PN2293

Pressure sensor with display

PN-025-REN14-MFRKG/US/ /V

1 alphanumeric display 4-digit red/green

2 LEDs Display unit / switching status
3 programming button
4 upper part of the housing can be rotated 345°

Product characteristics
Number of inputs and outputs Number of digital outputs: 2; Number of analogue outputs: 1
Measuring range -1...25 bar -14.5...362.5 psi -0.1...2.5 MPa
Process connection threaded connection 1/4" NPT internal thread
Application
Special feature Gold-plated contacts
Measuring element ceramic-capacitive pressure measuring cell
Application for industrial applications
Media liquids and gases
Medium temperature [°C] -25...80
Min. bursting pressure 350 bar 5075 psi 35 MPa
Pressure rating 150 bar 2175 psi 15 Mpa
Vacuum resistance [mbar] -1000
Type of pressure relative pressure; vacuum
MAWP (for applications 70 bar 1015 psi 7 MPa
according to CRN)

ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — PN2293-01 — 21.02.2020 —
PN2293
Pressure sensor with display
PN-025-REN14-MFRKG/US/ /V

Electrical data
Operating voltage [V] 18...30 DC; (to SELV/PELV)
Current consumption [mA] < 35
Min. insulation resistance [MΩ] 100; (500 V DC)
Protection class III
Reverse polarity protection yes
Power-on delay time [s] 0.3
Integrated watchdog yes
Inputs / outputs
Number of inputs and outputs Number of digital outputs: 2; Number of analogue outputs: 1
Outputs
Total number of outputs 2
Output signal switching signal; analogue signal; IO-Link; (configurable)
Electrical design PNP/NPN
Number of digital outputs 2
Output function normally open / normally closed; (parameterisable)
Max. voltage drop switching
[V] 2
output DC
Permanent current rating of
[mA] 250
switching output DC
Switching frequency DC [Hz] < 500
Number of analogue outputs 1
Analogue current output [mA] 4...20; (scalable 1:5)
Max. load [Ω] 500
Analogue voltage output [V] 0...10; (scalable 1:5)
Min. load resistance [Ω] 2000
Short-circuit protection yes
Type of short-circuit
pulsed
protection
Overload protection yes
Measuring/setting range
Measuring range -1...25 bar -14.5...362.5 psi -0.1...2.5 MPa
Analogue start point -1...20 bar -14.5...290 psi -0.1...2 MPa
Analogue end point 4...25 bar 58...362.5 psi 0.4...2.5 MPa
Factory setting / CMPT = 2
Set point SP -0.85...25 bar -12...362.5 psi -0.085...2.5 MPa
Reset point rP -0.95...24.9 bar -13.5...361 psi -0.095...2.49 MPa
Min. difference between SP 0.15 bar 1.5 psi 0.015 MPa
and rP
In steps of 0.05 bar 0.5 psi 0.005 MPa
Status_B High Resolution / CMPT = 3
Set point SP -0.84...25 bar -12.2...362.6 psi -0.084...2.5 MPa
Reset point rP -0.95...24.9 bar -13.7...361.1 psi -0.095...2.49 MPa
Min. difference between SP 0.11 bar 1.5 psi 0.011 MPa
and rP
In steps of 0.01 bar 0.1 psi 0.001 MPa

ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — PN2293-01 — 21.02.2020 —
PN2293
Pressure sensor with display
PN-025-REN14-MFRKG/US/ /V

Accuracy / deviations
Switch point accuracy
< ± 0,4; (Turn down 1:1)
[% of the span]
Repeatability [% of the span] < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1)
Characteristics deviation < ± 0,25 (BFSL) / < ± 0,5 (LS); (Turn down 1:1; BFSL
[% of the span] = Best Fit Straight Line; LS = limit value setting)
Hysteresis deviation
< ± 0,1; (Turn down 1:1)
[% of the span]
Long-term stability
< ± 0,05; (Turn down 1:1; per 6 months)
[% of the span]
Temperature coefficient zero
point < ± 0,2; (-0...80 °C)
[% of the span / 10 K]
Temperature coefficient span
< ± 0,2; (-0...80 °C)
[% of the span / 10 K]
Notes on the accuracy /
switch point accuracy, linearity error under DNV GL: < ± 1%: < ± 1%
deviation
Response times
Response time [ms] < 1.5
Delay time programmable dS,
[s] 0...50
dr
Damping process value dAP [s] 0...4
Damping for the analogue
[s] 0...4
output dAA
Max. response time analogue
[ms] 3
output
Software / programming
hysteresis / window; normally open / normally closed; switch-on/
Parameter setting options
switch-off delay; Damping; Display unit; current/voltage output
Interfaces
Communication interface IO-Link
Transmission type COM2 (38,4 kBaud)
IO-Link revision 1.1
SDCI standard IEC 61131-9
SIO mode yes
Required master port type A; (when pin 2 not connected: B)
Type of operation DeviceID
Supported DeviceIDs Factory setting / CMPT = 2 472
Status_B High Resolution / CMPT = 3 988
Note For further information please see the IODD PDF file under "Downloads"

ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — PN2293-01 — 21.02.2020 —
PN2293
Pressure sensor with display
PN-025-REN14-MFRKG/US/ /V

Factory setting / CMPT = 2

Profiles Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis
Min. process cycle time [ms] 2.3
IO-Link resolution pressure [bar] 0.01
function bit length
IO-Link process data
pressure 14
(cyclical)
binary switching information 2
IO-Link functions (acyclical) application specific tag
Status_B High Resolution / CMPT = 3
Smart Sensor ED2: Digital Measuring Sensor
Profiles
(0x000A), Identification and Diagnosis (0x4000)
Min. process cycle time [ms] 3
IO-Link resolution pressure [bar] 0.01
function bit length
IO-Link process data pressure 16
(cyclical) device status 4
binary switching information 2
IO-Link functions (acyclical) application specific tag
Operating conditions
Ambient temperature [°C] -25...80
Storage temperature [°C] -40...100
Protection IP 65; IP 67
Tests / approvals
DIN EN 61000-6-2
EMC
DIN EN 61000-6-3
Shock resistance DIN EN 60068-2-27 50 g (11 ms)
Vibration resistance DIN EN 60068-2-6 20 g (10...2000 Hz)
MTTF [years] 138
UL approval UL Approval no. J012
Pressure Equipment Directive Sound engineering practice; can be used for group 2 fluids; group 1 fluids on request
Mechanical data
Weight [g] 223.5
Materials stainless steel (1.4404 / 316L); PBT+PC-GF30; PBT-GF20; PC
Materials (wetted parts) stainless steel (1.4404 / 316L); AI2O3 (96%; ceramics); FKM
Min. pressure cycles 100 million
Tightening torque [Nm] > 50; (depends on lubrication, seal and pressure rating)
Process connection threaded connection 1/4" NPT internal thread
Restrictor element integrated no (can be retrofitted)
Displays / operating elements
Display unit 3 x LED, green (bar, psi, MPa)
Display switching status 2 x LED, yellow
measured values alphanumeric display, red/green 4-digit
Remarks
Pack quantity 1 pcs.

ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — PN2293-01 — 21.02.2020 —
PN2293
Pressure sensor with display
PN-025-REN14-MFRKG/US/ /V

Electrical connection
Connector: 1 x M12; coding: A; Contacts: gold-plated

Connection

OUT1 switching output

IO-Link
OUT2 switching output
analogue output
Core colours :
BK = black
BN = brown
BU = blue
WH = white

ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — PN2293-01 — 21.02.2020 —