For more information contact:

LMDB-1
American Crane & Equipment Corp.
Authorized Distributor
Tel: 877-503-2972
Fax: 484-945-0430
[email protected]
www.americancrane.com
Dimensional
DataBook
Dimensional Information
Little Mule Products
Publications LMC-2 and LMU-3

Cable • Lineman’s Strap • Ratchet Lever • Hand Chain • Electric Chain Hoists • Wire Grips • Trolleys • Beam Clamps • Accessories
Products To Pull You Through
The Tough Jobs

®
Little Mule Products ®
Little
Make Mule
Your Job Products
Easier and
Make Your Costs
Keep Your Job Easy
Downand
Keep Your Costs Down

Please Call (800) 477-5003 For More Information

TABLE OF CONTENTS

4, 5 Hoisting Do’s & Don’ts

6 Cable Puller
7 Lineman’s Strap Hoist
8 LMSB
9 LMR
10 LMHA
11 FEL
12 SLM
13 LMES
14 LMTD
15 LMTP (G)
16 Wire Grips
17 Beam Clamp
18 RA
19 G Model
20 Warranty

3
Manually Operated Hoists

Safe Hoisting Operations

Recommendations To Avoid Injury and Property Damage

Do’s Don’ts
1. Do read ASME/ANSI B30 Series Safety Standard for 1. Do Not lift or pull more than rated load.
Manually Operated Hoists and check with ANSI for any 2. Do Not use hoist load limiting device to measure the load.
further revisions.
3. Do Not use damaged hoist or hoist that is not working
2. Do read Hoist Manufacturer's Operating and Maintenance correctly.
Instructions.
4. Do Not use hoist with twisted, kinked, damaged, or worn
3. Do be familiar with operating controls, procedures, and chain.
warnings on the unit.
5. Do Not lift a load unless chain is properly seated in chain
4. Do make sure that the unit is securely attached to a suitable wheel(s) or sprocket(s).
support before applying load.
6. Do Not use load chain as a sling or wrap load chain around
5. Do maintain firm footing or be otherwise secured when the load.
operating unit.
7. Do Not lift a load if any binding prevents equal loading on
6. Do make sure that load slings or other approved single all supporting chains.
attachments are properly sized and seated in the hook saddle.
8. Do Not apply the load to the tip of the hook.
7. Do make sure the hook latches, if used, are closed and not
supporting any part of the load. 9. Do Not operate unless load is centered under hoist.
8. Do make sure that the load is free to move and will clear all 10. Do Not operate the unit when it is restricted from adjusting
obstructions. itself to form a straight line with the direction of loading.
9. Do take up slack carefully, check the load balance, move the 11. Do Not operate hoist with other than manual power.
load a few inches, and check load holding action before 12. Do Not permit more than one operator to pull on a single
continuing. hand chain or lever at one time.
10. Do make sure all persons stay clear of the suspended or 13. Do Not operate unit with any lever extension (cheater bar).
supported load. 14. Do Not allow your attention to be diverted from operating
11. Do avoid swinging of load or load hook. the hoist.
12. Do protect load chain from weld spatter or other damaging 15. Do Not operate hoist beyond limits of load chain travel.
contaminants. 16. Do Not use hoist to lift, support, or transport people.
13. Do avoid “fly-back” by keeping a firm grip on the lever 17. Do Not lift loads over people.
(ratchet lever hoist) until operating stroke is completed and
the lever is at rest. 18. Do Not leave a suspended load unattended unless specific
precautions have been taken.
14. Do promptly report any malfunction, unusual performance, or
damage of the unit. 19. Do Not attempt to "free chain" unit with any load applied.
15. Do inspect unit regularly, replace damaged or worn parts, and 20. Do Not allow sharp contact between two hoists or between
keep appropriate records of maintenance. hoist and obstructions.
16. Do use the Hoist Manufacturer's recommended parts when 21. Do Not allow the chain or hook to be used as a ground for
repairing unit. welding.
17. Do use hook latches wherever possible. 22. Do Not allow the chain or hook to be touched by a live
welding electrode.
18. Do apply lubricant to load chain as recommended by the
Hoist Manufacturer. 23. Do Not remove or obstruct the warnings on the hoist.
24. Do Not adjust or repair a hoist unless qualified to perform
hoist maintenance.
25. Do Not attempt to lengthen the load chain or repair damaged
4 load chain.
 Electric & Air Powered Hoists
Chain and Wire Rope

