ELNEC s. r. o.

User's Manual for

JetProg
multiprogramming
system

ELNEC s.r.o.
Presov, Slovakia
February 2003

1
 ELNEC s. r. o.

COPYRIGHT  1997 - 2003

ELNEC s.r.o.
This document is copyrighted by ELNEC s.r.o, Presov, Slovakia. All
rights reserved. This document or any part of it may not be copied,
reproduced or translated in any form or in any way without the prior
written permission of ELNEC s.r.o.

The control program is copyright ELNEC s.r.o., Presov, Slovakia. The

control program or any part of it may not be analyzed, disassembled or
modified in any form, on any medium, for any purpose.

Information provided in this manual is intended to be accurate at the

moment of release, but we continuously improve all our products.
Please consult manual on www.elnec.com.

ELNEC s.r.o. assumes no responsibility for misuse of this manual.

ELNEC s.r.o. reserves the right to make changes or improvements to

the product described in this manual at any time without notice. This
manual contains names of companies, software products, etc., which
may be trademarks of their respective owners. ELNEC s.r.o. respects
those trademarks

2
 ELNEC s. r. o.

How to use this manual

This manual explains how to
use your JetProg
multiprogramming system Dear customer,
and how to install the control
program. This manual is thank you for
complete only with manual purchasing one of the
for JetProg programmer and ELNEC product.
family&socket submodule. It
is assumed that the user has some experience with PCs and
installation of software. Once you have installed the control
program we recommend you consult the context sensitive
HELP within the control program rather than the printed User's
Manual. Revisions are implemented in the context sensitive
help before the printed Users Manual.

General notes
Before installing and using your JetProg multiprogramming
system, please carefully check that your package includes all,
that is said in part Common technical specification. If you
find any discrepancy with respective parts list and/or if any of
these items are damaged, please contact your distributor
immediately.

Please avoid removing/inserting family&socket submodules if

not necessary. The operation live of module/submodule
contact is limited. Damaging of contacts may cause unreliable
works with programmed devices.
Insert same family&socket submodules to appropriate
multiprogramming module connectors very carefully, to avoid
bad insertion of them.

For following text term multiprogramming module means

Common multiprogramming module no.1 or EPROM/Flash 8-
socket module.

Download please actual version of manual from

ELNEC WEB site (www.elnec.com) if current one
will be out of date.

3
 ELNEC s. r. o.

Table of contents
How to use this manual.................................................................. 3
General notes ................................................................................ 3
Introduction .................................................................................... 4
EPROM / EEPROM / Flash EPROM multiprogramming ................ 7
Introduction .................................................................................... 8
EPROM / EEPROM / Flash EPROM multiprogramming elements 9
Technical specification................................................................. 10
MCS-51 series microcontrollers multiprogramming................... 11
Introduction .................................................................................. 12
MCS-51 series microcontrollers multiprogramming elements ..... 13
Technical specification................................................................. 14
PICmicro microcontrollers multiprogramming ........................... 15
Introduction .................................................................................. 16
PICmicro microcontrollers multiprogramming elements .............. 17
Technical specification................................................................. 18
Software .......................................................................................... 19
Common notes ............................................................................... 25
Common technical specification .................................................. 26
Connecting multiprogramming module to JetProg....................... 28
Appendix ......................................................................................... 29
Accepted family&socket submodule ............................................ 30

Introduction
JetProg multiprogramming system is high throughput
manual operated multiprogramming solution convenient for
medium volume production application.

JetProg multiprogramming system consists of JetProg,

multiprogramming module and family&socket submodules.

JetProg multiprogramming system performs programming

verification at the marginal level of supply voltage (it’s depend
of programming devices), which, obviously, improves
programming yield, and guarantees long data retention.

JetProg multiprogramming system is driven by an easy-to-

use WIN-95/98/ME/NT/2000/XP compatible control program
with pull-down menu, hot keys and on-line help. Selecting of
device is performed by its class, by manufacturer or simply by
typing a fragment of vendor name and/or part number.
Standard device-related commands (read, blank check,
program, verify, erase) are boosted by some test functions
(insertion test, signature-byte check). All known data formats
are supported. Automatic file format detection and conversion
during load of file.

4
 ELNEC s. r. o.

The rich-featured auto-increment function enables to assign

individual serial numbers to each programmed device - or
simply increments a serial number, or the function enables to
read serial numbers or any programmed device identification
signatures from a file. This function is not allowed for all type of
programmed devices.

