ISO-UNI FITTINGS

PVC-C

TemperFIP100® solvent weld fittings, metric series

FITTINGS
ISO-UNI
Series of fittings SOLVENT WELD FITTINGS, METRIC SERIES
designed for
conveying fluids Technical specifications
Size range d 16 ÷ 225 (mm)
under pressure with Nominal pressure PN 16 with water at 20° C
a cold chemical Temperature range 0 °C ÷ 100 °C
Coupling standards Solvent welding: EN ISO 15493
weld jointing system Can be coupled to pipes according to EN ISO 15493

(solvent welding) Flanging system: ISO 7005-1, EN ISO 15493, DIN

2501, ANSI B.16.5 cl. 150
using a suitable Reference standards Construction criteria: EN ISO 15493

solvent cement Test methods and requirements: EN ISO 15493

Installation criteria: DVS 2204, DVS 2221, UNI 11242
(TemperGLUE WELD- Fitting material PVC-C
Seal material EPDM, FPM
ON) and cleaner-
primer.

24
TECHNICAL DATA
REGRESSION CURVE bar
0.1 1 10 102 103 104 105 106 h

FOR PVC-C FITTINGS

50
40 10 °C
Regression coefficients in 30 20 °C
30 °C
accordance with standard EN ISO 25 40 °C
15493 for minimum MRS = 20 N/ 50 °C
mm2 (MPa). 20 60 °C

70 °C
15
80 °C

10
9 90 °C
8
Hoop stress

7
6

5
4
3.5
3
2.5
2

1.5

1 5 10 25 50 100
Years
0.5
Lifetime

PRESSURE VARIATION bar

-40 -20 0 20 40 60 80 100 120 140 °C
ACCORDING TO
TEMPERATURE 16 PN 16

14

For water and non-hazardous fluids 12

for which the material is classified
Working pressure

as CHEMICALLY RESISTANT (life 10 PN 10

expectancy 25 years). In other
cases, a reduction of the nominal 8
pressure PN is required.
Note 6
When using PVC-C at working
temperatures higher than 90°, it is 4
advisable to first contact the service
centre. 2

0
Working temperature

The information in this leaflet is provided in good faith. No liability will be accepted concerning technical data that is not directly covered by
recognised international standards. FIP reserves the right to carry out any modification. Products must be installed and maintained by qualified
personnel.

25
DIMENSIONS
Fig. A

GIC
90° elbow with solvent weld sockets (fig. A)

d PN E L Z g Code

16 16 22 14 9 12 GIC016
20 16 27 16 11.5 20 GIC020
25 16 33 19 14 34 GIC025
32 16 41 22 16.5 56 GIC032
40 16 50 26 22.5 95 GIC040
50 16 61 31 27 155 GIC050
63 16 76 38 33.5 283 GIC063
75 16 91 44 40.3 490 GIC075
90 16 107 51 48 745 GIC090
110 16 130 61 60 1265 GIC110
160 16 193 86 88 4500 GIC160

Fig. B

GIC
90° elbow with solvent weld sockets (fig. B)

d PN E L Z g Code

225 10 258 119 172 9270 GIC225

26
 HIC
45° elbow with solvent weld sockets

d PN E L Z g Code

20 16 28 16 5.5 20 HIC020
25 16 34 19 6 32 HIC025
32 16 42.5 22 7 58 HIC032
40 16 52 26 10.5 101 HIC040
50 16 64 31 11.7 175 HIC050
63 16 80 38 14 305 HIC063
75 16 90 44 17 344 HIC075
90 16 107 51 21.5 587 HIC090
110 16 130 61 26 1007 HIC110
160 16 192 86 38 3255 HIC160
225 10 260 121 55 7150 HIC225

MIC
Solvent weld double socket

d PN E L Z g Code

16 16 22 14 3 9 MIC016
20 16 27 16 3 11 MIC020
25 16 33 19 3 21 MIC025
32 16 41 22 3 31 MIC032
40 16 50 26 3 58 MIC040
50 16 61 31 3 90 MIC050
63 16 75 38 3 160 MIC063
75 16 89 44 3 260 MIC075
90 16 108 51 5 465 MIC090
110 16 130 61 9 750 MIC110
160 16 186 86 9 1820 MIC160
225 10 260 119 11 5360 MIC225

27
 TIC
90° Tee with solvent weld sockets

d PN E L Z g Code

16 16 22 14 9 15 TIC016
20 16 27 16 11 25 TIC020
25 16 33 19 14 45 TIC025
32 16 41 22 17.5 75 TIC032
40 16 50 26 22 125 TIC040
50 16 61 31 27 195 TIC050
63 16 76 38 33.5 394 TIC063
75 16 91 44 38.5 667 TIC075
90 16 109 51 48 1075 TIC090
110 16 133 61 61 1920 TIC110
160 16 192 86 89 5730 TIC160
225 10 258 119 114 10800 TIC225