Safe Hoisting Operations

Recommendations To Avoid Injury and Property Damage

Do’s Don’ts
1. Do read ASME/ANSI B30 Series Safety Standard for Electric 1. Do Not lift more than rated load.
and Air Powered Hoists and check with ANSI for any further 2. Do Not use hoist load limiting device to measure the load.
revisions.
3. Do Not use damaged hoist or hoist that is not working
2. Do read Hoist Manufacturer's Operating and Maintenance correctly.
Instructions.
4. Do Not use hoist with twisted, kinked, damaged, or worn
3. Do be familiar with operating controls, procedures, and wire rope or chain.
warnings on the unit.
5. Do Not lift a load unless wire rope is properly seated in its
4. Do make sure hook travel is in the same direction as shown groove(s) or unless chain is properly seated in chain wheel(s)
on controls. or sprocket(s).
5. Do make sure hoist limit switches function properly. 6. Do Not use load rope or load chain as a sling or wrap load
6. Do maintain firm footing when operating hoist. rope or load chain around the load.
7. Do make sure that load slings or other approved single 7. Do Not lift a load if any binding prevents equal loading on
attachments are properly sized and seated in the hook saddle. all supporting ropes and chains.
8. Do make sure the hook latches, if used, are closed and not 8. Do Not apply the load to the tip of the hook.
supporting any part of the load. 9. Do Not operate unless load is centered under hoist.
9. Do make sure that the load is free to move and will clear all 10. Do Not allow your attention to be diverted from operating
obstructions. the hoist.
10. Do take up slack carefully, check the load balance, move the 11. Do Not operate hoist beyond limits of load rope or load
load a few inches, and check load holding action before chain travel.
continuing.
12. Do Not use limit switches as routine operating stops unless
11. Do avoid swinging of load or load hook. recommended. They are emergency devices only.
12. Do make sure that all persons stay clear of the sus- 13. Do Not use hoist to lift, support, or transport people.
pended load.
14. Do Not lift loads over people.
13. Do warn personnel of an approaching load.
15. Do Not leave a suspended load unattended unless specific
14. Do protect wire rope and load chain from weld spatter or precautions have been taken.
other damaging contaminants.
16. Do Not allow sharp contact between two hoists or between
15. Do promptly report any malfunction, unusual performance, hoist and obstructions.
or damage of the unit.
17. Do Not allow the wire rope, chain, or hook to be used as a
16. Do inspect unit regularly, replace damaged or worn parts, and ground for welding.
keep appropriate records of maintenance.
18. Do Not allow the wire rope, chain, or hook to be touched by
17. Do use the Hoist Manufacturer's recommended parts when a live welding electrode.
repairing unit.
19. Do Not remove or obstruct the warnings on the hoist.
18. Do use hook latches wherever possible.
20. Do Not adjust or repair a hoist unless qualified to perform
19. Do apply lubricant to the wire rope or load chain as recom- hoist maintenance.
mended by the Hoist Manufacturer.
21. Do Not attempt to lengthen the load chain or repair damaged
load chain.

5
 Country Club Road
P.O. Box 779
CABLE PULLER HOISTS Wadesboro, NC 28170
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

Cable 1/2 - 2 Ton

F G

Minimum Stroke Angle

M (Degrees)
C

E
A

Dimensions
All Dimensions in Inches Except M

Model Rated Load (Lbs.) A A B C D E F G M

Number single double single double

115SA 1000 — 191/4 — 1 7/8 1 165/8 183/4 6 21o

115DA 1000 2000 191/4 271/2 1 7/8 1 165/8 183/4 6 21o
505NA 1500 — 193/4 — 1 7/8 1 203/4 23 6 21o
202WNA 1500 3000 193/4 277/8 1 7/8 1 203/4 23 6 21o
434WNA 1500 3000 203/4 291/4 1
1 /16 7/8 1 211/4 233/4 61/2 19o
430CDPA 1500 3000 223/4 333/4 13/16 13/16 11/4 211/4 233/4 61/2 19o
404WNA 2000 4000 211/4 291/2 11/16 7/8 1 251/4 273/4 61/2 19o

