Scribd
Upload
86 views

ECPC Assignment 1 - Hardware - With Ans

This document provides instructions for a laboratory experiment involving an embedded controllers course. It includes: 1. Questions about the specifications of a TMS320F28379D microcontroller, including supply voltages, current draw, and pin configurations. 2. Objectives for building circuits using the microcontroller, including a 6-channel digital input board, 6-channel digital output board, and 4-channel analog input board. 3. Specifications for each circuit to be built, such as input/output voltage levels, number of channels, and components to use.

Uploaded by

Yashwin.v Yashu
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
86 views

ECPC Assignment 1 - Hardware - With Ans

This document provides instructions for a laboratory experiment involving an embedded controllers course. It includes: 1. Questions about the specifications of a TMS320F28379D microcontroller, including supply voltages, current draw, and pin configurations. 2. Objectives for building circuits using the microcontroller, including a 6-channel digital input board, 6-channel digital output board, and 4-channel analog input board. 3. Specifications for each circuit to be built, such as input/output voltage levels, number of channels, and components to use.

Uploaded by

Yashwin.v Yashu
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

USN

THE NATIONAL INSTITUTE OF ENGINEERING, MYSURU


(Autonomous under VTU)

Embedded Controllers for Power Converters (Code: EE6E112)


Laboratory Experiment-1

Name of the student: USN:

Date: Time:

Read the data sheet of TMS320F28379D (SPRS880K) and answer the following: -

Please indicate the document number/page number/section/sub-section/table number from


where you have picked up the particular information.

1. What is the nominal supply for a) CORE b) I/O Modules


Core : 1.2V
Module : 3.3V (Page 1)
2. What is the maximum supply current required to power the core? At what CPU
frequency and the ambient temperature does this specification is given for?
0.48A, 2000Mhz,(page 54)
3. What is the (a) supply currents and (b) power when the core runs at 50MHz
0.25A, 0.5W (page 54) graph.
4. What is the minimum rate core supply voltage (VDD) can be ramped from zero to
nominal voltage?
330V/s (page 60)
5. List the VDD, VSS pins(labels). What is the suggested value of the decoupling
capacitance?
VDD ,VDDA ,VDDIO ,VDD3VFL ,VDDOSC ,VSS ,VSSA and VSSOSC (page 48).
a minimum 0.1-µF decoupling capacitor on each 3.3V pins and 20µF on 1.2V pins (page
37 and 36).

6. A 10MHz crystal is used to provide the clock source. Draw the schematic to configure
the clock source. What is the range of load capacitances? What is the allowed frequency
range of crystal?
USN

(page 67)

Load capacitance 12 24 pF
Range of frequency : 10-20Mhz (page 68)
7. Draw the schematic of the RESET pin.

Laboratory work
Objective of this exercise include learning of following things: -

1. Usage of instruments Multimeters, CRO and other tools


2. Soldering, de-soldering of component on the PCBs. Usage of various tools like, soldering iron, de-
soldering pumps, wire cutters, nose pliers etc
3. Assembly of the components on the GPCB/Bread board (at least one circuit/project given), testing and
validation of the design.
4. Building of simple electronic circuits used for reading/writing Analog/Digital input/output signals using
Digital Signal controller.

Build and test the following circuits: -

1. Design, build and test a 6-channel digital input circuit/board with following specifications:
a. Type of input: Potential free push buttons
b. No of channels: 6
c. Input logic voltage level: 0-5.0V
d. Output logic voltage level: 0-3.3V
e. Select a output pull up resistor such that the output signal level is more than
Minimum VoH when driving a gate with an input impedance of 100kOhms
f. Select a input pull down resistor such input signal level is less than Maximum V IL
when sinking current is 1.4mA
USN

2. Design, build and test a six channel digital output circuit/board with following
specifications:
a. Output load: LEDs
b. No of channels: 6
c. Input logic voltage level: 0-3.3V
d. Output logic voltage level: 0-5.0V
e. Select a output pull up resistor to drive the LEDs whose minimum drive current
is 1mA
f. Select a input pull down resistor such input signal level is less than Maximum V IL
when sinking current is 1.4mA
USN

3. Design, build and test a six channel analog input circuit/board with following
specifications:
a. Output load: LEDs
b. No of channels: 4
c. Input logic voltage level: 0-1.1V
d. Output logic voltage level: 0-3.3V
e. Provide potentiometers for varying the input analog signals.

You might also like