Advanced design, original brand components and careful

manufacturing allow us to provide a two-year warranty on
parts and labor for the multiprogramming modules and
family&socket submodules (limited cycle warranty on ZIF
socket – it is different for any type of ZIF).

JetProg multiprogramming system currently offers following

multiprogramming solutions:

• EPROM/EEPROM/Flash EPROM multiprogramming

• MCS-51 series microcontrollers multiprogramming
• PICmicro microcontrollers multiprogramming

5
 ELNEC s. r. o.

EPROM / EEPROM / Flash

EPROM
multiprogramming

7
 ELNEC s. r. o.

Introduction
EPROM / EEPROM / Flash EPROM multiprogramming
supports byte-wide EPROM, EEPROM and Flash EPROM up
to 8Mbit size, up to 8 devices simultaneously. The replaceable
family&socket submodule permits different package type
support. There are available family&socket submodules for
different packages.

EPROM / EEPROM / Flash EPROM multiprogramming has

optimized EPROM, EEPROM and Flash EPROM pindriver that
deliver programming performance without overshoot or ground
bounce for all memory technologies. Pin drivers operate down
to 1.8V so you'll be ready to program the full range of today's
advanced low-voltage devices.

EPROM / EEPROM / Flash EPROM multiprogramming

provides very competitive price but excellent hardware design
for reliable programming.

8
 ELNEC s. r. o.

EPROM / EEPROM / Flash EPROM

multiprogramming elements
! submodule for EPROM / EEPROM / Flash EPROM with
two ZIF (Zero Insertion Force)
# Common multiprogramming module no.1 (or EPROM/Flash
8-socket module)
$ JetProg, base unit

Problems related to the JetProg ⇔

multiprogramming module ⇔ family&socket
submodule interconnection
If you have any problems with JetProg ⇔ multiprogramming
module ⇔ family&socket submodule interconnection see
section Common notes.

9
 ELNEC s. r. o.

Technical specification
• EPROM/EEPROM/Flash compatible pindriver (8x)
• pindrivers are independent, therefore defective chip haven't
influence to another programmed chips
• perfect ground and necessary supply/programming voltage
can be applied independently to each socket of module
• TTL pindriver meet EPROM/EEPROM/Flash requirements
• current limitation for each socket, overcurrent shutdown,
power failure shutdown
• banana hole for ESD wrist straps
• insertion test

Accepted family&socket submodules

For list and short descriptions of accepted family&socket
submodules see at Appendix.

DEVICE SUPPORT
• EPROM: NMOS/CMOS 27xxx and 27Cxxx series, with 8 bit
data width, full support for LV series
• EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series,
with 8 bit data width
• Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx,
29Wxxx, 49Fxxx series, with 8 bit data width, full support for
LV series
Check please the list of all supported devices for details.

Programming speed
Note:
• given values are measured under all 8 devices together
condition
• these times strongly depend on PC speed, LPT port type and
operating system free resources. Therefore values of two
different PC configuration are given for comparison
Device Operation Time A Time B
27C010 programming and verify 43 sec 28 sec
AT29C040A programming and verify 55 sec 40 sec
AM29F040 programming and verify 98 sec 86 sec

Time A conditions: Pentium MMX, 250 MHz, ECP/EPP,

WIN98.
Time B conditions: Athlon, 750 MHz, ECP/EPP on PCI
bus, WIN98.
For other specification see on Common notes / Common
technical specification

10
 ELNEC s. r. o.

MCS-51 series
microcontrollers
multiprogramming

11
 ELNEC s. r. o.

Introduction
MCS-51 series microcontrollers multiprogramming
supports MCS51 compatible microcontrollers of various
manufacturers, based on both EPROM and Flash technology,
up to 8 devices simultaneously. The replaceable family&socket
submodule permits different package type support. There are
available family&socket submodules for DIL40 and other
packages.

MCS-51 series microcontrollers multiprogramming has

optimized advanced pindriver that deliver programming
performance without overshoot or ground bounce for all
memory technologies. Pin drivers operate down to 1.8V so
you'll be ready to program the full range of today's advanced
low-voltage devices.

MCS-51 series microcontrollers multiprogramming

provides very competitive price but excellent hardware design
for reliable programming.