6
Country Club Road
P.O. Box 779
Wadesboro, NC 28170 LINEMANS STRAP HOISTS
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

Strap 3/4 - 2 Ton

Dimensions
Model Rated Load (Lbs.) A* A** B C D E∞ F∞
Number SingleLine DoubleLine SingleLine DoubleLine

322B 1500 3000 19 23 0.94 0.97 0.97 25.5 27.75

344B 2000 4000 19.32 29.32 1.06 1.06 0.97 31.5 33.75

Note: All Dimensions in Inches

* With idler removed.
** Model 322B (stiching is wrapped around idler)
Model 344B (stitching will NOT wrap around idler)
∞ For Hotstick Models add 1.5” to dimension E and F

7
 Country Club Road
P.O. Box 779
Wadesboro, NC 28170
RA T C H E T L EV E R H O I S T S Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

LMSC 3/4 - 6 Ton

Dimensions
Rated
Load No. of
Model No. (Lbs.) A B C D E F G H J K L Load Chains

LMSC1500 1500 115/8 13/16 15/16 91/4 117/16 5.59 2.06 3.54 4.72 9° 1.50 1
LMSC3000 3000 13 11/16 11/4 149/16 17 6.42 2.54 3.87 5.45 9° 1.62 1
LMSC6000 6000 16 15/16 13/8 17/32 149/16 18 3/16 7.28 3.22 4.03 7.00 9° 2.10 1
LMSC12000 12000 223/4 21/16 13/4 149/16 20 5/16 7.28 3.22 4.03 10.20 9° 3.34 2

All dimensions are in inches unless otherwise indicated.

8
Country Club Road
P.O. Box 779
Wadesboro, NC 28170
Phone (800) 477-5003
RA T C H E T L EV E R H O I S T S
FAX (800) 374-6853
e-Mail [email protected]

LMR 3/4 - 3 Ton

Dimensions
Model Rated
Number Load (Ton) A B C D E F G H J K

LMR-1500 3/4 12 13/16 3/4 12 61/4 2 41/4 17/8 21/4 41/8

LMR-2000 1 13 1 1 12 61/4 2 41/4 17/8 2 5/8 41/2
LMR-3000 11/2 141/2 13/16 11/8 12 7 3 41/4 23/8 31/4 55/8
LMR-6000 3 171/2 13/8 13/8 16 81/2 33/4 41/4 3 33/4 63/4

All dimensions are in inches unless otherwise indicated.

9
 Country Club Road
P.O. Box 779
HAND CHAIN HOISTS Wadesboro, NC 28170
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

LMHA 1/2 - 50 Ton

Dimensions
Model Rated No. of
Number Load (Ton) A B C D E F G H J K Load Chains

LMHA-1/2B 1/2 101/4 57/16 57/16 51/4 5/16 5/8 33/8 7/16 215/16 31/4 1
LMHA-1B 1 113/16 515/16 61/4 6 11/8 5/16 41/16 5/8 319/32 37/16 1
LMHA-11/2B 11/2 15 3/4 61/2 71/4 61/8 15/16 11/8 39/16 13/16 4 35/8 1
LMHA-2B 2 15 71/4 87/16 81/2 13/8 11/4 415/16 7/8 49/16 37/8 1
LMHA-3B 3 171/8 713/16 10 10 19/16 11/2 53/4 11/8 57/16 43/8 1
LMHA-5B 5 22 5/8 61/2 111/8 75/16 17/8 113/16 613/16 13/8 61/2 35/8 3
LMHA-8B 8 321/2 713/16 151/16 — 23/4 21/2 917/32 113/16 83/4 43/16 3
LMHA-10B 10 321/2 713/16 151/16 — 23/4 21/2 917/32 113/16 83/4 43/16 3
LMHA-12B 12 505/8 713/16 205/16 — 215/16 227/32 113/16 27/16 1011/16 43/16 5
LMHA-15B 15 505/8 713/16 205/16 — 215/16 227/32 113/16 27/16 1011/16 43/16 5
LMHA-20B 20 523/8 121/8 287/8 — 31/8 39/16 129/16 39/16 121/2 61/16 6
LMHA-25B 25 527/8 141/2 287/8 — 31/8 31/2 129/16 39/16 121/2 71/4 8
LMHA-30B 30 65 167/8 295/8 — 43/16 431/32 183/16 47/16 153/16 87/16 10
LMHA-40B 40 735/16 201/8 295/8 — 41/16 63/16 221/4 51/4 175/8 101/16 14
LMHA-50B 50 775/8 257/8 295/8 — 43/4 63/4 233/4 67/8 201/4 1215/16 20