TRIC
90° reducing Tee with reduced branch and solvent weld sockets

d x d1 PN E E1 L L1 Z Z1 g Code

25 x 20 16 33 28 19 16 14 14 41 TRIC025020
32 x 20 16 41 28 22 16 17.5 17.5 66 TRIC032020
32 x 25 16 41 34 22 19 17.5 17.5 72 TRIC032025
40 x 20 16 50 29 26 16 22 22 111 TRIC040020
40 x 25 16 50 34 26 19 22 22 111 TRIC040025
50 x 25 16 61 35 31 19 27 27 176 TRIC050025
50 x 32 16 61 42 31 22 27 27 182 TRIC050032
63 x 25 16 76 36 38 19 33.5 33.5 320 TRIC063025
63 x 32 16 76 43 38 22 33.5 33.5 325 TRIC063032
75 x 25 16 91 33 44 16 40.5 39 470 TRIC075025
90 x 25 16 109 33 51 16 48.5 46 773 TRIC090025
110 x 25 16 133 33 61 16 61 56 1170 TRIC110025

28
 CIC
End cap with solvent weld socket

d PN E H L g Code

20 16 28 23 16 9 CIC020
25 16 34 27 19 16 CIC025
32 16 41 31 22 25 CIC032
40 16 51 36 26 42 CIC040
50 16 62 43 31 64 CIC050
63 16 77 51 38 115 CIC063
75 16 91 59 44 205 CIC075
90 16 110 69 51 260 CIC090
110 16 132 83 61 555 CIC110

BIC
Union with solvent weld socket, with O-Ring in EPM or FPM

d R1 DN PN E H L Z g EPDM Code FPM Code

16 3/4 10 16 33 41 14 13 23 BIC016E BIC016F

20 1 15 16 41 45 16 13 39 BIC020E BIC020F
25 1”1/4 20 16 50 51 19 13 68 BIC025E BIC025F
32 1”1/2 25 16 58 57 22 13 94 BIC032E BIC032F
40 2 32 16 72 67 26 15 163 BIC040E BIC040F
50 2”1/4 40 16 79 79 31 17 190 BIC050E BIC050F
63 2”3/4 50 16 98 98 38 22 355 BIC063E BIC063F

29
 EFC
Union nut with BSP thread for union types BIC, BIFC, BFC, BLC, BIRC, BIFOC, BIROC,
BIFXC, BIRXC.

R1 d BIC PN E F H g Code

3/4” 16 16 33 22 21 9 EFC034
1” 20 16 41 28 22 13 EFC100
1”1/4 25 16 50 36 25 22 EFC114
1”1/2 32 16 58 42 27 30 EFC112
2” 40 16 72 53 30 50 EFC200
2”1/4 50 16 79 59 34 68 EFC214
2”3/4 63 16 98 74 38 120 EFC234

F/BIC
Union bush for solvent welding, metric series

d R1 PN L Z g Code

16 3/4” 16 14 10 9 FBIC016
20 1” 16 16 10 13 FBIC020
25 1”1/4 16 19 10 25 FBIC025
32 1”1/2 16 22 10 31 FBIC032
40 2” 16 26 12 58 FBIC040
50 2”1/4 16 31 14 63 FBIC050
63 2”3/4 16 38 19 119 FBIC063

30
 Q/BIC
Union end for solvent welding, metric series

d PN d3 d4 L Z g Code

16 16 22 24 14 3 5 QBIC016
20 16 27.5 30.1 16 3 10 QBIC020
25 16 36 38.8 19 3 16 QBIC025
32 16 41.5 44.7 22 3 23 QBIC032
40 16 53 56.5 26 3 40 QBIC040
50 16 59 62.6 31 3 44 QBIC050
63 16 74 78.4 38 3 82 QBIC063

Q/BAC
Union end for solvent welding, ASTM series

d PN d3 d4 L Z g Code

1/2” 16 27.5 30.1 22.7 3.5 17 QBAC012

3/4” 16 36 38.8 25.9 3.7 25 QBAC034
1” 16 41.5 44.7 29.2 3 36 QBAC100
1”1/4 16 53 56.5 32 5 63 QBAC114
1”1/2 16 59 62.6 35 5 86 QBAC112
2” 16 74 78.4 38.5 5.5 143 QBAC200

