DATA SHEET

Liquid Level Switches

High Performance Series

FEATURES
• Liquid level switches that can detect almost any liquid type;
oil or water based
• Large load output; high switching currents
• Choice of threads and terminal connections

Housing/ Output Type / Logic Supply Output Temp

Mounting Voltage Current

BENEFITS OUTPUT VALUES

• Robust stainless steel housing Output Voltage (Vout): lout = 100mA
• Suitable for use within aggressive environments Vs = 4.5—15.4VDC
Output High Vout = Vs - 1.5V max
• Larger mounting threads; standard or custom
Output Low Vout = 0V + 0.5V max

TECHNICAL SPECIFICATIONS Output Voltage (Vout): lout = 800mA

Vs = 10—45VDC
Supply voltage (Vs) 4.5VDC to 15.4VDC (±5%)
Output High Vout = Vs - 1.8V max
or 10VDC to 45VDC (±5%)
Output Low Vout = 0V + 0.7V max
Supply current (ls) 15mA max. (Vs = 12VDC)
or 35mA max. (Vs = 45VDC)
Output sink and source 100mA max. (15.4VDC)
current (lout) or 800mA max. (45VDC)
Other sensor options available on request, email:
[email protected]
Operating temperatures Standard: -25°C to +80°C
Extended: -40°C to +125°C
Storage temperatures Standard: -30°C to +85°C
Need help? Ask the expert
Extended: -40°C to +125°C
Housing material Stainless Steel with Tel: + 44 (0)1236 459 020
Polysulfone tipa and ask for “Technical”
Sensor termination Various; refer to page 2

a) Before use check that the fluid in which you wish to use these devices is compatible with Stainless Steel and Polysulfone.
NOTES
 OUTLINE DRAWING HOUSING SPECIFICATIONS
All dimensions shown in mm. Tolerances = ±1mm. Installation drawings and 3D (.step) files available on the
product webpage.

Cable
Housing

3/4”-16
Thread 1/2” BSPP 3/8” BSPP 1/2” NPT
UNJF

Pressureb 25 bar / 363 psi maximum

Cable: 0.5m, 1m or 3m lengths (IP67)

Sensor M12x1 Brad Harrison micro (IP67)

Termination
Flying leads: 24AWG, 0.2m PTFE wires,
Brad Harrison micro 8mm tinned (IP65)

ELECTRICAL INTERFACE

Cable

Wire Designation
Red Vs
White Output
Black 0V
Flying Leads

Brad Harrison micro

Pin Designation
1 Vs

2 Not connected

3 0V
4 Output
Note: “X” can equal 0.5, 1.0 or 3.0 metres.

Flying Leads

Wire Designation
Red Vs
Green Output
Blue 0V

b) When sealed correctly.

NOTES
 CIRCUIT DIAGRAMS

In order to suit any application, these sensors have been designed with various output circuit configurations.
4.5V—15.4VDC

10V—45VDC

CAUTION: Take care when connecting loads.

The minimum load impedance should not exceed Vs/max output current.
Note: Shorting the output to Vs or 0V will result in irreparable damage to the sensor.
 ORDER INFORMATION
Generate your specific part number using the convention shown below. Use only those letters and numbers that correspond to the
sensor and output options you require — omit those you do not.

L L H P X X X X X X

Housing Housing Operating Internal Seal

Output Type / Logic Termination
Material Type Temp. Washer

A 1 2 2 0 D 1
Polysulfone Push Pull Push Pull Stainless Steel -25 °C M12x1 Brad Nitrile rubber
tip High in Air Low in Air 3/8” BSPP to +80°C Harrison (IP67)
(100mA, 4.5-15.4V) (100mA, 4.5-15.4V)

3 4 5 1 I 5
Push Pull Push Pull Stainless Steel -40 °C Cable 0.5m Viton
High in Air Low in Air 1/2” BSPP to +125°C (IP67)
(800mA, 10—45V) (800mA, 10—45V)

5 6 8 L
N-Type N-Type Stainless Steel Cable 1.0m
High in Air Low in Air 1/2” NPT (IP67)
(800mA, 10—45V) (800mA, 10—45V)

7 8 B M
P-Type P-Type Stainless Steel Cable 3.0m
High in Air Low in Air 3/4”-16 UNJF (IP67)
(800mA, 10—45V) (800mA, 10—45V)

P
Flying Leads
24AWG 0.2mm
(IP65)

Note: Not all combinations are configurable and minimum order quantities (MOQs) may apply in some cases.
Please contact SST Sensing for details; email: [email protected]

CAUTION INFORMATION
Do not exceed maximum ratings and ensure sensor(s) are operated in As customer applications are outside of SST Sensing Ltd.’s control, the
accordance with their requirements. information provided is given without legal responsibility. Customers
should test under their own conditions to ensure that the equipment is
Carefully follow all wiring instructions. Incorrect wiring can cause
suitable for their intended application. Before use, check that the fluid in
permanent damage to the device.
which you wish to use these devices is compatible with Stainless Steel
SST Sensing Ltd recommend using alcohol based cleaning agents. and Polysulfone.
Do NOT use chlorinated solvents such as trichloroethane as these are
likely to attack the sensor material. For technical assistance or advice, please email:
[email protected]
Failure to comply with these instructions may result in product
damage.

General Note: SST Sensing Ltd. reserves the right to make changes to product specifications without notice or liability.
All information is subject to SST Sensing Ltd.'s own data and considered accurate at time of going to print.

DS-0037 REV 11 © 2020 SST SENSING LTD.

5 H A GMI LL C RES CEN T, S HAWH EAD I ND US TR IAL ES TA TE , CO AT BR ID GE, U K M L5 4 NS
w w w.ssts ensi ng .com | e: sal es@ss tse nsin g.co m | t : + 44 ( 0 )12 36 4 5902 0 | f: +4 4 (0 ) 123 6 459 02 6