Dimensions are in inches unless otherwise indicated.

10
Country Club Road
P.O. Box 779
Wadesboro, NC 28170 ELECTRIC CHAIN HOISTS
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

FEL 1/4 - 2 Ton

**

Hoist Dimensions Hoist Dimensions

Rated
Model Load B B Number
Number (Lbs.) 1-PH 3-PH Of Chains A* D E F G
FEL-0232 250 91/8” 8 1/8” SINGLE 18” 4” 1” 7/ 8” 11/16”
FEL-0516 500 91/8” 8 1/8” DOUBLE 22” 4 7/8” 11/8” 15/16” 11/4”
FEL-0532 500 91/8” 8 1/8”
FEL-1016 1000 91/8” 8 1/8” NOTE: All units single chain except 2 ton.
FEL-1032 1000 10 1/8” 8 5/8” * “A” Dimension allows 2” clearance between **
FEL-2016 2000 10 1/8” 8 5/8” load block and underside of hoist on single
chain models and 1” on double chain models.
FEL-4008 4000 10 1/8” 8 5/8”

CHAIN CONTAINER
Capacity
(Hoist Lift In Feet)

FEL FEL C
Part 1 Ton & Under 2 Ton
Number C (Single Chain) (Double Chain)
JL927-1 111/2” 20’ 10’
JL927-3 181/2” 35’ 17’
JL927-4 27” 50’ 25’

Chain Container Option

11
 Country Club Road
P.O. Box 779
ELECTRIC CHAIN HOISTS Wadesboro, NC 28170
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

SLC 1/8 - 1/2 Ton

Reeving A B C D
single 111/16 3 7/8 2 15/16 3
double 12 1/8 5 3/4 2 3/8 3 9/16
All dimensions in inches

* Dimension based on 10 ft. lift—

will vary depending on actual lift

12
Country Club Road
P.O. Box 779
Wadesboro, NC 28170 ELECTRIC CHAIN HOISTS
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

LMES 1/4 - 1/2 Ton

C
D H J

E B

K
A

Dimensions
Rated
Model Load
Number (Ton) A B C D E F H J K L

LMES-0512-10 1/4 15 3 2 51/4 3/4 3/4 6 33/4 41/4 81/2

LMES-0512-20 1/4 15 3 2 51/4 3/4 3/4 6 33/4 41/4 81/2
LMES-0512-10 1/2 15 3 2 51/4 3/4 3/4 6 33/4 41/4 81/2

Dimensions are in inches unless otherwise indicated.

13
 Country Club Road
P.O. Box 779
P LA I N T R O L L EY S Wadesboro, NC 28170
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