12
 ELNEC s. r. o.

MCS-51 series microcontrollers

multiprogramming elements
! submodule for MCS-51 series microcontrolllers with two
ZIF (Zero Insertion Force)
# Common multiprogramming module no.1
$ JetProg, base unit

Note: please call for other family&socket submodules

availability

Problems related to the JetProg ⇔

multiprogramming module ⇔ family&socket
submodule interconnection
If you have any problems with JetProg ⇔ multiprogramming
module ⇔ family&socket submodule interconnection see
section Common notes.

13
 ELNEC s. r. o.

Technical specification
• MCS-51series microcontroller compatible pindriver (8x)
• pindrivers are independent, therefore defective chip haven't
influence to another programmed chips
• perfect ground and necessary supply/programming voltage
can be applied independently to each socket of module
• TTL pindriver meet MCS-51series microcontroller
requirements
• current limitation for each socket, overcurrent shutdown,
power failure shutdown
• banana hole for ESD wrist straps
• insertion test

Accepted family&socket submodules

For list and short descriptions of accepted family&socket
submodules see at Appendix.

DEVICE SUPPORT
• EPROM based MCS51 chips: 87C5x series
• Flash based MCS51 chips: 89C5x series
• supported manufacturers: AMD, Atmel, Dallas, ICSI, Intel,
ISSI, Philips, SST, Signetics, Winbond, ...
Check please the list of all supported devices for details.

Programming speed
Notes:
• given values are measured under all 8 devices together
condition
• this times strongly depend on PC speed, LPT port type and
operating system free resources. Therefore values of two
different PC configuration are given for comparison.
Device Operation Time A Time B
Temic programming and verify 44 sec 42 sec
T89C51RD2-M
ICSI programming and verify 10 sec 9 sec
IS89LV52A

Time A conditions: AMD Athlon 700MHz, 256MB RAM, ECP

MB LPT, WinXP.
Time B conditions: Intel P4 2GHz, 256MB RAM, ECP MB
LPT, WinXP.
For other specification see on Common notes / Common
technical specification.

14
 ELNEC s. r. o.

PICmicro
microcontrollers
multiprogramming

15
 ELNEC s. r. o.

Introduction
PICmicro microcontrollers multiprogramming supports
Microchip PICmicro microcontrollers, based on both EPROM
and Flash technology, up to 8 devices simultaneously. The
replaceable family&socket submodule permits different
package type support. There are available family&socket
submodules for device in DIL package (up to 40 pins) and
other packages.

PICmicro microcontrollers multiprogramming has

optimized advanced pindriver that deliver programming
performance without overshoot or ground bounce for all
memory technologies. Pin drivers operate down to 1.8V so
you'll be ready to program the full range of today's advanced
low-voltage devices.

PICmicro microcontrollers multiprogramming provides very

competitive price but excellent hardware design for reliable
programming.

16
 ELNEC s. r. o.

PICmicro microcontrollers
multiprogramming elements
! submodule for PICmicro microcontrollers with two ZIF (Zero
Insertion Force)
# Common multiprogramming module no.1
$ JetProg, base unit

Note: please call for other family&socket submodules

availability

Problems related to the JetProg ⇔

multiprogramming module ⇔ family&socket
submodule interconnection
If you have any problems with JetProg ⇔ multiprogramming
module ⇔ family&socket submodule interconnection see
section Common notes.

17
 ELNEC s. r. o.

Technical specification
• PICmicro microcontroller compatible pindriver (8x)
• pindrivers are independent, therefore defective chip haven't
influence to another programmed chips
• perfect ground and necessary supply/programming voltage
can be applied independently to each socket of module
• TTL pindriver meet PICmicro microcontroller requirements
• current limitation for each socket, overcurrent shutdown,
power failure shutdown
• banana hole for ESD wrist straps
• insertion test

Accepted family&socket submodules

For list and short descriptions of accepted family&socket
submodules see at Appendix.

DEVICE SUPPORT
• EPROM based Microchip PICmicro chips: PIC12Cxxx/
PIC16Cxxx/PIC18Cxxx series
• Flash based Microchip PICmicro chips: PIC12Fxxx/
PIC16Fxxx/PIC18Fxxx series
Check please the list of all supported devices for details.