31
 O-Ring
O-Ring for union types BIC, BIFC, BIFOC, BIFXC, BIRXC

Union d C di T EPDM Code FPM Code

16 3062 15.54 2.62 OR3062E OR3062F

20 4081 20.22 3.53 OR4081E OR4081F
25 4112 28.17 3.53 OR4112E OR4112F
32 4131 32.93 3.53 OR4131E OR4131F
40 6162 40.65 5.34 OR6162E OR6162F
50 6187 47 5.34 OR6187E OR6187F
63 6237 59.69 5.34 OR6237E OR6237F
75 6300 75.57 5.34 OR6300E OR6300F
90 6362 91.45 5.34 OR6362E OR6362F
110 6450 113.67 5.34 OR6450E OR6450F

Fig. A

DIC
Reducing bush with solvent weld spigot (d) and solvent weld socket (d1 reduced) (fig. A)

d x d1 PN L Z g Code

20 x 16 16 16 2 3 DIC020016
25 x 20 16 19 3 6 DIC025020
32 x 20 16 22 6 16 DIC032020
32 x 25 16 22 3 11 DIC032025
40 x 32 16 26 4 18 DIC040032
50 x 40 16 31 5 35 DIC050040
63 x 50 16 38 7 70 DIC063050
75 x 63 16 44 6 92 DIC075063
90 x 75 16 51 7 159 DIC090075
110 x 90 16 61 9 297 DIC110090

32
Fig. B

DIC
Reducing bush with solvent weld spigot (d) and solvent weld socket (d1 reduced) (fig. B)

d x d1 PN L Z g Code

40 x 20 16 26 10 27 DIC040020
40 x 25 16 26 7 26 DIC040025
50 x 32 16 31 9 39 DIC050032
63 x 32 16 38 16 81 DIC063032
63 x 40 16 38 11.5 84 DIC063040
75 x 50 16 44 12 126 DIC075050
90 x 50 16 51 20 213 DIC090050
90 x 63 16 51 13 209 DIC090063
110 x 63 16 61 23 365 DIC110063
110 x 75 16 61 17 386 DIC110075
160 x 110 16 86 25 1040 DIC160110
225 x 160 10 119 33 2100 DIC225160

QRC
Stub with serrated face according to DIN 8063 PN 10/16 with solvent weld socket, for
use with flat gasket (for gasket sizes, see QHV)

d DN PN E F L Sp Z g Code

20 15 16 27 34 16 3.5 3.5 11 QRC020

25 20 16 33 41 19 3 3 17 QRC025
32 25 16 41 50 22 3 3 27 QRC032
40 32 16 50 61 26 3 3 43 QRC040
50 40 16 61 73 31 3 3 66 QRC050
63 50 16 76 90 38 3 3 116 QRC063
75 65 16 90 103 44 3 3 175 QRC075
90 80 16 108 125 51 5 5 305 QRC090
110 100 16 131 150 61 4 4 490 QRC110
160 150 16 188 212 86 4.5 5 1240 QRC160
225 200 10 245 273 119 25 6 1850 QRC225

33
 QHV/X
Flat gasket in EPDM and FPM for flanging system according to DIN 2501, EN 1092

d DN A B Sp EPDM Code FPM Code

20 - 1/2” 15 20 32 2 QHVX020E QHVX020F

25 - 3/4” 20 24 38.5 2 QHVX025E QHVX025F
32 - 1” 25 32 48 2 QHVX032E QHVX032F
40 - 1” 1/4 32 40 59 2 QHVX040E QHVX040F
50 - 1” 1/2 40 50 71 2 QHVX050E QHVX050F
63 - 2” 50 63 88 2 QHVX063E QHVX063F
75 - 2” 1/2 65 75 104 2 QHVX075E QHVX075F
90 - 3” 80 90 123 2 QHVX090E QHVX090F
110 - 4” 100 110 148 3 QHVX110E QHVX110F
125 125 125 166 3 QHVX125E QHVX125F
140 125 140 186 3 QHVX140E QHVX140F
160 - 6” 150 160 211 3 QHVX160E QHVX160F
200 200 200 252 4 QHVX200E -
225 - 8” 200 225 270 4 QHVX225E -

Note: for flat gaskets QHV/X d 250 see PVC-U Fittings Catalogue

QHV/Y
Flat gasket in EPDM for flanging system according to DIN 2501, EN 1092, self-centring
for flanges drilled PN 10/16 up to DN 150 and PN 10 from DN 200

d DN A1 B1 f I U Sp Code

20 - 1/2” 15 17 95 14 65 4 2 QHVY020E
25 - 3/4” 20 22 107 14 76.3 4 2 QHVY025E
32 - 1” 25 28 117 14 86.5 4 2 QHVY032E
40 - 1” 1/4 32 36 142.5 18 101 4 2 QHVY040E
50 - 1” 1/2 40 45 153.3 18 111 4 2 QHVY050E
63 - 2” 50 57 168 18 125.5 4 2 QHVY063E
75 - 2” 1/2 65 71 187.5 18 145.5 4 3 QHVY075E
90 - 3” 80 84 203 18 160 8 3 QHVY090E
110 - 4” 100 102 223 18 181 8 3 QHVY110E
125 125 132 250 18 210 8 3 QHVY125E
140 125 132 250 18 210 8 3 QHVY140E
160 - 6” 150 152 288.5 22 241.5 8 4 QHVY160E
200 200 192 340 22 295 8 4 QHVY200E
225 - 8” 200 215 340 22 295 8 4 QHVY225E