LMTD 1/4 - 5 Ton

Dimensions
Model Rated Flange
Number Load (Ton) A B C D F J K L M N Width Radius

LMTD-500 1/4 37/8 41/8 117/64 113/4 9/16 21/4 37/16 3/8 89/16 7/8 2.66 - 8.05 36
LMTD-1000 1/2 37/8 41/8 117/64 113/4 9/16 21/4 37/16 3/8 89/16 7/8 2.66 - 8.05 36
LMTD-2000 1 37/8 49/16 21/4 12 1/2 23/4 41/16 1/2 97/8 7/8 3.00 - 8.05 48
LMTD-3000 11/2 47/8 61/4 21/4 125/8 5/8 41/4 53/4 1/2 131/2 11/4 3.33 - 8.05 60
LMTD-4000 2 47/8 61/4 21/4 125/8 5/8 41/4 53/4 1/2 131/2 11/4 3.33 - 8.05 60
LMTD-6000 3 45/8 63/8 21/4 133/8 23/32 41/4 53/4 1/2 141/8 11/4 4.00 - 8.05 60
LMTD-10000 5 53/8 63/4 21/2 143/4 15/16 43/8 63/16 5/8 157/16 15/8 4.60 - 8.05 60

NOTE: All dimensions in inches unless otherwise indicated.

14
Country Club Road
P.O. Box 779
Wadesboro, NC 28170 P LA I N & G EA R E D T R O L L EY S
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

LMTP(G) 8 - 16 Ton

GEARED PLAIN

Rated
Model Load
A B C D E F G H I J K L M N O P
Number (Tons)
LMTP(G)-16000 8 235/8 105/8 37/8 105/8 13/8 31/2 61/2 9 1/8 111/16 10 81/4 21/2 3/4 31/4 67/8
LMTP(G)-20000 10 235/8 105/8 37/8 111/8 13/8 41/2 8 9 1/8 111/16 10 81/4 21/2 1 31/4 67/8
LMTP(G)-24000 12 235/8 105/8 37/8 111/8 13/8 41/2 8 9 1/8 111/16 10 81/4 21/2 1 31/4 67/8
LMTP(G)-32000 16 281/4 14 57/8 151/4 21/2 4 9 141/2 5/16 2 131/2 113/4 31/4 11/2 7 8

Notes: All dimensions are in inches.

Wheels with convex treads are standard on all capacities.
20, 25, 30 and 40 ton trolleys can be furnished in tandem construction - 30 and 40 ton dimensions furnished upon application.
* Dimensions shown are for minimum beam size and will vary proportionately for larger beams.

Model Beam
Number Radius Size

LMTP(G)16000 72 10 - 24
LMTP(G)20000 72 10 - 24
LMTP(G)24000 72 10 - 24
LMTP(G)32000 96 18 - 24

15
 Country Club Road
P.O. Box 779
WIRE GRIPS Wadesboro, NC 28170
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

WG 1/2 - 10 Ton

SPECIFICATIONS Standard and Hot Line Models 1,000 - 20,000 Lbs.

Wire Size
Net Minimum Maximum Handle
Model Capacity Weight Eye Opening
Number Type (Lbs.) (Lbs.) Size (In.) Guage Size (In.) Guage (In.)

LMG1000 1000 1 /2 .04 18AWG .394 1/0AWG .625 dia.

LMG2000 2000 1 .109 8AWG .594 4/0AWG 1 x 11/2
LMG4500 Standard Grip 5000 31/4 .18 6AWG .60 4/0AWG 1 1/ 4 x 1 3/ 4
LMG4600 Spring Loaded 10000 41/2 .30 1AWG .80 450MCM 1 1/ 4 x 1 3/ 4
LMG4800 12000 8 .70 397MCM 1.25 1130MCM 1 1/ 4 x 1 3/ 4
LMG4700 20000 21 .70 397MCM 1.25 1130MCM 2 1/ 2 x 3 1/ 2
LMG4501 5000 31/4 .18 6AWG .60 4/0AWG 1 1/ 4 x 1 3/ 4
Hot Line Grip
LMG4601 10000 41/2 .30 1AWG .80 450MCM 1 1/ 4 x 1 3/ 4
Spring Loaded
LMG4801 12000 8 .70 397MCM 1.25 1130MCM 1 1/ 4 x 1 3/ 4
Notched Handle
LMG4701 20000 21 .70 397MCM 1.25 1130MCM 2 1/ 2 x 3 1/ 2
LMG4502 5000 31/4 .18 6AWG .60 4/0AWG 1 1/ 4 x 1 3/ 4
Hot Line Grip
LMG4602 No Spring 10000 41/2 .30 1AWG .80 450MCM 1 1/ 4 x 1 3/ 4
LMG4802 No Notch 12000 8 .70 397MCM 1.25 1130MCM 1 1/ 4 x 1 3/ 4
LMG4702 20000 21 .70 397MCM 1.25 1130MCM 2 1/ 2 x 3 1/ 2

