief à chaud

6 - ASSEMBLAGE DU CABLE :

Information : value Unity

Diameter of cable …………………………………………………………………..………………………………………… : 76.51 mmm

Rayon of curvature ……………..…………………………………………………………………………………….. : 497 mmm

Marking on Cable Assemblé …………… …………… : MARQAGE METRICN° PHASE , , N° DE TOURET DE RECEPTION

7 - CHARACTERISTICS COLLISION STANDARD :

Information : value Unity

Poids Net Approximate: 3 681.0 kg/km

Type of Tourette Bois: PT

Fabrication standard length: 250 mt/tourette

Diamètre Joue sans douves : 2300 mmm

Largeur hors tout: 1160 mmm

Diamètre Joue sur douves extèrnes : 2340 mmm

Poids Brut approximative (Produit + Touret) Sans douves : 1 216.3 Kg/Km

Poids Brut approximate (Produit + Touret) Avec douves : 1 303.0 Kg/Km

8 - ELECTRICAL CHARACTERISTICS :

Information : value Unity

[Dm] = Distance between the threads including the thickness of the insulator : 30.1 mmm

Frequency………………………………………………………………………………………………. , 50 Hz

Length of the cable 1 kilometers

………………………………………………………………………………………………… : Cos(Phi) (if 0.8

the illumination value is 1 / if the starting force of the motor is the value [r] = 7.05 mmm

4.269503546
Rayon ray ……………………………………………………………… …………… : Dm/r ……………………………………………………………………………………… :

[L] = Coefficient of Self-Induction …………………………………………………….. : 0.34 mH/km

Inductance (Réactance) ………………………………………………………………… : 0.1068 ohm/km

Impedance at 50Hz et 90°C ……………………………………………………….. : 0.285 ohm/km

Capacitance ………………………………….…………………… 0.18 µF/km
………………………………….. : Line resistance of the conductor …………………………………………….. : 0.2400 A/km

SERVICE METHODS SIM*** Page : 4/5 Bd Ahl Loghlam Ain Sebaa Route de Tit Mellil BP 2551 CASABLANCA
Machine Translated by Google

Version : AVRIL 2017

FTP_FR_MT26_18_30_3X150_MM2_Al_PE_NOR_NR

FICHE TECHNIQUE PRODUCT

Intensity Admissible 1
(A)- IDENTIFICATION OF THE PRODUCT : Drop the tension ()
cable entry Cable on tablets Cos fi = 0.3 Cos fi = 0.8 0.33 0.49
304 369
, The admissible intensities are given for a pose in a tree at a depth of 0,8 m.
106 107 108 109

9 - CHARACTERISTICS OF THE PORTEUR :

Information : PHASE Unity

Number of princes and porters ………………………………………………………………. ,

Diameter of brin…………………………………………………………………………………… : mmm

Diamètre a porter ………………………………………………………………………….. : Matière mmm

isolation du porter ……………………………… ………………………………….. :

Epressor Mini in one point ………………………………………………………………….. : mmm

Epaiseur moyenne Mini …………………………………………………………………………… : mmm

Epressor Nominale ……………………………………………………………………………. : Epaisseur mmm

Maxi ……………………………………………………………………………………..……. : Diameter mmm

approximatif sur isolant porteur ……………………………………………. : Couleur isolant mmm

……………………………………………………… ………………………………….. : °C

The minimum rupture charge………………………………………………………………. , kN

SERVICE METHODS SIM*** Page : 5/5 Bd Ahl Loghlam Ain Sebaa Route de Tit Mellil BP 2551 CASABLANCA