Note: for flat gaskets QHV/Y from d250 to d400, see PVC-U Fittings Catalogue

34
 ODC
Backing ring in PVC-C for stubs QRC EN/ISO/DIN.
Drilling: PN10 up to DN100

*PMA
d DN b d2 d6 D K M n **(Nm) g Code
(bar)
20 15 10 11 14 28 96 65 M12x70 4 10 66 ODC020
25 20 10 12 14 34 107 75 M12x70 4 10 93 ODC025
32 25 10 14 14 42 116 85 M12x70 4 10 122 ODC032
40 32 10 15 18 51 142 100 M16x85 4 13 200 ODC040
50 40 10 16 18 62 153 110 M16x85 4 13 245 ODC050
63 50 10 18 18 78 168 125 M16x95 4 15 310 ODC063
75 65 10 19 18 91 188 145 M16x95 4 17 425 ODC075
90 80 10 20 18 109 199 160 M16x105 8 18 455 ODC090
110 100 10 22 18 132 219 180 M16x105 8 20 545 ODC110

*PMA maximum admissible working pressure

**nominal tightening torque

ODB
Steel core backing ring, PP/FRP coated, according to EN/ISO/DIN for stubs QRC
Drilled PN 10/16 up to DN 150

*PMA
d DN b d2 d6 D k M n **(Nm) g Code
(bar)
20 15 16 12 14 28 95 65 M12 4 15 290 ODB020
25 20 16 14 14 34 105 75 M12 4 15 410 ODB025
32 25 16 14 14 42 115 85 M12 4 15 610 ODB032
40 32 16 16 18 51 140 100 M16 4 20 880 ODB040
50 40 16 16 18 62 150 110 M16 4 30 810 ODB050
63 50 16 19 18 78 165 125 M16 4 35 940 ODB063
75 65 16 19 18 92 185 145 M16 4 40 1210 ODB075
90 80 16 21 18 109 200 160 M16 8 40 1480 ODB090
***125 100 16 22 18 134 220 180 M16 8 40 1570 ODB125
****180 150 16 27 22 191 285 240 M20 8 60 3470 ODB180

*maximum admissible pressure values according to EN/ISO/DIN.

** nominal tightening torque
*** for use with stubs QRC110
*** for use with stubs QRC160

35
 ODB-SW
Steel core backing ring, PP/FRP coated, according to EN/ISO/DIN for stubs QRC

*PMA
d DN b d2 d6 D k M n **(Nm) g Code
(bar)
225 200 16 27 22 247 340 295 M20 8 75 5060 SWODBD225DN200

*PMA maximum admissible working pressure

**nominal tightening torque

OAB
Steel core backing ring, PP/FRP coated according to ANSI B16.5 cl.150 for stubs QRC

*PMA mm inch mm inch

d DN b d6 D n **(Nm) g Code
(bar) d2 d2 K K
1/2” 15 16 12 16 5/8” 28 95 60.45 2”3/8 4 15 220 OAB012
3/4” 20 16 12 16 5/8” 34 102 69.85 2”3/4 4 15 240 OAB034
1” 25 16 16 16 5/8” 42 114 79.25 3”1/8 4 15 390 OAB100
1”1/4 32 16 16 16 5/8” 51 130 88.9 3”1/2 4 25 510 OAB114
1”1/2 40 16 18 16 5/8” 62 133 98.55 3”7/8 4 35 580 OAB112
2” 50 16 18 20 3/4” 78 162 120.65 4”3/4 4 35 860 OAB200
2”1/2 65 16 18 20 3/4” 92 184 139.7 5”1/2 4 40 1100 OAB212
3” 80 16 18 20 3/4” 111 194 152.4 6” 4 40 1040 OAB300
4” 100 16 18 20 3/4” 133 229 190.5 7”1/2 8 40 1620 OAB400