Programming speed
Notes:
• given values are measured under all 8 devices together
condition
• this times strongly depend on PC speed, LPT port type and
operating system free resources. Therefore values of two
different PC configuration are given for comparison.
Device Operation Time A Time B
PIC16C67 programming and verify 18 sec 15 sec
PIC16F877A programming and verify 11 sec 8 sec
PIC18F452 programming and verify 17 sec 14 sec
Time A conditions: Pentium MMX, 250 MHz, ECP/EPP,
WIN98.
Time B conditions: Athlon, 750 MHz, ECP/EPP on PCI bus,
WIN98
For other specification see on Common notes / Common
technical specification

18
 ELNEC s. r. o.

Software

19
 ELNEC s. r. o.

The module package contains a CD with the Windows control

program, useful utilities and additional information. This
module is not supported by DOS control program. The
permission to freely copy the content of the CD is granted in
order to demonstrate how ELNEC's programmers work.
Differences and modifications to this manual (if they exist) may
be found in www.elnec.com.

Installing of JetProg multiprogramming

system software
When you buy multiprogramming module together with JetProg
programmer, installing programmer software by instruction in
manual for JetProg. It is possible, that version of control
program delivered with JetProg and with module is not same.
Please, install the latter version of control program.

If you use JetProg programmer before, check used version of

control program. If you have older version as delivered with
module, install latter version too.

New versions of JetProg multiprogramming

system software
In order to exploit all the capabilities of module (programmer)
we recommend using the latest version of PG4UW (see
Manual for programmer Appendix B - Keep-Current Service).
You may download the latest version of programmer software
(file PG4UWARC.EXE) from our Internet site www.elnec.com,
part download. You may also obtain a CD with this file by snail-
mail (a mailing charge will apply).

Upgrading the programmer software

Copy PG4UWARC.EXE to a temporary directory then launch
it. You may delete all files from the temporary folder after the
installation process is complete.

Using the programmer software

The control program delivered by ELNEC, included on the

CD in your package, is granted to be free from any viruses
at the moment of delivery. To increase their safety our
programs include a special algorithm for detecting possible
virus infections.

20
 ELNEC s. r. o.

Run the control program

in Windows environment: double click to icon PG4UW.

After start, control program PG4UW automatically scans all

existing ports and searches for the connected any ELNEC's
programmer. Program PG4UW is common for all the ELNEC's
programmers, hence program try to find all supported (JetProg,
LabProg+, SmartProg, PREPROM-02aLV, T51prog,
51&AVRprog, PIKprog+, PIKprog and SEEprog) programmers.

Notes: When the PG4UW program is started, program is

checked for its integrity. Than the program display a standard
user menu and waits for your instructions.

If the control program cannot communicate with the

programmer, continue by Manual for programmer part The
programmer software / Run the control program.

21
 ELNEC s. r. o.

Description of the user screen

Windows program PG4UW
View mode

Program settings Socket status window

New items for multiprogramming mode

View mode Change between graphical or text

displaying of sockets status

Program settings Display base program settings

Socket status window Graphical displaying of sockets status

22
 ELNEC s. r. o.

Info window
Grafical display of results

Repeat last activity Progress indication window Text display of results

Graphical display of Display results of actions with devices in

results active sockets in graphical form.
Repeat last activity Question for repeat last actions with
devices.
Progress indication Display progress of actions with devices in
window numeric and graphical form.
Text display of results Display results of actions with devices in
active sockets in text form. Display serial
number for device too.

23
 ELNEC s. r. o.

Common notes

25
 ELNEC s. r. o.

Common technical specification

SOFTWARE
• Algorithms: only manufacturer approved or certified
algorithms are used. Custom algorithms are available at
additional cost.
• Algorithm updates: software updates are available approx.
every 2 weeks, free of charge.
• Main features: revision history, session logging, on-line help,
device and algorithm information.

Device operations
• standard:
• intelligent device selection by device type, manufacturer or
typed fragment of part name
• automatic ID-based selection of EPROM/Flash EPROM
• blank check, read, verify
• program
• erase
• checksum
• security:
• insertion test, reverse insertion check
• ID byte check
• special:
• auto device serial number increment
• statistic
• count-down mode

Buffer operations
• view/edit, find/replace
• fill/copy, move, byte swap, word/dword split
• checksum (byte, word)
• print

Supported file formats

• binary
• HEX: Intel, Intel EXT, Motorola S, MOS, Exormax, Tektronix,
ASCII-SPACE-HEX

26
 ELNEC s. r. o.

GENERAL

Recommended PC system requirements

• Processor: Pentium 100 MHz, 32 MB RAM
• Hard disk with 10 MB free space
• Operating system: Windows 95
• Free parallel (printer) port on PCI bus, IEEE 1284 compatible
(ECP/EPP)
Note: For convenience, we suggest that you use a
supplementary multi I/O card to provide an additional printer
port (LPT2 for example), in order to avoid sharing the same
LPT port between printer and programmer.