Note: 1000 and 2000 lb. models have Bulldog-type

jaw with aggresive teeth. All other models have Model A B C D E
parallel jaw. All dimensions in inches. LMG1000 55/16 27/16 5/8 5/8 —
LMG2000 73/4 31/8 11/2 1 —
DIMENSIONAL DRAWING - Wire Grips LMG4500 11 41/4 2 11/4 —
LMG4600 113/4 51/4 21/4 13/8 —
LMG4800 133/4 51/4 21/4 13/8 —
E LMG4700 195/8 71/4 35/8 29/16 —
LMG4501 11 5 2 21/4 1
D
LMG4601 123/4 57/8 21/4 13/8 13/16
B LMG4801 133/4 61/2 21/4 13/8 13/16
C
LMG4701 195/8 81/4 35/8 29/16 1
LMG4502 11 5 2 11/4 1
LMG4602 123/4 57/8 21/4 13/8 13/16
A LMG4802 133/3 61/2 21/4 13/8 13/16
Hot Line Model Shown LMG4702 195/8 81/4 35/8 29/16 1

16
Country Club Road
P.O. Box 779
Wadesboro, NC 28170 BEAM CLAMPS
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

BC 1 - 10 Ton

Specifications
Rated Flange Net
Model Load Width Weight
Number (Lbs.) (Ins.) (Lbs.)
BC-1 2000 3-9 8.8
BC-2 4000 3-9 13.2
BC-3 6000 3.2 - 12.6 17.6
BC-5 10000 3.6 - 12.2 22.0
BC-10 20000 3.6 - 12.6 32.0

Dimensions
Model A B C D E F G H
Number Max. Min. Max. (In.) (In.) (In.) Max. Min. Min.
BC-1 10.6 6.9 14.4 2.9 0.2 8.4 5.4 2.9 1.2 .80
BC-2 10.6 7.3 15.0 2.9 0.2 8.4 5.4 2.9 1.2 .80
BC-3 11.6 8.7 16.7 4.0 0.3 10.0 6.3 4.1 2.4 .87
BC-5 12.6 9.8 18.7 4.0 0.3 10.0 6.3 3.5 1.8 1.10
BC-10 12.6 10.5 18.9 4.6 0.47 10.8 7.2 5.2 2.6 1.50

All dimensions are in inches unless otherwise indicated.

17
 Country Club Road
P.O. Box 779
RA T C H E T L EV E R H O I S T S Wadesboro, NC 28170
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

RA 3/4 - 6 Ton

Dimensions
Model Rated Load
Number (Lbs.) (Ton) A B C* D E F G H J K L M
RA-15 1500 3/4 127/16 1 1 6 201/2 23 45/8 15/8 3 51/4 9 36°
RA-20 2000 3/4 127/16 1 1 6 201/2 23 45/8 15/8 3 51/4 9 36°
RA-15-2 3000 11/2 171/4 15/16 1 71/8 201/2 233/4 45/8 15/8 3 55/8 101/8 36°
RA-30 3000 11/2 133/4 11/8 11/8 71/4 201/2 243/4 7 27/8 41/8 67/8 101/4 36°
RA-40 4000 11/2 133/4 11/8 11/8 71/4 201/2 243/4 7 27/8 41/8 67/8 101/4 36°
RA-30-2 6000 2 171/4 11/4 111/16 67/8 201/2 243/4 7 27/8 41/8 71/4 97/8 36°
RA-30-3 9000 41/2 22 13/8 111/16 71/2 201/2 243/4 7 27/8 41/8 81/8 101/2 36°
RA-30-4 12000 6 22 13/4 111/16 81/2 201/2 243/4 7 27/8 41/8 93/4 111/2 36°

* Hook throat opening with latch.

Note: Where clearance dimensions are critical, request certified print.
All dimensions are in inches unless otherwise indicated.