*PMA maximum admissible working pressure

**nominal tightening torque

36
 ODBC
Steel core blind flange, PP/FRP coated, according to EN/ISO/DIN Drilling: PN 10/16

*PMA
d DN b d2 D k M n **(Nm) g Code
(bar)
20 15 16 12 14 95 65 M12 4 15 290 ODBC020
25 20 16 12 14 105 75 M12 4 15 390 ODBC025
32 25 16 16 14 115 85 M12 4 15 550 ODBC032
40 32 16 16 18 140 100 M16 4 25 820 ODBC040
50 40 16 16 18 150 110 M16 4 35 900 ODBC050
63 50 16 16 18 165 125 M16 4 35 1150 ODBC063
75 65 16 18 18 185 145 M16 4 40 1680 ODBC075
90 80 16 18 18 200 160 M16 8 40 2240 ODBC090
110/125 100 16 20 18 220 180 M16 8 40 2800 ODBC110
160/180 150 16 24 22 285 240 M20 8 60 5080 ODBC160

*PMA maximum admissible working pressure

**nominal tightening torque

OABC
Steel core blind flange, PP/FRP coated according to ANSI B16.5 cl.150

*PMA mm inch mm inch

d DN b D n **(Nm) g Code
(bar) d2 d2 K K
1/2” 15 16 12 16 5/8” 95 60.45 2”3/8 4 15 200 OABC012
3/4” 20 16 12 16 5/8” 102 69.85 2”3/4 4 15 240 OABC034
1” 25 16 16 16 5/8” 114 79.25 3”1/8 4 15 370 OABC100
1”1/4 32 16 16 16 5/8” 130 88.90 3”1/2 4 25 530 OABC114
1”1/2 40 16 18 16 5/8” 133 98.55 3”7/8 4 35 560 OABC112
2” 50 16 18 20 3/4” 162 120.65 4”3/4 4 35 810 OABC200
2”1/2 65 16 18 20 3/4” 184 139.70 5”1/2 4 40 1070 OABC212
3” 80 16 18 20 3/4” 194 152.40 6” 4 40 1030 OABC300
4” 100 16 18 20 3/4” 229 190.50 7”1/2 8 40 1570 OABC400

*PMA maximum admissible working pressure

**nominal tightening torque

37
ISO-BSP FITTINGS
PVC-C

TemperFIP100® adapter fittings

FITTINGS
ISO-BSP
Series of fittings TemperFIP100® ADAPTOR FITTINGS
designed for
conveying Technical specifications

fluids under pressure Size range

Nominal pressure
d 16 ÷ 63 (mm); R 3/8” ÷ 2”
PN 16 with water at 20° C
with threaded and Temperature range 0 °C ÷ 100 °C
Coupling standards Solvent welding: EN ISO 15493
cold chemical solvent Can be coupled to pipes according to EN ISO 15493
weld jointing systems Thread: ISO 228-1, DIN 2999
Reference standards Construction criteria: EN ISO 15493
(solvent welding) Test methods and requirements: EN ISO 15493

using suitable solvent Fitting material Installation criteria: DVS 2204, DVS 2221, UNI 11242
PVC-C
cement (TemperGLUE Seal material EPDM, FPM

WELD-ON) and
cleaner-primer.

40
TECHNICAL DATA
REGRESSION CURVE bar
0.1 1 10 102 103 104 105 106 h

FOR PVC-C FITTINGS

50
40 10 °C
Regression coefficients in 30 20 °C
30 °C
accordance with standard EN ISO 25 40 °C
15493 for minimum MRS = 20 N/ 50 °C
mm2 (MPa). 20 60 °C

70 °C
15
80 °C

10
9 90 °C
8
Hoop stress

7
6

5
4
3.5
3
2.5
2

1.5

1 5 10 25 50 100
Years
0.5
Lifetime

PRESSURE VARIATION bar

-40 -20 0 20 40 60 80 100 120 140 °C
ACCORDING TO
TEMPERATURE 16 PN 16

14

For water and non-hazardous fluids 12

for which the material is classified
Working pressure

as CHEMICALLY RESISTANT (life 10 PN 10

expectancy 25 years). In other
cases, a reduction of the nominal 8
pressure PN is required.
Note 6
When using PVC-C at working
temperatures higher than 90°, it is 4
advisable to first contact the service
centre. 2

0
Working temperature

The information in this leaflet is provided in good faith. No liability will be accepted concerning technical data that is not directly covered by
recognised international standards. FIP reserves the right to carry out any modification. Products must be installed and maintained by qualified
personnel.

