Scribd
Upload
363 views

AUT Theory Paper-1

aut theory paper 1

Uploaded by

steve a
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
363 views

AUT Theory Paper-1

aut theory paper 1

Uploaded by

steve a
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 25
2¥/ei{%. PetStass) ‘TWI TRAINING & CERTIFICATION AUT UT (Phased Array) Coursework 2 Enter all answers on answer sheet 28 y © yegegeys: 040 mm 1) _Inthe auto-setup in the figure above which channel or channels use a 1% skip pulse-echo technique? 2 In the auto-setup in the figure above which sound paths are displayed? b) downstream only ) both up and downstream d) itis not possible to tell from the figure 3) In the auto-setup what does the “skew" define? a) Refracted angle b) the a pase with carbide adjustment 4) none of the above ‘TWIUT CW L Issue 0 1 ‘When starting up the PWZ system what hardware is to be detected in the 4 "POD" configuration? a) MCDU Et bi Focus ©) the water pump 5) Inthe following Wizard image how many elements are activated in the transmitter focal law? yt o, possible to tell 68) In the acquisition dialogue box (below), what is the purpose of Averaging? 4) to increase gain without using the amplifier circuits 2 Which colour is the measurement cursor? Red ©) Green 4) Black TWIUT CW 1 Issue 0 2 In the image below, which of the horizontal lines-on the A-scan represents the Time Gate? 8) he short line at 5%FSH ©) the long line at 33% FSH 4) none of the lines indicate the time gate © The image shown in question 8, 2 vertical lines are seen. They are a) the amplitude and time gates b) the limits can for the waveform collection the reference and marker cursors for the voltage 10) The acquisition unit won't start when the unit power is on and the power switch is on. What is the probable cause of the problem? a) AC power source is defective b) jains protection fuse may be blown @) The “Kill Switch” on the scanner is activated With frequency remaining constant the length of the near field will decrease if : tow Frol Neo diet | probe ctisaate ©) Beam spread increases 4) Quartz is utilised as the transducer efdw 12) The Weld definition input variables are saved /imported as what type of file ?~ ©) std a) .nfg \ TWIUT CW 1 Issue 0 13) 14) 15) 16) 17) 18) ‘When using information derived from the cursors what is the “delta’ value ? a)_ The value of the focal law ©) The zoom ve jiven area d)_ The length of a defect under a red or blue cursor In the Weld Definition window what do the “fll sections 1, 2, 3” refer to ? a) The number of weld passes in the fil section b) The number of fill zones in the fill section. j The number of fll targets in the fill section What is the advantage of “unlinking” the Tx-Rx while maximising on a reflector b) It permits the focal law to move freely in any direction ©)_ It speeds the calibration process 3 g 2 98 oy 33 g poe o@> on ‘The refraction angle of longitudinal ultrasonic waves passing {om water nto a metalic material at angles ether than normal to the interface is primarily a function of the impedance ratio (t= Z7..) of water to metal the frequency ofthe ultrasonic beam. the density ratio of water to metal, When testing, ithe ultrasonic instrument is set wath an ‘excessively high pulse repeiion rate, which ofthe following may ‘The screen trace will become too light to ee. The time-base tine vill Become distorted, The intial pulse wil disappear ‘The cute point ofa crystal is “de Tha taparatune ot vb aril vi lwe te pieo-lacio “SRE ult on he cstalvner the amptuteo bration is zero “The temperature at vhich materials reverse thelr polar magnetic properties None ofthe above ‘What i the hal-angle beam spread of a 1.25 om diameter 2.25 MHz transducer in water (V = 1.5 x 10° cm/sec)? 25° “os Heat conduction, viscous tition, elastic hysteresis, and ‘scattering ae four diferent mechanisms which lead to Fefraction beam spreading ‘saturation. What would be the wavelength of the energy in lead (V: 10" emisec) itis tested with a 25 MHz transducer? 119.0m, 0.525 em, oot9em, 35 A 0. 36 c. D Which of the following is not considered relevant to an ECA cniteria flaw tength flaw height vertical and lateral interaction between flaw components, “The length ofthe near feld for a 2.5 cm diameter, 5 MHz. transducer placed ino i approximately: (V= 1.4 x10" mises) 22.3¢m. Material noise consis of ow amplitude, random signals trom ‘numerous emall reflectors tregulry dieibuted throughout the test place. This noise may be reduced bythe use of” Paral beam probos High trequency probes. “Twin crystal probes

You might also like