18
Country Club Road
P.O. Box 779
Wadesboro, NC 28170 RA T C H E T L EV E R - R O L L E R C HA I N H O I S T S
Phone (800) 477-5003
FAX (800) 374-6853
e-Mail [email protected]

G Model 3/4 - 15 Ton

SPECIAL SNAP HOOK

AND LINK
All multiple chain hoists through
six tons can be converted to next
smaller capacity to give longer lift
and faster operation. Conversion is made by
simply unhooking the special snap hook at the
end of the chain. The snap hook acts as a lug
and will not pass through the chain sprocket.

Dimensions
Model
Number A B C* D E F G H J K L M
AG 13 1 1 61/4 183/4 203/4 5 11/2 31/2 41/2 91/4 60°
AGI1 13 1 1 61/4 183/4 203/4 5 11/2 31/2 41/2 91/4 30°
ATG2 15 1 1 61/4 183/4 203/4 5 11/2 31/2 41/2 91/4 60°
ATGI1, 2 15 1 1 61/4 183/4 203/4 5 11/2 31/2 41/2 91/4 30°
FG 16 11/8 11/8 7 275/8 297/8 61/4 13/4 41/2 53/4 101/4 60°
FGI1 16 11/8 11/8 7 275/8 297/8 61/4 13/4 41/2 53/4 101/4 30°
FTG3 175/8 11/8 11/8 73/8 275/8 297/8 61/4 13/4 41/2 53/4 105/8 60°
FTGI1, 3 175/8 11/8 11/8 73/8 275/8 297/8 61/4 13/4 41/2 53/4 105/8 30°
ZG-41/24, ZG-65 25 113/16 111/16 81/4 335/8 361/8 61/8 111/16 47/16 61/8 127/8 60°
WG-9, WG-13
WG-11, WG-15 30 21/8 15/8 91/8 335/8 413/8 63/8 13/4 45/8 131/2 145/8 60°

1Double Pawls — can be operated with half strokes of lever for use in close quarters. **Minimum stroke on double locking pawl models
2Convertible model — 1 chain 3/4 ton, 112" lift. 2 chains 11/2 tons, 57" lift. (AGI, ATGI, FGI, FTGI) one-half (30°) that of
3Convertible model — 1 chain 11/2 tons, 112" lift. 2 chains 3 tons, 57" lift. single locking pawl models (AG, ATG, FG, FTG).
4Convertible model — 2 chain 3 tons, 76" lift. 3 chains 41/2 tons, 51" lift.
Where clearance dimensions are critical, request
certified print.
5Convertible model — 3 chain 41/2 tons, 70" lift. 4 chains 6 tons, 53" lift.

All dimensions are in inches unless otherwise indicated.

19
 E very Little Mule hoist is thoroughly inspected and improper or inadequate maintenance, eccentric or side
performance tested prior to shipment from the factory. loading, overloading, chemical or abrasive actions,
If any properly installed, maintained and operated hoist excessive heat, unauthorized modifications or repairs,
as outlined in the applicable accompanying Little Mule or use of non-Little Mule repair parts.
hoist manual develops a performance problem due to
defective materials or workmanship as verified by
Little Mule, repair or replacement of the hoist will be made
to the original purchaser without charge and the hoist EXCEPT AS STATED HEREIN, LITTLE MULE MAKES
will be returned, transportation prepaid. This warranty NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
does not apply where deterioration is caused by normal INCLUDING WARRANTIES OF MERCHANTABILITY
wear, abuse, improper or inadequate power supply, AND FITNESS FOR A PARTICULAR PURPOSE.

For more information contact:

American Crane & Equipment Corp.
Authorized Distributor
Tel: 877-503-2972
Fax: 484-945-0430
[email protected]
www.americancrane.com

Little Mule Products • Country Club Road • P.O. Box 779 • Wadesboro, North Carolina 28170 USA
Tel: (800) 477-5003 • (704) 694-2156 • Fax: (800) 374-6853 • (704) 694-6829
E-Mail: [email protected] • www.coffinghoists.com ©2003 Little Mule Products
LMDB-1
10M 07/03
Printed In USA