41
DIMENSIONS

GIMC
90° elbow with reinforced solvent weld socket d and BSP threaded female end R with
STAINLESS steel reinforcing ring

dxR PN E E1 L L1 Z Z1 g Code

16 x 3/8” 16 23.5 24.5 14 11.4 10 13 22 GIMC016038

20 x 1/2” 16 28.5 29.5 16 15 12 13 33 GIMC020012
25 x 3/4” 16 35 36 19 16.3 14 17 53 GIMC025034
32 x 1” 16 43 44 22 19.1 18 20.5 94 GIMC032100
40 x 1” 1/4 16 50 51 26 21.4 22 27 104 GIMC040114
50 x 1” 1/2 16 61 62 31 21.4 27 37 203 GIMC050112
63 x 2” 16 76 77 38 25.7 33 46 380 GIMC063200

TIMC
90° Tee with reinforced solvent weld socket d and BSP threaded female end R with
STAINLESS steel reinforcing ring

dxR PN E E1 L L1 Z Z1 g Code

16 x 3/8” 16 23.5 24.5 14 11.4 9 11 25 TIMC016038

20 x 1/2” 16 28.5 29.5 16 15 12 13 40 TIMC020012
25 x 3/4” 16 35 36 19 16.3 15 17 63 TIMC025034
32 x 1” 16 43 44 22 19.1 18 21 118 TIMC032100
40 x 1” 1/4 16 50 51 26 21.4 21.5 27 137 TIMC040114
50 x 1” 1/2 16 61 62 31 21.4 27 37 231 TIMC050112
63 x 2” 16 76 77 38 25.7 33.5 46 457 TIMC063200

MIMC
Double socket with solvent weld socket d and BSP threaded female end r with
STAINLESS steel reinforcing ring

dxR PN E E1 K L L1 Z g Code

16 x 3/8” 16 23.5 24.5 24 14 11.4 5.6 15 MIMC016038

20 x 1/2” 16 28.5 29.5 29 16 15 4 25 MIMC020012
25 x 3/4” 16 35 36 35 19 16.3 5 38 MIMC025034
32 x 1” 16 43 44 43 22 19.1 6 58 MIMC032100
40 x 1” 1/4 16 50 51 50 26 21.4 5 66 MIMC040114
50 x 1” 1/2 16 61 62 61 31 21.4 8 109 MIMC050112
63 x 2” 16 76 77 76 38 25.7 7.5 196 MIMC063200

42
 KIFC
Double adaptor with solvent weld socket df, solvent weld spigot dm and BSP threaded
male end R

dm x df x R PN K L1 Lf Lm Z g Code

20 x 16 x 3/8” 16 24 11,4 14 16 25,5 7 KIFC020016038

25 x 20 x 1/2” 16 30 15 16 19 30 16 KIFC025020012
32 x 25 x 3/4” 16 34 16,3 19 22 27,5 23 KIFC032025034
40 x 32 x 1” 16 42 19,1 22 26 32 38 KIFC040032100
50 x 40 x 1” 1/4 16 52 21,4 26 31 35,5 65 KIFC050040114
63 x 50 x 1” 1/2 16 65 21,4 31 38 39,5 113 KIFC063050112
75 x 63 x 2” 16 75 25,7 38 44 43 158 KIFC075063200

BIFC
Union with solvent weld socket d and BSP threaded female end R with O-ring in
EPDM

dxR R1 PN E H L L1 Z g Code

16 x 3/8” 3/4” 16 33 41 14 11.4 15.6 25 BIFC016038E

20 x 1/2” 1” 16 41 45 16 15 14 40 BIFC020012E
25 x 3/4” 1”1/4 16 51 51 19 16.3 15.7 68 BIFC025034E
32 x 1” 1”1/2 16 58 57 22 19.1 15.9 93 BIFC032100E
40 x 1” 1/4 2” 16 72 67 26 21.4 19.6 158 BIFC040114E
50 x 1” 1/2 2”1/4 16 79 72 31 21.4 19.6 193 BIFC050112E
63 x 2” 2”3/4 16 98 88 38 25.7 24 345 BIFC063200E

43
 BIFOC
Adaptor union in PVC-C/brass with solvent weld socket d and BSP threaded brass
female end R with O-Ring in EPDM

dxR R1 PN E H K L L1 Z g Code

16 x 3/8” 3/4” 16 33 45.5 20 14 13.5 18 55 BIFOC016038E

20 x 1/2” 1” 16 41 48.5 25 16 16.5 16 88.5 BIFOC020012E
25 x 3/4” 1”1/4 16 50 54.5 32 19 18.5 17 165 BIFOC025034E
32 x 1 “ 1”1/2 16 58 59.5 38 22 19.5 18 187 BIFOC032100E
40 x 1” 1/4 2” 16 72 68.5 48 26 21.5 21 379 BIFOC040114E
50 x 1” 1/2 2”1/4 16 79 84.5 55 31 23 30.5 475 BIFOC100112E
63 x 2” 2”3/4 16 98 94.5 69 38 27 29.5 837 BIFOC063200E