Operation
• power supply: from JetProg programmer (use switching
power supply adapter 100-240VAC/15VDC/1A)
• dimensions 275x135x20 mm (10.8"x5.3"x0.78") without
submodules. The connectors haven't influence to
programmer & module height.
• weight (without external adapter) 750g
• temperature 5°..40°C
• humidity 20%..80%, non condensing

Base configuration package for

multiprogramming module includes
• Common multiprogramming module no.1 (or EPROM/Flash
8-socket module)
• ZIF family&socket submodules - according to order
• for some countries switching power supply adapter 100-
240VAC/15VDC/1A
• user manual
• registration card
• software
• transport case

Additional services
• Keep Current.
• AlgOR
• free technical support (phone/fax/e-mail).
• free lifetime software update via Web site.

27
 ELNEC s. r. o.

JetProg ⇔ multiprogramming module ⇔

family&socket submodule interconnection
• switch off JetProg programmer
• extract DIL48 socket module
• insert multiprogramming module to JetProg programmer
• very carefully insert same family&socket submodules to
appropriate multiprogramming module connectors, to avoid
bad insertion of them. You needn’t insert family&socket
submodule to all positions.
• switch on JetProg programmer, use. power adaptor
delivered with multiprogramming module. This isn’t
necessary, if your JetProg programmer was delivered with
switching power supply adapter 100-240VAC/15VDC/1A
• run control program or by command Options / Find
programmer, program find programmer automatically and
set him to multiprogramming mode

Insert / change socket submodule

• switch off JetProg programmer
• remove family&socket submodule / insert other (all used
family&socket submodules must be the same type). Very
carefully insert family&socket submodules to appropriate
multiprogramming module connectors, to avoid bad
insertion of them.
• run control program or by command Options / Find
programmer, program find programmer automatically and
set him to multiprogramming mode

Connecting ESD wrist strap

On the rear side of multiprogramming module is banana hole
for connecting ESD wrist strap. Reduction resistor protects this
connection. ESD wrist strap you can connect to banana hole
directly.

Note: ESD wrist strap is not standard delivery

28
 ELNEC s. r. o.

Appendix

29
 ELNEC s. r. o.

Accepted family&socket submodule

EPROM / EEPROM / Flash EPROM

multiprogramming
EPROM/Flash-DIL32-2 submodule
• fits for EPROM/Flash in DIL28 and DIL32 packages
• 2x ZIF DIL32 sockets accepts both 300/600 mil devices
• operation life of ZIF sockets - 25.000 actuations
• ord. no.: 70-0105
EPROM/Flash PLCC32-2-DIL32 submodule
• fits for PLCC32 EPROM/Flash, features 32 pins in DIL
(27C010 and above, 29C512 and above)
• 2x ZIF PLCC32 sockets
• operation life of ZIF sockets - 10.000 actuations
• ord. no.: 70-0106
EPROM/Flash PLCC32-2-DIL28 submodule
• fits for PLCC32 EPROM/Flash, features 28 pins in DIL (e.g.
27C256, 27C512, 29C256, etc.)
• 2x ZIF PLCC32 sockets
• operation life of ZIF sockets - 10.000 actuations
• ord. no.: 70-0107

MCS-51 series microcontrollers

multiprogramming
MCS51-DIL40-2-1 submodule
• fits for standard-pinout MCS-51 in DIL40 package
• 2x ZIF DIL40 sockets
• operation life of ZIF sockets - 25.000 actuations
• ord. no.: 70-0148

PICmicro microcontrollers multiprogramming

PIC-DIL40-2-1 socket submodule
• fits for PICmicro controllers PIC12xxx, PIC16xxx and
PIC18xxx up to DIL40 package
• 2x ZIF DIL40 sockets
• operation life of ZIF sockets - 25.000 actuations
• ord. no.: 70-0149

30