BIROC
Adaptor union in PVC-C/brass with solvent weld socket d and BSP threaded brass male
end R with O-Ring in EPDM

dxR R1 PN E H K L L1 Z g Code

16 x 3/8” 3/4” 16 33 58.5 20 14 10.5 34 81 BIROC016038E

20 x 1/2” 1” 16 41 65 25 16 13.5 35.5 133.5 BIROC020012E
25 x 3/4” 1”1/4 16 50 72.5 32 19 15 38.5 223 BIROC025034E
32 x 1” 1”1/2 16 58 80 38 22 17.5 40.5 294 BIROC032100E
40 x 1” 1/4 2” 16 72 91 48 26 19.5 45.5 558 BIROC040114E
50 x 1” 1/2 2”1/4 16 79 101 55 31 19.5 50.5 696 BIROC100112E
63 x 2” 2”3/4 16 98 122.5 69 38 24 60.5 1196 BIROC063200E

44
 BIFXC
Adaptor union in PVC-C/STAINLESS steel with solvent weld socket d and BSP threaded
STAINLESS steel female end R with O-Ring in EPDM or FPM

dxR R1 PN E H K L L1 Z g EPDM Code FPM Code

16 x 3/8” 3/4” 16 33 45.5 20 14 13.5 18 52 BIFXC016038E BIFXC016038F

20 x 1/2” 1” 16 41 48.5 25 16 16.5 16 83.5 BIFXC020012E BIFXC020012F
25 x 3/4” 1”1/4 16 50 54.5 32 19 18.5 17 156 BIFXC025034E BIFXC025034F
32 x 1 “ 1”1/2 16 58 59.5 38 22 19.5 18 176 BIFXC032100E BIFXC032100F
40 x 1” 1/4 2” 16 72 68.5 48 26 21.5 21 361 BIFXC040114E BIFXC040114F
50 x 1” 1/2 2”1/4 16 79 84.5 55 31 23 30.5 450 BIFXC100112E BIFXC100112F
63 x 2” 2”3/4 16 98 94.5 69 38 27 29.5 792 BIFXC063200E BIFXC063200F

BIRXC
Adaptor union in PVC-C/STAINLESS steel with solvent weld socket d and BSP threaded
STAINLESS steel male end R with O-Ring in EPDM or FPM

dxR R1 PN E H K L L1 Z g EPDM Code FPM Code

16 x 3/8” 3/4” 16 33 58.5 20 14 10.5 34 76 BIRXC016038E BIRXC016038F

20 x 1/2” 1” 16 41 65 25 16 13.5 35.5 125.5 BIRXC020012E BIRXC020012F
25 x 3/4” 1”1/4 16 50 72.5 32 19 15 38.5 219 BIRXC025034E BIRXC025034F
32 x 1” 1”1/2 16 58 80 38 22 17.5 40.5 275 BIRXC032100E BIRXC032100F
40 x 1” 1/4 2” 16 72 91 48 26 19.5 45.5 524 BIRXC040114E BIRXC040114F
50 x 1” 1/2 2”1/4 16 79 101 55 31 19.5 50.5 654 BIRXC100112E BIRXC100112F
63 x 2” 2”3/4 16 98 122.5 69 38 24 60.5 1124 BIRXC063200E BIRXC063200F

45
 EFC
Union nut with BSP thread for union types BIC, BIFC, BFC, BLC, BIRC, BIFOC, BIROC,
BIFXC, BIRXC.

R1 d BIC PN E F H g Code

3/4” 16 16 33 22 21 9 EFC034
1” 20 16 41 28 22 13 EFC100
1”1/4 25 16 50 36 25 22 EFC114
1”1/2 32 16 58 42 27 30 EFC112
2” 40 16 72 53 30 50 EFC200
2”1/4 50 16 79 59 34 68 EFC214
2”3/4 63 16 98 74 38 120 EFC234

F/BIC
Union bush for solvent welding, metric series

d R1 PN L Z g Code

16 3/4” 16 14 10 9 FBIC016
20 1” 16 16 10 13 FBIC020
25 1”1/4 16 19 10 25 FBIC025
32 1”1/2 16 22 10 31 FBIC032
40 2” 16 26 12 58 FBIC040
50 2”1/4 16 31 14 63 FBIC050
63 2”3/4 16 38 19 119 FBIC063

46
 Q/BIC
Union end for solvent welding, metric series

d PN d3 d4 L Z g Code

16 16 22 24 14 3 5 QBIC016
20 16 27.5 30.1 16 3 10 QBIC020
25 16 36 38.8 19 3 16 QBIC025
32 16 41.5 44.7 22 3 23 QBIC032
40 16 53 56.5 26 3 40 QBIC040
50 16 59 62.6 31 3 44 QBIC050
63 16 74 78.4 38 3 82 QBIC063

Q/BAC
Union end for solvent welding, ASTM series

d PN d3 d4 L Z g Code

1/2” 16 27.5 30.1 22.7 3.5 17 QBAC012

3/4” 16 36 38.8 25.9 3.7 25 QBAC034
1” 16 41.5 44.7 29.2 3 36 QBAC100
1”1/4 16 53 56.5 32 5 63 QBAC114
1”1/2 16 59 62.6 35 5 86 QBAC112
2” 16 74 78.4 38.5 5.5 143 QBAC200

47
 Q/BFC
Union end with BSP female thread

R PN d3 d4 L Z g Code

3/8” 16 22 24 11.4 4.5 5 QBFC038

1/2” 16 27.5 30.1 15 5 9 QBFC012
3/4” 16 36 38.8 16.3 5 17 QBFC034
1” 16 41.5 44.7 19.1 5.5 23 QBFC100
1”1/4 16 53 56.5 21.4 5.5 37 QBFC114
1”1/2 16 59 62.6 21.4 5.5 44 QBFC112
2” 16 74 78.4 25.7 5.5 79 QBFC200

Q/BNC
Union end with NPT female thread

R PN d3 d4 L Z g Code

3/8” 16 22 24 12.7 6.3 11 QBNC038

1/2” 16 27.5 30.1 17.8 5.2 17 QBNC012
3/4” 16 36 38.8 18 5.2 22 QBNC034
1” 16 41.5 44.7 22.6 5.7 33 QBNC100
1”1/4 16 53 56.5 25.1 7.3 61 QBNC114
1”1/2 16 59 62.6 24.7 7 77 QBNC112
2” 16 74 78.4 29.6 7.8 127 QBNC200

48
 Q/BFO
Union end in brass with female BSP thread

R d3 d4 H L1 g Code

3/8” 22 24 21.5 13.5 38 QBFO038

1/2” 27.5 30.1 22.5 16.5 60 QBFO012
3/4” 36 38.8 25.5 18.5 116 QBFO034
1” 41.5 44.7 27.5 19.5 144 QBFO100
1”1/4 53 56.5 30.5 21.5 260 QBFO114
1”1/2 59 62.6 33.5 23 325 QBFO112
2” 74 78.4 38.5 27 578 QBFO200

Q/BRO
Union end in brass with male BSP thread

R d3 d4 H L1 g Code

3/8” 22 24 34.5 10.5 64 QBRO038

1/2” 27.5 30.1 39 13.5 105 QBRO012
3/4” 36 38.8 43.5 15 184 QBRO034
1” 41.5 44.7 48 17.5 251 QBRO100
1”1/4 53 56.5 53 19.5 437 QBRO114
1”1/2 59 62.6 56 19.5 545 QBRO112
2” 74 78.4 65.5 24 937 QBRO200

49
 Q/BFX
Union end in A316L stainless steel with female BSP thread

R d3 d4 H L1 g Code

3/8” 22 24 21.5 13.5 34 QBFX038

1/2” 27.5 30.1 22.5 16.5 54 QBFX012
3/4” 36 38.8 25.5 18.5 104 QBFX034
1” 41.5 44.7 27.5 19.5 130 QBFX100
1”1/4 53 56.5 30.5 21.5 234 QBFX114
1”1/2 59 62.6 33.5 23 293 QBFX112
2” 74 78.4 38.5 27 520 QBFX200

Q/BRX
Union end in A316L stainless steel with male BSP thread

R d3 d4 H L1 g Code

3/8” 22 24 34.5 10.5 58 QBRX038

1/2” 27.5 30.1 39 13.5 95 QBRX012
3/4” 36 38.8 43.5 15 166 QBRX034
1” 41.5 44.7 48 17.5 226 QBRX100
1”1/4 53 56.5 53 19.5 393 QBRX114
1”1/2 59 62.6 56 19.5 491 QBRX112
2” 74 78.4 65.5 24 843 QBRX200

50
 O-Ring
O-Ring for union types BIC, BIFC, BIFOC, BIFXC, BIRXC

Union d C di T EPDM Code FPM Code

16 3062 15.54 2.62 OR3062E OR3062F

20 4081 20.22 3.53 OR4081E OR4081F
25 4112 28.17 3.53 OR4112E OR4112F
32 4131 32.93 3.53 OR4131E OR4131F
40 6162 40.65 5.34 OR6162E OR6162F
50 6187 47 5.34 OR6187E OR6187F
63 6237 59.69 5.34 OR6237E OR6237F
75 6300 75.57 5.34 OR6300E OR6300F
90 6362 91.45 5.34 OR6362E OR6362F
110 6450 113.67 5.34 OR6450E OR6450F

51